Thanks @por wifi's are up and working.
The problem is focused in download speed, not only in 23.05.5, in previous versions I had the same "problem", it's a long time ago issue with ath10k IMO.
That is fixed in this release (archer c7v5 non-ct fw)
1 Like
Maybe in Archer C7 is solved, but in DAP-2610 is not.
root@DAP2610:~# opkg list-installed | grep -i ath10
ath10k-board-qca4019 - 20230804-1
ath10k-firmware-qca4019 - 20230804-1
kmod-ath10k - 5.15.167+6.1.110-1-1
root@DAP2610:~#
Tested with CT and non-CT drivers.
iwinfo phy0-ap0 assoclist
Should show maximum NSS in both directions, the TX side (2nd line) used to fall back to one antenna stream without credible reason.
I can't tell, I just upgraded the device and left ! Last time I used it (.4) it worked just fine.
1 Like
I agree @brada4 but the same device, in the same place, with stock firmware a get full speed in download / upload (300 MB. fiber in my case).
CMCC RAX3000M, all OK, thanks.
1 Like
Zyxel GS1900-10HP v2: No issues.
Netgear GS108T v3: No issues.
Ubiquiti UniFi 6 Lite: FAIL - Image is accepted, wired network port works, but wireless radios are not detected. Radios appear as "unknown" in luci. no errors are seen in kernel/system logs. Rollback to 23.05.4 restores full function.
Banana Pi R3: BRICK (soft) - No issues noted on serial console, but no network ports function after upgrade. Rollback to 23.05.4 via U-Boot console results in config loss. Full function restored after loading config backup.
3 Likes
Upgraded GL.iNet Flint 2 (MT6000) - took only 2 mins using attended sysupgrade, kept all settings and appears to be working well so far. Thanks Devs and testers.
Edit - just one thing to ask, I'm not sure if I'm getting the full speed I should on the 5GHz wireless. I ran iperf3 -s from the router, and iperf3 -c [IP-Address] from my high spec Windows 11 machine (Intel AX211 6E wifi) and got the following results with 80-GHz channel width set. Should I expect to see higher speeds? (NB. I get roughly the same in 23.05.3)
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 26.5 MBytes 222 Mbits/sec
[ 5] 1.00-2.00 sec 25.8 MBytes 216 Mbits/sec
[ 5] 2.00-3.01 sec 25.4 MBytes 212 Mbits/sec
[ 5] 3.01-4.01 sec 24.8 MBytes 208 Mbits/sec
[ 5] 4.01-5.01 sec 25.0 MBytes 210 Mbits/sec
[ 5] 5.01-6.01 sec 25.0 MBytes 210 Mbits/sec
[ 5] 6.01-7.01 sec 24.4 MBytes 204 Mbits/sec
[ 5] 7.01-8.01 sec 26.0 MBytes 218 Mbits/sec
[ 5] 8.01-9.01 sec 25.2 MBytes 212 Mbits/sec
[ 5] 9.01-10.01 sec 25.5 MBytes 214 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.01 sec 254 MBytes 212 Mbits/sec sender
[ 5] 0.00-10.04 sec 252 MBytes 211 Mbits/sec receiver
1 Like
You need other high spec machine in LAN or on the internet to run test fully.
2 Likes
@happydashery that is very low yes. GL-MT6000 here too and seeing about 700 Mbps peak on 5GHz @ 80MHz in the same room as my router (~15 feet away). Just tested on my iPhone though can try PC tonight. I will clamp it down a little with AQL limits to optimize latency though.
Run tested and thanks for the great release devs, definitely recommended for most users. Back to snapshots for me.
2 Likes
Same for the WAX202. I had to add kmod-mt7915-firmware to my Firmware Selector package recipe. These recipe changes should be noted somewhere.
2 Likes
AX3000T all OK, thanks.
BusyBox v1.36.1 (2024-09-23 12:34:46 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.5, r24106-10cc5fcd00
-----------------------------------------------------
root@OpenWrt:~# iperf3 -c 192.168.1.4
Connecting to host 192.168.1.4, port 5201
[ 5] local 192.168.1.1 port 38832 connected to 192.168.1.4 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 113 MBytes 949 Mbits/sec 0 570 KBytes
[ 5] 1.00-2.00 sec 111 MBytes 933 Mbits/sec 0 570 KBytes
[ 5] 2.00-3.00 sec 112 MBytes 939 Mbits/sec 0 595 KBytes
[ 5] 3.00-4.00 sec 111 MBytes 932 Mbits/sec 0 595 KBytes
[ 5] 4.00-5.00 sec 112 MBytes 937 Mbits/sec 0 595 KBytes
[ 5] 5.00-6.00 sec 112 MBytes 940 Mbits/sec 0 595 KBytes
[ 5] 6.00-7.00 sec 112 MBytes 936 Mbits/sec 0 595 KBytes
[ 5] 7.00-8.00 sec 112 MBytes 936 Mbits/sec 0 595 KBytes
[ 5] 8.00-9.00 sec 112 MBytes 938 Mbits/sec 0 595 KBytes
[ 5] 9.00-10.00 sec 111 MBytes 934 Mbits/sec 0 595 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 1.09 GBytes 938 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 1.09 GBytes 937 Mbits/sec receiver
iperf Done.
root@OpenWrt:~# iperf3 -c 192.168.1.4 -R
Connecting to host 192.168.1.4, port 5201
Reverse mode, remote host 192.168.1.4 is sending
[ 5] local 192.168.1.1 port 55140 connected to 192.168.1.4 port 5201
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 112 MBytes 941 Mbits/sec
[ 5] 1.00-2.00 sec 112 MBytes 941 Mbits/sec
[ 5] 2.00-3.00 sec 111 MBytes 934 Mbits/sec
[ 5] 3.00-4.00 sec 112 MBytes 942 Mbits/sec
[ 5] 4.00-5.00 sec 112 MBytes 942 Mbits/sec
[ 5] 5.00-6.00 sec 112 MBytes 942 Mbits/sec
[ 5] 6.00-7.00 sec 112 MBytes 942 Mbits/sec
[ 5] 7.00-8.00 sec 112 MBytes 941 Mbits/sec
[ 5] 8.00-9.00 sec 112 MBytes 942 Mbits/sec
[ 5] 9.00-10.00 sec 112 MBytes 942 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 1.10 GBytes 943 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 1.10 GBytes 941 Mbits/sec receiver
iperf Done.
root@OpenWrt:~#
WiFi 5GHz 160MHz 40 iperf3 local
[SUM] 0.00-10.02 sec 1.94 GBytes 1.66 Gbits/sec sender
[SUM] 0.00-10.12 sec 1.93 GBytes 1.64 Gbits/sec receiver
4 Likes
I created my image for the WAX202 locally with imagebuilder and kmod-mt7915-firmware is included, although I did not specify it as an extra package. Did you use the online version of the image builder?
1 Like
Yes, we used the online Firmware Selector site.
I used: https://firmware-selector.openwrt.org/?version=23.05.5&target=ramips%2Fmt7621&id=netgear_wax202
1 Like
Upgraded fine on Intel NUC7CJYH.
1 Like
Works well on my workhorse WE826T. Heavily customized image (from src) with multiple SSIDs, sqlite3, tc, nft+ipt, custom dnsmasq, custom pdns_recursor, lighttpd, php, lua scripts.
... so 10 hours after update I have about 100 megabytes of traffic. And I just finished downloading ~20GB...
Can anyone confirm it? Xiaomi AX3200, if that's important
1 Like
TP-LINK Archer C2600 v1 and two Archer A7s updated using Luci from 23.05.4 to 23.05.5 with settings kept, missing packages installed and devices rebooted.
21 hours later all appears to be working normally*.
Thanks again to all who do the work to make this not just possible, but easy.
*[I am above the law.]
1 Like
Big thanks for the release!
Works fine on GL-iNet B1300 using attended sysupgrade.
Issues on banana pi r3 using attended sysupgrade (samba4-libs, luci-app-samba4, libjpeg-turbo, luci-app-vnstat2):
{
"url": "https://sysupgrade.openwrt.org",
"revision": "r24012-d8dd03c46f",
"advanced_mode": "1",
"sha256_unsigned": "",
"branch": "23.05",
"efi": null,
"profile": "bananapi,bpi-r3",
"target": "mediatek/filogic",
"version": "23.05.5",
"packages": [
"auc",
"base-files",
"block-mount",
"busybox",
"ca-bundle",
"cgi-io",
"collectd",
"collectd-mod-cpu",
"collectd-mod-df",
"collectd-mod-ethstat",
"collectd-mod-interface",
"collectd-mod-ipstatistics",
"collectd-mod-irq",
"collectd-mod-iwinfo",
"collectd-mod-load",
"collectd-mod-memory",
"collectd-mod-netlink",
"collectd-mod-network",
"collectd-mod-rrdtool",
"collectd-mod-syslog",
"collectd-mod-thermal",
"collectd-mod-wireless",
"dnsmasq",
"dropbear",
"e2fsprogs",
"eip197-mini-firmware",
"f2fsck",
"firewall4",
"fstools",
"fwtool",
"getrandom",
"hostapd-common",
"iw",
"iwinfo",
"jansson",
"jshn",
"jsonfilter",
"kernel",
"kmod-cfg80211",
"kmod-crypto-acompress",
"kmod-crypto-aead",
"kmod-crypto-authenc",
"kmod-crypto-ccm",
"kmod-crypto-cmac",
"kmod-crypto-crc32c",
"kmod-crypto-ctr",
"kmod-crypto-des",
"kmod-crypto-gcm",
"kmod-crypto-gf128",
"kmod-crypto-ghash",
"kmod-crypto-hash",
"kmod-crypto-hmac",
"kmod-crypto-hw-safexcel",
"kmod-crypto-manager",
"kmod-crypto-md5",
"kmod-crypto-null",
"kmod-crypto-rng",
"kmod-crypto-seqiv",
"kmod-crypto-sha1",
"kmod-crypto-sha256",
"kmod-crypto-sha512",
"kmod-fs-ext4",
"kmod-gpio-button-hotplug",
"kmod-hwmon-core",
"kmod-hwmon-pwmfan",
"kmod-i2c-gpio",
"kmod-leds-gpio",
"kmod-lib-crc-ccitt",
"kmod-lib-crc32c",
"kmod-lib-lzo",
"kmod-libphy",
"kmod-mac80211",
"kmod-mt76-connac",
"kmod-mt76-core",
"kmod-mt7915e",
"kmod-mt7986-firmware",
"kmod-nf-conntrack",
"kmod-nf-conntrack6",
"kmod-nf-flow",
"kmod-nf-log",
"kmod-nf-log6",
"kmod-nf-nat",
"kmod-nf-reject",
"kmod-nf-reject6",
"kmod-nfnetlink",
"kmod-nft-core",
"kmod-nft-fib",
"kmod-nft-nat",
"kmod-nft-offload",
"kmod-phy-aquantia",
"kmod-ppp",
"kmod-pppoe",
"kmod-pppox",
"kmod-sfp",
"kmod-slhc",
"kmod-thermal",
"kmod-usb-storage",
"kmod-usb2",
"kmod-usb3",
"libblobmsg-json",
"libc",
"libiwinfo",
"libiwinfo-data",
"libjson-c",
"libjson-script",
"liblucihttp",
"liblucihttp-ucode",
"libmbedtls",
"libmnl",
"libnftnl",
"libnl-tiny",
"libubox",
"libubus",
"libuci",
"libuclient",
"libucode",
"libustream-mbedtls",
"logd",
"luci",
"luci-app-attendedsysupgrade",
"luci-app-firewall",
"luci-app-nlbwmon",
"luci-app-opkg",
"luci-app-samba4",
"luci-app-statistics",
"luci-app-usteer",
"luci-app-vnstat2",
"luci-base",
"luci-light",
"luci-mod-admin-full",
"luci-mod-network",
"luci-mod-status",
"luci-mod-system",
"luci-proto-ipv6",
"luci-proto-ppp",
"luci-ssl",
"luci-theme-bootstrap",
"mkf2fs",
"mt7986-wo-firmware",
"mtd",
"nano-full",
"netifd",
"nftables-json",
"odhcp6c",
"odhcpd-ipv6only",
"openssh-client-utils",
"openssh-server-pam",
"openssh-sftp-client",
"openssh-sftp-server",
"openwrt-keyring",
"opkg",
"parted",
"ppp",
"ppp-mod-pppoe",
"procd",
"procd-seccomp",
"procd-ujail",
"px5g-mbedtls",
"resize2fs",
"rpcd",
"rpcd-mod-file",
"rpcd-mod-iwinfo",
"rpcd-mod-luci",
"rpcd-mod-rrdns",
"rpcd-mod-ucode",
"sshpass",
"ubi-utils",
"uboot-envtools",
"ubox",
"ubus",
"ubusd",
"uci",
"uclient-fetch",
"ucode",
"ucode-mod-fs",
"ucode-mod-html",
"ucode-mod-math",
"ucode-mod-ubus",
"ucode-mod-uci",
"uhttpd",
"uhttpd-mod-ubus",
"urandom-seed",
"urngd",
"usign",
"wireless-regdb",
"wpad-openssl"
],
"diff_packages": true,
"filesystem": "squashfs",
"client": "luci/git-23.339.51123-138595a"
}
STDERR:
Generate local signing keys...
Generate local certificate...
Package list missing or not up-to-date, generating it.
Building package index...
Downloading https://downloads.openwrt.org/releases/23.05.5/targets/mediatek/filogic/packages/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_core
Downloading https://downloads.openwrt.org/releases/23.05.5/targets/mediatek/filogic/packages/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/base/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_base
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/base/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/luci/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_luci
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/luci/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/packages/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_packages
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/packages/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/routing/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_routing
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/routing/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/telephony/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_telephony
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/telephony/Packages.sig
Signature check passed.
Downloading file:packages/Packages
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/imagebuilder
Downloading file:packages/Packages.sig
Signature check passed.
Collected errors:
* opkg_install_pkg: Checksum or size mismatch for package samba4-libs. Either the opkg or the package index are corrupt. Try 'opkg update'.
* opkg_install_cmd: Cannot install package luci-app-samba4.
* opkg_install_pkg: Checksum or size mismatch for package libjpeg-turbo. Either the opkg or the package index are corrupt. Try 'opkg update'.
* opkg_install_cmd: Cannot install package luci-app-vnstat2.
make[2]: *** [Makefile:189: package_install] Error 255
make[1]: *** [Makefile:154: _call_manifest] Error 2
make: *** [Makefile:274: manifest] Error 2
KR
1 Like