OpenWrt 23.05.5 - Service Release

RadioOperator · 2024-09-25T11:42:54.766Z

CMCC RAX3000M, all OK, thanks.

grauerfuchs · 2024-09-25T12:35:34.706Z

Zyxel GS1900-10HP v2: No issues.
Netgear GS108T v3: No issues.
Ubiquiti UniFi 6 Lite: FAIL - Image is accepted, wired network port works, but wireless radios are not detected. Radios appear as "unknown" in luci. no errors are seen in kernel/system logs. Rollback to 23.05.4 restores full function.
Banana Pi R3: BRICK (soft) - No issues noted on serial console, but no network ports function after upgrade. Rollback to 23.05.4 via U-Boot console results in config loss. Full function restored after loading config backup.

happydashery · 2024-09-25T12:49:29.563Z

Upgraded GL.iNet Flint 2 (MT6000) - took only 2 mins using attended sysupgrade, kept all settings and appears to be working well so far. Thanks Devs and testers.

Edit - just one thing to ask, I'm not sure if I'm getting the full speed I should on the 5GHz wireless. I ran iperf3 -s from the router, and iperf3 -c [IP-Address] from my high spec Windows 11 machine (Intel AX211 6E wifi) and got the following results with 80-GHz channel width set. Should I expect to see higher speeds? (NB. I get roughly the same in 23.05.3)

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  26.5 MBytes   222 Mbits/sec
[  5]   1.00-2.00   sec  25.8 MBytes   216 Mbits/sec
[  5]   2.00-3.01   sec  25.4 MBytes   212 Mbits/sec
[  5]   3.01-4.01   sec  24.8 MBytes   208 Mbits/sec
[  5]   4.01-5.01   sec  25.0 MBytes   210 Mbits/sec
[  5]   5.01-6.01   sec  25.0 MBytes   210 Mbits/sec
[  5]   6.01-7.01   sec  24.4 MBytes   204 Mbits/sec
[  5]   7.01-8.01   sec  26.0 MBytes   218 Mbits/sec
[  5]   8.01-9.01   sec  25.2 MBytes   212 Mbits/sec
[  5]   9.01-10.01  sec  25.5 MBytes   214 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.01  sec   254 MBytes   212 Mbits/sec                  sender
[  5]   0.00-10.04  sec   252 MBytes   211 Mbits/sec                  receiver

brada4 · 2024-09-25T12:58:58.855Z

You need other high spec machine in LAN or on the internet to run test fully.

phinn · 2024-09-25T13:13:11.770Z

@happydashery that is very low yes. GL-MT6000 here too and seeing about 700 Mbps peak on 5GHz @ 80MHz in the same room as my router (~15 feet away). Just tested on my iPhone though can try PC tonight. I will clamp it down a little with AQL limits to optimize latency though.

Run tested and thanks for the great release devs, definitely recommended for most users. Back to snapshots for me.

lleachii · 2024-09-25T13:23:42.959Z

jen1:

the WiFi will not work as the firmware for the WiFi chip is not installed by default.

por:

no WiFi radio's because the firmware package ath10k-firmware-qca9984-ct is not included in the build.

Same for the WAX202. I had to add kmod-mt7915-firmware to my Firmware Selector package recipe. These recipe changes should be noted somewhere.

janusz07 · 2024-09-25T13:29:09.579Z

AX3000T all OK, thanks.

BusyBox v1.36.1 (2024-09-23 12:34:46 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 23.05.5, r24106-10cc5fcd00
 -----------------------------------------------------
root@OpenWrt:~# iperf3 -c  192.168.1.4
Connecting to host 192.168.1.4, port 5201
[  5] local 192.168.1.1 port 38832 connected to 192.168.1.4 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   113 MBytes   949 Mbits/sec    0    570 KBytes       
[  5]   1.00-2.00   sec   111 MBytes   933 Mbits/sec    0    570 KBytes       
[  5]   2.00-3.00   sec   112 MBytes   939 Mbits/sec    0    595 KBytes       
[  5]   3.00-4.00   sec   111 MBytes   932 Mbits/sec    0    595 KBytes       
[  5]   4.00-5.00   sec   112 MBytes   937 Mbits/sec    0    595 KBytes       
[  5]   5.00-6.00   sec   112 MBytes   940 Mbits/sec    0    595 KBytes       
[  5]   6.00-7.00   sec   112 MBytes   936 Mbits/sec    0    595 KBytes       
[  5]   7.00-8.00   sec   112 MBytes   936 Mbits/sec    0    595 KBytes       
[  5]   8.00-9.00   sec   112 MBytes   938 Mbits/sec    0    595 KBytes       
[  5]   9.00-10.00  sec   111 MBytes   934 Mbits/sec    0    595 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  1.09 GBytes   938 Mbits/sec    0             sender
[  5]   0.00-10.00  sec  1.09 GBytes   937 Mbits/sec                  receiver

iperf Done.
root@OpenWrt:~# iperf3 -c  192.168.1.4 -R
Connecting to host 192.168.1.4, port 5201
Reverse mode, remote host 192.168.1.4 is sending
[  5] local 192.168.1.1 port 55140 connected to 192.168.1.4 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   1.00-2.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   2.00-3.00   sec   111 MBytes   934 Mbits/sec                  
[  5]   3.00-4.00   sec   112 MBytes   942 Mbits/sec                  
[  5]   4.00-5.00   sec   112 MBytes   942 Mbits/sec                  
[  5]   5.00-6.00   sec   112 MBytes   942 Mbits/sec                  
[  5]   6.00-7.00   sec   112 MBytes   942 Mbits/sec                  
[  5]   7.00-8.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   8.00-9.00   sec   112 MBytes   942 Mbits/sec                  
[  5]   9.00-10.00  sec   112 MBytes   942 Mbits/sec                  
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  1.10 GBytes   943 Mbits/sec    0             sender
[  5]   0.00-10.00  sec  1.10 GBytes   941 Mbits/sec                  receiver

iperf Done.
root@OpenWrt:~#

WiFi 5GHz 160MHz 40 iperf3 local

[SUM]   0.00-10.02  sec  1.94 GBytes  1.66 Gbits/sec                  sender
[SUM]   0.00-10.12  sec  1.93 GBytes  1.64 Gbits/sec                  receiver

Michi · 2024-09-25T13:50:46.716Z

I created my image for the WAX202 locally with imagebuilder and kmod-mt7915-firmware is included, although I did not specify it as an extra package. Did you use the online version of the image builder?

lleachii · 2024-09-25T13:54:25.394Z

Michi:

locally with imagebuilder and kmod-mt7915-firmware is included

Michi:

Did you use the online version of the image builder?

lleachii:

Firmware Selector

por:

(https://firmware-selector.openwrt.org)

jen1:

https://firmware-selector.openwrt.org/?version=23.05.5&target=bcm53xx%2Fgeneric&id=asus_rt-ac88u

Yes, we used the online Firmware Selector site.

I used: https://firmware-selector.openwrt.org/?version=23.05.5&target=ramips%2Fmt7621&id=netgear_wax202

BoxcarFields · 2024-09-25T14:51:14.797Z

Upgraded fine on Intel NUC7CJYH.

reinerotto · 2024-09-25T15:00:08.594Z

Works well on my workhorse WE826T. Heavily customized image (from src) with multiple SSIDs, sqlite3, tc, nft+ipt, custom dnsmasq, custom pdns_recursor, lighttpd, php, lua scripts.

timur.davletshin · 2024-09-25T15:21:46.790Z

Screenshot 2024-09-25 at 18-16-14 router - LuCI

... so 10 hours after update I have about 100 megabytes of traffic. And I just finished downloading ~20GB...

Can anyone confirm it? Xiaomi AX3200, if that's important

AJCxZ0 · 2024-09-25T15:57:02.510Z

TP-LINK Archer C2600 v1 and two Archer A7s updated using Luci from 23.05.4 to 23.05.5 with settings kept, missing packages installed and devices rebooted.

21 hours later all appears to be working normally*.

Thanks again to all who do the work to make this not just possible, but easy.

*[I am above the law.]

WotC · 2024-09-25T15:57:19.613Z

Big thanks for the release!
Works fine on GL-iNet B1300 using attended sysupgrade.
Issues on banana pi r3 using attended sysupgrade (samba4-libs, luci-app-samba4, libjpeg-turbo, luci-app-vnstat2):

{
    "url": "https://sysupgrade.openwrt.org",
    "revision": "r24012-d8dd03c46f",
    "advanced_mode": "1",
    "sha256_unsigned": "",
    "branch": "23.05",
    "efi": null,
    "profile": "bananapi,bpi-r3",
    "target": "mediatek/filogic",
    "version": "23.05.5",
    "packages": [
        "auc",
        "base-files",
        "block-mount",
        "busybox",
        "ca-bundle",
        "cgi-io",
        "collectd",
        "collectd-mod-cpu",
        "collectd-mod-df",
        "collectd-mod-ethstat",
        "collectd-mod-interface",
        "collectd-mod-ipstatistics",
        "collectd-mod-irq",
        "collectd-mod-iwinfo",
        "collectd-mod-load",
        "collectd-mod-memory",
        "collectd-mod-netlink",
        "collectd-mod-network",
        "collectd-mod-rrdtool",
        "collectd-mod-syslog",
        "collectd-mod-thermal",
        "collectd-mod-wireless",
        "dnsmasq",
        "dropbear",
        "e2fsprogs",
        "eip197-mini-firmware",
        "f2fsck",
        "firewall4",
        "fstools",
        "fwtool",
        "getrandom",
        "hostapd-common",
        "iw",
        "iwinfo",
        "jansson",
        "jshn",
        "jsonfilter",
        "kernel",
        "kmod-cfg80211",
        "kmod-crypto-acompress",
        "kmod-crypto-aead",
        "kmod-crypto-authenc",
        "kmod-crypto-ccm",
        "kmod-crypto-cmac",
        "kmod-crypto-crc32c",
        "kmod-crypto-ctr",
        "kmod-crypto-des",
        "kmod-crypto-gcm",
        "kmod-crypto-gf128",
        "kmod-crypto-ghash",
        "kmod-crypto-hash",
        "kmod-crypto-hmac",
        "kmod-crypto-hw-safexcel",
        "kmod-crypto-manager",
        "kmod-crypto-md5",
        "kmod-crypto-null",
        "kmod-crypto-rng",
        "kmod-crypto-seqiv",
        "kmod-crypto-sha1",
        "kmod-crypto-sha256",
        "kmod-crypto-sha512",
        "kmod-fs-ext4",
        "kmod-gpio-button-hotplug",
        "kmod-hwmon-core",
        "kmod-hwmon-pwmfan",
        "kmod-i2c-gpio",
        "kmod-leds-gpio",
        "kmod-lib-crc-ccitt",
        "kmod-lib-crc32c",
        "kmod-lib-lzo",
        "kmod-libphy",
        "kmod-mac80211",
        "kmod-mt76-connac",
        "kmod-mt76-core",
        "kmod-mt7915e",
        "kmod-mt7986-firmware",
        "kmod-nf-conntrack",
        "kmod-nf-conntrack6",
        "kmod-nf-flow",
        "kmod-nf-log",
        "kmod-nf-log6",
        "kmod-nf-nat",
        "kmod-nf-reject",
        "kmod-nf-reject6",
        "kmod-nfnetlink",
        "kmod-nft-core",
        "kmod-nft-fib",
        "kmod-nft-nat",
        "kmod-nft-offload",
        "kmod-phy-aquantia",
        "kmod-ppp",
        "kmod-pppoe",
        "kmod-pppox",
        "kmod-sfp",
        "kmod-slhc",
        "kmod-thermal",
        "kmod-usb-storage",
        "kmod-usb2",
        "kmod-usb3",
        "libblobmsg-json",
        "libc",
        "libiwinfo",
        "libiwinfo-data",
        "libjson-c",
        "libjson-script",
        "liblucihttp",
        "liblucihttp-ucode",
        "libmbedtls",
        "libmnl",
        "libnftnl",
        "libnl-tiny",
        "libubox",
        "libubus",
        "libuci",
        "libuclient",
        "libucode",
        "libustream-mbedtls",
        "logd",
        "luci",
        "luci-app-attendedsysupgrade",
        "luci-app-firewall",
        "luci-app-nlbwmon",
        "luci-app-opkg",
        "luci-app-samba4",
        "luci-app-statistics",
        "luci-app-usteer",
        "luci-app-vnstat2",
        "luci-base",
        "luci-light",
        "luci-mod-admin-full",
        "luci-mod-network",
        "luci-mod-status",
        "luci-mod-system",
        "luci-proto-ipv6",
        "luci-proto-ppp",
        "luci-ssl",
        "luci-theme-bootstrap",
        "mkf2fs",
        "mt7986-wo-firmware",
        "mtd",
        "nano-full",
        "netifd",
        "nftables-json",
        "odhcp6c",
        "odhcpd-ipv6only",
        "openssh-client-utils",
        "openssh-server-pam",
        "openssh-sftp-client",
        "openssh-sftp-server",
        "openwrt-keyring",
        "opkg",
        "parted",
        "ppp",
        "ppp-mod-pppoe",
        "procd",
        "procd-seccomp",
        "procd-ujail",
        "px5g-mbedtls",
        "resize2fs",
        "rpcd",
        "rpcd-mod-file",
        "rpcd-mod-iwinfo",
        "rpcd-mod-luci",
        "rpcd-mod-rrdns",
        "rpcd-mod-ucode",
        "sshpass",
        "ubi-utils",
        "uboot-envtools",
        "ubox",
        "ubus",
        "ubusd",
        "uci",
        "uclient-fetch",
        "ucode",
        "ucode-mod-fs",
        "ucode-mod-html",
        "ucode-mod-math",
        "ucode-mod-ubus",
        "ucode-mod-uci",
        "uhttpd",
        "uhttpd-mod-ubus",
        "urandom-seed",
        "urngd",
        "usign",
        "wireless-regdb",
        "wpad-openssl"
    ],
    "diff_packages": true,
    "filesystem": "squashfs",
    "client": "luci/git-23.339.51123-138595a"
}

STDERR:

Generate local signing keys...
Generate local certificate...
Package list missing or not up-to-date, generating it.

Building package index...
Downloading https://downloads.openwrt.org/releases/23.05.5/targets/mediatek/filogic/packages/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_core
Downloading https://downloads.openwrt.org/releases/23.05.5/targets/mediatek/filogic/packages/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/base/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_base
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/base/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/luci/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_luci
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/luci/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/packages/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_packages
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/packages/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/routing/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_routing
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/routing/Packages.sig
Signature check passed.
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/telephony/Packages.gz
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/openwrt_telephony
Downloading https://downloads.openwrt.org/releases/23.05.5/packages/aarch64_cortex-a53/telephony/Packages.sig
Signature check passed.
Downloading file:packages/Packages
Updated list of available packages in /builder/build_dir/target-aarch64_cortex-a53_musl/root-mediatek/../../../../builder/dl/imagebuilder
Downloading file:packages/Packages.sig
Signature check passed.
Collected errors:
 * opkg_install_pkg: Checksum or size mismatch for package samba4-libs. Either the opkg or the package index are corrupt. Try 'opkg update'.
 * opkg_install_cmd: Cannot install package luci-app-samba4.
 * opkg_install_pkg: Checksum or size mismatch for package libjpeg-turbo. Either the opkg or the package index are corrupt. Try 'opkg update'.
 * opkg_install_cmd: Cannot install package luci-app-vnstat2.
make[2]: *** [Makefile:189: package_install] Error 255
make[1]: *** [Makefile:154: _call_manifest] Error 2
make: *** [Makefile:274: manifest] Error 2

KR

wahflz · 2024-09-25T16:18:03.440Z

I'm not getting 5 Ghz connectivity after upgrading from 23.05.4 on my Netgear R6700 v2 and Linksys E8450. I'm not sure if it's a configuration issue. I'll have to look at my logs when I get time.

XA-Hydra · 2024-09-25T17:32:05.771Z

Did you customize your build with extra packages? The base package list for all models in the firmware selector is missing packages that have always been there before, such as firmware for wireless radios for said devices.

The plain stock builds are working fine.

grauerfuchs · 2024-09-25T17:32:13.091Z

You're not the only one with issues on the MT76* and MT79* hardware. I suspect that there is a new dependency that the custom builder component of the firmware selector doesn't yet know about and so it isn't listed by default. Did you use the default builds or did you customize?

XA-Hydra · 2024-09-25T17:33:11.591Z

It seems to be every device and hardware (firmware missing from custom package firmware builds)? Anybody in the know that can update if this is going to be fixed?

grauerfuchs · 2024-09-25T17:35:07.561Z

I can't confirm whether it's every device or not. The only devices I've had issues upgrading are the MT76* devices which (in my network) all require additional packages. This includes the Ubiquiti U6 Lite, the BPI R3, the Linksys e8450 and others.

XA-Hydra · 2024-09-25T17:36:30.339Z

I've noticed it on both my mediatek and non-mediatek devices