But in 21.02 you also now have DSA for those mvbu Linksys devices so do you have those settings right for the radios?
But fault in DSA config usually is binary, it ether work or don’t work in comparison when the driver fault show up as diffuse faults and stability problems.
1 Like
yeah yeah debugging... you are right though, but in standard Wifi AC 36 channel always working. not it is not stable. on wifi ac 36 channel was always stable.
1 Like
Iam trying to install it to esxi.. But after installiong and starting, LUCI stucks in "Loading View" .. everything else is fine but the interface is not working 
I even can login and then: stuck.. No upgrade.. fresh installed with combine image
yes same here, always stable my wrt 3200 acm, but not on this v21
Nice! waiting for it
Openwrt 21.02.0-rc Modulation problems in TP-LINK EAP225 Outdoor
Analysis could be possible if you would reveal the router device model and provide debug logs.
"See now?!"
I tried the release candidate on an Aruba AP11 (AP-303) and temporarily put it into service as a one-armed router, WLAN AP and IPsec VPN gateway. The firmware image was built with the RC1 Imagebuilder using the following package list modifications:
Packages
ddns-scripts
conntrack
etherwake
ip-full
ipset
iwinfo
tc
kmod-ifb
kmod-sched
kmod-sched-connmark
picocom
hostapd-utils
strongswan-minimal
strongswan-mod-pkcs1
strongswan-mod-gcrypt
strongswan-mod-pem
strongswan-mod-curve25519
strongswan-mod-pkcs8
strongswan-mod-gcm
strongswan-mod-sha2
luci-ssl
luci-app-sqm
kmod-sched-cake
tcpdump
kmod-ipt-raw
kmod-ipt-raw6
nand-utils
ubi-utils
-swconfig
-kmod-usb3
-kmod-usb-dwc3
-kmod-usb-dwc3-qcom
Soon, /overlay turned read-only because of flash access errors.
On a closer look, I found error messages from the ath10k-ct driver shortly before that, like:
Cannot communicate with firmware
I do not know if the errors were related in any way, or this was just a coincidence.
dmesg
[ 106.171469] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
[ 135.847988] ath10k_ahb a800000.wifi: Invalid peer id 1 or peer stats buffer, peer: 694ed8c3 sta: 00000000
[ 3078.245353] ath10k_ahb a800000.wifi: htt tx: fixing invalid VHT TX rate code 0xff
[ 5619.778863] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5619.778909] ath10k_ahb a800000.wifi: received addba event for invalid vdev_id: 1
[ 5619.835223] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5619.923733] ath10k_ahb a800000.wifi: received addba event for invalid vdev_id: 1
[ 5619.991450] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5620.079978] ath10k_ahb a800000.wifi: received addba event for invalid vdev_id: 1
[ 5620.153486] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5620.236745] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5620.320636] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5620.391659] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5620.459157] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5620.530073] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5620.597692] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5620.668618] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5620.736233] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5620.807159] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5620.874782] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5620.946745] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5621.013376] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5621.100913] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5621.188354] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5621.275919] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5621.363362] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5621.450903] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5621.538348] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5621.625895] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5621.713348] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5621.800899] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5621.889676] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5621.975842] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5622.046748] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5622.114390] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5622.185270] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5622.252949] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5622.340406] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5622.411292] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5622.479002] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5622.566447] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5622.637359] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5622.705034] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5622.792489] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5622.863364] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5622.931068] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5623.018535] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5623.089403] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5623.157108] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5623.244569] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5623.315451] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5623.383153] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5623.470613] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5623.541497] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5623.609191] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5623.696658] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5623.767536] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5623.835236] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5623.922692] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5623.993578] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5624.061274] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5624.148734] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5624.219616] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5624.287329] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5624.374805] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5624.445668] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5624.513365] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5624.600821] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5624.671715] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5624.739402] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5624.826859] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5624.897736] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5624.965437] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5624.968045] ath10k_ahb a000000.wifi: Cannot communicate with firmware, previous wmi cmds: 40859:532190 37004:531938 37004:531936 37004:531935, jiffies: 532497, attempting to fake crash and restart firmware, dev-flags: 0x42
[ 5625.052906] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5625.123742] ath10k_ahb a000000.wifi: hif fw_crashed_dump
[ 5625.123752] ath10k_ahb a000000.wifi: failed to send wmi nop: -11
[ 5625.358150] ath10k_ahb a800000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5625.427919] ath10k_ahb a000000.wifi: could not request stats (type -268435456 ret -108 specifier 1)
[ 5625.494609] ath10k_ahb a800000.wifi: No VIF found for vdev 1
[ 5625.759138] ath10k_ahb a800000.wifi: no vif for vdev_id 1 found
[ 5625.833232] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5625.897883] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5625.985236] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5626.072776] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5626.160226] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5626.247756] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5626.317986] qcom-nandc 79b0000.qpic-nand: failure to write page
[ 5626.335218] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5626.422706] ubi0 error: 0xc067d1a8: error -110 while writing 2048 bytes to PEB 87:51200, written 0 bytes
[ 5626.493583] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5626.581039] CPU: 2 PID: 171 Comm: ubifs_bgt0_2 Not tainted 5.4.111 #0
[ 5626.697713] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5626.782035] Hardware name: Generic DT based system
[ 5626.782049] Function entered at [<c030e444>] from [<c030aec4>]
[ 5626.782059] Function entered at [<c030aec4>] from [<c08889c4>]
[ 5626.861318] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5626.946618] Function entered at [<c08889c4>] from [<c067d1ac>]
[ 5626.946624] Function entered at [<c067d1ac>] from [<c067a574>]
[ 5626.946629] Function entered at [<c067a574>] from [<c0678f04>]
[ 5626.946636] Function entered at [<c0678f04>] from [<c04e2618>]
[ 5626.946644] Function entered at [<c04e2618>] from [<c04e3008>]
[ 5627.004994] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5627.074744] Function entered at [<c04e3008>] from [<c04e33cc>]
[ 5627.074749] Function entered at [<c04e33cc>] from [<c04ece9c>]
[ 5627.074755] Function entered at [<c04ece9c>] from [<c033df64>]
[ 5627.074761] Function entered at [<c033df64>] from [<c03010e8>]
[ 5627.074766] Exception stack(0xde5b7fb0 to 0xde5b7ff8)
[ 5627.074775] 7fa0: 00000000 00000000 00000000 00000000
[ 5627.144629] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5627.230999] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5627.231008] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 5627.378007] ath10k_ahb a800000.wifi: failed to synchronize setup for vdev 1: -110
[ 5627.441477] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5627.511232] ath10k_ahb a800000.wifi: failed to stop vdev 1: -110
[ 5627.581108] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5628.621682] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped new beacon
[ 5628.706052] ath10k_ahb a000000.wifi: failed to send wmi nop: -108
[ 5628.706093] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5628.868542] ath10k_ahb a000000.wifi: could not request stats (type -268435456 ret -108 specifier 1)
[ 5628.868548] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5628.868626] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5629.149800] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5629.237361] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5629.267983] qcom-nandc 79b0000.qpic-nand: failure to read page/oob
[ 5629.324807] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
[ 5629.412280] ubi0 error: 0xc0683320: err -110 while reading 2048 bytes from PEB 87:51200, read 0 bytes
[ 5629.412308] ubi0 warning: 0xc067a70c: failed to write data to PEB 87
[ 5629.487336] ath10k_ahb a000000.wifi: SWBA overrun on vdev 1, skipped old beacon
[ 5629.573742] ubi0 warning: 0xc0679b00: switch to read-only mode
[ 5629.686253] ath10k_ahb a000000.wifi: SWBA overrun on vdev 0, skipped old beacon
I rebooted the device to restore write access, and replaced the ath10k driver with the non-ct version, as well as the corresponding firmware, ath10k-firmware-qca4019.
Reboot again, and the device has been running stable now for 27 hours, including WLAN and NAND flash.
RPi4 bcm2711 not there..
- release gets tagged
- release gets built
- release gets announced
'release is out'
5 Likes
probably the bots are crunching the firmwares and packages so wait until they are built and uploaded.
1 Like
Yea I don't encourage people to install rc2 until they release it. I installed rc2 on my WRT32X this morning and it worked great until I noticed Samba4 was broken on LuCI with some "TypeError". I also noticed a couple other odd LuCI errors. rc1 doesn't have those issues.
edit: looks like it was a legit bug and was just fixed, commit link below. That's why we wait 
1 Like
Thx for the heads up. I just checked in after being absent for awhile and I was about to try to put a build together.
I am without vlan setup thru luci until development is further along. Can make a person careless when to eager to update.
one guy temporarily bricked his router and was so frustrated
Learn From Laurence.
it should go without saying that testing "release candidate" and other "request for testing" has risk and the user should already know how to recover...
2 Likes
you would think so, but the gift and curse of enticing the casual to get into this scene is that they don't fully understand these things.
personally speaking i think it's quite a bit to expect the openwrt userbase to know how to solder+serial, but that's just me. this in no way, of course, is a reflection on the users. it's just my assumption.
forum activity is a skewed representation/sampling of this userbase if you ask me.
2 Likes
That is the thing with support forums (regardless of product), it is the user group with some kind of failure that is most commonly found in these forums.
The other big user group that is most often never heard of is the one that makes it work and use it quietly.
And then we have the user group (often somewhat small in size compared to the fault group) that doesn’t have a direct fault but want to grow their know-how in some way.
In the viewpoint of Release Candidates many don’t seem to read “rc1” at all and understand the implication of those letters, they just read 21.02.
3 Likes
This topic was automatically closed 2 days after the last reply. New replies are no longer allowed.