dmesg
0.000000] Linux version 6.6.58 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28003-e99b5832e8) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Sun N
3 19:12:35 2024
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Zyxel LTE5398-M904
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s19104 r8192 d21856 u49152
[ 0.000000] pcpu-alloc: s19104 r8192 d21856 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=0001a050
[ 0.000000] Readback ErrCtl register=0001a050
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 247048K/262144K available (8372K kernel code, 653K rwdata, 1776K rodata, 1284K init, 229K bss, 15096K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000005] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.016100] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.088345] pid_max: default: 32768 minimum: 301
[ 0.106455] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.120878] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.145676] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[ 0.161435] rcu: Hierarchical SRCU implementation.
[ 0.170867] rcu: Max phase no-delay instances is 1000.
[ 0.182168] smp: Bringing up secondary CPUs ...
[ 0.192178] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.192213] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.192229] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.192289] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.251579] Synchronize counters for CPU 1: done.
[ 0.314289] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.314315] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.314329] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.314363] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.373154] Synchronize counters for CPU 2: done.
[ 0.433700] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.433727] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.433741] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.433778] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.492770] Synchronize counters for CPU 3: done.
[ 0.552393] smp: Brought up 1 node, 4 CPUs
[ 0.568295] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.587843] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.605479] pinctrl core: initialized pinctrl subsystem
[ 0.619338] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.631964] thermal_sys: Registered thermal governor 'step_wise'
[ 0.638745] FPU Affinity set after 11720 emulations
[ 0.661436] reg-fixed-voltage regulator: Failed to allocate supply name
[ 0.674552] reg-fixed-voltage: probe of regulator failed with error -12
[ 0.687775] clocksource: Switched to clocksource GIC
[ 0.707669] NET: Registered PF_INET protocol family
[ 0.717587] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.733771] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.750340] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.765678] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.780917] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.795257] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.808893] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.823521] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.836428] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.851303] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.862536] PCI: CLS 0 bytes, default 32
[ 0.874594] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.888641] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.900145] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.925688] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.945098] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.956754] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.968492] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.980384] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.993694] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 1.011151] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 1.027359] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.397757] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.411562] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.421199] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.431129] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.445245] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.457840] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.468650] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.482296] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.494635] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.506509] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.518948] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[ 1.531454] pci 0000:00:00.0: supports D1
[ 1.539323] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.551592] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.563518] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.575916] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff]
[ 1.588438] pci 0000:00:01.0: supports D1
[ 1.596258] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.610444] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.622407] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.634914] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.647291] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.657646] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.669673] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.683160] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.696680] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[ 1.708598] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.722171] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.751942] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.762274] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.774328] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 1.787809] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.800988] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.814063] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.827894] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.841018] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.854852] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.868323] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 1.881809] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 1.895293] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 1.908761] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.920857] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.932960] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.946433] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.956285] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.968374] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.981862] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 1.996379] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.006222] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 2.018318] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.033999] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.059830] printk: console [ttyS0] disabled
[ 2.069300] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[ 2.087344] printk: console [ttyS0] enabled
[ 2.103894] printk: bootconsole [early0] disabled
[ 2.128508] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 2.141276] nand: Macronix MX30LF1G18AC
[ 2.148918] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.164003] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 2.177506] 10 fixed-partitions partitions found on MTD device mt7621-nand
[ 2.191248] Creating 10 MTD partitions on "mt7621-nand":
[ 2.201864] 0x000000000000-0x000000080000 : "Bootloader"
[ 2.218145] 0x000000080000-0x000000100000 : "Config"
[ 2.233146] 0x000000100000-0x000000140000 : "Factory"
[ 2.247053] 0x000000140000-0x000002000000 : "Kernel"
[ 2.474462] 0x000000540000-0x000002000000 : "ubi"
[ 2.673892] 0x000002140000-0x000004000000 : "Kernel2"
[ 2.902592] 0x000004000000-0x000004100000 : "wwan"
[ 2.920930] 0x000004100000-0x000005100000 : "data"
[ 3.044461] 0x000005100000-0x000005200000 : "rom-d"
[ 3.062877] 0x000005200000-0x000005280000 : "reserve"
[ 3.221780] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.246687] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 3.266427] i2c_dev: i2c /dev entries driver
[ 3.279948] NET: Registered PF_INET6 protocol family
[ 3.293174] Segment Routing with IPv6
[ 3.300676] In-situ OAM (IOAM) with IPv6
[ 3.308688] NET: Registered PF_PACKET protocol family
[ 3.318932] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.345383] 8021q: 802.1Q VLAN Support v1.8
[ 3.391252] gpio-export gpio_export: 1 gpio(s) exported
[ 3.402314] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.443967] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 3.459295] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21)
[ 3.480377] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.491310] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=23)
[ 3.519125] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 3.532712] DSA: tree 0 setup
[ 3.541029] UBI: auto-attach mtd4
[ 3.547687] ubi0: attaching mtd4
[ 3.932951] ubi0: scanning is finished
[ 3.953254] ubi0: attached mtd4 (name "ubi", size 26 MiB)
[ 3.964169] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.977881] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.991415] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.005290] ubi0: good PEBs: 214, bad PEBs: 0, corrupted PEBs: 0
[ 4.017265] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.031666] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 657730483
[ 4.049692] ubi0: available PEBs: 0, total reserved PEBs: 214, PEBs reserved for bad PEB handling: 20
[ 4.068105] ubi0: background thread "ubi_bgt0d" started, PID 447
[ 4.070900] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.091178] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.105391] clk: Disabling unused clocks
[ 4.121173] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.141791] Freeing unused kernel image (initmem) memory: 1284K
[ 4.153764] This architecture does not have kernel memory protection.
[ 4.166634] Run /sbin/init as init process
[ 4.174805] with arguments:
[ 4.174815] /sbin/init
[ 4.174822] with environment:
[ 4.174827] HOME=/
[ 4.174833] TERM=linux
[ 4.663412] init: Console is alive
[ 4.670707] init: - watchdog -
[ 5.570377] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.647308] usbcore: registered new interface driver usbfs
[ 5.658584] usbcore: registered new interface driver hub
[ 5.669482] usbcore: registered new device driver usb
[ 5.681514] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 5.722165] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.747467] init: - preinit -
[ 10.197787] random: crng init done
[ 11.049858] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 11.072455] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.072953] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 14.137076] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 15.556548] UBIFS (ubi0:1): default file-system created
[ 15.568003] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 15.579620] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 614
[ 15.670063] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.685718] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.705491] UBIFS (ubi0:1): FS size: 16379904 bytes (15 MiB, 129 LEBs), max 139 LEBs, journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 15.728532] UBIFS (ubi0:1): reserved for root: 773663 bytes (755 KiB)
[ 15.741361] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID BB16AA12-B0A5-4BBC-9BC8-A08CCF43910F, small LPT model
[ 15.766988] mount_root: overlay filesystem has not been fully initialized yet
[ 15.782108] mount_root: switching to ubifs overlay
[ 15.802738] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 15.899250] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 15.921971] procd: - early -
[ 15.928092] procd: - watchdog -
[ 15.988640] platform 1e1c0000.xhci: deferred probe pending
[ 16.559312] procd: - watchdog -
[ 16.566786] procd: - ubus -
[ 16.732562] procd: - init -
[ 17.492049] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.568506] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized.
[ 17.961175] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 18.146838] usbcore: registered new interface driver cdc_wdm
[ 18.159969] Loading modules backported from Linux version v6.11.2-0-g7aa21fec187b
[ 18.175029] Backport generated by backports.git v6.1.110-1-32-gc61f71fe0942
[ 18.216289] usbcore: registered new interface driver usbserial_generic
[ 18.229641] usbserial: USB Serial support registered for generic
[ 18.441092] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 18.452497] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 18.464757] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 18.481018] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 18.492254] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 18.537755] mt7603e 0000:01:00.0: firmware init done
[ 18.643752] urngd: v1.0.2 started.
[ 18.715889] mt7603e 0000:01:00.0: registering led 'mt76-phy0'
[ 18.839736] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.859357] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 18.870844] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
[ 18.896882] mt7615e 0000:02:00.0: registering led 'mt76-phy1'
[ 18.969641] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 18.969732] ieee80211 phy1: copying sband (band 1) due to VHT EXT NSS BW flag
[ 19.081624] PPP generic driver version 2.4.2
[ 19.096329] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 19.096329]
[ 19.115866] NET: Registered PF_PPPOX protocol family
[ 19.130976] usbcore: registered new interface driver qmi_wwan
[ 19.155712] usbcore: registered new interface driver option
[ 19.167258] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.410283] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[ 19.441762] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149
[ 19.780220] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 38.823258] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 38.883776] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 38.900560] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 38.915494] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 38.935675] br-lan: port 1(lan1) entered blocking state
[ 38.946527] br-lan: port 1(lan1) entered disabled state
[ 38.957366] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[ 38.970082] mtk_soc_eth 1e100000.ethernet eth0: entered allmulticast mode
[ 38.986633] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[ 39.039214] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 39.055578] br-lan: port 2(lan2) entered blocking state
[ 39.066464] br-lan: port 2(lan2) entered disabled state
[ 39.077364] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
[ 39.093027] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
[ 41.722849] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 41.728177] br-lan: port 1(lan1) entered blocking state
[ 41.749213] br-lan: port 1(lan1) entered forwarding state