OEM boot log:
CFE version 1.0.38-114.170 for BCM96362 (32bit,SP,BE)
Build Date: Thu Jul 10 11:05:46 CEST 2014 (f.bellintani@quelo)
Copyright (C) 2000-2011 Broadcom Corporation.
NAND flash device: name ST NAND512W3A2CN6, id 0x2076 block 16KB size 65536KB
8367 Force MII
8367 Start rtk_port_phyEnableAll_set
Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-15) : 96362ADVNrtk
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-15) : LE88506
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
Port 4 link UP
Booting from latest image (0xb9f00000) ...
Decompression OK!
Entry at 0x802624b0
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x802624b0
[ 0.000000] Linux version 2.6.30 (f.bellintani@quelo) (gcc version 4.3.3 (GCC) ) #1 SMP PREEMPT Thu Jul 10 11:54:20 CEST 2014
[ 0.000000] BCM Flash API. Flash device is not found.
[ 0.000000] 96362ADVNrtk prom init
[ 0.000000] CPU revision is: 0002a070 (Broadcom4350)
[ 0.000000] DSL SDRAM reserved: 0x100000
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 07f00000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x00007f00
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00007f00
[ 0.000000] On node 0 totalpages: 32512
[ 0.000000] free_area_init_node: node 0, pgdat 802f0dc0, node_mem_map 81000000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 222 pages used for memmap
[ 0.000000] Normal zone: 28194 pages, LIFO batch:7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32258
[ 0.000000] Kernel command line: root=mtd:rootfs_1 rw rootfstype=jffs2 console=ttyS0,115200 init=/sbin/init
[ 0.000000] wait instruction: enabled
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] NR_IRQS:128
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] console [ttyS0] enabled
[ 0.001000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.002000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.003000] Allocating memory for DSP module core and initialization code
[ 0.004000] Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
[ 0.014000] Memory: 125292k/130048k available (2407k kernel code, 4568k reserved, 558k data, 140k init, 0k highmem)
[ 0.015000] Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
[ 0.037000] Mount-cache hash table entries: 512
[ 0.038000] --Kernel Config--
[ 0.039000] SMP=1
[ 0.040000] PREEMPT=1
[ 0.041000] DEBUG_SPINLOCK=0
[ 0.042000] DEBUG_MUTEXES=0
[ 0.043000] Broadcom Logger v0.1 Jul 10 2014 11:47:49
[ 0.046000] CPU revision is: 0002a070 (Broadcom4350)
[ 0.046000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.046000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.046000] Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
[ 0.067000] Brought up 2 CPUs
[ 0.072000] net_namespace: 828 bytes
[ 0.074000] NET: Registered protocol family 16
[ 0.076000] Total Flash size: 0K with -1 sectors
[ 0.410000] registering PCI controller with io_map_base unset
[ 0.411000] registering PCI controller with io_map_base unset
[ 0.419000] bio: create slab <bio-0> at 0
[ 0.421000] usbcore: registered new interface driver usbfs
[ 0.422000] usbcore: registered new interface driver hub
[ 0.423000] usbcore: registered new device driver usb
[ 0.426000] pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff]
[ 0.427000] pci 0000:00:00.0: supports D1 D2
[ 0.428000] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.429000] pci 0000:00:00.0: PME# disabled
[ 0.430000] pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
[ 0.431000] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
[ 0.433000] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.434000] pci 0000:01:00.0: PME# disabled
[ 0.436000] pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
[ 0.437000] pci 0000:01:00.0: IO window: disabled
[ 0.438000] pci 0000:01:00.0: MEM window: disabled
[ 0.439000] pci 0000:01:00.0: PREFETCH window: disabled
[ 0.440000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 0.441000] BLOG Rule v1.0 Initialized
[ 0.442000] Broadcom IQoS v0.1 Jul 10 2014 11:52:02 initialized
[ 0.443000] Broadcom GBPM v0.1 Jul 10 2014 11:52:02 initialized
[ 0.451000] NET: Registered protocol family 8
[ 0.452000] NET: Registered protocol family 20
[ 0.456000] NET: Registered protocol family 2
[ 0.472000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.481000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.488000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.495000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.502000] TCP reno registered
[ 0.509000] NET: Registered protocol family 1
[ 0.516000] JFFS2 version 2.2 (NAND) (ZLIB) (LZMA) (RTIME) (c) 2001-2006 Red Hat, Inc.
[ 0.525000] msgmni has been set to 245
[ 0.533000] io scheduler noop registered (default)
[ 0.543000] PPP generic driver version 2.4.2
[ 0.548000] PPP Deflate Compression module registered
[ 0.553000] PPP BSD Compression module registered
[ 0.558000] NET: Registered protocol family 24
[ 0.563000] bcm963xx_mtd driver v2.0
[ 0.567000] Failed to read image tag from flash
[ 0.571000] >> nand_flash_init - entry
[ 0.575000] Broadcom DSL NAND controller (BrcmNand Controller)
[ 0.582000] -->brcmnand_scan: CS=0, numchips=1, csi=0
[ 0.587000] mtd->oobsize=0, mtd->eccOobSize=0
[ 0.592000] NAND_CS_NAND_XOR=00000000
[ 0.595000] Disabling XOR on CS#0
[ 0.599000] brcmnand_scan: Calling brcmnand_probe for CS=0
[ 0.604000] B4: NandSelect=40000001, nandConfig=04042300, chipSelect=0
[ 0.611000] brcmnand_read_id: CS0: dev_id=20762076
[ 0.616000] After: NandSelect=40000001, nandConfig=04042300
[ 0.622000] Block size=00004000, erase shift=14
[ 0.626000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
[ 0.634000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[ 0.641000] timing1 not adjusted: 5363444f
[ 0.645000] timing2 not adjusted: 00000fc6
[ 0.650000] BrcmNAND mfg 20 76 ST ST_NAND512W3A 64MB on CS0
[ 0.655000]
[ 0.655000] Found NAND on CS0: ACC=f3000000, cfg=04042300, flashId=20762076, tim1=5363444f, tim2=00000fc6
[ 0.667000] BrcmNAND version = 0x0202 64MB @00000000
[ 0.672000] B4: NandSelect=40000001, nandConfig=04042300, chipSelect=0
[ 0.678000] brcmnand_read_id: CS0: dev_id=20762076
[ 0.683000] After: NandSelect=40000001, nandConfig=04042300
[ 0.689000] Found NAND flash on Chip Select 0, chipSize=64MB, usable size=64MB, base=0
[ 0.697000] brcmnand_scan: Done brcmnand_probe
[ 0.702000] brcmnand_scan: B4 nand_select = 40000001
[ 0.707000] brcmnand_scan: After nand_select = 40000001
[ 0.712000] brcmnand_scan 10
[ 0.715000] 200 CS=0, chip->ctrl->CS[0]=0
[ 0.719000] 200 chip->ecclevel=15, acc=f3000000
[ 0.724000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
[ 0.732000] brcmnand_scan 220
[ 0.735000] Brcm NAND controller version = 2.2 NAND flash size 64MB @1c000000
[ 0.742000] brcmnand_scan 230
[ 0.745000] brcmnand_scan 40, mtd->oobsize=16, chip->ecclayout=00000000
[ 0.752000] brcmnand_scan 42, mtd->oobsize=16, chip->ecclevel=15, isMLC=0, chip->cellinfo=0
[ 0.761000] brcmnand_scan: mtd->oobsize=16
[ 0.765000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[ 0.771000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
[ 0.780000] 300 CS=0, chip->ctrl->CS[0]=0
[ 0.784000] 500 chip=87a1ed98, CS=0, chip->ctrl->CS[0]=0
[ 0.789000] -->brcmnand_default_bbt
[ 0.793000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[ 0.799000] Bad block table Bbt0 found at page 0001ffe0, version 0xFF for chip on CS0
[ 0.807000] Bad block table 1tbB found at page 0001ffc0, version 0xFF for chip on CS0
[ 0.816000] rescanning ....
[ 1.682000] ----- Contents of BBT -----
[ 1.686000] ----- END Contents of BBT -----
[ 1.691000] brcmnandCET: Status -> Deferred
[ 1.695000] brcmnand_scan 99
[ 1.698000] Creating 11 MTD partitions on "brcmnand.0":
[ 1.703000] 0x000000000000-0x000000004000 : "CFE"
[ 1.710000] 0x000001f00000-0x000002100000 : "bootfs_1"
[ 1.717000] 0x000002100000-0x000003db0000 : "rootfs_1"
[ 1.726000] mtd: partition "rootfs_1" set to be root filesystem
[ 1.732000] 0x000000004000-0x000000204000 : "bootfs_2"
[ 1.738000] 0x000000204000-0x000001eb4000 : "rootfs_2"
[ 1.747000] 0x000000004000-0x000001eb4000 : "upgrade"
[ 1.756000] 0x000003dd0000-0x000003df0000 : "conf_fs_old"
[ 1.763000] 0x000003db0000-0x000003df0000 : "conf_fs"
[ 1.769000] 0x000003df0000-0x000003e00000 : "conf_factory"
[ 1.776000] 0x000003f00000-0x000004000000 : "bbt"
[ 1.782000] 0x000000000000-0x000004000000 : "flash"
[ 1.794000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.801000] PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
[ 1.807000] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 1.813000] ehci_hcd 0000:00:0a.0: EHCI Host Controller
[ 1.819000] ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
[ 1.827000] ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
[ 1.853000] ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
[ 1.864000] ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, overcurrent ignored
[ 1.872000] usb usb1: configuration #1 chosen from 1 choice
[ 1.878000] hub 1-0:1.0: USB hub found
[ 1.882000] hub 1-0:1.0: 2 ports detected
[ 1.888000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.894000] PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
[ 1.900000] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 1.907000] ohci_hcd 0000:00:09.0: OHCI Host Controller
[ 1.912000] ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
[ 1.920000] ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
[ 1.981000] usb usb2: configuration #1 chosen from 1 choice
[ 1.988000] hub 2-0:1.0: USB hub found
[ 1.991000] hub 2-0:1.0: 2 ports detected
[ 1.997000] brcmboard: brcm_board_init entry
[ 2.001000] kerSysScreenPciDevices: 0x14e4:0x435f:(slot 0) detected
[ 2.008000] kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected
[ 2.014000] kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected
[ 2.021000] kerSysScreenPciDevices: 0x14e4:0x6362:(slot 0) detected
[ 2.027000] SES: Button Interrupt 0x2 is enabled
[ 2.032000] sesBtn_mapIntr: is_sesBtn_irq_shared=0, sesBtn_irq=2
[ 2.038000] SES: LED GPIO 0xc00e is enabled
[ 2.042000] PCIe: No device found - Powering down
[ 2.047000] bcm963xx-flash.0: failed to claim resource 0
[ 2.053000] brcm_board_init: isShared=0, rstToDflt_irq=0
[ 2.058000] Serial: BCM63XX driver $Revision: 3.00 $
[ 2.064000] e[0;33mMagic SysRq enabled (type ^ h for list of supported commands)e[0m
[ 2.072000] ttyS0 at MMIO 0xb0000100 (irq = 11) is a BCM63XX
[ 2.078000] ttyS1 at MMIO 0xb0000120 (irq = 12) is a BCM63XX
[ 2.084000] Total # RxBds=848
[ 2.087000] bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
[ 2.087000]
[ 2.095000] bcmPktDma_init: Broadcom Packet DMA Library initialized
[ 2.101000] bcmxtmrt: Broadcom BCM6362B0 ATM/PTM Network Device v0.3 Jul 10 2014 11:50:11
[ 2.112000] TCP cubic registered
[ 2.116000] Initializing XFRM netlink socket
[ 2.120000] NET: Registered protocol family 17
[ 2.125000] NET: Registered protocol family 15
[ 2.130000] Bridge firewalling registered
[ 2.134000] Ebtables v2.0 registered
[ 2.138000] ebt_time registered
[ 2.141000] ebt_ftos registered
[ 2.144000] ebt_wmm_mark registered
[ 2.148000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 2.155000] All bugs added by David S. Miller <davem@redhat.com>
[ 9.705000] VFS: Mounted root (jffs2 filesystem) on device 31:2.
[ 9.712000] Freeing unused kernel memory: 140k freed
init started: BusyBox v1.17.3 (2014-07-10 11:04:17 CEST)
init: setting virtual memory limit 8388608 -1
Starting /etc/rc.d/S10boot.sh ...
mount usb...
Restore passwd ....
Restore group ....
Thu Jul 10 08:57:05 UTC 2014
Starting /etc/rc.d/S11services.sh ...
Please press Enter to activate this console.
-- e[1;44m Base System Init e[m [e[1;33m12.20e[m]
[e[1;34m*e[m] e[36mStarting Event Controllere[m
[e[1;34m*e[m] e[36mLoading Drivers and Kernel Modulese[m
[e[1;34m*e[m] e[36mStarting Configuration Loade[m
[e[1;34m*e[m] e[36mStarting Configuration Manager (B)e[m
/etc/rc.common: line 1: cm: not found
init read conf_factory
read conf_factory 527
end read conf_factory
checkFactoryData: create /tmp/factory/
tar: invalid tar magic
checkFactoryData: tar failed
checkFactoryData: DEVICE_PATH=/tmp/deviceinfo.xml
<?xml version="1.0" encoding="UTF-8"?>
<object name="Device.X_ADB_FactoryData">
<parameter name="WiFiKeyPassphrase">
<value>xxxxxx</value> (value redacted)
</parameter>
<parameter name="WiFiWEPKey">
<value>xxxxxx</value> (value redacted)
</parameter>
<parameter name="WiFiSSID">
<value>TEO-xxxxxx</value> (value redacted)
</parameter>
<parameter name="SerialNumber">
<value>xxxxxx</value> (value redacted)
</parameter>
<parameter name="BaseMACAddress">
<value>xxxxxx</value> (value redacted)
</parameter>
<parameter name="MaxMACAddress">
<value>32</value>
</parameter>
</object>
- e[33m CM TR-181 readye[m
- e[33m CM TR-98 readye[m
[Configuration Load ready]
[e[1;34m*e[m] e[36mProbing for usb devices...e[m
Epicentro Software Version:
Epicentro Platform Version:
Alignement of Model Name parameter
[ 21.198000] bcmport Link UP 1000 mbps full duplex
[e[1;34m*e[m] e[36mStarting Swap Disk (RAM)e[m
Setting up swapspace version 1, size = 3141632 bytes
UUID=a8944bac-67b8-4ae6-b951-0a97867ec1f4
[Swap Disk (RAM) ready]
[ 25.032000] Adding 3064k swap on /dev/zram0. Priority:-1 extents:1 across:3064k SS
[e[1;34m*e[m] e[36mInterfaceMonitor Inite[m
[e[1;34m*e[m] e[36mStarting Firewalle[m
[ 25.280000] --SMP support
[ 25.283000] wl: dsl_tx_pkt_flush_len=338
[ 25.287000] wl: high_wmark_tot=4775
[ 25.291000] wl: passivemode=1
[ 25.294000] wl: napimode=0
[ 25.297000] wl0: allocskbmode=0 currallocskbsz=0
[ 25.308000] Neither SPROM nor OTP has valid image
[ 25.313000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
[ 25.324000] wl:loading /etc/wlan/bcm6362_map.bin
[ 25.332000] srom rev:8
[ 25.346000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16
[ 25.378000] wl0: pqc 16 - size tot 1368
[ 25.382000] * pkt queue base: 128
[ 25.382000] * data HI watermark: 50
[ 25.382000] * PS queue: 1140
[ 25.403000] wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.3.cpe4.12L07.0
[ 25.412000] dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
[Firewall ready]
[e[1;34m*e[m] e[36mStarting QoSe[m
[QoS ready]
[ 26.062000] Initializing USB Mass Storage driver...
[ 26.068000] usbcore: registered new interface driver usb-storage
[ 26.075000] USB Mass Storage support registered.
-- e[1;44m Prepare Networking e[m [e[1;33m26.08e[m]
- e[33mInit USB Interfacese[m
- e[33mInit Video Bridgese[m
- e[33mInit Bridges (0)e[m
Problem with specified source mac ''.
Problem with specified destination mac ''.
-- e[1;44m Start Networking e[m [e[1;33m26.81e[m]
[e[1;34m*e[m] e[36mStarting DHCP servere[m
[DHCP server ready]
[e[1;34m*e[m] e[36mLAN Ethernet Interfaces - Power UP! (B)e[m
[e[1;34m*e[m] e[36mStarting Filteringe[m
[Filtering ready]
[e[1;34m*e[m] e[36mStarting WatchDoge[m
[e[1;34m*e[m] e[36mStarting NATe[m
[NAT ready]
[e[1;34m*e[m] e[36mStarting Port Mappinge[m
[Port Mapping ready]
-- e[1;44m Start Network Services e[m [e[1;33m27.44e[m]
[e[1;34m*e[m] e[36mStarting Wifi Protected Setup service (B)e[m
[e[1;34m*e[m] e[36mStartup Software Execution Environmentse[m
[e[1;34m*e[m] e[36mStarting VOIP services (B)e[m
-- e[1;44m System Ready e[m [e[1;33m28.38e[m]
Starting /etc/rc.d/S50telnet ...
Starting /etc/rc.d/S60ipsec.sh ...
Starting /etc/rc.d/S70vpn.sh ...
Starting /etc/rc.d/S95done ...
1404982648:685756 : 931 : VOIP BASE - File /etc/voip/numplan.conf not found!
1404982648:689183[ 34.996000] BOS: Enter bosInit
: 936 : STA[ 35.000000] BOS: Exit bosInit
TS - Error con[ 35.005000] endpoint_open COMPLETED
nection to cm wi[ 35.010000] xChange assert pid:939
th UNIX socket
1404982648:690051 : 931 : VOIP BASE - Num media profiles 16 VS num channels 2
[ 36.185000] ******* DSP: Found BCM6362 *******
[ 36.190000] ******* DSP: In PCM Mode *******
[ 36.194000] ******* DSP: PCM running in 16 bit mode *******
[ 36.200000] gInterruptCounter = 0xC23E8940
[ 36.205000] gInterruptErrors = 0xC23E8944
[ 36.210000] gNextRxDesc = 0xC23E8A6C
[ 36.215000] gNextTxDesc = 0xC23E8A68
[ 36.220000] gDectTestMode = 0xc22134bc
[ 36.225000] dectBuffStart = 0xc22134c8
[ 36.230000] gDectRxOutOfSyncCounter = 0xc22134cc
[ 36.236000] gDectTxOutOfSyncCounter = 0xc22134d0
[ 36.241000] 32 ms ECAN tail-length
[ 36.245000] *** gStartRxDesc[0] = 0xA0C00000
[ 36.249000] *** gBufferSizeBytes = 640
[ 36.253000] *** gStartTxDesc[0] = 0xA0C01000
[ 36.257000] halPcmInit 367 nextTxDesc = 0xA0C01000
[ 36.263000] halPcmInit 367 nextTxDesc = 0xA0C01008
[ 36.268000] halPcmInit 371 Ownership for TX desc not set. Use this buffer.
[ 40.861000] boardHalInit completed
[ 40.873000] DSP: Interrupt Ids
[ 40.878000] ---------------
[ 40.881000] InterruptId/Location = 44/HIGH
[ 40.886000]
[ 40.886000] DSP: Interrupt Masks
[ 40.891000] ---------------
[ 40.895000] IrqMask = 0x00000500
[ 40.900000] IrqMaskLow = 0x2000C680
[ 40.906000] IrqMask1 = 0x00000010
[ 40.911000] IrqMaskLow1 = 0x00000008
[ 40.916000]
[ 40.916000] DSP: Interrupt Status
[ 40.922000] -----------------
[ 40.925000] IrqStatus = 0x00000000
[ 40.931000] IrqStatusLow = 0x00000000
[ 40.936000] IrqStatus1 = 0x00000000
[ 40.942000] IrqStatusLow1 = 0x00000000
[ 41.167000] EndpointInit completed
[ 41.171000] dgasp: kerSysRegisterDyingGaspHandler: endpoint registered
[ 41.178000] DoVrgConfigureFH: Min 0 Max 0 line 0
[ 41.184000] DoVrgConfigureFH: Min 0 Max 0 line 1
[ 41.222000] set MinHookFlash value 0
[ 41.226000] set MaxHookFlash value 0
[ 41.230000] set EPPROV_MinDisconnect value 110
[ 41.277000] set MinHookFlash value 0
[ 41.281000] set MaxHookFlash value 0
[ 41.285000] set EPPROV_MinDisconnect value 110
