got my own r9000 yesterday.
@egorenar I can help with testing if you need it.
Anyway, what would be safest way to flash openwrt from original firmware?
1 Like
Hi, nice to hear that more people test it now 
I used TFTP flash, this https://kb.netgear.com/000059634/How-to-upload-firmware-to-a-NETGEAR-router-using-Windows-TFTP but on Linux.
It would be a nice test to attempt OpenWRT flash from original factory. This i didn't test. I didn't bother booting Netgear FW first, just jumped immediately into factory flash mode
1 Like
Perfect, Ill boot it from netgear FW and try to flash openwrt.
I assume I may safely 
use bin/targets/alpine/generic/openwrt-alpine-generic-netgear_r9000-squashfs-factory.img from build procedure described here:
Correct?
Yes, img files are for factory flash.
Very good job Egorenar!
I have compiled your build and for the moment I am pretty happy with it. I hope it will become the official one.
With your build, the R9000 finally got the OS that it deserves 
One first thing that I have noticed is the WAN interface LED is not powered up when Internet connectivity is established and have the following lines that are spamming the System log:
Wireless performance is very good out of the box (only security configured)
daemon.info foolsm[1895]: failed to bind to ping interface device "pppoe-wan", "No such device"
daemon.info foolsm[1895]: failed to bind to ping interface device "eth0.2", "No such device"
1 Like
I can confirm that flashing openwrt img from newest factory firmware works fine!
Proceeding to test radios as my unit may have defective 2.4 WiFi.
1 Like
Can someone share with me full dmesg output after booting?
I'd like to see how atheros pciex is being detected, to rule out defective 2.4GHz radio on my unit.
root@OpenWrt:~# dmesg
...
[ 0.559389] msi override pcie-internal
[ 0.563200] al-pcie soc:pcie-internal: PCI host bridge to bus 0000:00
[ 0.569655] pci_bus 0000:00: root bus resource [mem 0xfe000000-0xfeffffff]
[ 0.576519] pci_bus 0000:00: root bus resource [bus 00]
[ 0.581746] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 0.587965] pci 0000:00:00.0: [1c36:0002] type 00 class 0x020000
[ 0.593986] pci 0000:00:00.0: reg 0x10: [mem 0xfe000000-0xfe01ffff 64bit]
[ 0.600785] pci 0000:00:00.0: reg 0x18: [mem 0xfe020000-0xfe020fff 64bit]
[ 0.607575] pci 0000:00:00.0: reg 0x20: [mem 0xfe024000-0xfe027fff 64bit]
[ 0.614390] pci 0000:00:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.622881] pci 0000:00:00.0: PME# supported from D3hot D3cold
[ 0.628748] pci 0000:00:00.0: reg 0x324: [mem 0x00000000-0x0001ffff 64bit]
[ 0.635612] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x00000000-0x0005ffff 64bit] (contains BAR0 for 3 VFs)
[ 0.645584] pci 0000:00:01.0: [1c36:0001] type 00 class 0x020000
[ 0.651615] pci 0000:00:01.0: reg 0x10: [mem 0xfe040000-0xfe05ffff 64bit]
[ 0.658414] pci 0000:00:01.0: reg 0x18: [mem 0xfe060000-0xfe060fff 64bit]
[ 0.665204] pci 0000:00:01.0: reg 0x20: [mem 0xfe064000-0xfe067fff 64bit]
[ 0.672017] pci 0000:00:01.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.680507] pci 0000:00:01.0: PME# supported from D3hot D3cold
[ 0.686596] pci 0000:00:03.0: [1c36:0001] type 00 class 0x020000
[ 0.692626] pci 0000:00:03.0: reg 0x10: [mem 0xfe080000-0xfe09ffff 64bit]
[ 0.699425] pci 0000:00:03.0: reg 0x18: [mem 0xfe0a0000-0xfe0a0fff 64bit]
[ 0.706215] pci 0000:00:03.0: reg 0x20: [mem 0xfe0a4000-0xfe0a7fff 64bit]
[ 0.713029] pci 0000:00:03.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.721512] pci 0000:00:03.0: PME# supported from D3hot D3cold
[ 0.727502] pci 0000:00:04.0: [1c36:0011] type 00 class 0x100000
[ 0.733530] pci 0000:00:04.0: reg 0x10: [mem 0xfe0c0000-0xfe0dffff 64bit]
[ 0.740339] pci 0000:00:04.0: reg 0x20: [mem 0xfe0e0000-0xfe0e1fff 64bit]
[ 0.747142] pci 0000:00:04.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.755629] pci 0000:00:04.0: PME# supported from D3hot D3cold
[ 0.761494] pci 0000:00:04.0: reg 0x324: [mem 0x00000000-0x0001ffff 64bit]
[ 0.768366] pci 0000:00:04.0: VF(n) BAR0 space: [mem 0x00000000-0x0001ffff 64bit] (contains BAR0 for 1 VFs)
[ 0.778297] pci 0000:00:05.0: [1c36:0021] type 00 class 0x088000
[ 0.784314] pci 0000:00:05.0: reg 0x10: [mem 0xfe100000-0xfe11ffff 64bit]
[ 0.791124] pci 0000:00:05.0: reg 0x20: [mem 0xfe120000-0xfe121fff 64bit]
[ 0.797943] pci 0000:00:05.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.806422] pci 0000:00:05.0: PME# supported from D3hot D3cold
[ 0.812287] pci 0000:00:05.0: reg 0x324: [mem 0x00000000-0x0001ffff 64bit]
[ 0.819159] pci 0000:00:05.0: VF(n) BAR0 space: [mem 0x00000000-0x0001ffff 64bit] (contains BAR0 for 1 VFs)
[ 0.830173] PCI: bus0: Fast back to back transfers disabled
[ 0.835755] pci 0000:00:00.0: BAR 0: assigned [mem 0xfe000000-0xfe01ffff 64bit]
[ 0.843087] pci 0000:00:00.0: BAR 7: assigned [mem 0xfe020000-0xfe07ffff 64bit]
[ 0.850398] pci 0000:00:01.0: BAR 0: assigned [mem 0xfe080000-0xfe09ffff 64bit]
[ 0.857713] pci 0000:00:03.0: BAR 0: assigned [mem 0xfe0a0000-0xfe0bffff 64bit]
[ 0.865019] pci 0000:00:04.0: BAR 0: assigned [mem 0xfe0c0000-0xfe0dffff 64bit]
[ 0.872332] pci 0000:00:04.0: BAR 7: assigned [mem 0xfe0e0000-0xfe0fffff 64bit]
[ 0.879642] pci 0000:00:05.0: BAR 0: assigned [mem 0xfe100000-0xfe11ffff 64bit]
[ 0.886947] pci 0000:00:05.0: BAR 7: assigned [mem 0xfe120000-0xfe13ffff 64bit]
[ 0.894256] pci 0000:00:00.0: BAR 4: assigned [mem 0xfe140000-0xfe143fff 64bit]
[ 0.901570] pci 0000:00:01.0: BAR 4: assigned [mem 0xfe144000-0xfe147fff 64bit]
[ 0.908884] pci 0000:00:03.0: BAR 4: assigned [mem 0xfe148000-0xfe14bfff 64bit]
[ 0.916190] pci 0000:00:04.0: BAR 4: assigned [mem 0xfe14c000-0xfe14dfff 64bit]
[ 0.923511] pci 0000:00:05.0: BAR 4: assigned [mem 0xfe14e000-0xfe14ffff 64bit]
[ 0.930825] pci 0000:00:00.0: BAR 2: assigned [mem 0xfe150000-0xfe150fff 64bit]
[ 0.938140] pci 0000:00:01.0: BAR 2: assigned [mem 0xfe151000-0xfe151fff 64bit]
[ 0.945445] pci 0000:00:03.0: BAR 2: assigned [mem 0xfe152000-0xfe152fff 64bit]
[ 0.953050] PCIe 1: Link up. speed gen2 negotiated width 1
[ 0.958539] al-pcie fd800000.pcie-external0: link up: speed Gen 2 width x1
[ 0.965403] Configuring PCIE for IOCC
[ 0.969068] PCIE_1: snoop mode enable
[ 0.973768] msi override pcie-external0
[ 0.977669] al-pcie fd800000.pcie-external0: PCI host bridge to bus 0001:00
[ 0.984620] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff]
[ 0.990973] pci_bus 0001:00: root bus resource [mem 0xe0010000-0xe7ffffff]
[ 0.997845] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.003360] pci 0001:00:00.0: [1c36:0031] type 01 class 0x060400
[ 1.009387] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 1.015656] pci 0001:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff pref]
[ 1.022409] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.030925] pci 0001:00:00.0: supports D1
[ 1.034929] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 1.041505] PCI: bus0: Fast back to back transfers disabled
[ 1.047073] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.055222] pci 0001:01:00.0: [1b21:1182] type 01 class 0x060400
[ 1.061307] pci 0001:01:00.0: enabling Extended Tags
[ 1.066301] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.074839] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.081731] PCI: bus1: Fast back to back transfers disabled
[ 1.087299] pci 0001:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.095527] pci 0001:02:03.0: [1b21:1182] type 01 class 0x060400
[ 1.101615] pci 0001:02:03.0: enabling Extended Tags
[ 1.106609] pci 0001:02:03.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.115142] pci 0001:02:03.0: PME# supported from D0 D3hot D3cold
[ 1.121533] pci 0001:02:07.0: [1b21:1182] type 01 class 0x060400
[ 1.127622] pci 0001:02:07.0: enabling Extended Tags
[ 1.132617] pci 0001:02:07.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.141149] pci 0001:02:07.0: PME# supported from D0 D3hot D3cold
[ 1.147962] PCI: bus2: Fast back to back transfers disabled
[ 1.153530] pci 0001:02:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.161545] pci 0001:02:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.169713] pci 0001:03:00.0: [168c:0046] type 00 class 0x028000
[ 1.175745] pci 0001:03:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.182632] pci 0001:03:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.191189] pci 0001:03:00.0: PME# supported from D0 D3hot D3cold
[ 1.198086] PCI: bus3: Fast back to back transfers disabled
[ 1.203652] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03
[ 1.210443] pci 0001:04:00.0: [168c:0046] type 00 class 0x028000
[ 1.216475] pci 0001:04:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.223372] pci 0001:04:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.231931] pci 0001:04:00.0: PME# supported from D0 D3hot D3cold
[ 1.238825] PCI: bus4: Fast back to back transfers disabled
[ 1.244392] pci_bus 0001:04: busn_res: [bus 04-ff] end is updated to 04
[ 1.251010] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 04
[ 1.257628] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 04
[ 1.264247] pci 0001:00:00.0: BAR 14: assigned [mem 0xe0200000-0xe05fffff]
[ 1.271120] pci 0001:00:00.0: BAR 0: assigned [mem 0xe0010000-0xe0010fff]
[ 1.277917] pci 0001:00:00.0: BAR 1: assigned [mem 0xe0011000-0xe0011fff pref]
[ 1.285133] pci 0001:01:00.0: BAR 14: assigned [mem 0xe0200000-0xe05fffff]
[ 1.292007] pci 0001:02:03.0: BAR 14: assigned [mem 0xe0200000-0xe03fffff]
[ 1.298880] pci 0001:02:07.0: BAR 14: assigned [mem 0xe0400000-0xe05fffff]
[ 1.305745] pci 0001:03:00.0: BAR 0: assigned [mem 0xe0200000-0xe03fffff 64bit]
[ 1.313065] pci 0001:02:03.0: PCI bridge to [bus 03]
[ 1.318036] pci 0001:02:03.0: bridge window [mem 0xe0200000-0xe03fffff]
[ 1.324824] pci 0001:04:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit]
[ 1.332144] pci 0001:02:07.0: PCI bridge to [bus 04]
[ 1.337106] pci 0001:02:07.0: bridge window [mem 0xe0400000-0xe05fffff]
[ 1.343899] pci 0001:01:00.0: PCI bridge to [bus 02-04]
[ 1.349129] pci 0001:01:00.0: bridge window [mem 0xe0200000-0xe05fffff]
[ 1.355914] pci 0001:00:00.0: PCI bridge to [bus 01-04]
[ 1.361144] pci 0001:00:00.0: bridge window [mem 0xe0200000-0xe05fffff]
[ 1.367949] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.376389] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.384837] pci 0001:02:03.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.393288] pci 0001:03:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.401743] pci 0001:02:07.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.410195] pci 0001:04:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.418912] PCIe 2: Link up. speed gen2 negotiated width 1
[ 1.424390] al-pcie fd820000.pcie-external1: link up: speed Gen 2 width x1
[ 1.431263] Configuring PCIE for IOCC
[ 1.434920] PCIE_2: snoop mode enable
[ 1.439621] msi override pcie-external1
[ 1.443511] al-pcie fd820000.pcie-external1: PCI host bridge to bus 0002:00
[ 1.450473] pci_bus 0002:00: root bus resource [io 0x20000-0x2ffff]
[ 1.456816] pci_bus 0002:00: root bus resource [mem 0xe8010000-0xefffffff]
[ 1.463696] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 1.469219] pci 0002:00:00.0: [1c36:0031] type 01 class 0x060400
[ 1.475237] pci 0002:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 1.481515] pci 0002:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff pref]
[ 1.488268] pci 0002:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.496775] pci 0002:00:00.0: supports D1
[ 1.500788] pci 0002:00:00.0: PME# supported from D0 D1 D3hot
[ 1.507358] PCI: bus0: Fast back to back transfers disabled
[ 1.512936] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.521096] pci 0002:01:00.0: [1b21:1142] type 00 class 0x0c0330
[ 1.527127] pci 0002:01:00.0: reg 0x10: [mem 0xe8000000-0xe8007fff 64bit]
[ 1.534008] pci 0002:01:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 256
[ 1.542551] pci 0002:01:00.0: PME# supported from D3cold
[ 1.548626] PCI: bus1: Fast back to back transfers disabled
[ 1.554191] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.560815] pci 0002:00:00.0: BAR 14: assigned [mem 0xe8100000-0xe81fffff]
[ 1.567689] pci 0002:00:00.0: BAR 0: assigned [mem 0xe8010000-0xe8010fff]
[ 1.574471] pci 0002:00:00.0: BAR 1: assigned [mem 0xe8011000-0xe8011fff pref]
[ 1.581695] pci 0002:01:00.0: BAR 0: assigned [mem 0xe8100000-0xe8107fff 64bit]
[ 1.589014] pci 0002:00:00.0: PCI bridge to [bus 01]
[ 1.593976] pci 0002:00:00.0: bridge window [mem 0xe8100000-0xe81fffff]
[ 1.600783] pci 0002:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.609232] pci 0002:01:00.0: Max Payload Size set to 256/ 512 (was 256), Max Read Rq 256
[ 1.617689] pci 0002:01:00.0: enabling device (0140 -> 0142)
[ 1.623657] PCIe 3: Link up. speed gen2 negotiated width 1
[ 1.629164] al-pcie fd840000.pcie-external2: link up: speed Gen 2 width x1
[ 1.636028] Configuring PCIE for IOCC
[ 1.639694] PCIE_3: snoop mode enable
[ 1.644390] msi override pcie-external2
[ 1.648293] al-pcie fd840000.pcie-external2: PCI host bridge to bus 0003:00
[ 1.655244] pci_bus 0003:00: root bus resource [io 0x30000-0x3ffff]
[ 1.661597] pci_bus 0003:00: root bus resource [mem 0xf0010000-0xf7ffffff]
[ 1.668470] pci_bus 0003:00: root bus resource [bus 00-ff]
[ 1.673986] pci 0003:00:00.0: [1c36:0031] type 01 class 0x060400
[ 1.680020] pci 0003:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 1.686289] pci 0003:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff pref]
[ 1.693043] pci 0003:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.701560] pci 0003:00:00.0: supports D1
[ 1.705565] pci 0003:00:00.0: PME# supported from D0 D1 D3hot
[ 1.712145] PCI: bus0: Fast back to back transfers disabled
[ 1.717723] pci 0003:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.725868] pci 0003:01:00.0: [1ae9:0310] type 00 class 0x028000
[ 1.731906] pci 0003:01:00.0: reg 0x10: [mem 0xf0000000-0xf01fffff 64bit]
[ 1.738773] pci 0003:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
[ 1.748047] PCI: bus1: Fast back to back transfers disabled
[ 1.753613] pci_bus 0003:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.760236] pci 0003:00:00.0: BAR 14: assigned [mem 0xf0200000-0xf03fffff]
[ 1.767101] pci 0003:00:00.0: BAR 0: assigned [mem 0xf0010000-0xf0010fff]
[ 1.773891] pci 0003:00:00.0: BAR 1: assigned [mem 0xf0011000-0xf0011fff pref]
[ 1.781116] pci 0003:01:00.0: BAR 0: assigned [mem 0xf0200000-0xf03fffff 64bit]
[ 1.788434] pci 0003:00:00.0: PCI bridge to [bus 01]
[ 1.793396] pci 0003:00:00.0: bridge window [mem 0xf0200000-0xf03fffff]
[ 1.800209] pci 0003:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.808659] pci 0003:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
[ 1.818010] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 1.827023] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.832874] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.889288] bounce: pool size: 64 pages
[ 1.893821] pl061_gpio fd887000.gpio0: PL061 GPIO chip registered
[ 1.900172] pl061_gpio fd888000.gpio1: PL061 GPIO chip registered
[ 1.906485] pl061_gpio fd889000.gpio2: PL061 GPIO chip registered
[ 1.912801] pl061_gpio fd88a000.gpio3: PL061 GPIO chip registered
[ 1.919126] pl061_gpio fd88b000.gpio4: PL061 GPIO chip registered
[ 1.925435] pl061_gpio fd897000.gpio5: PL061 GPIO chip registered
[ 1.931670] irq: no irq domain found for pcie-legacy-intc !
[ 1.937452] pcieport 0001:00:00.0: PME: Signaling with IRQ 180
[ 1.943528] pcieport 0001:00:00.0: AER: enabled with IRQ 180
[ 1.949441] irq: no irq domain found for pcie-legacy-intc !
[ 1.955015] pcieport 0001:01:00.0: enabling device (0140 -> 0142)
[ 1.961429] irq: no irq domain found for pcie-legacy-intc !
[ 1.967003] pcieport 0001:02:03.0: enabling device (0140 -> 0142)
[ 1.973458] irq: no irq domain found for pcie-legacy-intc !
[ 1.979047] pcieport 0001:02:07.0: enabling device (0140 -> 0142)
[ 1.985500] irq: no irq domain found for pcie-legacy-intc !
[ 1.991264] pcieport 0002:00:00.0: PME: Signaling with IRQ 184
[ 1.997294] pcieport 0002:00:00.0: AER: enabled with IRQ 184
[ 2.003203] irq: no irq domain found for pcie-legacy-intc !
[ 2.008983] pcieport 0003:00:00.0: PME: Signaling with IRQ 185
[ 2.015027] pcieport 0003:00:00.0: AER: enabled with IRQ 185
[ 2.021306] al_dma: Annapurna Labs DMA Driver 0.01
[ 2.026180] al_dma 0000:00:05.0: of_irq_parse_pci: failed with rc=-22
[ 2.148684] al_dma 0000:00:05.0: enabling device (0000 -> 0002)
[ 2.267657] pci 0000:00:05.1: [1c36:8021] type 00 class 0x088000
[ 2.273676] pci 0000:00:05.1: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
[ 2.398656] al_dma 0000:00:05.1: enabling device (0400 -> 0402)
[ 2.405421] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.412589] printk: console [ttyS0] disabled
[ 2.416908] fd883000.uart0: ttyS0 at MMIO 0xfd883000 (irq = 176, base_baud = 23437500) is a 16550A
[ 2.425889] printk: console [ttyS0] enabled
[ 2.434249] printk: bootconsole [ns16550a0] disabled
[ 2.444580] fd884000.uart1: ttyS1 at MMIO 0xfd884000 (irq = 177, base_baud = 23437500) is a 16550A
[ 2.456670] loop: module loaded
[ 2.460059] al_nand_probe: AnnapurnaLabs nand driver
[ 2.465193] annapurna-labs,al-nand fa100000.nand-flash: device_properties: num_col_cyc 2 num_row_cyc 3 pageSize 0
[ 2.475463] annapurna-labs,al-nand fa100000.nand-flash: dev_ext_props: pageSize 2048 blockSize 131072 wordSize 1 eccIsEnabled 1
[ 2.486930] annapurna-labs,al-nand fa100000.nand-flash: ecc_config: algorithm 1 num_corr_bits 0 messageSize 0 spareAreaOffset 2052
[ 2.499781] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xac
[ 2.506126] nand: Macronix MX30UF4G18AB
[ 2.509976] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.517551] annapurna-labs,al-nand fa100000.nand-flash: nand_ecc_config: hw_ecc_enabled 1 oob_size 64 ecc_loc 4
[ 2.527654] Scanning device for bad blocks
[ 2.539465] random: fast init done
[ 2.884059] annapurna-labs,al-nand fa100000.nand-flash: oobavail 2
[ 2.890333] 7 fixed-partitions partitions found on MTD device al-nand
[ 2.896764] Creating 7 MTD partitions on "al-nand":
[ 2.901654] 0x000000000000-0x0000001e0000 : "u-boot"
[ 2.906987] 0x0000001e0000-0x000000300000 : "u-boot-env"
[ 2.912669] 0x000000300000-0x000000440000 : "ART"
[ 2.917719] 0x000000440000-0x000000580000 : "ART.bak"
[ 2.923091] 0x000000580000-0x000002580000 : "kernel"
[ 2.928560] 0x000002580000-0x00001f800000 : "ubi"
[ 2.936229] 0x00001f800000-0x000020000000 : "reserve"
[ 2.943813] libphy: Fixed MDIO Bus: probed
[ 2.949138] libphy: mdio-al-gpio: probed
[ 2.972043] switch0: Atheros AR8337 rev. 2 switch registered on mdio-al-gpio-0
[ 3.647092] al_eth 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
[ 3.653542] al_eth_drv: AnnapurnaLabs unified 1GbE and 10GbE Ethernet Driver al_eth v0.2 (Feb 18, 2013)
[ 3.663034] al_eth 0000:00:00.0: Board info: board type 0 ext phy exists No, ext phy addr 0, mdio freq 2500 Khz, SFP connected Yes, media 5
[ 3.679628] configured MAC to RGMII mode:
[ 3.683635] eth [al_eth_0]: set link speed to 1000Mbps. full duplex.
[ 3.690471] al_eth 0000:00:00.0: MDIO child node missing
[ 3.695780] al_eth 0000:00:00.0 eth0: AnnapurnaLabs unified 1Gbe/10Gbe found at mem fe000000, mac addr 08:36:c9:21:77:0f
[ 3.706752] al_eth 0000:00:01.0: of_irq_parse_pci: failed with rc=-22
[ 3.713288] al_eth 0000:00:01.0: Board info: board type 0 ext phy exists No, ext phy addr 0, mdio freq 2500 Khz, SFP connected No, media 1
[ 3.729786] configured MAC to RGMII mode:
[ 3.733792] eth [al_eth_1]: set link speed to 1000Mbps. full duplex.
[ 3.740903] libphy: mdio-al-eth: probed
[ 3.746590] switch1: Atheros AR8337 rev. 2 switch registered on mdio-al-eth-0
[ 4.285337] al_eth 0000:00:01.0 eth1: AnnapurnaLabs unified 1Gbe/10Gbe found at mem fe080000, mac addr 08:36:c9:21:77:0e
[ 4.296322] al_eth 0000:00:03.0: of_irq_parse_pci: failed with rc=-22
[ 4.302860] al_eth 0000:00:03.0: Board info: board type 0 ext phy exists No, ext phy addr 0, mdio freq 2500 Khz, SFP connected No, media 1
[ 4.319359] configured MAC to RGMII mode:
[ 4.323365] eth [al_eth_2]: set link speed to 1000Mbps. full duplex.
[ 4.330185] al_eth 0000:00:03.0: MDIO child node missing
[ 4.335494] al_eth 0000:00:03.0 eth2: AnnapurnaLabs unified 1Gbe/10Gbe found at mem fe0a0000, mac addr 0a:be:52:c0:7c:ef
[ 4.346506] i2c /dev entries driver
[ 4.351335] al_thermal_probe: Thermal Sensor Loaded at: 0x(ptrval).
[ 4.357851] sp805-wdt fd88c000.wdt0: registration successful
[ 4.364009] sdhci: Secure Digital Host Controller Interface driver
[ 4.370193] sdhci: Copyright(c) Pierre Ossman
[ 4.374545] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.380628] NET: Registered protocol family 10
[ 4.385862] Segment Routing with IPv6
[ 4.389584] NET: Registered protocol family 17
[ 4.394059] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.407135] 8021q: 802.1Q VLAN Support v1.8
[ 4.411376] Registering SWP/SWPB emulation handler
[ 4.423101] ubi0: default fastmap pool size: 185
[ 4.427736] ubi0: default fastmap WL pool size: 92
[ 4.432522] ubi0: attaching mtd5
[ 4.614875] random: crng init done
[ 5.635481] ubi0: scanning is finished
[ 5.648403] ubi0: attached mtd5 (name "ubi", size 466 MiB)
[ 5.653883] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.660764] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.667543] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.674502] ubi0: good PEBs: 3732, bad PEBs: 0, corrupted PEBs: 0
[ 5.680597] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.687818] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1618294608
[ 5.696934] ubi0: available PEBs: 0, total reserved PEBs: 3732, PEBs reserved for bad PEB handling: 80
[ 5.706292] ubi0: background thread "ubi_bgt0d" started, PID 140
[ 5.712936] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.718437] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.729286] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.738885] Freeing unused kernel memory: 1024K
[ 5.757839] Run /sbin/init as init process
[ 5.761937] with arguments:
[ 5.761945] /sbin/init
[ 5.761953] with environment:
[ 5.761961] HOME=/
[ 5.761968] TERM=linux
[ 5.892373] init: Console is alive
[ 5.895878] init: - watchdog -
[ 6.730753] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.759671] raid6: skip pq benchmark and using algorithm neonx8
[ 6.765586] raid6: using neon recovery algorithm
[ 6.770962] xor: measuring software checksum speed
[ 6.780083] arm4regs : 2283 MB/sec
[ 6.788052] 8regs : 2787 MB/sec
[ 6.795827] 32regs : 2873 MB/sec
[ 6.801766] neon : 6247 MB/sec
[ 6.806118] xor: using function: neon (6247 MB/sec)
[ 6.932699] Btrfs loaded, crc32c=crc32c-generic
[ 6.966608] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.978066] SCSI subsystem initialized
[ 6.983509] ehci-fsl: Freescale EHCI Host controller driver
[ 6.991663] ehci-platform: EHCI generic platform driver
[ 7.003453] libata version 3.00 loaded.
[ 7.005512] ehci-pci: EHCI PCI platform driver
[ 7.011232] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.017829] ohci-platform: OHCI generic platform driver
[ 7.023577] ohci-pci: OHCI PCI platform driver
[ 7.036377] irq: no irq domain found for pcie-legacy-intc !
[ 7.042075] xhci_hcd 0002:01:00.0: xHCI Host Controller
[ 7.047315] xhci_hcd 0002:01:00.0: new USB bus registered, assigned bus number 1
[ 7.188793] xhci_hcd 0002:01:00.0: hcc params 0x0200e080 hci version 0x100 quirks 0x0000000010800410
[ 7.199097] hub 1-0:1.0: USB hub found
[ 7.202891] hub 1-0:1.0: 2 ports detected
[ 7.207368] xhci_hcd 0002:01:00.0: xHCI Host Controller
[ 7.212623] xhci_hcd 0002:01:00.0: new USB bus registered, assigned bus number 2
[ 7.220053] xhci_hcd 0002:01:00.0: Host supports USB 3.0 SuperSpeed
[ 7.228123] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.236691] hub 2-0:1.0: USB hub found
[ 7.240492] hub 2-0:1.0: 2 ports detected
[ 7.247467] usbcore: registered new interface driver usb-storage
[ 7.253568] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.266768] init: - preinit -
[ 7.628026] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 7.668585] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 7.675043] scsi host0: usb-storage 2-1:1.0
[ 8.718762] scsi 0:0:0:0: Direct-Access BUFFALO HD-WLU3/R1 1 1.01 PQ: 0 ANSI: 6
[ 8.727944] sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
[ 8.736006] sd 0:0:0:0: [sda] 7812521456 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 8.744520] sd 0:0:0:0: [sda] Write Protect is off
[ 8.749328] sd 0:0:0:0: [sda] Mode Sense: 1f 00 00 08
[ 8.750018] sd 0:0:0:0: [sda] No Caching mode page found
[ 8.755327] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.830398] sda: sda1
[ 8.834745] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.082820] al_eth 0000:00:01.0 eth1: al_eth_open
[ 9.087533] al_eth 0000:00:01.0 eth1: al_eth_open: no phy, use_lm 0
[ 9.093812] al_eth 0000:00:01.0 eth1: al_eth_up
[ 9.098408] configured MAC to RGMII mode:
[ 9.102414] eth [al_eth_1]: set link speed to 1000Mbps. full duplex.
[ 9.109684] al_eth 0000:00:01.0 eth1: using MSI-X per Queue interrupt mode
...
[ 16.394431] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.418288] "cryptomgr_test" (472) uses obsolete ecb(arc4) skcipher
[ 16.431729] al_crypto: Annapurna Labs Crypto Driver 0.01
[ 16.437154] al_crypto 0000:00:04.0: of_irq_parse_pci: failed with rc=-22
[ 16.558697] al_crypto 0000:00:04.0: enabling device (0000 -> 0002)
[ 16.677701] pci 0000:00:04.1: [1c36:8011] type 00 class 0x100000
[ 16.683728] pci 0000:00:04.1: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
...
[ 18.102625] irq: no irq domain found for pcie-legacy-intc !
[ 18.108220] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46.
[ 18.116650] ath10k_pci 0001:03:00.0: enabling device (0140 -> 0142)
[ 18.123357] ath10k_pci 0001:03:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 20.906543] ath10k_pci 0001:03:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 20.916470] ath10k_pci 0001:03:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 20.925489] ath10k_pci 0001:03:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 23.264965] ath10k_pci 0001:03:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[ 26.796225] ath10k_pci 0001:03:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 26.803711] ath10k_pci 0001:03:00.0: msdu-desc: 2500 skid: 32
[ 26.884673] ath10k_pci 0001:03:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 26.895596] ath10k_pci 0001:03:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 27.182640] ath10k_pci 0001:03:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
...
[ 27.283714] irq: no irq domain found for pcie-legacy-intc !
[ 27.289320] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46.
[ 27.297738] ath10k_pci 0001:04:00.0: enabling device (0140 -> 0142)
[ 27.304387] ath10k_pci 0001:04:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 27.632822] ath10k_pci 0001:04:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 27.642748] ath10k_pci 0001:04:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 27.651769] ath10k_pci 0001:04:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 29.988606] ath10k_pci 0001:04:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
[ 33.514220] ath10k_pci 0001:04:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 33.521717] ath10k_pci 0001:04:00.0: msdu-desc: 2500 skid: 32
[ 33.602800] ath10k_pci 0001:04:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 33.613725] ath10k_pci 0001:04:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 33.983020] ath10k_pci 0001:04:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
...
[ 46.959713] ath10k_pci 0001:03:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 46.967194] ath10k_pci 0001:03:00.0: msdu-desc: 2500 skid: 32
[ 47.048086] ath10k_pci 0001:03:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 47.059134] ath10k_pci 0001:03:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 47.442100] ath10k_pci 0001:03:00.0: rts threshold -1
[ 47.447399] ath10k_pci 0001:03:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 47.464286] br-lan: port 2(wlan1) entered blocking state
[ 47.469898] br-lan: port 2(wlan1) entered disabled state
[ 47.475422] device wlan1 entered promiscuous mode
[ 47.644018] ath10k_pci 0001:03:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 110.633438] ath10k_pci 0001:03:00.0: mac flush null vif, drop 0 queues 0xffff
[ 110.655356] br-lan: port 2(wlan1) entered blocking state
[ 110.660677] br-lan: port 2(wlan1) entered forwarding state
[ 306.317903] ath10k_pci 0001:03:00.0: htt tx: fixing invalid VHT TX rate code 0xff
[ 314.618776] ath10k_pci 0001:03:00.0: Invalid VHT mcs 15 peer stats
[139294.608839] ath10k_pci 0001:03:00.0: wmi: fixing invalid VHT TX rate code 0xff
Thanks. Looks one of the atheros radio is not being detected. dmesg below.
I get the unit for $50 after return with '2.4GHz not working' comment. I'm curious however if and how may I debug it further to check what is wrong with 0001:04 atheros.
[ 0.431984] PCI: CLS 0 bytes, default 64
[ 0.448626] msi override pcie-internal
[ 0.452414] al-pcie soc:pcie-internal: PCI host bridge to bus 0000:00
[ 0.458855] pci_bus 0000:00: root bus resource [mem 0xfe000000-0xfeffffff]
[ 0.465720] pci_bus 0000:00: root bus resource [bus 00]
[ 0.470933] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 0.477122] pci 0000:00:00.0: [1c36:0002] type 00 class 0x020000
[ 0.483129] pci 0000:00:00.0: reg 0x10: [mem 0xfe000000-0xfe01ffff 64bit]
[ 0.489905] pci 0000:00:00.0: reg 0x18: [mem 0xfe020000-0xfe020fff 64bit]
[ 0.496686] pci 0000:00:00.0: reg 0x20: [mem 0xfe024000-0xfe027fff 64bit]
[ 0.503475] pci 0000:00:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.511917] pci 0000:00:00.0: PME# supported from D3hot D3cold
[ 0.517754] pci 0000:00:00.0: reg 0x324: [mem 0x00000000-0x0001ffff 64bit]
[ 0.524619] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x00000000-0x0005ffff 64bit] (contains BAR0 for 3 VFs)
[ 0.534497] pci 0000:00:01.0: [1c36:0001] type 00 class 0x020000
[ 0.540497] pci 0000:00:01.0: reg 0x10: [mem 0xfe040000-0xfe05ffff 64bit]
[ 0.547280] pci 0000:00:01.0: reg 0x18: [mem 0xfe060000-0xfe060fff 64bit]
[ 0.554061] pci 0000:00:01.0: reg 0x20: [mem 0xfe064000-0xfe067fff 64bit]
[ 0.560843] pci 0000:00:01.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.569288] pci 0000:00:01.0: PME# supported from D3hot D3cold
[ 0.575285] pci 0000:00:03.0: [1c36:0001] type 00 class 0x020000
[ 0.581286] pci 0000:00:03.0: reg 0x10: [mem 0xfe080000-0xfe09ffff 64bit]
[ 0.588069] pci 0000:00:03.0: reg 0x18: [mem 0xfe0a0000-0xfe0a0fff 64bit]
[ 0.594850] pci 0000:00:03.0: reg 0x20: [mem 0xfe0a4000-0xfe0a7fff 64bit]
[ 0.601631] pci 0000:00:03.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.610072] pci 0000:00:03.0: PME# supported from D3hot D3cold
[ 0.616003] pci 0000:00:04.0: [1c36:0011] type 00 class 0x100000
[ 0.622002] pci 0000:00:04.0: reg 0x10: [mem 0xfe0c0000-0xfe0dffff 64bit]
[ 0.628788] pci 0000:00:04.0: reg 0x20: [mem 0xfe0e0000-0xfe0e1fff 64bit]
[ 0.635574] pci 0000:00:04.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.644016] pci 0000:00:04.0: PME# supported from D3hot D3cold
[ 0.649846] pci 0000:00:04.0: reg 0x324: [mem 0x00000000-0x0001ffff 64bit]
[ 0.656711] pci 0000:00:04.0: VF(n) BAR0 space: [mem 0x00000000-0x0001ffff 64bit] (contains BAR0 for 1 VFs)
[ 0.666554] pci 0000:00:05.0: [1c36:0021] type 00 class 0x088000
[ 0.672553] pci 0000:00:05.0: reg 0x10: [mem 0xfe100000-0xfe11ffff 64bit]
[ 0.679339] pci 0000:00:05.0: reg 0x20: [mem 0xfe120000-0xfe121fff 64bit]
[ 0.686129] pci 0000:00:05.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128
[ 0.694572] pci 0000:00:05.0: PME# supported from D3hot D3cold
[ 0.700401] pci 0000:00:05.0: reg 0x324: [mem 0x00000000-0x0001ffff 64bit]
[ 0.707266] pci 0000:00:05.0: VF(n) BAR0 space: [mem 0x00000000-0x0001ffff 64bit] (contains BAR0 for 1 VFs)
[ 0.718081] PCI: bus0: Fast back to back transfers disabled
[ 0.723657] pci 0000:00:00.0: BAR 0: assigned [mem 0xfe000000-0xfe01ffff 64bit]
[ 0.730953] pci 0000:00:00.0: BAR 7: assigned [mem 0xfe020000-0xfe07ffff 64bit]
[ 0.738251] pci 0000:00:01.0: BAR 0: assigned [mem 0xfe080000-0xfe09ffff 64bit]
[ 0.745551] pci 0000:00:03.0: BAR 0: assigned [mem 0xfe0a0000-0xfe0bffff 64bit]
[ 0.752846] pci 0000:00:04.0: BAR 0: assigned [mem 0xfe0c0000-0xfe0dffff 64bit]
[ 0.760146] pci 0000:00:04.0: BAR 7: assigned [mem 0xfe0e0000-0xfe0fffff 64bit]
[ 0.767445] pci 0000:00:05.0: BAR 0: assigned [mem 0xfe100000-0xfe11ffff 64bit]
[ 0.774744] pci 0000:00:05.0: BAR 7: assigned [mem 0xfe120000-0xfe13ffff 64bit]
[ 0.782037] pci 0000:00:00.0: BAR 4: assigned [mem 0xfe140000-0xfe143fff 64bit]
[ 0.789337] pci 0000:00:01.0: BAR 4: assigned [mem 0xfe144000-0xfe147fff 64bit]
[ 0.796637] pci 0000:00:03.0: BAR 4: assigned [mem 0xfe148000-0xfe14bfff 64bit]
[ 0.803941] pci 0000:00:04.0: BAR 4: assigned [mem 0xfe14c000-0xfe14dfff 64bit]
[ 0.811235] pci 0000:00:05.0: BAR 4: assigned [mem 0xfe14e000-0xfe14ffff 64bit]
[ 0.818535] pci 0000:00:00.0: BAR 2: assigned [mem 0xfe150000-0xfe150fff 64bit]
[ 0.825843] pci 0000:00:01.0: BAR 2: assigned [mem 0xfe151000-0xfe151fff 64bit]
[ 0.833143] pci 0000:00:03.0: BAR 2: assigned [mem 0xfe152000-0xfe152fff 64bit]
[ 0.840559] PCIe 1: Link up. speed gen2 negotiated width 1
[ 0.846040] al-pcie fd800000.pcie-external0: link up: speed Gen 2 width x1
[ 0.852898] Configuring PCIE for IOCC
[ 0.856555] PCIE_1: snoop mode enable
[ 0.861231] msi override pcie-external0
[ 0.865105] al-pcie fd800000.pcie-external0: PCI host bridge to bus 0001:00
[ 0.872051] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff]
[ 0.878396] pci_bus 0001:00: root bus resource [mem 0xe0010000-0xe7ffffff]
[ 0.885260] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.890750] pci 0001:00:00.0: [1c36:0031] type 01 class 0x060400
[ 0.896757] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 0.903014] pci 0001:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff pref]
[ 0.909728] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 0.918188] pci 0001:00:00.0: supports D1
[ 0.922188] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.928547] PCI: bus0: Fast back to back transfers disabled
[ 0.934114] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.942189] pci 0001:01:00.0: [1b21:1182] type 01 class 0x060400
[ 0.948230] pci 0001:01:00.0: enabling Extended Tags
[ 0.953208] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 0.961687] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.968384] PCI: bus1: Fast back to back transfers disabled
[ 0.973952] pci 0001:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.982086] pci 0001:02:03.0: [1b21:1182] type 01 class 0x060400
[ 0.988131] pci 0001:02:03.0: enabling Extended Tags
[ 0.993110] pci 0001:02:03.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.001586] pci 0001:02:03.0: PME# supported from D0 D3hot D3cold
[ 1.007878] pci 0001:02:07.0: [1b21:1182] type 01 class 0x060400
[ 1.013923] pci 0001:02:07.0: enabling Extended Tags
[ 1.018897] pci 0001:02:07.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.027378] pci 0001:02:07.0: PME# supported from D0 D3hot D3cold
[ 1.034002] PCI: bus2: Fast back to back transfers disabled
[ 1.039563] pci 0001:02:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.047572] pci 0001:02:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.055670] pci 0001:03:00.0: [168c:0046] type 00 class 0x028000
[ 1.061686] pci 0001:03:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.068534] pci 0001:03:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.077039] pci 0001:03:00.0: PME# supported from D0 D3hot D3cold
[ 1.083749] PCI: bus3: Fast back to back transfers disabled
[ 1.089310] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03
[ 1.096466] PCI: bus4: Fast back to back transfers enabled
[ 1.101940] pci_bus 0001:04: busn_res: [bus 04-ff] end is updated to 04
[ 1.108547] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 04
[ 1.115153] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 04
[ 1.121762] pci 0001:00:00.0: BAR 14: assigned [mem 0xe0200000-0xe03fffff]
[ 1.128627] pci 0001:00:00.0: BAR 0: assigned [mem 0xe0010000-0xe0010fff]
[ 1.135406] pci 0001:00:00.0: BAR 1: assigned [mem 0xe0011000-0xe0011fff pref]
[ 1.142614] pci 0001:01:00.0: BAR 14: assigned [mem 0xe0200000-0xe03fffff]
[ 1.149479] pci 0001:02:03.0: BAR 14: assigned [mem 0xe0200000-0xe03fffff]
[ 1.156344] pci 0001:03:00.0: BAR 0: assigned [mem 0xe0200000-0xe03fffff 64bit]
[ 1.163655] pci 0001:02:03.0: PCI bridge to [bus 03]
[ 1.168610] pci 0001:02:03.0: bridge window [mem 0xe0200000-0xe03fffff]
[ 1.175392] pci 0001:02:07.0: PCI bridge to [bus 04]
[ 1.180350] pci 0001:01:00.0: PCI bridge to [bus 02-04]
[ 1.185570] pci 0001:01:00.0: bridge window [mem 0xe0200000-0xe03fffff]
[ 1.192345] pci 0001:00:00.0: PCI bridge to [bus 01-04]
[ 1.197565] pci 0001:00:00.0: bridge window [mem 0xe0200000-0xe03fffff]
[ 1.204351] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.212778] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.221212] pci 0001:02:03.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.229649] pci 0001:03:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.238082] pci 0001:02:07.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.246622] PCIe 2: Link up. speed gen2 negotiated width 1
[ 1.252095] al-pcie fd820000.pcie-external1: link up: speed Gen 2 width x1
[ 1.258960] Configuring PCIE for IOCC
[ 1.262613] PCIE_2: snoop mode enable
[ 1.267295] msi override pcie-external1
[ 1.271160] al-pcie fd820000.pcie-external1: PCI host bridge to bus 0002:00
[ 1.278112] pci_bus 0002:00: root bus resource [io 0x20000-0x2ffff]
[ 1.284460] pci_bus 0002:00: root bus resource [mem 0xe8010000-0xefffffff]
[ 1.291319] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 1.296815] pci 0002:00:00.0: [1c36:0031] type 01 class 0x060400
[ 1.302817] pci 0002:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 1.309079] pci 0002:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff pref]
[ 1.315794] pci 0002:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.324254] pci 0002:00:00.0: supports D1
[ 1.328255] pci 0002:00:00.0: PME# supported from D0 D1 D3hot
[ 1.334610] PCI: bus0: Fast back to back transfers disabled
[ 1.340170] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.348265] pci 0002:01:00.0: [1b21:1142] type 00 class 0x0c0330
[ 1.354285] pci 0002:01:00.0: reg 0x10: [mem 0xe8000000-0xe8007fff 64bit]
[ 1.361118] pci 0002:01:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 256
[ 1.369611] pci 0002:01:00.0: PME# supported from D3cold
[ 1.375509] PCI: bus1: Fast back to back transfers disabled
[ 1.381070] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.387681] pci 0002:00:00.0: BAR 14: assigned [mem 0xe8100000-0xe81fffff]
[ 1.394547] pci 0002:00:00.0: BAR 0: assigned [mem 0xe8010000-0xe8010fff]
[ 1.401322] pci 0002:00:00.0: BAR 1: assigned [mem 0xe8011000-0xe8011fff pref]
[ 1.408539] pci 0002:01:00.0: BAR 0: assigned [mem 0xe8100000-0xe8107fff 64bit]
[ 1.415846] pci 0002:00:00.0: PCI bridge to [bus 01]
[ 1.420800] pci 0002:00:00.0: bridge window [mem 0xe8100000-0xe81fffff]
[ 1.427586] pci 0002:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.436021] pci 0002:01:00.0: Max Payload Size set to 256/ 512 (was 256), Max Read Rq 256
[ 1.444459] pci 0002:01:00.0: enabling device (0140 -> 0142)
[ 1.450253] PCIe 3: Link up. speed gen2 negotiated width 1
[ 1.455737] al-pcie fd840000.pcie-external2: link up: speed Gen 2 width x1
[ 1.462597] Configuring PCIE for IOCC
[ 1.466255] PCIE_3: snoop mode enable
[ 1.470934] msi override pcie-external2
[ 1.474806] al-pcie fd840000.pcie-external2: PCI host bridge to bus 0003:00
[ 1.481752] pci_bus 0003:00: root bus resource [io 0x30000-0x3ffff]
[ 1.488097] pci_bus 0003:00: root bus resource [mem 0xf0010000-0xf7ffffff]
[ 1.494961] pci_bus 0003:00: root bus resource [bus 00-ff]
[ 1.500454] pci 0003:00:00.0: [1c36:0031] type 01 class 0x060400
[ 1.506465] pci 0003:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 1.512722] pci 0003:00:00.0: reg 0x14: [mem 0x00000000-0x00000fff pref]
[ 1.519438] pci 0003:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.527900] pci 0003:00:00.0: supports D1
[ 1.531900] pci 0003:00:00.0: PME# supported from D0 D1 D3hot
[ 1.538262] PCI: bus0: Fast back to back transfers disabled
[ 1.543829] pci 0003:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.551903] pci 0003:01:00.0: [1ae9:0310] type 00 class 0x028000
[ 1.557919] pci 0003:01:00.0: reg 0x10: [mem 0xf0000000-0xf01fffff 64bit]
[ 1.564744] pci 0003:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
[ 1.573807] PCI: bus1: Fast back to back transfers disabled
[ 1.579369] pci_bus 0003:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.585980] pci 0003:00:00.0: BAR 14: assigned [mem 0xf0200000-0xf03fffff]
[ 1.592840] pci 0003:00:00.0: BAR 0: assigned [mem 0xf0010000-0xf0010fff]
[ 1.599620] pci 0003:00:00.0: BAR 1: assigned [mem 0xf0011000-0xf0011fff pref]
[ 1.606834] pci 0003:01:00.0: BAR 0: assigned [mem 0xf0200000-0xf03fffff 64bit]
[ 1.614139] pci 0003:00:00.0: PCI bridge to [bus 01]
[ 1.619093] pci 0003:00:00.0: bridge window [mem 0xf0200000-0xf03fffff]
[ 1.625883] pci 0003:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 256
[ 1.634317] pci 0003:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
[ 1.643165] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 1.651538] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.657435] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.706168] bounce: pool size: 64 pages
[ 1.710401] pl061_gpio fd887000.gpio0: PL061 GPIO chip registered
[ 1.716616] pl061_gpio fd888000.gpio1: PL061 GPIO chip registered
[ 1.722806] pl061_gpio fd889000.gpio2: PL061 GPIO chip registered
[ 1.729009] pl061_gpio fd88a000.gpio3: PL061 GPIO chip registered
[ 1.735209] pl061_gpio fd88b000.gpio4: PL061 GPIO chip registered
[ 1.741403] pl061_gpio fd897000.gpio5: PL061 GPIO chip registered
[ 1.747571] irq: no irq domain found for pcie-legacy-intc !
[ 1.753270] pcieport 0001:00:00.0: PME: Signaling with IRQ 180
[ 1.759223] pcieport 0001:00:00.0: AER: enabled with IRQ 180
[ 1.764999] irq: no irq domain found for pcie-legacy-intc !
[ 1.770564] pcieport 0001:01:00.0: enabling device (0140 -> 0142)
[ 1.776831] irq: no irq domain found for pcie-legacy-intc !
[ 1.782396] pcieport 0001:02:03.0: enabling device (0140 -> 0142)
[ 1.788688] irq: no irq domain found for pcie-legacy-intc !
[ 1.794476] irq: no irq domain found for pcie-legacy-intc !
[ 1.800135] pcieport 0002:00:00.0: PME: Signaling with IRQ 184
[ 1.806072] pcieport 0002:00:00.0: AER: enabled with IRQ 184
[ 1.811834] irq: no irq domain found for pcie-legacy-intc !
[ 1.817514] pcieport 0003:00:00.0: PME: Signaling with IRQ 185
[ 1.823490] pcieport 0003:00:00.0: AER: enabled with IRQ 185
[ 1.829427] al_dma: Annapurna Labs DMA Driver 0.01
[ 1.834254] al_dma 0000:00:05.0: of_irq_parse_pci: failed with rc=-22
[ 1.954067] al_dma 0000:00:05.0: enabling device (0000 -> 0002)
[ 2.073069] pci 0000:00:05.1: [1c36:8021] type 00 class 0x088000
[ 2.079071] pci 0000:00:05.1: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128
[ 2.204082] al_dma 0000:00:05.1: enabling device (0400 -> 0402)
[ 2.210529] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.217318] printk: console [ttyS0] disabled
[ 2.221608] fd883000.uart0: ttyS0 at MMIO 0xfd883000 (irq = 176, base_baud = 23437500) is a 16550A
[ 2.230573] printk: console [ttyS0] enabled
[ 2.238922] printk: bootconsole [ns16550a0] disabled
[ 2.249055] fd884000.uart1: ttyS1 at MMIO 0xfd884000 (irq = 177, base_baud = 23437500) is a 16550A
[ 2.260237] loop: module loaded
[ 2.263511] al_nand_probe: AnnapurnaLabs nand driver
[ 2.268560] annapurna-labs,al-nand fa100000.nand-flash: device_properties: num_col_cyc 2 num_row_cyc 3 pageSize 0
[ 2.278809] annapurna-labs,al-nand fa100000.nand-flash: dev_ext_props: pageSize 2048 blockSize 131072 wordSize 1 eccIsEnabled 1
[ 2.290269] annapurna-labs,al-nand fa100000.nand-flash: ecc_config: algorithm 1 num_corr_bits 0 messageSize 0 spareAreaOffset 2052
[ 2.302631] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xac
[ 2.308980] nand: AMD/Spansion S34MS04G2
[ 2.312895] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 2.320561] annapurna-labs,al-nand fa100000.nand-flash: nand_ecc_config: hw_ecc_enabled 1 oob_size 128 ecc_loc 4
[ 2.330729] Scanning device for bad blocks
[ 2.342991] random: fast init done
[ 2.886920] Bad eraseblock 4078 at 0x00001fdc0000
[ 2.891661] Bad eraseblock 4079 at 0x00001fde0000
[ 2.896410] Bad eraseblock 4080 at 0x00001fe00000
[ 2.903124] annapurna-labs,al-nand fa100000.nand-flash: oobavail 2
[ 2.909320] 7 fixed-partitions partitions found on MTD device al-nand
[ 2.915758] Creating 7 MTD partitions on "al-nand":
[ 2.920627] 0x000000000000-0x0000001e0000 : "u-boot"
[ 2.925811] 0x0000001e0000-0x000000300000 : "u-boot-env"
[ 2.931310] 0x000000300000-0x000000440000 : "ART"
[ 2.936228] 0x000000440000-0x000000580000 : "ART.bak"
[ 2.941475] 0x000000580000-0x000002580000 : "kernel"
[ 2.946805] 0x000002580000-0x00001f800000 : "ubi"
[ 2.953963] 0x00001f800000-0x000020000000 : "reserve"
[ 2.960725] libphy: Fixed MDIO Bus: probed
[ 2.965607] libphy: mdio-al-gpio: probed
[ 2.981779] switch0: Atheros AR8337 rev. 2 switch registered on mdio-al-gpio-0
[ 3.597356] al_eth 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
[ 3.603793] al_eth_drv: AnnapurnaLabs unified 1GbE and 10GbE Ethernet Driver al_eth v0.2 (Feb 18, 2013)
[ 3.613226] al_eth 0000:00:00.0: Board info: board type 0 ext phy exists No, ext phy addr 0, mdio freq 2500 Khz, SFP connected Yes, media 5
[ 3.629788] configured MAC to RGMII mode:
[ 3.633796] eth [al_eth_0]: set link speed to 1000Mbps. full duplex.
[ 3.640490] al_eth 0000:00:00.0: MDIO child node missing
[ 3.645804] al_eth 0000:00:00.0 eth0: AnnapurnaLabs unified 1Gbe/10Gbe found at mem fe000000, mac addr 8c:3b:ad:0d:37:b5
[ 3.656707] al_eth 0000:00:01.0: of_irq_parse_pci: failed with rc=-22
[ 3.663188] al_eth 0000:00:01.0: Board info: board type 0 ext phy exists No, ext phy addr 0, mdio freq 2500 Khz, SFP connected No, media 1
[ 3.679663] configured MAC to RGMII mode:
[ 3.683670] eth [al_eth_1]: set link speed to 1000Mbps. full duplex.
[ 3.690545] libphy: mdio-al-eth: probed
[ 3.696045] switch1: Atheros AR8337 rev. 2 switch registered on mdio-al-eth-0
[ 4.240752] al_eth 0000:00:01.0 eth1: AnnapurnaLabs unified 1Gbe/10Gbe found at mem fe080000, mac addr 8c:3b:ad:0d:37:b4
[ 4.251659] al_eth 0000:00:03.0: of_irq_parse_pci: failed with rc=-22
[ 4.258141] al_eth 0000:00:03.0: Board info: board type 0 ext phy exists No, ext phy addr 0, mdio freq 2500 Khz, SFP connected No, media 1
[ 4.274616] configured MAC to RGMII mode:
[ 4.278616] eth [al_eth_2]: set link speed to 1000Mbps. full duplex.
[ 4.285299] al_eth 0000:00:03.0: MDIO child node missing
[ 4.290603] al_eth 0000:00:03.0 eth2: AnnapurnaLabs unified 1Gbe/10Gbe found at mem fe0a0000, mac addr 7e:2c:93:70:dc:8e
[ 4.301535] i2c /dev entries driver
[ 4.306223] al_thermal_probe: Thermal Sensor Loaded at: 0x(ptrval).
[ 4.312618] sp805-wdt fd88c000.wdt0: registration successful
[ 4.318570] sdhci: Secure Digital Host Controller Interface driver
[ 4.324745] sdhci: Copyright(c) Pierre Ossman
[ 4.329091] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.335028] NET: Registered protocol family 10
[ 4.339989] Segment Routing with IPv6
[ 4.343691] NET: Registered protocol family 17
[ 4.348235] 8021q: 802.1Q VLAN Support v1.8
[ 4.352446] Registering SWP/SWPB emulation handler
[ 4.362002] ubi0: default fastmap pool size: 185
[ 4.366632] ubi0: default fastmap WL pool size: 92
[ 4.371412] ubi0: attaching mtd5
[ 4.408769] random: crng init done
[ 5.569971] ubi0: scanning is finished
[ 5.579665] ubi0: attached mtd5 (name "ubi", size 466 MiB)
[ 5.585153] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.592013] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.598794] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.605746] ubi0: good PEBs: 3732, bad PEBs: 0, corrupted PEBs: 0
[ 5.611826] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.619037] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1618756373
[ 5.628156] ubi0: available PEBs: 0, total reserved PEBs: 3732, PEBs reserved for bad PEB handling: 80
[ 5.637500] ubi0: background thread "ubi_bgt0d" started, PID 139
[ 5.644017] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.649492] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.658910] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.666495] Freeing unused kernel memory: 1024K
[ 5.714686] Run /sbin/init as init process
[ 5.718775] with arguments:
[ 5.718780] /sbin/init
[ 5.718784] with environment:
[ 5.718788] HOME=/
[ 5.718792] TERM=linux
[ 5.830768] init: Console is alive
[ 5.834252] init: - watchdog -
[ 6.303576] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.343952] raid6: skip pq benchmark and using algorithm neonx8
[ 6.349863] raid6: using neon recovery algorithm
[ 6.354956] xor: measuring software checksum speed
[ 6.364643] arm4regs : 2011 MB/sec
[ 6.372334] 8regs : 2942 MB/sec
[ 6.381033] 32regs : 2264 MB/sec
[ 6.386930] neon : 6410 MB/sec
[ 6.391276] xor: using function: neon (6410 MB/sec)
<cut>
[ 13.131837] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.181581] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[ 13.189176] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[ 13.200529] xt_time: kernel timezone is -0000
[ 13.228367] PPP generic driver version 2.4.2
[ 13.233147] NET: Registered protocol family 24
[ 13.242467] irq: no irq domain found for pcie-legacy-intc !
[ 13.248060] wil6210 0003:01:00.0: wil6210 device found [1ae9:0310] (rev 2) bar size 0x200000
[ 13.256778] wil6210 0003:01:00.0: enabling device (0140 -> 0142)
[ 13.262800] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_pcie_probe: CSR at [mem 0xf0200000-0xf03fffff 64bit] -> 0x88f6fcff
[ 13.275487] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_set_capabilities: Board hardware is Sparrow B0, flash exist
[ 13.287552] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_set_capabilities: platform_capa 0x0
[ 13.352597] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_refresh_fw_capabilities: keep_radio_on_during_sleep (0)
[ 13.364330] wil6210 0003:01:00.0: using dma mask 48
[ 13.369218] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_if_pcie_enable: 3 MSI mode failed, try 1 MSI
[ 13.473105] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:0b:b6:dc RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 13.489261] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 13.500115] wil6210 0003:01:00.0 (unnamed net_device) (uninitialized): wil_set_oob_mode: oob_mode to 0
[ 13.520274] irq: no irq domain found for pcie-legacy-intc !
[ 13.526463] ath10k_pci 0001:03:00.0: enabling device (0140 -> 0142)
[ 13.533093] ath10k_pci 0001:03:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 14.397355] ath10k_pci 0001:03:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 14.407263] ath10k_pci 0001:03:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 14.416323] ath10k_pci 0001:03:00.0: firmware ver 10.4-3.9.0.2-00131 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate crc32 23bd9e43
[ 16.708581] ath10k_pci 0001:03:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[ 20.456133] ath10k_pci 0001:03:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 20.544573] ath: EEPROM regdomain sanitized
[ 20.544580] ath: EEPROM regdomain: 0x64
[ 20.544584] ath: EEPROM indicates we should expect a direct regpair map
[ 20.544591] ath: Country alpha2 being used: 00
[ 20.544596] ath: Regpair used: 0x64
[ 20.547422] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 23.145693] al_eth 0000:00:01.0 eth1: al_eth_open
[ 23.150406] al_eth 0000:00:01.0 eth1: al_eth_open: no phy, use_lm 0
[ 23.156732] al_eth 0000:00:01.0 eth1: al_eth_up
[ 23.161321] configured MAC to RGMII mode:
[ 23.165346] eth [al_eth_1]: set link speed to 1000Mbps. full duplex.
[ 23.172301] al_eth 0000:00:01.0 eth1: using MSI-X per Queue interrupt mode
[ 23.180047] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 23.187927] br-lan: port 1(eth1.1) entered blocking state
[ 23.193354] br-lan: port 1(eth1.1) entered disabled state
[ 23.198913] device eth1.1 entered promiscuous mode
[ 23.203714] device eth1 entered promiscuous mode
[ 23.209676] br-lan: port 1(eth1.1) entered blocking state
[ 23.215082] br-lan: port 1(eth1.1) entered forwarding state
[ 23.464685] wil6210 0003:01:00.0 wlan0: wil_cfg80211_del_iface: cannot remove the main interface
[ 24.233287] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 24.588026] wil6210 0003:01:00.0 wlan0: wil_cfg80211_add_iface: virtual interfaces not supported
[ 24.607580] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=(null), reason=3
[ 24.616209] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=(null), reason=3
[ 24.673171] wil6210 0003:01:00.0 wlan0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:0b:b6:dc RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 24.686632] wil6210 0003:01:00.0 wlan0: wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 24.694805] wil6210 0003:01:00.0 wlan0: wil_set_oob_mode: oob_mode to 0
[ 24.701408] wil6210 0003:01:00.0 wlan0: wil_reset: Use firmware <wil6210.fw> + board <wil6210.brd>
[ 24.907913] wil6210 0003:01:00.0 wlan0: wmi_evt_ready: FW ver. 5.2.0.18(SW 18); MAC 04:ce:14:0b:b6:dc; 0 MID's
[ 24.917972] wil6210 0003:01:00.0 wlan0: wil_wait_for_fw_ready: FW ready after 180 ms. HW version 0x00000001
[ 24.927887] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_TX_CNT_TRSH = 500 usec
[ 24.937540] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_TX_IDL_CNT_TRSH = 13 usec
[ 24.947446] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_RX_CNT_TRSH = 500 usec
[ 24.957092] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_RX_IDL_CNT_TRSH = 13 usec
[ 24.966997] wil6210 0003:01:00.0 wlan0: wil_refresh_fw_capabilities: keep_radio_on_during_sleep (0)
[ 24.978812] br-lan: port 2(wlan0) entered blocking state
[ 24.984164] br-lan: port 2(wlan0) entered disabled state
[ 24.989675] device wlan0 entered promiscuous mode
[ 24.994565] br-lan: port 2(wlan0) entered blocking state
[ 24.999961] br-lan: port 2(wlan0) entered forwarding state
[ 31.155817] ath10k_pci 0001:03:00.0: Unknown eventid: 36933
[ 31.164853] br-lan: port 3(wlan1) entered blocking state
[ 31.170164] br-lan: port 3(wlan1) entered disabled state
[ 31.175743] device wlan1 entered promiscuous mode
[ 31.181046] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=(null), reason=2
[ 31.189675] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=(null), reason=2
[ 31.200226] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=(null), reason=3
[ 31.208841] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=(null), reason=3
[ 31.313830] wil6210 0003:01:00.0 wlan0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:0b:b6:dc RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 31.327291] wil6210 0003:01:00.0 wlan0: wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 31.335467] wil6210 0003:01:00.0 wlan0: wil_set_oob_mode: oob_mode to 0
[ 31.342073] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=(null), reason=3
[ 31.350680] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=(null), reason=3
[ 31.443152] wil6210 0003:01:00.0 wlan0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:0b:b6:dc RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 31.456608] wil6210 0003:01:00.0 wlan0: wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 31.464780] wil6210 0003:01:00.0 wlan0: wil_set_oob_mode: oob_mode to 0
[ 31.471383] wil6210 0003:01:00.0 wlan0: wil_reset: Use firmware <wil6210.fw> + board <wil6210.brd>
[ 31.504497] wil6210 0003:01:00.0 wlan0: wmi_evt_ready: FW ver. 5.2.0.18(SW 18); MAC 04:ce:14:0b:b6:dc; 0 MID's
[ 31.514536] wil6210 0003:01:00.0 wlan0: wil_wait_for_fw_ready: FW ready after 20 ms. HW version 0x00000001
[ 31.524362] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_TX_CNT_TRSH = 500 usec
[ 31.534011] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_TX_IDL_CNT_TRSH = 13 usec
[ 31.543916] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_RX_CNT_TRSH = 500 usec
[ 31.553559] wil6210 0003:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_RX_IDL_CNT_TRSH = 13 usec
[ 31.563467] wil6210 0003:01:00.0 wlan0: wil_refresh_fw_capabilities: keep_radio_on_during_sleep (0)
[ 31.573805] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=ff:ff:ff:ff:ff:ff, reason=2
[ 31.583367] wil6210 0003:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=ff:ff:ff:ff:ff:ff, reason=2
[ 40.230206] net_ratelimit: 2 callbacks suppressed
[ 52.399433] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 52.405889] br-lan: port 3(wlan1) entered blocking state
[ 52.411194] br-lan: port 3(wlan1) entered forwarding state
[ 56.231408] net_ratelimit: 1 callbacks suppressed
This is lspci output.
root@OpenWrt:~# lspci -k
00:05.1 Class 0880: 1c36:8021 al_dma
00:00.0 Class 0200: 1c36:0002 al_eth
00:03.0 Class 0200: 1c36:0001 al_eth
02:03.0 Class 0604: 1b21:1182 pcieport
01:00.0 Class 0604: 1b21:1182 pcieport
00:00.0 Class 0604: 1c36:0031 pcieport
01:00.0 Class 0c03: 1b21:1142 xhci_hcd
00:05.0 Class 0880: 1c36:0021 al_dma
00:00.0 Class 0604: 1c36:0031 pcieport
00:01.0 Class 0200: 1c36:0001 al_eth
01:00.0 Class 0280: 1ae9:0310 wil6210
00:04.0 Class 1000: 1c36:0011
03:00.0 Class 0280: 168c:0046 ath10k_pci
02:07.0 Class 0604: 1b21:1182 pcieport
00:00.0 Class 0604: 1c36:0031 pcieport
root@OpenWrt:~# lspci -k
0000:00:00.0 Ethernet controller: Annapurna Labs Ltd. SFP+ 10G Ethernet Adapter (rev 01)
Kernel driver in use: al_eth
lspci: Unable to load libkmod resources: error -12
0000:00:01.0 Ethernet controller: Annapurna Labs Ltd. Gigabit Ethernet Adapter (rev 01)
Kernel driver in use: al_eth
0000:00:03.0 Ethernet controller: Annapurna Labs Ltd. Gigabit Ethernet Adapter (rev 01)
Kernel driver in use: al_eth
0000:00:04.0 Network and computing encryption device: Annapurna Labs Ltd. Device 0011 (rev 01)
Kernel driver in use: al_crypto
0000:00:04.1 Network and computing encryption device: Annapurna Labs Ltd. Device 8011 (rev 01)
Kernel driver in use: al_crypto
0000:00:05.0 System peripheral: Annapurna Labs Ltd. Device 0021 (rev 01)
Kernel driver in use: al_dma
0000:00:05.1 System peripheral: Annapurna Labs Ltd. Device 8021 (rev 01)
Kernel driver in use: al_dma
0001:00:00.0 PCI bridge: Annapurna Labs Ltd. Device 0031 (rev 01)
Kernel driver in use: pcieport
0001:01:00.0 PCI bridge: ASMedia Technology Inc. Device 1182
Kernel driver in use: pcieport
0001:02:03.0 PCI bridge: ASMedia Technology Inc. Device 1182
Kernel driver in use: pcieport
0001:02:07.0 PCI bridge: ASMedia Technology Inc. Device 1182
Kernel driver in use: pcieport
0001:03:00.0 Network controller: Qualcomm Atheros QCA9984 802.11ac Wave 2 Wireless Network Adapter
Subsystem: Qualcomm Atheros Device cafe
Kernel driver in use: ath10k_pci
0001:04:00.0 Network controller: Qualcomm Atheros QCA9984 802.11ac Wave 2 Wireless Network Adapter
Subsystem: Qualcomm Atheros Device cafe
Kernel driver in use: ath10k_pci
0002:00:00.0 PCI bridge: Annapurna Labs Ltd. Device 0031 (rev 01)
Kernel driver in use: pcieport
0002:01:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller
Subsystem: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller
Kernel driver in use: xhci_hcd
0003:00:00.0 PCI bridge: Annapurna Labs Ltd. Device 0031 (rev 01)
Kernel driver in use: pcieport
0003:01:00.0 Network controller: Wilocity Ltd. Wil6200 802.11ad Wireless Network Adapter (rev 02)
Subsystem: Wilocity Ltd. Device 0000
Kernel driver in use: wil6210
You could try to enable debug_mask in ath10k driver and reload the driver.
https://wireless.wiki.kernel.org/en/users/Drivers/ath10k/debug
NB: My 2.4 device is completely unused, to many BSSs, 5GHz is much better.
2 Likes
Yeah. I dont plan to use 2.4G, too crowded. I use this device only as learning platform and getting more into openwrt.
Thank you for debug hints, will play with this over weekend and report back.
In the meantime I see that you have more devices detected, did you add (and commited to your branch?) some new things recently?
No, nothing new. The last thing i worked on was the crypto driver. I still need to implement AEAD mode, oddly, the DDWRT fw removed support for AEAD from the crypto driver but the original one from Netgear has it enabled.
1 Like
I have been running the egorenar build on my R9000, with the most recent one being based on r17026+40-277248b293. It's been running pretty smoothly thus far - my only complaint was just that the switch/VLAN settings seem crazy... but I figured it out eventually.
Just out of curiosity - what kind of speeds are you guys getting? I've got basically a Gigabit connection (968 Mbps provisioned speeds), and it's basically like ... hard-wired, I can get very near that speed (930-950) but wireless I seem to be maxing out near 500 Mbps (80 Mhz, channel 149).
Default VLAN settings should work w/o any changes.
My WLAN speed (5GHz Ch 100):
$ iperf3 -c 192.168.1.1 -f g
Connecting to host 192.168.1.1, port 5201
[ 5] local 192.168.1.155 port 37416 connected to 192.168.1.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 45.1 MBytes 0.38 Gbits/sec 0 5.49 MBytes
[ 5] 1.00-2.00 sec 46.2 MBytes 0.39 Gbits/sec 0 5.49 MBytes
[ 5] 2.00-3.00 sec 43.8 MBytes 0.37 Gbits/sec 0 5.49 MBytes
[ 5] 3.00-4.00 sec 45.0 MBytes 0.38 Gbits/sec 0 5.49 MBytes
[ 5] 4.00-5.00 sec 46.2 MBytes 0.39 Gbits/sec 0 5.49 MBytes
[ 5] 5.00-6.00 sec 45.0 MBytes 0.38 Gbits/sec 0 5.49 MBytes
[ 5] 6.00-7.00 sec 45.0 MBytes 0.38 Gbits/sec 0 5.49 MBytes
[ 5] 7.00-8.00 sec 42.5 MBytes 0.36 Gbits/sec 0 5.49 MBytes
[ 5] 8.00-9.00 sec 45.0 MBytes 0.38 Gbits/sec 0 5.49 MBytes
[ 5] 9.00-10.00 sec 47.5 MBytes 0.40 Gbits/sec 0 5.49 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 451 MBytes 0.38 Gbits/sec 0 sender
[ 5] 0.00-10.03 sec 449 MBytes 0.38 Gbits/sec receiver
iperf Done.
It's normal that WLAN is much less than Ethernet, it has a lot of overhead and interference in comparison to Ethernet, it won't ever be close to it.
Congratulations for your success with Netgear devices.
When we can expect stable or test installation image for R9000?
Is R9000 hardware capable to run something like pi-hole?
There's adblock in openwrt, people don't usually put piholes on their routers.
one of the few (beefy) all-in-one 'current-gen' devices that is actually locally obtainable in the AU
- r7800 scarce/prev-gen
- nbg6817 few ever sold / scarce/prev-gen
- synology rt2600ac (nsupp / prev-gen)
- a few ubiquiti/tplink which are on the lower end of beefy or not so fully featured or easiliy flashable
i'm half way through my current AP life cycle and the cost is prohibitive otherwise i'd pick one up...
( $500AU / ~350US is a tad on the high end tho' )
1 Like
Hello! I finally received my R9000 and installed openwrt on it - works great!
A few questions:
- How do I control the fans? I see that it has an i2c fan controller - anything else I can get out of it?
- How do I use the onboard Bluetooth? My unit still has the bluetooth circuit near the A4 antenna connector.
- I can't seem to get any LED other than power to work
Please send me info compile openwrt. No download git link egonear and my ubuntu no comend
git switch