@Ansuel , @quarky , @hnyman
I'm currently testing a NSS master build compiled by me based on Master acwififdude's 15 commits + @rickkz0r 's 13 commits with sqm nss script master/Kernel5.15. After approx. 30 hours I had a crash probably connected to the NSS firmware. Maybe it's not the cache scaling issue.
Panic#1 Part1
<6>[ 7.897397] (unnamed net_device) (uninitialized): nss_gmac_clk_ctl_dev_init: ctx->clk_ctl_base(0xde880000) + CLK_HALT_NSSFAB0_NSSFAB1_STATEA(0x3c20): 0x5b00
<6>[ 7.910775] (unnamed net_device) (uninitialized): nss_gmac_clk_ctl_dev_init: ctx->clk_ctl_base(0xde880000) + GMAC_COREn_CLK_CTL(2)(0x3cf4): 0x50
<6>[ 7.924834] (unnamed net_device) (uninitialized): nss_gmac_dev_init: nss_base(0xde960000) + NSS_GMACn_CTL(2)(0x38): 0x80c0c
<6>[ 7.937759] (unnamed net_device) (uninitialized): nss_gmac_dev_init: nss_base(0xde960000) + NSS_ETH_CLK_DIV0(0xc): 0x100
<6>[ 7.948600] (unnamed net_device) (uninitialized): nss_gmac_qsgmii_dev_init: QSGMII_PHY_SGMII_1_CTL(0x13c) - 0xc09c408f
<6>[ 7.959721] (unnamed net_device) (uninitialized): nss_gmac_qsgmii_dev_init: NSS_QSGMII_CLK_CTL(0x2c) - 0x0
<6>[ 7.970217] (unnamed net_device) (uninitialized): SGMII Specific Init for GMAC2 Done!
<6>[ 7.979889] (unnamed net_device) (uninitialized): ioremap OK. Size 0x4000. reg_base 0x37400000. mac_base 0x7bd0fd7a.
<6>[ 7.987817] (unnamed net_device) (uninitialized): mdio bus '37000000.mdio-mii' OK.
<6>[ 8.005838] ipq8064-mdio 37000000.mdio (unnamed net_device) (uninitialized): nss_gmac_ipc_offload_init: enable Rx checksum
<6>[ 8.006392] ipq8064-mdio 37000000.mdio eth1: Initialized NSS GMAC2 interface eth1: (base = 0x37400000, irq = 40, PhyId = 0, PollLink = 0)
<1>[ 8.102562] nss_driver - fw of size 544712 bytes copied to load addr: 40000000, nss_id : 0
<1>[ 8.103254] nss_driver - Turbo Support 1
<1>[ 8.109805] Supported Frequencies -
<1>[ 8.109811] 800Mhz
<1>[ 8.113891] 800Mhz
<1>[ 8.117513] 800Mhz
<1>[ 8.119271]
<1>[ 8.123696] bf281400: meminfo init succeed
<3>[ 8.125228] (unnamed net_device) (dummy): netif_napi_add() called with weight 64
<1>[ 8.150868] node size 1 # items 2
<1>[ 8.150897] memory: 0 0 (avl 496586752) items 2 active_cores 2
<1>[ 8.153181] addr/size storage words 1 1 # words 2 in DTS, ddr size 1000000
<1>[ 8.158980] bf281400: nss core 0 booted successfully
<1>[ 8.186258] nss_driver - fw of size 218860 bytes copied to load addr: 40800000, nss_id : 1
<1>[ 8.187487] bf285b00: meminfo init succeed
<3>[ 8.193611] debugfs: Directory 'dynamic_if' with parent 'stats' already present!
<3>[ 8.197754] debugfs: File 'n2h' in directory 'strings' already present!
<3>[ 8.205184] debugfs: File 'drv' in directory 'strings' already present!
<1>[ 8.214335] node size 1 # items 2
<6>[ 8.214445] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<1>[ 8.218116] memory: 0 0 (avl 496721920) items 2 active_cores 2
<1>[ 8.218179] addr/size storage words 1 1 # words 2 in DTS, ddr size 1000000
<1>[ 8.218206] bf285b00: nss core 1 booted successfully
<5>[ 8.245916] SCSI subsystem initialized
<7>[ 8.251348] libata version 3.00 loaded.
<4>[ 8.254173] ahci 29000000.sata: supply ahci not found, using dummy regulator
<4>[ 8.254361] ahci 29000000.sata: supply phy not found, using dummy regulator
<4>[ 8.260538] ahci 29000000.sata: supply target not found, using dummy regulator
<6>[ 8.267918] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
<6>[ 8.274297] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
<6>[ 8.279821] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
<6>[ 8.289203] scsi host0: ahci
<6>[ 8.296879] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 32
<6>[ 8.628366] ata1: SATA link down (SStatus 0 SControl 300)
<6>[ 8.633340] fsl-ehci: Freescale EHCI Host controller driver
<6>[ 8.634933] ehci-platform: EHCI generic platform driver
<6>[ 8.649025] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>[ 8.650575] ohci-platform: OHCI generic platform driver
<6>[ 8.795032] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
<6>[ 8.795113] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
<6>[ 8.799747] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
<6>[ 8.807157] xhci-hcd xhci-hcd.0.auto: irq 55, io mem 0x10000000
<6>[ 8.816721] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
<6>[ 8.822268] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
<6>[ 8.827892] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
<6>[ 8.836733] hub 1-0:1.0: USB hub found
<6>[ 8.842139] hub 1-0:1.0: 1 port detected
<6>[ 8.846765] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
<6>[ 8.850302] hub 2-0:1.0: USB hub found
<6>[ 8.857987] hub 2-0:1.0: 1 port detected
<6>[ 8.861961] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
<6>[ 8.865538] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
<6>[ 8.871027] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
<6>[ 8.878435] xhci-hcd xhci-hcd.1.auto: irq 56, io mem 0x11000000
<6>[ 8.887988] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
<6>[ 8.893616] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
<6>[ 8.899240] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
<6>[ 8.907585] hub 3-0:1.0: USB hub found
<6>[ 8.913384] hub 3-0:1.0: 1 port detected
<6>[ 8.917533] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
<6>[ 8.921638] hub 4-0:1.0: USB hub found
<6>[ 8.929682] hub 4-0:1.0: 1 port detected
<6>[ 8.937574] usbcore: registered new interface driver usb-storage
<6>[ 8.938844] usbcore: registered new interface driver uas
<14>[ 8.943087] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
<14>[ 8.956666] init: - preinit -
<6>[ 12.032172] ipq8064-mdio 37000000.mdio eth1: nss_gmac_start_up: Force link up
<6>[ 12.032229] ipq8064-mdio 37000000.mdio eth1: 1000 Mbps Full Duplex
<6>[ 12.038398] ipq8064-mdio 37000000.mdio eth1: nss_gmac_dev_set_speed:NSS_ETH_CLK_DIV0(0xc) - 0x100
<6>[ 12.044386] ipq8064-mdio 37000000.mdio eth1: nss_gmac_dev_set_speed: qsgmii_base(0xde980000) + PCS_MODE_CTL(0x68): 0x80008082
<6>[ 12.053432] ipq8064-mdio 37000000.mdio eth1: nss_gmac_reset: eth1 resetting...
<6>[ 13.119105] ipq8064-mdio 37000000.mdio eth1: GMAC reset completed in 106 jiffies; dma_bus_mode - 0x20100
<6>[ 13.119520] ipq8064-mdio 37000000.mdio eth1: nss_gmac_change_mtu: Enabling Normal Frame MTU (Requested MTU [1500])
<6>[ 13.127790] ipq8064-mdio 37000000.mdio eth1: nss_gmac_change_mtu: Enabling Jumbo Frame MTU for eth1 (Requested MTU [1500])
<6>[ 13.137917] ipq8064-mdio 37000000.mdio eth1: Set addr a0:04:60:09:e4:13
<6>[ 13.148942] ipq8064-mdio 37000000.mdio eth1: nss_gmac_ipc_offload_init: enable Rx checksum
<6>[ 13.155377] ipq8064-mdio 37000000.mdio eth1: nss_gmac_config_flow_control:
<6>[ 13.163780] ipq8064-mdio 37000000.mdio eth1: nss_gmac_rx_pause_disable: disable Rx flow control
<6>[ 13.170653] ipq8064-mdio 37000000.mdio eth1: nss_gmac_tx_pause_disable: disable Tx flow control
<6>[ 13.179623] ipq8064-mdio 37000000.mdio eth1: nss_gmac_linkup: data plane open command successfully issued
<6>[ 13.189168] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
<6>[ 13.198153] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
<12>[ 18.419977] Starting lvm2 during preinit
<14>[ 19.688719] mount_root: loading kmods from internal overlay
<14>[ 19.728154] kmodloader: loading kernel modules from //etc/modules-boot.d/*
<14>[ 19.735028] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
<5>[ 19.875992] UBIFS (ubi0:1): Mounting in unauthenticated mode
<5>[ 19.877176] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 219
<5>[ 20.014816] UBIFS (ubi0:1): recovery needed
<5>[ 20.434249] UBIFS (ubi0:1): recovery completed
<5>[ 20.434384] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
<5>[ 20.437672] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
<5>[ 20.445499] UBIFS (ubi0:1): FS size: 82280448 bytes (78 MiB, 648 LEBs), max 659 LEBs, journal size 4063232 bytes (3 MiB, 32 LEBs)
<5>[ 20.455469] UBIFS (ubi0:1): reserved for root: 3886308 bytes (3795 KiB)
<5>[ 20.467091] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 4E261E68-E706-41E9-8AC8-7459F0A0CED9, small LPT model
<14>[ 20.475656] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
<14>[ 20.499789] block: extroot: not configured
<5>[ 20.503324] UBIFS (ubi0:1): un-mount UBI device 0
<5>[ 20.503391] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
<5>[ 20.511729] UBIFS (ubi0:1): Mounting in unauthenticated mode
<5>[ 20.516000] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 220
<5>[ 20.816211] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
<5>[ 20.816253] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
<5>[ 20.823033] UBIFS (ubi0:1): FS size: 82280448 bytes (78 MiB, 648 LEBs), max 659 LEBs, journal size 4063232 bytes (3 MiB, 32 LEBs)
<5>[ 20.833014] UBIFS (ubi0:1): reserved for root: 3886308 bytes (3795 KiB)
<5>[ 20.844647] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 4E261E68-E706-41E9-8AC8-7459F0A0CED9, small LPT model
<14>[ 20.902901] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
<14>[ 20.909321] block: extroot: not configured
<14>[ 20.912384] mount_root: switching to ubifs overlay
<12>[ 20.934250] urandom-seed: Seeding with /etc/urandom.seed
<14>[ 21.157821] procd: - early -
<14>[ 21.158073] procd: - watchdog -
<14>[ 21.159986] procd: Watchdog has previously reset the system
<14>[ 21.833802] procd: - watchdog -
<14>[ 21.833948] procd: Watchdog has previously reset the system
<14>[ 21.839102] procd: - ubus -
<14>[ 22.010705] procd: - init -
<14>[ 22.832734] urngd: v1.0.2 started.
<14>[ 22.988231] kmodloader: loading kernel modules from /etc/modules.d/*
<6>[ 23.001964] NET: Registered PF_ALG protocol family
<5>[ 23.027706] Key type dns_resolver registered
<6>[ 23.050093] RPC: Registered named UNIX socket transport module.
<6>[ 23.050133] RPC: Registered udp transport module.
<6>[ 23.054874] RPC: Registered tcp transport module.
<6>[ 23.059770] RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>[ 23.090293] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
<6>[ 23.094996] gre: GRE over IPv4 demultiplexor driver
<6>[ 23.096273] ip_gre: GRE over IPv4 tunneling driver
<5>[ 23.129239] NFS: Registering the id_resolver key type
<5>[ 23.129312] Key type id_resolver registered
<5>[ 23.133375] Key type id_legacy registered
<6>[ 23.140010] cryptodev: driver 1.12 loaded.
<6>[ 23.146661] PPP generic driver version 2.4.2
<6>[ 23.147896] NET: Registered PF_PPPOX protocol family
<6>[ 23.161457] GACT probability on
<6>[ 23.162569] Mirror/redirect action on
<6>[ 23.170179] u32 classifier
<6>[ 23.170210] input device check on
<6>[ 23.171812] Actions configured
<6>[ 23.189454] fuse: init (API version 7.34)
<6>[ 23.205143] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2
<6>[ 23.205202] Backport generated by backports.git v5.15.81-1-41-g02e352527db5
<6>[ 23.223489] PPTP driver version 0.8.5
<6>[ 23.240859] xt_time: kernel timezone is -0000
<6>[ 23.380778] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
<6>[ 23.380819] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
<7>[ 23.408712] ath10k_pci 0000:01:00.0: assign IRQ: got 47
<6>[ 23.409395] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
<7>[ 23.409485] ath10k_pci 0000:01:00.0: enabling bus mastering
<7>[ 23.409898] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x4362b498
<6>[ 23.410053] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
<6>[ 28.214265] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
<6>[ 28.214317] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
<6>[ 28.225624] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.9.0.2-00157 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 6cdc6ff9
<6>[ 30.504941] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 826c8c57
<6>[ 34.273653] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 512 raw 0 hwcrypto 1
<7>[ 34.363944] ath: EEPROM regdomain: 0x0
<7>[ 34.363965] ath: EEPROM indicates default country code should be used
<7>[ 34.363977] ath: doing EEPROM country->regdmn map search
<7>[ 34.363993] ath: country maps to regdmn code: 0x3a
<7>[ 34.364006] ath: Country alpha2 being used: US
<7>[ 34.364018] ath: Regpair used: 0x3a
<3>[ 34.364130] backports-6.1-rc8/net/mac80211/main.c:1325: ieee80211_register_hw: setting default CoDeL params for phy
<6>[ 34.366518] wlan0: Created a NSS virtual interface
<7>[ 34.376097] ath10k_pci 0001:01:00.0: assign IRQ: got 49
<6>[ 34.377278] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
<7>[ 34.378405] ath10k_pci 0001:01:00.0: enabling bus mastering
<7>[ 34.378984] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43597498
<6>[ 34.379162] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
<6>[ 35.658305] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
<6>[ 35.658365] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
<6>[ 35.669605] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.9.0.2-00157 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 6cdc6ff9
<6>[ 37.946210] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 826c8c57
<6>[ 41.724069] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 512 raw 0 hwcrypto 1
<7>[ 41.813247] ath: EEPROM regdomain: 0x0
<7>[ 41.813269] ath: EEPROM indicates default country code should be used
<7>[ 41.813282] ath: doing EEPROM country->regdmn map search
<7>[ 41.813297] ath: country maps to regdmn code: 0x3a
<7>[ 41.813311] ath: Country alpha2 being used: US
<7>[ 41.813324] ath: Regpair used: 0x3a
<3>[ 41.813411] backports-6.1-rc8/net/mac80211/main.c:1325: ieee80211_register_hw: setting default CoDeL params for phy
<3>[ 41.815588] debugfs: File 'virt_if' in directory 'stats' already present!
<6>[ 41.823173] wlan1: Created a NSS virtual interface
<14>[ 41.835409] kmodloader: done loading kernel modules from /etc/modules.d/*
<6>[ 46.383364] ECM init ( QSDK 12.1.r5_CS1 2022-11-25 1c401a1 )
<6>[ 46.383448] ECM database jhash random seed: 0x1619c734
<6>[ 46.392645] ECM init complete
<6>[ 49.902852] ipq8064-mdio 37000000.mdio eth0: nss_gmac_start_up: Force link up
<6>[ 49.902899] ipq8064-mdio 37000000.mdio eth0: 1000 Mbps Full Duplex
<6>[ 49.909126] ipq8064-mdio 37000000.mdio eth0: nss_gmac_dev_set_speed:NSS_ETH_CLK_DIV0(0xc) - 0x100
<6>[ 49.915064] ipq8064-mdio 37000000.mdio eth0: nss_gmac_reset: eth0 resetting...
<6>[ 51.047126] ipq8064-mdio 37000000.mdio eth0: GMAC reset completed in 113 jiffies; dma_bus_mode - 0x20100
<6>[ 51.047363] ipq8064-mdio 37000000.mdio eth0: nss_gmac_change_mtu: Enabling Normal Frame MTU (Requested MTU [1500])
<6>[ 51.055720] ipq8064-mdio 37000000.mdio eth0: Set addr a0:04:60:09:e4:14
<6>[ 51.065938] ipq8064-mdio 37000000.mdio eth0: nss_gmac_ipc_offload_init: enable Rx checksum
<6>[ 51.072361] ipq8064-mdio 37000000.mdio eth0: nss_gmac_config_flow_control:
<6>[ 51.080769] ipq8064-mdio 37000000.mdio eth0: nss_gmac_rx_pause_disable: disable Rx flow control
<6>[ 51.087641] ipq8064-mdio 37000000.mdio eth0: nss_gmac_tx_pause_disable: disable Tx flow control
<6>[ 51.096610] ipq8064-mdio 37000000.mdio eth0: nss_gmac_linkup: data plane open command successfully issued
<6>[ 51.113083] ipq8064-mdio 37000000.mdio eth1: nss_gmac_start_up: Force link up
<6>[ 51.114548] ipq8064-mdio 37000000.mdio eth1: 1000 Mbps Full Duplex
<6>[ 51.121760] ipq8064-mdio 37000000.mdio eth1: nss_gmac_dev_set_speed:NSS_ETH_CLK_DIV0(0xc) - 0x100
<6>[ 51.127813] ipq8064-mdio 37000000.mdio eth1: nss_gmac_dev_set_speed: qsgmii_base(0xde980000) + PCS_MODE_CTL(0x68): 0x80008082
<6>[ 51.136753] ipq8064-mdio 37000000.mdio eth1: Set addr a0:04:60:09:e4:13
<6>[ 51.148031] ipq8064-mdio 37000000.mdio eth1: nss_gmac_ipc_offload_init: enable Rx checksum
<6>[ 51.154395] ipq8064-mdio 37000000.mdio eth1: nss_gmac_config_flow_control:
<6>[ 51.162802] ipq8064-mdio 37000000.mdio eth1: nss_gmac_rx_pause_disable: disable Rx flow control
<6>[ 51.169663] ipq8064-mdio 37000000.mdio eth1: nss_gmac_tx_pause_disable: disable Tx flow control
<6>[ 51.184251] ipq8064-mdio 37000000.mdio eth1: nss_gmac_linkup: data plane open command successfully issued
<6>[ 51.196640] br-lan: port 1(eth1.1) entered blocking state
<6>[ 51.196687] br-lan: port 1(eth1.1) entered disabled state
<6>[ 51.202203] device eth1.1 entered promiscuous mode
<6>[ 51.207440] device eth1 entered promiscuous mode
<6>[ 51.222914] br-lan: port 1(eth1.1) entered blocking state
<6>[ 51.222962] br-lan: port 1(eth1.1) entered forwarding state
<6>[ 51.241200] br-vlan: port 1(eth1.3) entered blocking state
<6>[ 51.241248] br-vlan: port 1(eth1.3) entered disabled state
<6>[ 51.246435] device eth1.3 entered promiscuous mode
<6>[ 51.262647] br-vlan: port 1(eth1.3) entered blocking state
<6>[ 51.262697] br-vlan: port 1(eth1.3) entered forwarding state
<6>[ 51.826917] wlan0: Destroyed NSS virtual interface
<6>[ 51.956828] wlan1: Destroyed NSS virtual interface
<3>[ 52.135444] debugfs: File 'virt_if' in directory 'stats' already present!
<6>[ 52.135735] Created a NSS virtual interface for dev [nssifb]
<6>[ 52.141315] NSS IFB data callback registered
<6>[ 52.147015] NSS IFB transmit callback registered
<6>[ 52.151782] NSS IFB module loaded.
<7>[ 52.348604] ath: EEPROM regdomain: 0x824f
<7>[ 52.348645] ath: EEPROM indicates we should expect a country code
<7>[ 52.351605] ath: doing EEPROM country->regdmn map search
<7>[ 52.357809] ath: country maps to regdmn code: 0x10
<7>[ 52.363063] ath: Country alpha2 being used: PA
<7>[ 52.367756] ath: Regpair used: 0x10
<7>[ 52.372086] ath: regdomain 0x824f dynamically updated by user
<7>[ 52.375501] ath: EEPROM regdomain: 0x824f
<7>[ 52.381472] ath: EEPROM indicates we should expect a country code
<7>[ 52.385374] ath: doing EEPROM country->regdmn map search
<7>[ 52.391534] ath: country maps to regdmn code: 0x10
<7>[ 52.396904] ath: Country alpha2 being used: PA
<7>[ 52.401428] ath: Regpair used: 0x10
<7>[ 52.405854] ath: regdomain 0x824f dynamically updated by user
<4>[ 52.471809] __nss_qdisc_init[2175]:parent (65536) and TC_H_ROOT (-1))
<4>[ 52.471835] __nss_qdisc_init[2176]:root->ops->owner (00000000) and THIS_MODULE (bf63f600))
<4>[ 52.471886] __nss_qdisc_init[2177]:NSS qdisc c59b1c00 (type 1) used along with non-nss qdiscs, or the interface is currently down
<6>[ 52.487534] 6ad4ab96: Found net device [eth0]
<6>[ 52.498276] 6ad4ab96: Net device [eth0] has NSS intf_num [1]
<6>[ 52.502578] Nexthop successfully set for [eth0] to [nssifb]
<3>[ 54.336161] debugfs: File 'virt_if' in directory 'stats' already present!
<6>[ 54.336435] phy1-ap0: Created a NSS virtual interface
<4>[ 60.823099] ath10k_pci 0001:01:00.0: Unknown eventid: 36933
<3>[ 60.826632] debugfs: File 'virt_if' in directory 'stats' already present!
<6>[ 60.827775] phy0-ap0: Created a NSS virtual interface
<6>[ 60.841083] br-lan: port 2(phy1-ap0) entered blocking state
<6>[ 60.841128] br-lan: port 2(phy1-ap0) entered disabled state
<6>[ 60.845757] device phy1-ap0 entered promiscuous mode
<6>[ 60.851237] br-lan: port 2(phy1-ap0) entered blocking state
<6>[ 60.856293] br-lan: port 2(phy1-ap0) entered forwarding state
<6>[ 60.876178] br-lan: port 2(phy1-ap0) entered disabled state
<6>[ 61.406414] br-lan: port 2(phy1-ap0) entered blocking state
<6>[ 61.406467] br-lan: port 2(phy1-ap0) entered forwarding state
<6>[ 61.626012] 6ad4ab96: Reset nexthop successful for net device [eth0].
<6>[ 61.634010] NSS IFB transmit callback unregistered
<6>[ 61.636672] NSS virtual interface destroyed for dev [nssifb]
<4>[ 68.677653] ath10k_pci 0000:01:00.0: Unknown eventid: 36933
<6>[ 68.680237] br-lan: port 3(phy0-ap0) entered blocking state
<6>[ 68.682048] br-lan: port 3(phy0-ap0) entered disabled state
<6>[ 68.687923] device phy0-ap0 entered promiscuous mode
<6>[ 68.693265] br-lan: port 3(phy0-ap0) entered blocking state
<6>[ 68.698441] br-lan: port 3(phy0-ap0) entered forwarding state
<6>[ 68.705639] br-lan: port 3(phy0-ap0) entered disabled state
<3>[ 68.818583] debugfs: File 'virt_if' in directory 'stats' already present!
<6>[ 68.818906] Created a NSS virtual interface for dev [nssifb]
<6>[ 68.824398] NSS IFB data callback registered
<6>[ 68.830246] NSS IFB transmit callback registered
<4>[ 68.970055] __nss_qdisc_init[2175]:parent (65536) and TC_H_ROOT (-1))
<4>[ 68.970074] __nss_qdisc_init[2176]:root->ops->owner (00000000) and THIS_MODULE (bf63f600))
<4>[ 68.970113] __nss_qdisc_init[2177]:NSS qdisc c96fe400 (type 1) used along with non-nss qdiscs, or the interface is currently down
<6>[ 68.981607] 6ad4ab96: Found net device [eth0]
<6>[ 68.995736] 6ad4ab96: Net device [eth0] has NSS intf_num [1]
<6>[ 69.000140] Nexthop successfully set for [eth0] to [nssifb]
<6>[ 69.074210] br-lan: port 3(phy0-ap0) entered blocking state
<6>[ 69.074265] br-lan: port 3(phy0-ap0) entered forwarding state
<1>[ 2283.723608] NSS core 0 signal COREDUMP COMPLETE 4000
<1>[ 2283.723667] bf281400: Starting NSS-FW logbuffer dump for core 0
<1>[ 2283.727672] bf281400: Warn: trap[813]: Trap on CHIP ID 00050000
<1>[ 2283.733389] bf281400: Warn: trap[620]: Trapped: TRAP_TD(00000004) DCAPT(3C000080)
<1>[ 2283.739206] bf281400: Warn: trap[645]: Trapped: Thread: 2, reason: 00000020, PC: 4002FBF4, previous PC: 4002FBF0
<1>[ 2283.746847] bf281400: Warn: trap[594]: A0_3: 4F71A294 402321C0 3F019940 4F71A296
<1>[ 2283.757086] bf281400: Warn: trap[594]: A4_7: 4F71A296 40053D04 3F019940 3F00AEF0
<1>[ 2283.764474] bf281400: Warn: trap[599]: D0_3: 00000026 00000001 00000009 4F71A284
<1>[ 2283.771843] bf281400: Warn: trap[599]: D4_7: 00060000 00000026 00000024 000005DC
<1>[ 2283.779222] bf281400: Warn: trap[599]: D8_11: 00000024 C0A80104 4CF9E534 00000000
<1>[ 2283.786600] bf281400: Warn: trap[599]: D12_15: 00000000 00000000 00D84001 00004002
<1>[ 2283.793980] bf281400: Warn: trap[649]: Thread_2 has non-recoverable trap
<3>[ 2283.801683] phy0-ap0: NSS TX failed with error: NSS_TX_FAILURE_NOT_READY
<1>[ 2283.804457] NSS core 1 signal COREDUMP COMPLETE 4000
<3>[ 2283.808392] phy0-ap0: NSS TX failed with error: NSS_TX_FAILURE_NOT_READY
<1>[ 2283.815063] bf285b00: Starting NSS-FW logbuffer dump for core 1
<3>[ 2283.819935] phy0-ap0: NSS TX failed with error: NSS_TX_FAILURE_NOT_READY
<0>[ 2283.826679] Kernel panic - not syncing: NSS FW coredump: bringing system down
<3>[ 2283.832268] phy0-ap0: NSS TX failed with error: NSS_TX_FAILURE_NOT_READY
<2>[ 2283.839267] CPU0: stopping
<4>[ 2283.839277] CPU: 0 PID: 12 Comm: ksoftirqd/0 Not tainted 5.15.98 #0
<4>[ 2283.839287] Hardware name: Generic DT based system
<4>[ 2283.839297] [<c030e7e8>] (unwind_backtrace) from [<c030a194>] (show_stack+0x14/0x20)
<4>[ 2283.839320] [<c030a194>] (show_stack) from [<c064cee0>] (dump_stack_lvl+0x40/0x4c)
<4>[ 2283.839339] [<c064cee0>] (dump_stack_lvl) from [<c030cfbc>] (do_handle_IPI+0x144/0x184)
<4>[ 2283.839354] [<c030cfbc>] (do_handle_IPI) from [<c030d018>] (ipi_handler+0x1c/0x2c)
<4>[ 2283.839364] [<c030d018>] (ipi_handler) from [<c037d3cc>] (handle_percpu_devid_irq+0x84/0x16c)
<4>[ 2283.839379] [<c037d3cc>] (handle_percpu_devid_irq) from [<c0376c5c>] (handle_domain_irq+0x68/0x94)
<4>[ 2283.839397] [<c0376c5c>] (handle_domain_irq) from [<c0666dec>] (gic_handle_irq+0x8c/0xb4)
<4>[ 2283.839414] [<c0666dec>] (gic_handle_irq) from [<c0300b7c>] (__irq_svc+0x5c/0x78)
<4>[ 2283.839429] Exception stack(0xc146bb00 to 0xc146bb48)
<4>[ 2283.839438] bb00: 60000093 1cd49000 00000000 c0c442fc 0000003c 00000000 60000013 00000000
<4>[ 2283.839445] bb20: bf8365b0 c83dad00 00000000 c146bd10 00000000 c146bb50 c0374678 c037467c
<4>[ 2283.839450] bb40: 60000013 ffffffff
<4>[ 2283.839455] [<c0300b7c>] (__irq_svc) from [<c037467c>] (vprintk_emit+0x1d0/0x1f8)
<4>[ 2283.839471] [<c037467c>] (vprintk_emit) from [<c03746c8>] (vprintk_default+0x24/0x2c)
<4>[ 2283.839482] [<c03746c8>] (vprintk_default) from [<c03710b8>] (_printk+0x1c/0x2c)
<4>[ 2283.839496] [<c03710b8>] (_printk) from [<bf7e4054>] (ieee80211_set_ringparam+0x330/0xd50 [mac80211])
<4>[ 2283.839748] [<bf7e4054>] (ieee80211_set_ringparam [mac80211]) from [<bf7e5b3c>] (ieee80211_sta_ps_transition+0x9a0/0x17fc [mac80211])
<4>[ 2283.839990] [<bf7e5b3c>] (ieee80211_sta_ps_transition [mac80211]) from [<bf7e785c>] (ieee80211_is_our_addr+0xe1c/0x2ad4 [mac80211])
<4>[ 2283.840227] [<bf7e785c>] (ieee80211_is_our_addr [mac80211]) from [<bf7e9d40>] (ieee80211_mark_rx_ba_filtered_frames+0x82c/0x1520 [mac80211])
<4>[ 2283.840465] [<bf7e9d40>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<bf7eb880>] (ieee80211_rx_list+0xe4c/0xe94 [mac80211])
<4>[ 2283.840702] [<bf7eb880>] (ieee80211_rx_list [mac80211]) from [<bf7eb8f0>] (ieee80211_rx_napi+0x28/0x90 [mac80211])
<4>[ 2283.840938] [<bf7eb8f0>] (ieee80211_rx_napi [mac80211]) from [<bf99c000>] (ath10k_htt_rx_pktlog_completion_handler+0xfa0/0x1428 [ath10k_core])
<4>[ 2283.841189] [<bf99c000>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core]) from [<bf9a0b8c>] (ath10k_htt_txrx_compl_task+0xa28/0x1240 [ath10k_core])
<4>[ 2283.841333] [<bf9a0b8c>] (ath10k_htt_txrx_compl_task [ath10k_core]) from [<bf9f0a54>] (ath10k_pci_napi_poll+0x5c/0x134 [ath10k_pci])
<4>[ 2283.841444] [<bf9f0a54>] (ath10k_pci_napi_poll [ath10k_pci]) from [<c085df2c>] (__napi_poll+0x5c/0x1d0)
<4>[ 2283.841472] [<c085df2c>] (__napi_poll) from [<c085e298>] (net_rx_action+0xe4/0x268)
<4>[ 2283.841485] [<c085e298>] (net_rx_action) from [<c0301304>] (__do_softirq+0x11c/0x2e4)
<4>[ 2283.841500] [<c0301304>] (__do_softirq) from [<c0325d98>] (run_ksoftirqd+0x38/0x4c)
<4>[ 2283.841516] [<c0325d98>] (run_ksoftirqd) from [<c034824c>] (smpboot_thread_fn+0xe8/0x1ac)
<4>[ 2283.841535] [<c034824c>] (smpboot_thread_fn) from [<c0343b50>] (kthread+0x158/0x174)
<4>[ 2283.841554] [<c0343b50>] (kthread) from [<c0300130>] (ret_from_fork+0x14/0x24)
<4>[ 2283.841565] Exception stack(0xc146bfb0 to 0xc146bff8)
<4>[ 2283.841573] bfa0: 00000000 00000000 00000000 00000000
<4>[ 2283.841579] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
<4>[ 2283.841585] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000