Netgear 4300V2 bootlooping

Installing and Using OpenWrt
21

Try 57600.

22

already did. messed up more

23

so try 38400, 19200, 9600, 4800, 2400, 1200 ....

24

Got response on 128000



U-Boot 1.1.4 (Aug 12 2014 - 15:21:46)

U-boot dni29 V0.5 for DNI HW ID: 29764821 NOR flash 2MB NAND flash 128MB RAM 128MB
 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x10, 0x10, 0x10, 0x10)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 265k for U-Boot at: 87fbc000
Reserving 192k for malloc() at: 87f8c000
Reserving 44 Bytes for Board Info at: 87f8bfd4
Reserving 36 Bytes for Global Data at: 87f8bfb0
Reserving 128k for boot params() at: 87f6bfb0
Stack Pointer at: 87f6bf98
Now running in RAM - U-Boot at: 87fbc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash:  2 MB
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014  Qualcomm Atheros Inc.
ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1
====== NAND Parameters ======
sc = 0x87ff77e4 page = 0x800 block = 0x20000In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
Fetching MAC Address from 0x87fe914c
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: a0:63:91:89:e6:45
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot:  0
Trying eth0
eth0 link down
FAIL

 Client starts...[Listening] for ADVERTISE...TTT

what to do with this?


U-Boot 1.1.4 (Aug 12 2014 - 15:21:46)

U-boot dni29 V0.5 for DNI HW ID: 29764821 NOR flash 2MB NAND flash 128MB RAM 128MB
 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x10, 0x10, 0x10, 0x10)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 265k for U-Boot at: 87fbc000
Reserving 192k for malloc() at: 87f8c000
Reserving 44 Bytes for Board Info at: 87f8bfd4
Reserving 36 Bytes for Global Data at: 87f8bfb0
Reserving 128k for boot params() at: 87f6bfb0
Stack Pointer at: 87f6bf98
Now running in RAM - U-Boot at: 87fbc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash:  2 MB
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014  Qualcomm Atheros Inc.
ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1
====== NAND Parameters ======
sc = 0x87ff77e4 page = 0x800 block = 0x20000In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
Fetching MAC Address from 0x87fe914c
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: a0:63:91:89:e6:45
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot:  0
Trying eth0
eth0 link down
FAIL

 Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual

 nmrp server is stopped or failed !

Loading from device 0: ath-spi-nand (offset 0x0)

** check kernel image **
   Verifying Checksum ... OK

** check rootfs image **
   Verifying Checksum ... OK
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-5.4.188
   Created:      2022-04-16  12:59:34 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4194175 Bytes =  4 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is Netgear WNDR4300 v2
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 121920K/131072K available (5521K kernel code, 178K rwdata, 708K rodata, 1200K init, 210K bss, 9152K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] random: get_random_bytes called from 0x806a4a28 with crng_init=0
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000006] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008228] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[    0.046712] pid_max: default: 32768 minimum: 301
[    0.051713] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.059424] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.071806] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.082104] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.089390] pinctrl core: initialized pinctrl subsystem
[    0.096120] NET: Registered protocol family 16
[    0.127356] clocksource: Switched to clocksource MIPS
[    0.133561] thermal_sys: Registered thermal governor 'step_wise'
[    0.133905] NET: Registered protocol family 2
[    0.145019] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.153369] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.162251] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.170346] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.177791] TCP: Hash tables configured (established 1024 bind 1024)
[    0.184618] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.191559] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.199182] NET: Registered protocol family 1
[    0.203835] PCI: CLS 0 bytes, default 32
[    0.211593] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.224628] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.230820] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.254248] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.265462] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.272531] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.281310] printk: console [ttyS0] disabled
[    0.285906] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
β–’@@@@p^byu`a`β–’@β–’β–’β–’β–’β–’β–’z@β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’`β–’@β–’β–’β–’β–’β–’β–’β–’
                                             β–’@@@@p^bye`q`β–’@β–’β–’β–’β–’β–’β–’z@β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’`β–’@β–’β–’β–’β–’β–’β–’β–’β–’@@@@`^s`d`vnβ–’@β–’β–’β–’β–’β–’β–’z@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’`β–’@β–’β–’β–’β–’β–’β–’β–’β–’
                                                              β–’@@@@p^cpd`vfβ–’@β–’β–’β–’β–’β–’β–’z@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’`β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’@@@@`^crcybsβ–’@β–’β–’β–’]β–’β–’β–’β–’@β–’β–’β–’`^qr@β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’β–’^β–’@@@@`^sbygrnβ–’@β–’β–’β–’]β–’β–’β–’β–’@β–’β–’β–’`Naz@qbx@β–’Ρ‚\@β–’β–’β–’β–’β–’@β–’β–’β–’β–’z@qbx@β–’Ρ‚\@β–’β–’β–’β–’@β–’β–’β–’β–’r@bplx\@β–’β–’β–’@β–’β–’β–’β–’r@fdβ–’@@@@`^ccyarnβ–’@r@β–’β–’β–’β–’β–’]β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’@β–’β–’@β–’β–’β–’@β–’β–’β–’β–’β–’β–’@β–’β–’β–’`^aβ–’@@@@p^cduocgβ–’@β–’β–’β–’β–’β–’β–’β–’β–’@b@β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’@Bβ–’β–’β–’`^aBrβ–’@@@@`^ce`w`fβ–’@`β–’`p``````````]`β–’```p``dp````@z@Bβ–’β–’β–’β–’β–’β–’B
                                           β–’@@@@`^sn`xulβ–’@`β–’``````d````p]`β–’p````p``````@r@Bβ–’β–’β–’B
               β–’@@@@`^dyfmc`β–’@β–’β–’β–’Mβ–’β–’β–’@β–’β–’β–’`^`z@β–’β–’beβ–’af`vβ–’@Xr`dx@β–’β–’β–’β–’β–’β–’Yβ–’@@@@`^m`agubβ–’@x@β–’β–’β–’β–’β–’]β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’@β–’β–’@β–’β–’β–’@β–’β–’β–’β–’β–’β–’@β–’β–’β–’`^`β–’@@@@`Nm`xcbgβ–’@β–’β–’β–’β–’β–’β–’β–’β–’@p@β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’@Bβ–’β–’β–’p^`Bzβ–’@@@@`^uacbyaβ–’@pβ–’````````````]`β–’p```p``d````@r@Bβ–’]β–’β–’β–’β–’Bβ–’@@@@`^uaybxbβ–’@pβ–’```````l````]`β–’p```p``e````@r@Bβ–’]β–’β–’β–’β–’]β–’β–’β–’Bβ–’@@@@p^ebenecβ–’@`β–’`p```p`e`p``]`β–’```````n```p@z@Bβ–’β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’B
                                                  β–’@@@@p^ecrceyβ–’@`β–’```````f`p``]β–’@@@@`^mcxctqβ–’@pβ–’```````o````]`β–’p```p``xp```@r@Bβ–’β–’β–’β–’β–’β–’ΓΏβ–’β–’β–’β–’β–’Bβ–’@@@@`^ule`ppβ–’@`β–’```````p```p]`β–’p``````y````@r@Bβ–’β–’β–’B
                                 β–’@@@@p^ee`ocaβ–’@`β–’`````p`y`p``]`β–’``````aβ–’```p@z@β–’@@@@a^adgslxβ–’@β–’β–’β–’β–’β–’β–’z@β–’β–’β–’β–’@β–’β–’β–’β–’@β–’β–’β–’β–’β–’@@@@a^b`fwpyβ–’@β–’β–’β–’β–’β–’β–’`z@β–’β–’β–’β–’β–’β–’β–’@β–’β–’xscg@β–’β–’β–’^@b@β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’@β–’β–’β–’β–’^`β–’@@@@a^gydplfβ–’@β–’β–’gqβ–’β–’@qq``````^β–’β–’β–’z@β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’@β–’β–’β–’@β–’β–’@β–’β–’β–’β–’N`z`p@β–’β–’β–’β–’}``lβ–’β–’`cn\@β–’β–’β–’β–’β–’β–’}β–’β–’β–’β–’β–’β–’β–’@β–’β–’pbaf_β–’β–’xrcf_β–’β–’xcqnβ–’β–’@@@@a^x`naagβ–’@β–’β–’β–’`z@β–’β–’β–’β–’β–’β–’β–’@β–’β–’oaβ–’β–’@β–’β–’@`β–’β–’y```p``\@β–’β–’β–’@l\@β–’β–’β–’β–’z@β–’β–’β–’β–’β–’β–’@@@@a^xamabfβ–’@β–’β–’β–’r@β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’@a`β–’@@@@q^xbdp`cβ–’@β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’@β–’β–’β–’nβ–’@@@@a^xbxgdpβ–’@β–’@@@@a^xcclcfβ–’@β–’β–’β–’β–’β–’β–’z@β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’_β–’β–’_β–’β–’fβ–’β–’β–’β–’β–’β–’@β–’β–’@β–’β–’@β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’@β–’@@@@a^pdfxbyβ–’@p`bqβ–’z@x`b^aβ–’@β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’@β–’a^xβ–’@@@@a^xmcducβ–’@β–’β–’β–’@β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’@_β–’β–’β–’_β–’β–’β–’β–’]β–’β–’β–’β–’β–’β–’β–’β–’β–’β–’axbe````@β–’β–’β–’β–’β–’β–’rβ–’@@@@a^xmyxbbβ–’@@β–’β–’β–’@pβ–’``p```p`ab``````^^`β–’```p```pacβ–’β–’β–’β–’β–’β–’β–’@@@@a^xnebclβ–’@@@β–’β–’@`β–’``p```p`````````^^`β–’```p```p```p````β–’@@@@aNpg`gqdβ–’@β–’β–’β–’@β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’@β–’β–’@β–’β–’β–’@````z`pβ–’@@@@a^xoe`foβ–’@β–’β–’ΡΏβ–’β–’β–’@`p``zp`z@β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’@`β–’ab``````]pβ–’acβ–’β–’β–’β–’β–’Ξ½β–’@@@@a^ppbawnβ–’@β–’β–’ΩΏβ–’β–’β–’@````z``z@β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’@@`β–’p```β–’β–’@@@@a^xxoyceβ–’@β–’β–’ΙΏβ–’β–’β–’@``p`z``r@β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’@`β–’``````p`@β–’β–’β–’β–’β–’@`β–’`β–’β–’@@@@a^xytqdyβ–’@β–’β–’ΩΏβ–’β–’β–’@````r``z@β–’β–’@β–’β–’β–’β–’@β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’@β–’β–’β–’\@β–’β–’β–’β–’@β–’β–’β–’@β–’β–’β–’β–’@``]β–’Ζ½β–’@@@@aNq`cqnfβ–’@β–’β–’β–’@````r``zp`^`z@β–’afpβ–’zβ–’β–’β–’Δ½@β–’β–’β–’β–’@``@β–’β–’β–’β–’β–’@`β–’`b````β–’@@@@a^yβ–’@@@@a^yafdymβ–’@β–’β–’β–’@````zp`z`p^`z@β–’β–’β–’@`β–’c`r@β–’β–’β–’β–’@`β–’```p````]`β–’````β–’β–’β–’β–’@β–’β–’β–’Ζ½β–’@@@@a^ybcdyqβ–’@β–’β–’β–’@````z``z`p^`z@β–’β–’β–’β–’β–’β–’β–’β–’@β–’aβ–’@@@@aNqbgvlgβ–’@β–’β–’β–’@````r``z``^`z@β–’β–’β–’C@β–’β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’@β–’`@β–’a@β–’sβ–’β–’β–’β–’@@@@a^ycdfccβ–’@β–’β–’ΡΏβ–’β–’β–’@`p``z``z@β–’β–’β–’ήΏβ–’β–’β–’z@β–’β–’β–’β–’@``Mβ–’Ζ½@β–’β–’β–’@β–’β–’@β–’β–’β–’β–’β–’β–’β–’@β–’β–’@``β–’@@@@q^ydamagβ–’@β–’β–’β–’@```pr``z``^pr@β–’β–’β–’@`z@β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’@`β–’ab``````]`β–’ar`aβ–’β–’β–’β–’@flβ–’β–’β–’β–’@@@@a^yly`ymβ–’@β–’β–’β–’@````z``z``^`z@β–’β–’β–’@nz@β–’β–’β–’β–’β–’β–’β–’β–’@β–’β–’β–’β–’@`β–’ar`b`p``]`β–’ab`bβ–’β–’β–’β–’@β–’β–’β–’Ξ½
              β–’@@@@a^yeycbxβ–’@β–’β–’β–’r@β–’β–’β–’β–’]β–’
25

Thanks, @frollic @mk24 @tmomas @Borromini
Got my bricked router to start working again.
Used a mix of serial and nmrp tool with "WNDR4300v2-V1.0.0.60 firmware oldest one is not working with a bad checksum, this one worked even though same error but it flashed.

Screenshot 2022-10-06 230403
Screenshot 2022-10-06 2304031498Γ—873 33.2 KB

Screenshot 2022-10-06 225917
Screenshot 2022-10-06 2259171728Γ—681 224 KB

Summary 
U-Boot 1.1.4 (Aug 12 2014 - 15:21:46)

U-boot dni29 V0.5 for DNI HW ID: 29764821 NOR flash 2MB NAND flash 128MB RAM 128                                                                                                                                                             MB
 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x10, 0x10, 0x10, 0x10)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 265k for U-Boot at: 87fbc000
Reserving 192k for malloc() at: 87f8c000
Reserving 44 Bytes for Board Info at: 87f8bfd4
Reserving 36 Bytes for Global Data at: 87f8bfb0
Reserving 128k for boot params() at: 87f6bfb0
Stack Pointer at: 87f6bf98
Now running in RAM - U-Boot at: 87fbc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash:  2 MB
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014  Qualcomm Atheros Inc.
ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1
====== NAND Parameters ======
sc = 0x87ff77e4 page = 0x800 block = 0x20000In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
Fetching MAC Address from 0x87fe914c
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: a0:63:91:89:e6:45
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot:  0
Trying eth0
dup 1 speed 1000

 Client starts...[Listening] for ADVERTISE...checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Tchecksum bad
checksum bad
Tchecksum bad
checksum bad
checksum bad
checksum bad
checksum bad
T
NMRP CONFIGING
Recv FW-UP option

No ST-UP option

NMRP WAITING FOR UPLOAD FIRMWARE or STRING TABLES!
Trying eth0
Listening on Port : 69, IP Address: 10.164.183.253...
checksum bad

Rcv:
        checksum bad
checksum bad
checksum bad
T .................................................................
        ..........................................................checksum bad
......checksum bad
.
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        .................................................................
        ...............................................
Done!
Bytes transferred = 14549125 (de0085 hex)
TFTP upload done
Ignore Magic number checking when upgrade via NMRP,Magic number is 27051956!
HW ID on board: 29764821+2+128+128+3x3+3x3+5508012175
HW ID on image: 29764821+2+128+128
Firmware Image HW ID matched Board HW ID

nand erase: off 0, size 20000: OK
nand write 0 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 20000, size 20000: OK
nand write 20000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 40000, size 20000: OK
nand write 40000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 60000, size 20000: OK
nand write 60000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 80000, size 20000: OK
nand write 80000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off a0000, size 20000: OK
nand write a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off c0000, size 20000: OK
nand write c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off e0000, size 20000: OK
nand write e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 100000, size 20000: OK
nand write 100000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 120000, size 20000: OK
nand write 120000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 140000, size 20000: OK
nand write 140000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 160000, size 20000: OK
nand write 160000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 180000, size 20000: OK
nand write 180000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 1a0000, size 20000: OK
nand write 1a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 1c0000, size 20000: OK
nand write 1c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 1e0000, size 20000: OK
nand write 1e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 200000, size 20000: OK
nand write 200000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 220000, size 20000: OK
nand write 220000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 240000, size 20000: OK
nand write 240000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 260000, size 20000: OK
nand write 260000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 280000, size 20000: OK
nand write 280000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 2a0000, size 20000: OK
nand write 2a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 2c0000, size 20000: OK
nand write 2c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 2e0000, size 20000: OK
nand write 2e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 300000, size 20000: OK
nand write 300000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 320000, size 20000: OK
nand write 320000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 340000, size 20000: OK
nand write 340000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 360000, size 20000: OK
nand write 360000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 380000, size 20000: OK
nand write 380000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 3a0000, size 20000: OK
nand write 3a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 3c0000, size 20000: OK
nand write 3c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 3e0000, size 20000: OK
nand write 3e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 400000, size 20000: OK
nand write 400000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 420000, size 20000: OK
nand write 420000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 440000, size 20000: OK
nand write 440000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 460000, size 20000: OK
nand write 460000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 480000, size 20000: OK
nand write 480000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 4a0000, size 20000: OK
nand write 4a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 4c0000, size 20000: OK
nand write 4c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 4e0000, size 20000: OK
nand write 4e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 500000, size 20000: OK
nand write 500000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 520000, size 20000: OK
nand write 520000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 540000, size 20000: OK
nand write 540000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 560000, size 20000: OK
nand write 560000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 580000, size 20000: OK
nand write 580000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 5a0000, size 20000: OK
nand write 5a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 5c0000, size 20000: OK
nand write 5c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 5e0000, size 20000: OK
nand write 5e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 600000, size 20000: OK
nand write 600000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 620000, size 20000: OK
nand write 620000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 640000, size 20000: OK
nand write 640000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 660000, size 20000: OK
nand write 660000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 680000, size 20000: OK
nand write 680000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 6a0000, size 20000: OK
nand write 6a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 6c0000, size 20000: OK
nand write 6c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 6e0000, size 20000: OK
nand write 6e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 700000, size 20000: OK
nand write 700000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 720000, size 20000: OK
nand write 720000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 740000, size 20000: OK
nand write 740000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 760000, size 20000: OK
nand write 760000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 780000, size 20000: OK
nand write 780000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 7a0000, size 20000: OK
nand write 7a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 7c0000, size 20000: OK
nand write 7c0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 7e0000, size 20000: OK
nand write 7e0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 800000, size 20000: OK
nand write 800000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 820000, size 20000: OK
nand write 820000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 840000, size 20000: OK
nand write 840000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 860000, size 20000: OK
nand write 860000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 880000, size 20000: OK
nand write 880000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 8a0000, size 20000: OK
nand write 8a0000 : 20000 bytes written, OK
Alive-timer 0
nand erase: off 8c0000, size 20000: OK
nand write 8c0000 : 20000 bytes written, OK
timestamp overflows
Alive-timer 11
nand erase: off 8e0000, size 20000: OK
nand write 8e0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 900000, size 20000: OK
nand write 900000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 920000, size 20000: OK
nand write 920000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 940000, size 20000: OK
nand write 940000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 960000, size 20000: OK
nand write 960000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 980000, size 20000: OK
nand write 980000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 9a0000, size 20000: OK
nand write 9a0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 9c0000, size 20000: OK
nand write 9c0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off 9e0000, size 20000: OK
nand write 9e0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off a00000, size 20000: OK
nand write a00000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off a20000, size 20000: OK
nand write a20000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off a40000, size 20000: OK
nand write a40000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off a60000, size 20000: OK
nand write a60000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off a80000, size 20000: OK
nand write a80000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off aa0000, size 20000: OK
nand write aa0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off ac0000, size 20000: OK
nand write ac0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off ae0000, size 20000: OK
nand write ae0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off b00000, size 20000: OK
nand write b00000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off b20000, size 20000: OK
nand write b20000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off b40000, size 20000: OK
nand write b40000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off b60000, size 20000: OK
nand write b60000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off b80000, size 20000: OK
nand write b80000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off ba0000, size 20000: OK
nand write ba0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off bc0000, size 20000: OK
nand write bc0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off be0000, size 20000: OK
nand write be0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off c00000, size 20000: OK
nand write c00000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off c20000, size 20000: OK
nand write c20000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off c40000, size 20000: OK
nand write c40000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off c60000, size 20000: OK
nand write c60000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off c80000, size 20000: OK
nand write c80000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off ca0000, size 20000: OK
nand write ca0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off cc0000, size 20000: OK
nand write cc0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off ce0000, size 20000: OK
nand write ce0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off d00000, size 20000: OK
nand write d00000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off d20000, size 20000: OK
nand write d20000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off d40000, size 20000: OK
nand write d40000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off d60000, size 20000: OK
nand write d60000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off d80000, size 20000: OK
nand write d80000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off da0000, size 20000: OK
nand write da0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off dc0000, size 20000: OK
nand write dc0000 : 20000 bytes written, OK
Alive-timer 11
nand erase: off de0000, size 20000: OK
nand write de0000 : 20000 bytes written, OK
Alive-timer 11
Original board MODEL ID: WNDR4500series
New MODEL ID from image: WNDR4500series
Updating MODEL ID

First 0x1f last 0x1f sector size 0x10000                                      31
write addr: 9f1f0000
done

NMRP Send Closing REQ
Trying eth0

NMRP CLOSEDRestore to factory default
Erase Flash from 0x9f060000 to 0x9f06ffff in Bank # 1
First 0x6 last 0x6 sector size 0x10000                                         6
Erased 1 sectors

press ctrl+C to continue.....
1 Like
26

next step is go back to OpenWrt, even though Homeassistant's Netgear integration is miles ahead of OpenWrt integration and is getting better by the day .

27

tried to flash openwrt 22, this was the serial output and but couldn't connect on 192.168.1.1. connection was refused. now bootlooping again
for complete log check pastebin link


Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000400: Oldval = 0x00000121 Newval = 0x80000221
Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x00003333
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x0000001e
Write Reg: 0x00000400: Oldval = 0x00000221 Newval = 0x80000022
Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x0000ffff
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x000000c9
Write Reg: 0x00000400: Oldval = 0x00000022 Newval = 0x80000122
Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0xe0000000
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000013
Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000400: Oldval = 0x00000122 Newval = 0x80000222
Write Reg: 0x00000404: Oldval = /proc/qca_switch/nf_athrs17_hnat is created
0x00000000 Newva/proc/qca_switch/nf_athrs17_hnat_wan_type is created
l = 0x00000000
/proc/qca_switch/nf_athrs17_hnat_ppp_id is created
Write Reg: 0x000/proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
00408: Oldval = /proc/qca_switch/nf_athrs17_hnat_wan_ip is created
0x00000000 Newva/proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
l = 0x00003333
/proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
Write Reg: 0x000/proc/qca_switch/nf_athrs17_hnat_wan_mac is created
0040c: Oldval = /proc/qca_switch/nf_athrs17_hnat_ppp_id2 is created
0x00000000 Newva/proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
l = 0x00000000
Adding ACL rules 15 - upnp_ssdp_add_acl_rules
Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000002
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000001
Write Reg: 0x00000400: Oldval = 0x00000222 Newval = 0x80000023
Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x0000ffff
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000410: Oldval = 0x00000000 NewvaAdding ACL rules 8 - ipv6_snooping_solicted_node_add_acl_rules
l = 0x00000000
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x000000f9
Write Reg: 0x00000400: Oldval = 0x00000023 Newval = 0x80000123
Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000014
Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000
Write Reg: 0x00000400: Oldval = 0x00000123 Newval = 0x80000223
Adding ACL rules 12 - ipv6_snooping_sextuple0_group_add_acl_rules
Adding ACL rules 14 - ipv6_snooping_quintruple0_1_group_add_acl_rules
Hello, nat helper module for 1.1!

######## S17 SSDK init succeeded! ########
Error: cannot be initialized twice!
athrs17_reg_init:done
955x_SGMII::athr_gmac_sgmii_setup  Done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Phy setup Complete
To set s17 LOOKUP_CTRL_REG registers, flag 1
ADDRCONF(NETDEV_UP): phy0: link is not ready
init.enet: Default WAN MAC is : a0:63:91:89:e6:46
device eth0 entered promiscuous mode
device phy0 entered promiscuous mode
init.enet: Default LAN MAC is : a0:63:91:89:e6:45
Loading DNI-ENET driver
device pas0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering forwarding state

 SSDK Init OK!
operate done.

udhcp server (v0.9.8) started
The attached devices demo is Running ...
The telnetenable is running ...
Deleting static route ... Done!
Adding static route ... Done!
usbcore: deregistering interface driver usbserial_generic
USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
rmmod: cdc_ncm: No such file or directory
killall: failover: no process killed
rmmod: usbserial: No such file or directory
rmmod: usbserial: No such file or directory
dni-qos attached on eth1.
br0: port 1(eth0) entering disabled state
dni-qos attached on br0.
br0: port 1(eth0) entering forwarding state
udhcp client (v0.9.8) started
time zone index is : 21
Run NTP Client with setting: pri:time-b.netgear.com sec:time-c.netgear.com
no 6RD parameters available, so unset 6rd related config
killall: miniupnpd: no process killed
killall: pppd: no process killed
Deleting static route ... Done!
Deleting static route ... Done!
Adding static route ... Done!
Jan  1 00:00:28 miniupnpd[1048]: listening on 169.254.126.231:5555
start rip process
start initial data
Sending discover...
No user name for DDNS!
syslogd can't open the temp log file: /tmp/log/log-message or /var/log/messages
Starting Firewall...
AP Mode Rule: Done!
The region number is: 0x0001
REGION: NA
Generating RSA private key, 1024 bit long modulus
ufsd:: trace mask set to 0000000f
ufsd: driver (lke_9.0.0 lke_9.0.0_r233352_b3, LBD=ON, acl, ioctl, bdi, sd(0), wb, bz, tr) loaded at 87380000
NTFS support included
Big endian platform
optimized: speed
Build_for__NETGEAR_WNDR4500V3_k2.6.31_2014-06-18_lke_9.0.0_r233352_b3

kcg 354 :GPL NetUSB up!
INFO1A45: NetUSB 1.10.12, 0002061F : Jul 12 2019 14:03:38
INFO1A47: 7423: WNDR4500v3 :WNDR4500v3
INFO1A48:  AUTH ISOC
INFO1A49:  MOVE_HEAD emb_lp filterAudio
INFO0789:  0 : tunnelID emusblp 0
INFO0789:  1 : tunnelID emusblp 1
INFO0789:  2 : tunnelID emusblp 2
INFO0789:  3 : tunnelID emusblp 3
INFO0789:  4 : tunnelID emusblp 4
INFO0789:  5 : tunnelID emusblp 5
INFO0789:  6 : tunnelID emusblp 6
INFO0789:  7 : tunnelID emusblp 7
INFO0789:  8 : tunnelID emusblp 8
INFO0789:  9 : tunnelID emusblp 9
usbcore: registered new interface driver KC NetUSB General Driver
INFO0B43:  --- checkSBusTimeoutThread start ---
INFO019C:  init proc : PAGE_SIZE 4096
INFO193A:  infomap 87307ac8
INFO193E:  bndev : br0
INFO1943:  sleep to wait br0 to wake up
INFO173B: tcpConnector() started... : br0
Changing password for admin
New password:Sending discover...

Bad password: too weak
Retype password:
Password for admin changed by root

Enet:0 port3 up
956x_GMAC: Enet Unit:0 PHY:3 is UP eth0 SGMII 1000Mbps full duplex
956x_GMAC: done cfg2 0x7235 ifctl 0x0 miictrl
955x_SGMII::athr_gmac_sgmii_setup  Done
Setting Drop CRC Errors, Pause Frames and Length Error frames
ADDRCONF(NETDEV_CHANGE): phy0: link becomes ready
Generating selfsigned certificate with subject 'C=DE;ST=Saxony;L=Leipzig;CN=OpenWrt;' and validity 2001-09-09 01:46:40-2003-09-09 01:46:40
AUTO FW CHECK: power cycle
killall: smbd: no process killed
killall: smbd: no process killed
killall: nmbd: no process killed
USB Storage daemon is Running ...
Changing password for admin
New password:FW checking ...
/etc/rc.common: /etc/rc.common: 117: detplc: not found
DNS-LOOKUP: no dns server address in /tmp/resolv.conf

Can't resovle the host : updates1.netgear.com IP!

DNS-LOOKUP: no dns server address in /tmp/resolv.conf

Can't resovle the host : updates1.netgear.com IP!

week_day == 0
POT is Running...


cat: /var/run/afpd.pid: No such file or directory
the ipv6 wan type is disable
Sending discover...
Args: 1
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_tx99: Version 2.0
Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 10.2-00085-8 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
*** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ATH_TXBUF=540
Enterprise mode: 0x03bda000
Restoring Cal data from Flash
Green-AP : Green-AP : Attached

ath_get_caps[6148] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[6123] tx chainmask mismatch actual 3 sc_chainmak 0
ath_attach_dfs[12558] dfsdomain 1
ath_tx_paprd_init sc 87050000 PAPRD disabled in HAL
SC Callback Registration for wifi0
wifi0: Atheros 956X: mem=0xb8100000, irq=2
ath_pci: 10.2-00085-8 (Atheros/multi-bss)
__ath_attach: Set global_scn[1]
*** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ATH_TXBUF=540
Restoring Cal data from Flash
Green-AP : Green-AP : Attached

ath_get_caps[6148] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[6123] tx chainmask mismatch actual 7 sc_chainmak 0
ath_attach_dfs[12558] dfsdomain 1
ath_tx_paprd_init sc 870e0000 PAPRD disabled in HAL
SC Callback Registration for wifi1
wifi1: Atheros ???: mem=0x12000000, irq=76 hw_base=0xb2000000
ath_attach_dfs[12558] dfsdomain 1
ath_attach_dfs[12558] dfsdomain 1
Creating ap for NETGEAR65 on
wlan_vap_create : enter. devhandle=0x865a02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x865a02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created
Added ath0 mode master
Invalid command : bgscan
Interface doesn't accept private ioctl...
HALDbg (8BE0): Operation not permitted
Interface doesn't accept private ioctl...
ForBiasAuto (8BE0): Operation not permitted

 DES SSID SET=NETGEAR65
 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
Set freq vap stop send + 85444000
Set freq vap stop send -85444000
Set wait done --85444000
/etc/ath/makeVAP: /etc/ath/makeVAP: 492: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent
WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
    SET failed on device ath0 ; Invalid argument.
Invalid command : setVowExt
Invalid command : setKeySrchAlways
Invalid command : set_vsp_enable
Invalid command : setPhyRestartWar
Invalid command : setVowExtStats
sc nodebug 0
Created ath0 mode ap for NETGEAR65
lo        no wireless extensions.

sit0      no wireless extensions.

phy0      no wireless extensions.

br0       no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.

pas0      no wireless extensions.

wifi0     no wireless extensions.

wifi1     no wireless extensions.

Modules already loaded
Creating ap for NETGEAR65-5G on
wlan_vap_create : enter. devhandle=0x85bd02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x85bd02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath1 created
Added ath1 mode master
Invalid command : bgscan
Interface doesn't accept private ioctl...
HALDbg (8BE0): Operation not permitted
Invalid command : extoffset

 DES SSID SET=NETGEAR65-5G
 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
Set freq vap stop send + 85458000
Set freq vap stop send -85458000
Set wait done --85458000
/etc/ath/makeVAP: /etc/ath/makeVAP: 492: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent
WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
    SET failed on device ath1 ; Invalid argument.
Invalid command : setVowExt
Invalid command : setKeySrchAlways
Invalid command : set_vsp_enable
Invalid command : setPhyRestartWar
Invalid command : setVowExtStats
sc nodebug 0
Created ath1 mode ap for NETGEAR65-5G
lo        no wireless extensions.

sit0      no wireless extensions.

phy0      no wireless extensions.

br0       no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.

pas0      no wireless extensions.

wifi0     no wireless extensions.

wifi1     no wireless extensions.

No lease, forking to background.
lo        no wireless extensions.

sit0      no wireless extensions.

phy0      no wireless extensions.

br0       no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.

pas0      no wireless extensions.
device ath0 entered promiscuous mode

wifi0     no wireless extensions.

wifi1     no wireless extensions.

arping: bind: Cannot assign requested address
>>>>> WPS MODE, 2
>>>>> WPS ENABLED, PSK
cat: /etc/wpa2/WSC_ath0.conf: No such file or directory
>>>>> WPS Translate, Index:0
lo        no wireless extensions.

sit0      no wireless extensions.

phy0      no wireless extensions.

br0       no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.

pas0      no wireless extensions.
device ath1 entered promiscuous mode

wifi0     no wireless extensions.

wifi1     no wireless extensions.

arping: bind: Cannot assign requested address
>>>>> WPS MODE, 2
>>>>> WPS ENABLED, PSK
cat: /etc/wpa2/WSC_ath1.conf: No such file or directory
>>>>> WPS Translate, Index:2
Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
le: /etc/wpa2/WS DEVICE IS DOWN ifname=ath0
C_ath0.conf
 DEVICE IS DOWN ifname=ath0
ath0: Could not connect to kernel driver
Using interface ath0 with hwaddr a0:63:91:89:e6:45 and ssid 'NETGEAR65'
br0: port 3(ath0) entering forwarding state
Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
le: /etc/wpa2/WS DEVICE IS DOWN ifname=ath1
C_ath1.conf
 DEVICE IS DOWN ifname=ath1
ath1: Could not connect to kernel driver
Using interface ath1 with hwaddr a0:63:91:89:e6:47 and ssid 'NETGEAR65-5G'
br0: port 4(ath1) entering forwarding state
traffic_meter start : .
killall: igmpproxy: no process killed
ap-mode is on!!
_ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=85863380 arg=866a0000
 Scan in progress.. Cancelling it
br0: port 3(ath0) entering disabled state
br0: port 4(ath1) entering disabled state
Received SIGTERM
Entering released state
killall: minidlna: no process killed
killall: zcip: no process killed
killall: bpalogin: no process killed
NET: Unregistered protocol family 24
rmmod: ppp_generic: Resource temporarily unavailable
rmmod: slhc: Resource temporarily unavailable
Deleting static route ... Done!
Adding static route ... Done!
/etc/rc.common: /etc/rc.common: 117: /etc/init.d/leafp2p.sh: not found
rm: cannot remove '/etc/ppp/pppoe2-domain.conf': No such file or directory
rm: cannot remove '/etc/ppp/enable_ppp1': No such file or directory
Terminated
Stopping Firewall...
Done!
Deleting static route ... Done!
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
br0: port 5(eth1) entering forwarding state
The attached devices demo is Running ...
udhcp client (v0.9.8) started
Sending discover...
Jan  1 00:01:08 lld2d[3670]: osl_write_pidfile: /var/run/lld2d-br0.pid contains pid 910 which is still running; aborting

Jan  1 00:01:10 miniupnpd[3714]: listening on 169.254.126.231:5555
check minidlna ...
killall: minidlna: no process killed
configure auto-ip address ...
Running zcip -r 169.254.126.231 for br0
br0: starting userspace STP failed, starting kernel STP
time zone index is : 21
Run NTP Client with setting: pri:time-b.netgear.com sec:time-c.netgear.com
Jan  1 00:01:14 crond[3802]: crond 2.3.2 dillon, started, log level 8

killall: smbd: no process killed
killall: smbd: no process killed
killall: nmbd: no process killed

Enet:0 port:3 down
956x_GMAC:unit 0: phy 3 not up carrier 1
br0: topology change detected, propagating
br0: port 3(ath0) entering forwarding state
br0: topology change detected, propagating
br0: port 4(ath1) entering forwarding state
mtdoops: Attached to MTD device 13 name mtdoops
Boot up procedure is Finished!!!

Please press Enter to activate this console. br0: port 5(eth1) entering disabled state
br0: port 1(eth0) entering disabled state
config br0 169.254.126.231
IP address do not changed, exit

Enet:0 port3 up
956x_GMAC: Enet Unit:0 PHY:3 is UP eth0 SGMII 1000Mbps full duplex
956x_GMAC: done cfg2 0x7235 ifctl 0x0 miictrl
955x_SGMII::athr_gmac_sgmii_setup  Done
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: topology change detected, propagating
br0: port 5(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
The abbreviation of English is Eng!

Didn't find the language table we need!

Saving Data...
Done!

current version: 0, new version: 1000000259

Sending discover...

incorrect language table file, cannot find the region name.

configure auto-ip address ...
Running zcip -r 169.254.126.231 for br0
FILE: /tmp/uhttp-upgrade.img is download successfully!

config br0 169.254.126.231
IP address do not changed, exit
Writing Image             [#                        ]   4%
Writing Image             [##                       ]   8%
Writing Image             [###                      ]  12%
Writing Image             [####                     ]  16%
Writing Image             [#####                    ]  20%
Writing Image             [######                   ]  24%
Writing Image             [#######                  ]  28%
Writing Image             [########                 ]  32%
Writing Image             [#########                ]  36%
Writing Image             [##########               ]  40%
Writing Image             [###########              ]  44%
Writing Image             [############             ]  48%
Writing Image             [#############            ]  52%
Writing Image             [##############           ]  56%
Writing Image             [###############          ]  60%
Writing Image             [################         ]  64%
Writing Image             [#################        ]  68%
Writing Image             [##################       ]  72%
Writing Image             [###################      ]  76%
Writing Image             [####################     ]  80%
Writing Image             [#####################    ]  84%
Writing Image             [######################   ]  88%
Writing Image             [#######################  ]  92%
Writing Image             [######################## ]  96%
Writing Image             [#########################] 100%
Saving Data...
Done!

sh: /www/cgi-bin/uhttpd.sh: not found
Restarting system.
β–’β–’15β–’β–’50β–’β–’ iβ–’β–’a β–’β–’55β–’β–’
[    0.346970] printk: console [ttyS0] enabled
[    0.346970] printk: console [ttyS0] enabled
[    0.356036] printk: bootconsole [early0] disabled
[    0.356036] printk: bootconsole [early0] disabled
[    0.382666] spi-nand spi0.1: GigaDevice SPI NAND was found.
[    0.388438] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    0.399172] 2 fixed-partitions partitions found on MTD device (null)
[    0.405784] Creating 2 MTD partitions on "(null)":
[    0.410740] 0x000000000000-0x000000400000 : "kernel"
[    0.421613] 0x000000400000-0x000008000000 : "ubi"
[    0.580080] spi-nor spi0.0: mx25l1606e (2048 Kbytes)
[    0.585329] 8 fixed-partitions partitions found on MTD device spi0.0
[    0.591910] Creating 8 MTD partitions on "spi0.0":
[    0.596866] 0x000000000000-0x000000040000 : "u-boot"
[    0.604184] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.610559] 0x000000050000-0x000000060000 : "caldata_backup"
[    0.618790] 0x000000060000-0x000000070000 : "config"
[    0.624964] 0x000000070000-0x000000080000 : "traffic_meter"
[    0.633120] 0x000000080000-0x000000090000 : "pot"
[    0.638901] 0x000000090000-0x0000001f0000 : "reserved"
[    0.646643] 0x0000001f0000-0x000000200000 : "caldata"
[    1.345992] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[    2.003259] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    2.014551] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[    2.023602] NET: Registered protocol family 10
[    2.036409] Segment Routing with IPv6
[    2.040306] NET: Registered protocol family 17
[    2.045034] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.058426] 8021q: 802.1Q VLAN Support v1.8
[    2.066732] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[    2.073110]  MEM 0x0000000012000000..0x0000000013ffffff
[    2.078505]   IO 0x0000000000000000..0x0000000000000000
[    2.084095] PCI host bridge to bus 0000:00
[    2.088341] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    2.095472] pci_bus 0000:00: root bus resource [io  0x0000]
[    2.101226] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.108246] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.116484] pci 0000:00:00.0: [168c:abcd] type 00 class 0x020000
[    2.122734] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[    2.129790] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.136790] pci 0000:00:00.0: supports D1
[    2.140927] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.148075] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    2.154972] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x1201ffff 64bit]
[    2.162562] pci 0000:00:00.0: BAR 6: assigned [mem 0x12020000-0x1202ffff pref]
[    2.174114] UBI: auto-attach mtd1
[    2.177563] ubi0: attaching mtd1
[    2.264332] UBI: EOF marker found, PEBs from 28 will be erased
[    2.271166] ubi0: scanning is finished
[    2.309952] ubi0 warning: 0x8046a910: error -5 while erasing PEB 991, retry
[    2.317238] ubi0 warning: 0x8046a910: error -5 while erasing PEB 991, retry
[    2.324496] ubi0 warning: 0x8046a910: error -5 while erasing PEB 991, retry
[    2.331727] ubi0 error: 0x8046a934: cannot erase PEB 991, error -5
[    2.338132] CPU: 0 PID: 1 Comm: swapper Not tainted 5.10.138 #0
[    2.344245] Stack : 7fffefff 800bf368 807e0000 806d7688 00000000 00000000 00000000 00000000
[    2.352899]         00000000 00000000 00000000 00000000 00000000 00000001 80c2d900 21823573
[    2.361536]         80c2d998 00000000 00000000 80c2d7a8 00000038 80396424 00000000 ffffffea
[    2.370182]         00000072 80c2d7b4 00000072 80767a88 80c2d8e0 806a5d0c 00000000 00000000
[    2.378829]         806f646c 000003df 00005800 7fffefff 00000018 803fa67c 00000000 80920000
[    2.387484]         ...
[    2.390010] Call Trace:
[    2.390019] [<800bf368>] 0x800bf368
[    2.396145] [<80396424>] 0x80396424
[    2.399746] [<803fa67c>] 0x803fa67c
[    2.403355] [<8006697c>] 0x8006697c
[    2.406956] [<80066984>] 0x80066984
[    2.410559] [<8046a93c>] 0x8046a93c
[    2.414170] [<8046abc4>] 0x8046abc4
[    2.417773] [<8046b698>] 0x8046b698
[    2.421376] [<8046bba8>] 0x8046bba8
[    2.424984] [<8019494c>] 0x8019494c
[    2.428586] [<8046bfbc>] 0x8046bfbc
[    2.432196] [<80690280>] 0x80690280
[    2.435799] [<8046b020>] 0x8046b020
[    2.439400] [<80690280>] 0x80690280
[    2.443011] [<8046db3c>] 0x8046db3c
[    2.446614] [<801a30d4>] 0x801a30d4
[    2.450217] [<80466858>] 0x80466858
[    2.453827] [<80466488>] 0x80466488
[    2.457430] [<80468070>] 0x80468070
[    2.461029] [<801a2d70>] 0x801a2d70
[    2.464642] [<8045ea2c>] 0x8045ea2c
[    2.468243] [<80466c08>] 0x80466c08
[    2.471853] [<801a128c>] 0x801a128c
[    2.475456] [<804609b0>] 0x804609b0
[    2.479058] [<801a2a04>] 0x801a2a04
[    2.482675] [<80461f94>] 0x80461f94
[    2.486270] [<80466aa0>] 0x80466aa0
[    2.489873] [<8046de3c>] 0x8046de3c
[    2.493487] [<8046d868>] 0x8046d868
[    2.497087] [<8046ef64>] 0x8046ef64
[    2.500691] [<80462fbc>] 0x80462fbc
[    2.504298] [<800bf474>] 0x800bf474
[    2.507902] [<8080574c>] 0x8080574c
[    2.511503] [<8040972c>] 0x8040972c
[    2.515121] [<80805414>] 0x80805414
[    2.518725] [<807ef094>] 0x807ef094
[    2.522335] [<80060970>] 0x80060970
[    2.525937] [<800a231c>] 0x800a231c
[    2.529541] [<807efea4>] 0x807efea4
[    2.533149] [<807ef094>] 0x807ef094
[    2.536751] [<8068c888>] 0x8068c888
[    2.540354] [<8068c898>] 0x8068c898
[    2.543964] [<8068c888>] 0x8068c888
[    2.547565] [<80062178>] 0x80062178
[    2.551171]
[    2.552722] ubi0 error: 0x8046bcd4: failed to erase PEB 991, error -5
[    2.559367] ubi0: mark PEB 991 as bad
[    2.569314] nand: failed to write BBM to block @7fe0000 (err = -5)
[    2.575726] ubi0: 18 PEBs left in the reserve
[    2.626908] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 942 LEBs
[    2.634810] ubi0: attached mtd1 (name "ubi", size 124 MiB)
[    2.640485] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.647623] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.654651] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.661843] ubi0: good PEBs: 990, bad PEBs: 2, corrupted PEBs: 0
[    2.668042] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.675509] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1662173734
[    2.684941] ubi0: available PEBs: 0, total reserved PEBs: 991, PEBs reserved for bad PEB handling: 18
[    2.694560] ubi0: background thread "ubi_bgt0d" started, PID 335
[    2.712384] block ubiblock0_0: created from ubi0:0(rootfs)
[    2.718060] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    2.779709] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.793789] Freeing unused kernel memory: 1220K
[    2.798475] This architecture does not have kernel memory protection.
[    2.805158] Run /sbin/init as init process
[    4.096351] init: Console is alive
[    4.100310] init: - watchdog -
[    6.279632] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.548328] usbcore: registered new interface driver usbfs
[    6.554115] usbcore: registered new interface driver hub
[    6.559690] usbcore: registered new device driver usb
[    6.603493] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.623394] ehci-fsl: Freescale EHCI Host controller driver
[    6.638534] ehci-platform: EHCI generic platform driver
[    6.644331] ehci-platform 1b000000.usb: EHCI Host Controller
[    6.650201] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[    6.658443] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[    6.699282] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    6.714885] hub 1-0:1.0: USB hub found
[    6.724524] hub 1-0:1.0: 1 port detected
[    6.743867] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.772085] init: - preinit -
[    9.718722] random: jshn: uninitialized urandom read (4 bytes read)
[   10.128446] random: jshn: uninitialized urandom read (4 bytes read)
[   10.447594] random: jshn: uninitialized urandom read (4 bytes read)
[   10.806734] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.110004] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 4 is up
[   12.117972] eth0: link up (1000Mbps/Full duplex)
[   12.127689] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   12.134578] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   12.141669] random: procd: uninitialized urandom read (4 bytes read)
[   16.353882] UBIFS (ubi0:1): default file-system created
[   16.362286] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   16.372694] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 470
[   16.663483] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   16.671578] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   16.681858] UBIFS (ubi0:1): FS size: 118214656 bytes (112 MiB, 931 LEBs), journal size 5967872 bytes (5 MiB, 47 LEBs)
[   16.692819] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   16.699650] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID F598FC60-00FE-4B69-B6A9-B05B7D40119A, small LPT model
[   16.721852] mount_root: overlay filesystem has not been fully initialized yet
[   16.730213] mount_root: switching to ubifs overlay
[   16.747412] urandom-seed: Seed file not found (/etc/urandom.seed)
[   16.922288] eth0: link down
[   16.945041] procd: - early -
[   16.948334] procd: - watchdog -
[   17.799752] procd: - watchdog -
[   17.803589] procd: - ubus -
[   17.901066] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.909795] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.916942] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.933029] procd: - init -
Please press Enter to activate this console.
[   18.968537] random: jshn: uninitialized urandom read (4 bytes read)
[   19.033896] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.068821] kmodloader: loading kernel modules from /etc/modules.d/*
[   19.482414] urngd: v1.0.2 started.
[   19.521167] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   19.529045] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   19.776586] random: crng init done
[   19.780114] random: 24 urandom warning(s) missed due to ratelimiting
[   19.821299] ath9k 18100000.wmac: Direct firmware load for ath9k-eeprom-ahb-18100000.wmac.bin failed with error -2
[   19.831954] ath9k 18100000.wmac: Falling back to sysfs fallback for: ath9k-eeprom-ahb-18100000.wmac.bin
[   20.365724] ieee80211 phy0: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[   20.372866] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
[   20.386614] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
[   20.397087] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin
[   21.790675] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb2000000, irq=16
[   21.827251] kmodloader: done loading kernel modules from /etc/modules.d/*
[   79.730074] eth0: link up (1000Mbps/Full duplex)
[   79.745139] br-lan: port 1(eth0.1) entered blocking state
[   79.750728] br-lan: port 1(eth0.1) entered disabled state
[   79.756626] device eth0.1 entered promiscuous mode
[   79.761584] device eth0 entered promiscuous mode
[   79.771843] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   79.808748] br-lan: port 1(eth0.1) entered blocking state
[   79.814379] br-lan: port 1(eth0.1) entered forwarding state
[   80.931782] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
28

facing this all day long

C:\nmrp>nmrpflash -i net6 -f WNDR4300v2-V1.0.0.32.img
Waiting for Ethernet connection (Ctrl-C to skip).
Warning: IP address marked as deprecated.
Advertising NMRP server on net6 ... \pcap_sendpacket: send error: PacketSendPacket failed: The I/O operation failed because network media is disconnected or wireless access point is out of range.  (2150891551)
29

Netgear has written an NMRP server for Windows which probably would work better on a Windows machine than the third party one.

If you do use nmrpflash, it needs to be run in Administrator mode, and turn off all firewalls before running.

30

this same tool worked wonders yesterday, but still let me find the official NMRP server for windows.

31

Can't find the official NMRP tool but jclehner was kind enough to create a new version, but still

32

Got lucky a second time. Restored to factory firmware.
What is recommended to revert back to OpenWrt?
Flash openWrt using Nmrpflash or try with GUI method?

33

image
image1216Γ—906 30 KB

Finally back onto OpenWrt.
Bought a cheap Ethernet to USB dongle and it worked wonders.
Used nmrpflash-0.9.18.2-4-gb564180-win32.zip https://github.com/jclehner/nmrpflash/issues/112#issuecomment-1272345357
to flash back to Netgear firmware.
Flashed OpenWrt from the Web GUI https://openwrt.org/toh/netgear/wndr4300_v2#installation used factory image first.

https://downloads.openwrt.org/releases/22.03.1/targets/ath79/nand/openwrt-22.03.1-ath79-nand-netgear_wndr4300-v2-squashfs-factory.img
and then again with systemupgrade file to be on safe side.

https://downloads.openwrt.org/releases/22.03.1/targets/ath79/nand/openwrt-22.03.1-ath79-nand-netgear_wndr4300-v2-squashfs-sysupgrade.bin

Will IA, post a video on this process.

1 Like
34

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.