Version 21.2.02. I have an issue with the Ethernet ports on my Netgear WAC104. I have two wireless networks, LAN and GUEST and I want to run the GUEST network to my WAC104 from my WRT1900ACS. After I setup the VLANs on the WAC104, the port starts flapping with speed negotiations until it settles on 100FD or 10FD. This happens anywhere from a few minutes to four days after a reboot. If I remove the VLANs (and the bridge) the port is stable at 1000FD. (Edit: the problem occurs without a VLAN setup on the port, but at a reduced frequency.) I put a switch (configured for the VLANs) between the WAC104 and WRT1900ACS devices and the problem is with the WAC104, the WRT1900ACS port is stable with the VLANs setup. I have tried different cables and ports.
2022-03-30 03:09:44 Daemon.Notice 192.168.1.2 Mar 30 03:09:44 WAC104 netifd: Network device 'lan4' link is up
|2022-03-30 07:42:17|Daemon.Notice|192.168.1.2|Mar 30 07:42:17 WAC104 netifd: Network device 'lan4' link is up|
|2022-03-30 07:46:02|Kernel.Info|192.168.1.2|Mar 30 07:46:02 WAC104 kernel: [ 4755.651848] mt7530 mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control off|
|2022-03-30 07:46:02|Kernel.Info|192.168.1.2|Mar 30 07:46:02 WAC104 kernel: [ 4755.666480] br-lan: port 4(lan4) entered blocking state|
|2022-03-30 07:46:02|Kernel.Info|192.168.1.2|Mar 30 07:46:02 WAC104 kernel: [ 4755.676945] br-lan: port 4(lan4) entered forwarding state|
|2022-03-30 07:46:02|Daemon.Notice|192.168.1.2|Mar 30 07:46:02 WAC104 netifd: Network device 'lan4' link is up|
|2022-03-30 07:46:45|Kernel.Info|192.168.1.2|Mar 30 07:46:45 WAC104 kernel: [ 4798.659476] mt7530 mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control off|
|2022-03-30 07:46:45|Kernel.Info|192.168.1.2|Mar 30 07:46:45 WAC104 kernel: [ 4798.674164] br-lan: port 4(lan4) entered blocking state|
|2022-03-30 07:46:45|Kernel.Info|192.168.1.2|Mar 30 07:46:45 WAC104 kernel: [ 4798.684632] br-lan: port 4(lan4) entered forwarding state|
|2022-03-30 07:46:45|Daemon.Notice|192.168.1.2|Mar 30 07:46:45 WAC104 netifd: Network device 'lan4' link is up|
|2022-03-30 07:46:59|Daemon.Notice|192.168.1.2|Mar 30 07:46:59 WAC104 netifd: Network device 'lan4' link is up|
|2022-03-30 08:19:13|Kernel.Info|192.168.1.2|Mar 30 07:50:19 WAC104 kernel: [ 62.764587] mt7530 mdio-bus:1f lan4: Link is Up - 10Mbps/Full - flow control off|
|2022-03-30 08:19:13|Kernel.Info|192.168.1.2|Mar 30 07:50:19 WAC104 kernel: [ 62.779396] br-lan: port 4(lan4) entered blocking state|
|2022-03-30 08:19:13|Kernel.Info|192.168.1.2|Mar 30 07:50:19 WAC104 kernel: [ 62.789895] br-lan: port 4(lan4) entered forwarding state|
|2022-03-30 08:19:13|Daemon.Notice|192.168.1.2|Mar 30 07:50:19 WAC104 netifd: Network device 'lan4' link is up|