root@OpenWrt:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.167 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.3.0 r24106-10cc5fcd00) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Sep 23 12:34:46 2024
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys EA8500 WiFi Router
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s19788 r8192 d21172 u49152
[ 0.000000] pcpu-alloc: s19788 r8192 d21172 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=16
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 476468K/491520K available (6853K kernel code, 619K rwdata, 1088K rodata, 1024K init, 245K bss, 15052K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000025] Switching to timer-based delay loop, resolution 160ns
[ 0.000344] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000379] CPU: Testing write buffer coherency: ok
[ 0.000440] pid_max: default: 32768 minimum: 301
[ 0.001283] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001313] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003344] qcom_scm: convention: smc legacy
[ 0.004680] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.004880] rcu: Hierarchical SRCU implementation.
[ 0.005500] smp: Bringing up secondary CPUs ...
[ 0.007518] smp: Brought up 1 node, 2 CPUs
[ 0.007549] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.007567] CPU: All CPU(s) started in SVC mode.
[ 0.019804] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.019967] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020005] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.020279] pinctrl core: initialized pinctrl subsystem
[ 0.022448] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.022823] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.024371] thermal_sys: Registered thermal governor 'step_wise'
[ 0.026587] cpuidle: using governor ladder
[ 0.026662] cpuidle: using governor menu
[ 0.045492] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 0.078196] s1a: Bringing 0uV into 1050000-1050000uV
[ 0.078456] s1a: supplied by regulator-dummy
[ 0.078654] s1b: Bringing 0uV into 1050000-1050000uV
[ 0.078864] s1b: supplied by regulator-dummy
[ 0.079005] s2a: Bringing 0uV into 800000-800000uV
[ 0.079237] s2a: supplied by regulator-dummy
[ 0.079380] s2b: Bringing 0uV into 800000-800000uV
[ 0.079611] s2b: supplied by regulator-dummy
[ 0.080234] usbcore: registered new interface driver usbfs
[ 0.080301] usbcore: registered new interface driver hub
[ 0.080363] usbcore: registered new device driver usb
[ 0.080424] pps_core: LinuxPPS API ver. 1 registered
[ 0.080438] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.080472] PTP clock support registered
[ 0.082835] clocksource: Switched to clocksource dg_timer
[ 0.084140] NET: Registered PF_INET protocol family
[ 0.084334] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.085323] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.085363] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.085390] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.085427] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.085485] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.085582] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.085616] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.085932] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.085986] PCI: CLS 0 bytes, default 64
[ 0.087100] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.093810] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.093832] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.198133] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.202062] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[ 0.202367] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[ 0.202492] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.202834] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.202890] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.202943] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[ 0.202997] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[ 0.325746] qcom-pcie 1b500000.pci: iATU unroll: disabled
[ 0.325776] qcom-pcie 1b500000.pci: Detected iATU regions: 8 outbound, 8 inbound
[ 1.350442] qcom-pcie 1b500000.pci: Phy link never came up
[ 1.350635] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 1.350662] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.350691] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.350715] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 1.350742] pci_bus 0000:00: scanning bus
[ 1.350838] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 1.351000] pci 0000:00:00.0: supports D1
[ 1.351023] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.351052] pci 0000:00:00.0: PME# disabled
[ 1.355542] pci_bus 0000:00: fixups for bus
[ 1.355571] PCI: bus0: Fast back to back transfers disabled
[ 1.355597] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 1.355743] pci_bus 0000:01: scanning bus
[ 1.359717] pci_bus 0000:01: fixups for bus
[ 1.359730] PCI: bus1: Fast back to back transfers enabled
[ 1.359753] pci_bus 0000:01: bus scan returning with max=01
[ 1.359776] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 1.359802] pci_bus 0000:00: bus scan returning with max=ff
[ 1.359829] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.360100] pcieport 0000:00:00.0: assign IRQ: got 43
[ 1.360235] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43351a98
[ 1.361142] pcieport 0000:00:00.0: AER: enabled with IRQ 44
[ 1.361271] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 1.361295] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 1.361314] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 1.361332] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 1.361350] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 1.361369] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 1.361387] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 1.361404] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 1.361422] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0xfff0)
[ 1.361440] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 1.361457] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 1.361476] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 1.361493] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 1.361511] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 1.361529] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 1.361546] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3012b)
[ 1.362329] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[ 1.362623] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[ 1.362748] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[ 1.363204] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 1.363264] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 1.363316] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[ 1.363367] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[ 1.487529] qcom-pcie 1b700000.pci: iATU unroll: disabled
[ 1.487556] qcom-pcie 1b700000.pci: Detected iATU regions: 8 outbound, 8 inbound
[ 1.585265] qcom-pcie 1b700000.pci: Link up
[ 1.585457] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 1.585484] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.585514] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 1.585540] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 1.585564] pci_bus 0001:00: scanning bus
[ 1.585622] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 1.585768] pci 0001:00:00.0: supports D1
[ 1.585791] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 1.585817] pci 0001:00:00.0: PME# disabled
[ 1.590196] pci_bus 0001:00: fixups for bus
[ 1.590221] PCI: bus0: Fast back to back transfers disabled
[ 1.590246] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 1.590389] pci_bus 0001:01: scanning bus
[ 1.590607] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 1.590798] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.591640] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.591687] pci 0001:01:00.0: PME# disabled
[ 1.596265] pci_bus 0001:01: fixups for bus
[ 1.596324] PCI: bus1: Fast back to back transfers disabled
[ 1.596346] pci_bus 0001:01: bus scan returning with max=01
[ 1.596369] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 1.596394] pci_bus 0001:00: bus scan returning with max=ff
[ 1.596426] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 1.596463] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 1.596572] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 1.596601] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 1.596814] pcieport 0001:00:00.0: assign IRQ: got 45
[ 1.596944] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43351298
[ 1.597842] pcieport 0001:00:00.0: AER: enabled with IRQ 46
[ 1.597961] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 1.597985] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 1.598004] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 1.598023] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 1.598041] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 1.598058] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 1.598076] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 1.598094] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 1.598111] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[ 1.598128] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 1.598148] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 1.598164] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 1.598182] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 1.598199] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 1.598217] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 1.598235] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3012d)
[ 1.602352] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[ 1.602388] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[ 1.602700] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[ 1.602726] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[ 1.602948] krait-cc soc:clock-controller: L2 @ 384000 KHz
[ 1.608303] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 1.609832] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.612788] msm_serial 16340000.serial: msm_serial: detected port #0
[ 1.612855] msm_serial 16340000.serial: uartclk = 7372800
[ 1.612934] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 47, base_baud = 460800) is a MSM
[ 1.612987] msm_serial: console setup on port #0
[ 2.482235] printk: console [ttyMSM0] enabled
[ 2.487455] msm_serial: driver initialized
[ 2.496879] loop: module loaded
[ 2.498330] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 2.498829] nand: AMD/Spansion S34MS01G2
[ 2.505506] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.509484] 18 fixed-partitions partitions found on MTD device qcom_nand.0
[ 2.516816] Creating 18 MTD partitions on "qcom_nand.0":
[ 2.523627] 0x000000000000-0x000000040000 : "SBL1"
[ 2.529951] 0x000000040000-0x000000180000 : "MIBIB"
[ 2.535985] 0x000000180000-0x0000002c0000 : "SBL2"
[ 2.540801] 0x0000002c0000-0x000000540000 : "SBL3"
[ 2.547415] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 2.550152] 0x000000660000-0x000000780000 : "SSD"
[ 2.555376] 0x000000780000-0x000000a00000 : "TZ"
[ 2.562200] 0x000000a00000-0x000000c80000 : "RPM"
[ 2.567026] 0x000000c80000-0x000000dc0000 : "art"
[ 2.569641] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 2.574059] 0x000000ec0000-0x000000f00000 : "u_env"
[ 2.577894] 0x000000f00000-0x000000f40000 : "s_env"
[ 2.582532] 0x000000f40000-0x000000f80000 : "devinfo"
[ 2.587454] 0x000000f80000-0x000003780000 : "kernel1"
[ 2.649970] 0x000001380000-0x000003780000 : "rootfs1"
[ 2.702460] 0x000003780000-0x000005f80000 : "kernel2"
[ 2.761180] 0x000003b80000-0x000005f80000 : "rootfs2"
[ 2.814797] 0x000005f80000-0x000008000000 : "syscfg"
[ 2.912115] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 3.729494] ar8327: qca,phy-rgmii-en is not specified
[ 3.730431] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 3.733632] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 3.740865] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 3.747664] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.753691] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 3.761048] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 3.766968] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 3.774675] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 3.782485] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 3.788379] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 3.795753] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 3.802454] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 3.810092] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 3.817121] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.823281] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address ee:3b:d9:b9:3e:30
[ 3.834170] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 3.839610] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 3.847153] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 3.853736] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.859749] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 3.867305] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 3.873026] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 3.880752] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 3.888725] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 3.894545] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 3.901845] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 3.908684] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 3.916245] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 3.923274] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.929371] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address c2:27:fb:ad:06:d4
[ 3.940423] i2c_dev: i2c /dev entries driver
[ 3.949916] sdhci: Secure Digital Host Controller Interface driver
[ 3.950191] sdhci: Copyright(c) Pierre Ossman
[ 3.956276] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.969554] NET: Registered PF_INET6 protocol family
[ 3.971656] Segment Routing with IPv6
[ 3.973720] In-situ OAM (IOAM) with IPv6
[ 3.977278] NET: Registered PF_PACKET protocol family
[ 3.981224] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.986624] 8021q: 802.1Q VLAN Support v1.8
[ 3.999298] Registering SWP/SWPB emulation handler
[ 4.033253] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 4.045439] ubi0: attaching mtd16
[ 4.083213] random: crng init done
[ 4.312113] ubi0: scanning is finished
[ 4.321520] ubi0: attached mtd16 (name "rootfs2", size 36 MiB)
[ 4.321548] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.326299] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.333166] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.339957] ubi0: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0
[ 4.346787] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.352979] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1727094886
[ 4.360064] ubi0: available PEBs: 0, total reserved PEBs: 288, PEBs reserved for bad PEB handling: 20
[ 4.369558] ubi0: background thread "ubi_bgt0d" started, PID 93
[ 4.379122] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.384215] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.389823] clk: Disabling unused clocks
[ 4.400918] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.401637] Freeing unused kernel image (initmem) memory: 1024K
[ 4.407332] Run /sbin/init as init process
[ 4.412755] with arguments:
[ 4.412759] /sbin/init
[ 4.412763] with environment:
[ 4.412767] HOME=/
[ 4.412771] TERM=linux
[ 4.653499] init: Console is alive
[ 4.653664] init: - watchdog -
[ 4.655872] init: Watchdog has previously reset the system
[ 5.322598] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.391152] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.394473] SCSI subsystem initialized
[ 5.399951] libata version 3.00 loaded.
[ 5.401797] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 5.401939] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 5.408104] ahci 29000000.sata: supply target not found, using dummy regulator
[ 5.415098] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 5.421907] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 5.427420] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 5.437238] scsi host0: ahci
[ 5.444445] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 32
[ 5.775559] ata1: SATA link down (SStatus 0 SControl 300)
[ 5.777434] fsl-ehci: Freescale EHCI Host controller driver
[ 5.780437] ehci-platform: EHCI generic platform driver
[ 5.789084] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.790950] ohci-platform: OHCI generic platform driver
[ 5.928690] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.928736] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.933285] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 5.940659] xhci-hcd xhci-hcd.0.auto: irq 51, io mem 0x10000000
[ 5.950231] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.955970] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.961458] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 5.969508] hub 1-0:1.0: USB hub found
[ 5.975712] hub 1-0:1.0: 1 port detected
[ 5.979610] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.984505] hub 2-0:1.0: USB hub found
[ 5.991509] hub 2-0:1.0: 1 port detected
[ 5.995412] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.999136] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 6.004627] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 6.012004] xhci-hcd xhci-hcd.1.auto: irq 52, io mem 0x11000000
[ 6.021575] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 6.027325] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 6.032813] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 6.040852] hub 3-0:1.0: USB hub found
[ 6.047057] hub 3-0:1.0: 1 port detected
[ 6.050954] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.055317] hub 4-0:1.0: USB hub found
[ 6.062865] hub 4-0:1.0: 1 port detected
[ 6.067943] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.079555] init: - preinit -
[ 6.480510] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead.
[ 7.586218] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 7.586993] dwmac1000: Master AXI performs any burst length
[ 7.593450] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 7.608683] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 7.608810] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 7.617127] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 7.624043] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 7.632084] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 7.641276] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
[ 9.869581] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 9.869720] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 212
[ 9.924335] UBIFS (ubi0:1): recovery needed
[ 10.098827] UBIFS (ubi0:1): recovery completed
[ 10.098922] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 10.102161] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.110132] UBIFS (ubi0:1): FS size: 28061696 bytes (26 MiB, 221 LEBs), max 231 LEBs, journal size 1396736 bytes (1 MiB, 11 LEBs)
[ 10.120033] UBIFS (ubi0:1): reserved for root: 1325422 bytes (1294 KiB)
[ 10.131655] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D865B961-8D75-40E3-BB96-D49208D104CD, small LPT model
[ 10.138945] mount_root: overlay filesystem has not been fully initialized yet
[ 10.149829] mount_root: switching to ubifs overlay
[ 10.161325] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.211795] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 10.276510] procd: - early -
[ 10.276616] procd: - watchdog -
[ 10.278537] procd: Watchdog has previously reset the system
[ 10.815496] procd: - watchdog -
[ 10.815590] procd: Watchdog has previously reset the system
[ 10.881452] procd: - ubus -
[ 10.938466] procd: - init -
[ 11.276132] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.384557] Loading modules backported from Linux version v6.1.110-0-g5f55cad62cc9d
[ 11.384589] Backport generated by backports.git v6.1.110-1-0-g965f73fc
[ 11.446548] PPP generic driver version 2.4.2
[ 11.447106] NET: Registered PF_PPPOX protocol family
[ 11.462261] ath10k_pci 0001:01:00.0: assign IRQ: got 45
[ 11.462288] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x40.
[ 11.462773] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 11.469230] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 11.469598] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43351298
[ 11.469727] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.603194] urngd: v1.0.2 started.
[ 11.923454] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead.
[ 12.322270] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 12.322313] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 12.332254] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf
[ 12.403066] ath10k_pci 0001:01:00.0: Loading BDF type 0
[ 12.404692] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 4a3d27bf
[ 13.561259] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 13.561297] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 13.637188] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 13.637930] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
[ 13.907975] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 13.997077] ath: EEPROM regdomain: 0x0
[ 13.997087] ath: EEPROM indicates default country code should be used
[ 13.997092] ath: doing EEPROM country->regdmn map search
[ 13.997098] ath: country maps to regdmn code: 0x3a
[ 13.997103] ath: Country alpha2 being used: US
[ 13.997108] ath: Regpair used: 0x3a
[ 14.046504] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.162457] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead.
[ 25.979474] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 25.980251] dwmac1000: Master AXI performs any burst length
[ 25.986725] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 26.001942] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 26.002080] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 26.009885] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 26.017267] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 26.023250] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 26.042858] br-lan: port 1(eth1.1) entered blocking state
[ 26.042895] br-lan: port 1(eth1.1) entered disabled state
[ 26.047540] device eth1.1 entered promiscuous mode
[ 26.052632] device eth1 entered promiscuous mode
[ 26.065212] br-lan: port 1(eth1.1) entered blocking state
[ 26.065247] br-lan: port 1(eth1.1) entered forwarding state
[ 26.082690] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 26.083578] dwmac1000: Master AXI performs any burst length
[ 26.089856] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 26.105251] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 26.105522] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 26.124511] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 26.124825] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 26.148376] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.033228] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 92.138204] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 92.138279] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 92.214247] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 92.214981] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
[ 92.573816] ath10k_pci 0001:01:00.0: rts threshold -1
[ 92.574310] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 92.579540] br-lan: port 2(phy0-ap0) entered blocking state
[ 92.588873] br-lan: port 2(phy0-ap0) entered disabled state
[ 92.594531] device phy0-ap0 entered promiscuous mode
[ 92.599886] br-lan: port 2(phy0-ap0) entered blocking state
[ 92.605103] br-lan: port 2(phy0-ap0) entered forwarding state
[ 92.610827] br-lan: port 2(phy0-ap0) entered disabled state
[ 92.617820] device phy0-ap0 left promiscuous mode
[ 92.621640] br-lan: port 2(phy0-ap0) entered disabled state
[ 92.655456] br-lan: port 2(phy0-ap0) entered blocking state
[ 92.655487] br-lan: port 2(phy0-ap0) entered disabled state
[ 92.660049] device phy0-ap0 entered promiscuous mode
[ 92.817272] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 100.597610] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
[ 100.597778] br-lan: port 2(phy0-ap0) entered blocking state
[ 100.603030] br-lan: port 2(phy0-ap0) entered forwarding state
[ 152.373223] ath10k_pci 0001:01:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0 arvif->paused: 0x0
