I have successfully installed openwrt on my other mi rouer 4a gigabit but this one always bootloops and stuck at orange light, I have tried using mi wifi repair tool and it doesn't work, also tried tinypxe. I have tried connecting the router via serial port and it only shows this on loop from recovery mode:
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=107) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=107) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=107) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=49952, dst=51007, len=144) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=130) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=274) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=52053, dst=1900, len=170) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=274) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=40) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=40) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=52053, dst=1900, len=170) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=40) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=40) state: 3
Filtering pkt = -1
BOOTP broadcast 2
DHCPHandler: got packet: (src=5353, dst=5353, len=130) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=274) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=49952, dst=51007, len=144) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=40) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=40) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=6771, dst=6771, len=137) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=5353, dst=5353, len=274) state: 3
Filtering pkt = -1
DHCPHandler: got packet: (src=49952, dst=51007, len=144) sta
and the serial output on stuck orange light is looping this:
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW
restore_defaults:<NULL>
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
n3: System Boot system code via Flash.
Booting System 1
## Booting image at bc180000 ...
Bad Magic Number,504B0304, try to reboot
Erasing SPI Flash...
raspi_erase: offs:ff0000 len:10000
.
Writing to SPI Flash...
.
done
===================================================================
MT7621 stage1 code Mar 26 2019 09:44:48 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
==================================================================
SPI-NOR flash has JEDEC ID: ef4018
Status Register 1 = 0x00
Status Register 3 = 0x68
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL4 FB_DL: 0x6, 1/0 = 558/466 19000000
PLL3 FB_DL: 0xd, 1/0 = 614/410 35000000
PLL2 FB_DL: 0x13, 1/0 = 659/365 4D000000
If any one of you could be so kind to assist me in fixing this or point me to a correct tutorial to follow in how to fix this