Lost connection pppoe Luci 19.07

Hi
For some time now, several times a day, my pppoe connection breaks down and cannot be re-established. I have contacted isp but everything is ok on their side. Does anyone have a similar problem? Netgear R6220 router. I would appreciate your help. thanks

post the dmesg (or kernel, as it's called in the web interface) log.

[    0.000000] Linux version 4.14.221 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11306-c4a6851c72)) #0 SMP Mon Feb 15 15:22:37 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Netgear R6220
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 805747c0, node_mem_map 81003000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from 0x80577744 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344
[    0.000000] pcpu-alloc: s26224 r8192 d22928 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000008
[    0.000000] Readback ErrCtl register=00000008
[    0.000000] Memory: 122620K/131072K available (4756K kernel code, 239K rwdata, 588K rodata, 1252K init, 255K bss, 8452K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000010] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015497] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087796] pid_max: default: 32768 minimum: 301
[    0.097091] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110108] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125643] Hierarchical SRCU implementation.
[    0.134903] smp: Bringing up secondary CPUs ...
[    0.155548] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.155557] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.155567] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.155695] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204377] Synchronize counters for CPU 1: done.
[    0.264034] smp: Brought up 1 node, 2 CPUs
[    0.275663] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.295137] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.307340] pinctrl core: initialized pinctrl subsystem
[    0.319068] NET: Registered protocol family 16
[    0.334487] FPU Affinity set after 11720 emulations
[    0.335353] pull PCIe RST: RALINK_RSTCTRL = 0
[    0.644286] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.654360] ***** Xtal 40MHz *****
[    0.661082] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.671290] Port 0 N_FTS = 1b102800
[    0.678184] Port 1 N_FTS = 1b102800
[    0.685109] Port 2 N_FTS = 1b102800
[    1.843330] PCIE1 no card, disable it(RST&CLK)
[    1.852020]  -> 12007f2
[    1.856839] PCIE0 enabled
[    1.862035] PCIE2 enabled
[    1.867217] PCI host bridge /pcie@1e140000 ranges:
[    1.876744]  MEM 0x0000000060000000..0x000000006fffffff
[    1.887098]   IO 0x000000001e160000..0x000000001e16ffff
[    1.897470] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    1.923170] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.934526] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.945780] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.958790] PCI host bridge to bus 0000:00
[    1.966884] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.980492] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.992220] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.005697] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.021476] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    2.021515] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.021527] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    2.021593] pci 0000:00:00.0: supports D1
[    2.021602] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.021889] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    2.021925] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.021942] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    2.022013] pci 0000:00:01.0: supports D1
[    2.022025] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    2.022323] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.038128] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.054230] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[    2.054297] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    2.054355] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.054466] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    2.054662] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.054916] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[    2.054972] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[    2.055119] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    2.055308] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    2.055331] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[    2.055411] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.068460] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.082266] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.095387] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.109215] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.122701] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.137035] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.150511] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[    2.164001] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[    2.177478] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.192004] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.206327] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.216159] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.229661] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.244005] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[    2.257476] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.267312] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.282580] clocksource: Switched to clocksource GIC
[    2.293808] NET: Registered protocol family 2
[    2.303337] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.317091] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    2.329693] TCP: Hash tables configured (established 1024 bind 1024)
[    2.342407] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.353914] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.366536] NET: Registered protocol family 1
[    2.375126] PCI: CLS 0 bytes, default 32
[    2.612532] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.623610] Crashlog allocated RAM at address 0x3f00000
[    2.634124] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    2.655253] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.666757] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.689823] io scheduler noop registered
[    2.697626] io scheduler deadline registered (default)
[    2.708798] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.725393] console [ttyS0] disabled
[    2.732410] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 15, base_baud = 3125000) is a 16550A
[    2.750405] console [ttyS0] enabled
[    2.764174] bootconsole [early0] disabled
[    2.782310] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    2.796519] Enable NFI Clock
[    2.802243] # MTK NAND # : Use HW ECC
[    2.809558] Device not found, ID: c2f1
[    2.817019] Not Support this Device! 
[    2.824486] chip_mode=00000001
[    2.830550] Support this Device in MTK table! c2f1 
[    2.840438] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[    2.853313] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[    2.865965] nand: Macronix NAND 128MiB 3,3V 8-bit
[    2.875331] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.890419] Scanning device for bad blocks
[    3.140200] 6 fixed-partitions partitions found on MTD device MT7621-NAND
[    3.153716] Creating 6 MTD partitions on "MT7621-NAND":
[    3.164130] 0x000000000000-0x000000100000 : "u-boot"
[    3.175130] 0x000000100000-0x000000200000 : "SC PID"
[    3.186060] 0x000000200000-0x000000600000 : "kernel"
[    3.197085] 0x000000600000-0x000002200000 : "ubi"
[    3.207691] 0x000002e00000-0x000002f00000 : "factory"
[    3.218797] 0x000004200000-0x000007e00000 : "reserved"
[    3.230575] [mtk_nand] probe successfully!
[    3.239454] Signature matched and data read!
[    3.247959] load_fact_bbt success 1023
[    3.256177] libphy: Fixed MDIO Bus: probed
[    3.335144] libphy: mdio: probed
[    4.741217] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    4.753745] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 17
[    4.773373] NET: Registered protocol family 10
[    4.783837] Segment Routing with IPv6
[    4.791211] NET: Registered protocol family 17
[    4.800180] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.825971] 8021q: 802.1Q VLAN Support v1.8
[    4.837449] UBI: auto-attach mtd3
[    4.844139] ubi0: attaching mtd3
[    4.977071] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[    5.118202] ubi0: scanning is finished
[    5.140628] ubi0: attached mtd3 (name "ubi", size 28 MiB)
[    5.151422] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.165117] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.178636] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.192497] ubi0: good PEBs: 224, bad PEBs: 0, corrupted PEBs: 0
[    5.204460] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    5.218846] ubi0: max/mean erase counter: 21/6, WL threshold: 4096, image sequence number: 1514313493
[    5.237204] ubi0: available PEBs: 0, total reserved PEBs: 224, PEBs reserved for bad PEB handling: 20
[    5.255593] ubi0: background thread "ubi_bgt0d" started, PID 362
[    5.257436] block ubiblock0_0: created from ubi0:0(rootfs)
[    5.278526] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    5.292394] hctosys: unable to open rtc device (rtc0)
[    5.302737] usb_vbus: disabling
[    5.315400] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.333854] Freeing unused kernel memory: 1252K
[    5.342926] This architecture does not have kernel memory protection.
[    5.454111] random: fast init done
[    5.816854] init: Console is alive
[    5.823907] init: - watchdog -
[    6.349564] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[    6.438401] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.553318] usbcore: registered new interface driver usbfs
[    6.564373] usbcore: registered new interface driver hub
[    6.575076] usbcore: registered new device driver usb
[    6.592302] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    6.610044] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.620691] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    6.642720] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[    6.661007] xhci-mtk 1e1c0000.xhci: irq 16, io mem 0x1e1c0000
[    6.673529] hub 1-0:1.0: USB hub found
[    6.681066] hub 1-0:1.0: 2 ports detected
[    6.689749] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.700410] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    6.715340] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0  SuperSpeed
[    6.728340] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    6.745379] hub 2-0:1.0: USB hub found
[    6.752947] hub 2-0:1.0: 1 port detected
[    6.765947] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.782947] init: - preinit -
[    6.997900] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
[    7.510500] mtk_soc_eth 1e100000.ethernet: PPE started
[    7.601917] random: procd: uninitialized urandom read (4 bytes read)
[    8.102592] usb 1-2: new high-speed USB device number 2 using xhci-mtk
[   10.748153] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 466
[   10.820929] UBIFS (ubi0:1): recovery needed
[   11.026069] UBIFS (ubi0:1): recovery completed
[   11.035079] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.050672] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.070417] UBIFS (ubi0:1): FS size: 21458944 bytes (20 MiB, 169 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs)
[   11.091016] UBIFS (ubi0:1): reserved for root: 1013558 bytes (989 KiB)
[   11.104083] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 5B9C47DD-A33E-4096-8100-842BF08A6323, small LPT model
[   11.139443] mount_root: loading kmods from internal overlay
[   11.376091] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   11.601246] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.650374] SCSI subsystem initialized
[   11.670427] ehci-platform: EHCI generic platform driver
[   11.694823] usb-storage 1-2:1.0: USB Mass Storage device detected
[   11.707565] scsi host0: usb-storage 1-2:1.0
[   11.716710] usbcore: registered new interface driver usb-storage
[   11.729112] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   11.895444] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   11.917019] block: extroot: not configured
[   11.966452] mount_root: switching to ubifs overlay
[   11.999280] urandom-seed: Seeding with /etc/urandom.seed
[   12.186093] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[   12.210073] procd: - early -
[   12.215959] procd: - watchdog -
[   12.734581] scsi 0:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 4
[   12.753726] sd 0:0:0:0: [sda] 30433280 512-byte logical blocks: (15.6 GB/14.5 GiB)
[   12.769608] sd 0:0:0:0: [sda] Write Protect is off
[   12.779171] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[   12.779927] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   12.803240]  sda: sda1
[   12.812895] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   13.312880] procd: - watchdog -
[   13.319866] procd: - ubus -
[   13.408763] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.428672] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.441989] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.456250] procd: - init -
[   14.510212] kmodloader: loading kernel modules from /etc/modules.d/*
[   14.620368] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.638377] Netfilter messages via NETLINK v0.30.
[   14.655728] ip_set: protocol 6
[   14.749263] Bridge firewalling registered
[   14.759187] Loading modules backported from Linux version v4.19.161-0-gdaefdc9eb24b
[   14.774533] Backport generated by backports.git v4.19.161-1-0-g4bb568fe
[   14.790927] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.798421] urngd: v1.0.2 started.
[   14.809118] MRM The MAC Address Re-Mapper is now in the kernel
[   14.830087] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   14.902506] xt_time: kernel timezone is -0000
[   15.023464] random: crng init done
[   15.030291] random: 6 urandom warning(s) missed due to ratelimiting
[   15.058427] bus=0x2, slot = 0x1, irq=0xff
[   15.066548] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[   15.078016] mt7603e 0000:02:00.0: ASIC revision: 76030010
[   16.094665] EXT4-fs (sda1): recovery complete
[   16.112953] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: 
[   16.114301] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[   16.138452] mt7603e 0000:02:00.0: Build Time: 20160107100755
[   16.182672] mt7603e 0000:02:00.0: firmware init done
[   16.359548] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.377951] bus=0x1, slot = 0x0, irq=0xff
[   16.386041] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[   16.397635] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   17.119523] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   17.135323] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   17.146292] mt76x2e 0000:01:00.0: Build: 1
[   17.154451] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   17.182585] mt76x2e 0000:01:00.0: Firmware running!
[   17.195150] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   17.206723] PPP generic driver version 2.4.2
[   17.216856] NET: Registered protocol family 24
[   17.229200] kmodloader: done loading kernel modules from /etc/modules.d/*
[   25.123032] mtk_soc_eth 1e100000.ethernet: PPE started
[   25.138961] br-lan: port 1(eth0.1) entered blocking state
[   25.149887] br-lan: port 1(eth0.1) entered disabled state
[   25.161279] device eth0.1 entered promiscuous mode
[   25.170991] device eth0 entered promiscuous mode
[   25.183541] br-lan: port 1(eth0.1) entered blocking state
[   25.194386] br-lan: port 1(eth0.1) entered forwarding state
[   25.205993] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   26.220433] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.003541] pppoe-wan: renamed from ppp0
[   28.863313] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   28.912210] br-lan: port 2(wlan0) entered blocking state
[   28.922930] br-lan: port 2(wlan0) entered disabled state
[   28.934160] device wlan0 entered promiscuous mode
[   28.943856] br-lan: port 2(wlan0) entered blocking state
[   28.954519] br-lan: port 2(wlan0) entered forwarding state
[   29.455888] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   29.484406] br-lan: port 3(wlan1) entered blocking state
[   29.495173] br-lan: port 3(wlan1) entered disabled state
[   29.506283] device wlan1 entered promiscuous mode
[   29.515878] br-lan: port 3(wlan1) entered blocking state
[   29.526530] br-lan: port 3(wlan1) entered forwarding state
[   29.540689] br-lan: port 2(wlan0) entered disabled state
[   29.579912] br-lan: port 3(wlan1) entered disabled state
[   33.156310] pppoe-wan: renamed from ppp0
[   39.031319] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   39.044463] br-lan: port 2(wlan0) entered blocking state
[   39.055121] br-lan: port 2(wlan0) entered forwarding state
[  111.790300] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  111.803696] br-lan: port 3(wlan1) entered blocking state
[  111.814350] br-lan: port 3(wlan1) entered forwarding state