Looking for someone with Linksys EA3500

I prepare 6.1 bump for kirkwood target:

I need to see u-boot envs for EA3500. Could someone paste fw_printenv command result?

@onefreeman @builder
Maybe you can help?

I found this in an older mail-discussion. Does this help?

bootdelay=0
 baudrate=115200
 loads_echo=0
 ipaddr=192.168.1.10
 serverip=192.168.1.254
 rootpath=/mnt/ARM_FS
 netmask=255.255.255.0
 run_diag=yes
 stdin=serial
 stdout=serial
 stderr=serial
 console=console=ttyS0,115200
 badcount=0
 bootbadcount=0
 uenvbadcount=0
 senvbadcount=0
 buffbadcount=0
 fs_bootargs=unused
 
mtdparts=mtdparts=nand_mtd:512k(uboot)ro,16k@512k(u_env),16k@528k(s_env),20m@2m(kernel),20m@2m(rootfs)fs,20m@2
 2m(alt_kernel),20m@22m(alt_rootfs)fs,22m@42m(syscfg)
 
mfg_mtdparts=mtdparts=nand_mtd:512k(uboot)ro,16k@512k(u_env),16k@528k(s_env),20m@2m(kernel),20m@2m(rootfs)fs,2
 
0m@22m(alt_kernel),20m@22m(alt_rootfs)fs,20m@42m(mfg_kernel),20m@42m(mfg_rootfs)fs,2m@62m(syscfg)
 mainlineLinux=no
 enaMonExt=no
 enaCpuStream=no
 enaWrAllo=no
 pexMode=RC
 disL2Cache=no
 setL2CacheWT=yes
 disL2Prefetch=yes
 enaICPref=yes
 enaDCPref=yes
 sata_dma_mode=yes
 ethprime=egiga0
 netbsd_en=no
 vxworks_en=no
 bootargs_root=root=/dev/nfs rw
 fs_bootargs_root=root=/dev/mtdblock4 ro rootfstype=jffs2
 alt_fs_bootargs_root=root=/dev/mtdblock6 ro rootfstype=jffs2
 mfg_fs_bootargs_root=root=/dev/mtdblock8 ro rootfstype=jffs2
 usb_fs_bootargs_root=root=/dev/sda1 rw rootfstype=ext2
 bootargs_end=:::DB88FXX81:eth0:none
 image_name=uImage
 bootcmd=run nandboot
 nfsboot=tftp 0x2000000 uImage; setenv bootargs $(console) $(mfg_mtdparts)
 $(bootargs_root) nfsroot=$(serverip)        :$(rootpath)
 ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000;
 nandboot=nand read.e 0x2000000 0x200000 0x300000; setenv bootargs
 $(console) $(mtdparts) $(fs_bootargs_root) s        erial_number=$(sn)
 uuid=$(uuid) hw_version=$(hw) device_mac=$(mac) factory_date=$(date)
 wps_pin=$(wps); bootm         0x2000000;
 altnandboot=nand read.e 0x2000000 0x1600000 0x300000; setenv bootargs
 $(console) $(mtdparts) $(alt_fs_bootargs        _root) serial_number=$(sn)
 uuid=$(uuid) hw_version=$(hw) device_mac=$(mac) factory_date=$(date)
 wps_pin=$(wps)        ; bootm 0x2000000;
 mfgboot=nand read.e 0x2000000 0x2a00000 0x300000; setenv bootargs
 $(console) $(mfg_mtdparts) $(mfg_fs_bootargs        _root)
 serial_number=$(sn) uuid=$(uuid) hw_version=$(hw) device_mac=$(mac)
 factory_date=$(date) wps_pin=$(wps)        ; bootm 0x2000000;
 usbboot=usb start;ext2load usb 0:1 2000000 /uImage; setenv bootargs
 $(console) $(mtdparts) $(usb_fs_bootargs_r        oot) rootdelay=10; bootm
 0x2000000;
 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console)
 root=/dev/mtdblock0 rw ip=$(ipaddr):$(ser        verip)$(bootargs_end)
 $(mvPhoneConfig); bootm 0x2000000;
 lcd0_enable=0
 lcd0_params=640x480-16@60
 disaMvPnp=no
 ethaddr=00:50:43:00:02:02
 ethmtu=1500
 eth1addr=00:50:43:00:02:02
 eth1mtu=1500
 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
 mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
 usb0Mode=host
 yuk_ethaddr=00:00:00:EE:51:81
 nandEcc=1bit
 netretry=no
 rcvrip=169.254.100.100
 loadaddr=0x02000000
 autoload=no
 image_multi=yes
 enaAutoRecovery=yes
 mtdparts_version=2
 envsaved=yes
 auto_recovery=yes

Yes. Thank you.

1 Like

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.