Linksys WRT160NL or E2100L fulldump or bootloader

I have a WRT160NL which has a kernel panic in the serial console on stock firmware. After flashing to some versions of openwrt, I have some others errors in the serial console, and stuck or reboot after its.
I replaced the RAM with 64MB and checked the flash in the programmer, so there is no problem with it.
I flash bootloader breed it works but no firmware starts correctly because breed only supports TP-link and Atheros SDK
I think I need a flash fulldump to flash IC
Linksys support does not have full dump or bootloader files

don't think breed cares much about what it's booting, as long as it (breed) starts, you should be OK.

what errors are you getting through the serial console ?

## Booting WRT160NL ...
Application code length 0x0000ffe0
CRC OK
## Booting image at bf04003c ...
   Image Name:   MIPS OpenWrt Linux-2.6.32.25
   Created:      2010-11-20   4:30:14 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1235035 Bytes =  1.2 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
kernel: org len = 1235035, new len = 1245184
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 1                                                                                        9 20:27:50 PST 2010
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR9130 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,1152                                                                                        00 board=WRT160NL
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 61716k/65536k available (2113k kernel code, 3744k reserved, 395k data, 1                                                                                        52k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is Linksys WRT160NL
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
do_cpu invoked from kernel context![#1]:
Cpu 0
$ 0   : 00000000 0000006d 00000000 00000001
$ 4   : 83867108 00000000 00000000 83806120
$ 8   : 83801e24 000000e0 83819d08 83868b00
$12   : 00000000 00000000 00000400 00000400
$16   : 00000000 83867108 802fa000 83868a80
$20   : 00000000 00000000 00000000 00000000
$24   : 00000000 40000000
$28   : 83818000 83819e18 00000000 80172ed0
Hi    : 00000001
Lo    : 00000007
epc   : 83801ee0 0x83801ee0
    Not tainted
ra    : 80172ed0 0x80172ed0
Status: 1000c003    KERNEL EXL IE
Cause : 1080002c
PrId  : 00019374 (MIPS 24Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=83818000, task=83814000, tls=00000000)
Stack : 83868900 fffffff4 83868880 83868a80 83819e40 83867100 00000000 801aafc4
        00000000 800dc824 80286dc4 801aaf1c 83868a80 fffffff4 80286dc4 802fa000
        00000000 801ab134 00000000 802f8928 802f8b28 802e3d08 802f8928 802f8b28
        802e3d08 00000000 00000000 802e3d90 00000000 00000000 83868780 802e15f4
        8027cdf0 802e0ba4 802f8924 802f8928 802f8b28 802e3d08 00000000 00000000
        ...
Call Trace:[<801aafc4>] 0x801aafc4
[<800dc824>] 0x800dc824
[<801aaf1c>] 0x801aaf1c
[<801ab134>] 0x801ab134
[<802e3d08>] 0x802e3d08
[<802e3d08>] 0x802e3d08
[<802e3d90>] 0x802e3d90
[<802e15f4>] 0x802e15f4
[<802e0ba4>] 0x802e0ba4
[<802e3d08>] 0x802e3d08
[<8006a710>] 0x8006a710
[<800ab000>] 0x800ab000
[<802e5894>] 0x802e5894
[<802d433c>] 0x802d433c
[<8006c8cc>] 0x8006c8cc
[<802d426c>] 0x802d426c
[<8006c8bc>] 0x8006c8bc


Code: 83801ed0  00000000  83807100 <00000001> 00000000  00000003  00000000  0000                                                                                        0000  00000000
Disabling lock debugging due to kernel taint
Kernel panic - not syncing: Attempted to kill init!

that's a 12 years OS booting, and crashing, probably unrelated to Breed.

Breeed not load any OS, its result with stock uboot.
And with new openwrt. I think, problem in hardware. Maybe some MCU (wifi module as example) not works

## Booting WRT160NL ...
Application code length 0x0015699c
CRC OK
## Booting image at bf04003c ...
   Image Name:   MIPS OpenWrt Linux-4.4.14
   Created:      2017-11-04  21:15:13 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1403199 Bytes =  1.3 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
kernel: org len = 1403199, new len = 1441792
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...



OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80060000...

[    0.000000] Linux version 4.4.14 (buildbot@owrtbuild01) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 12009) ) #1 Wed Dec 6 23:56:36 UTC 2017
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9130 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] No valid device tree found, continuing without
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]

...and not loading more

could be hw gone bad, but I still don't think a full flash dump will get you any further.