I would try the initramfs kernel bin, but that's unlikely to work from the web interface.
What's happening is clear, there's rt1800 and e7350 out there with corrupted boot partition 1 that only boot from partition 2.
Connecting UART allows the uboot to finally format the partition 1 allowing openwrt to install.
Sounds like I'm going to have to open up it up after all then.
Success!! 
Had to dive into the unit and hook up an serial cable to select uploading the firmware via tftp. The -kernel.bin was the only firmware which was able to boot properly. From there, I was able to SCP a custom -sysupgrade.bin with luci and install it via sysupgrade from SSH. The radios seem to be working properly (at least the 5 Ghz) which is the only one I need to run the unit in Client Mode.
Damn, I went through gthe exact same thing you did with the exact same base version and unsigned version.
I read this and picked one up as I assumed it would get official support soon:
ramips: add support for Linksys E7350 by neheb · Pull Request #4470 · openwrt/openwrt · GitHub
Wonder if I should wait it out or just return it...
It’s already merged. Just flash a snapshot build
I had the same issue as bliss.
Tried all 3 snapshot options from here:
OpenWrt Firmware Selector
snapshot image radio can not work I tried already.
Were there any error messages in dmesg?
No here is full booting log.
U-Boot 2018.09-svn862 (Aug 04 2020 - 17:52:35 +0800)
CPU: MediaTek MT7621AT ver 1, eco 3
Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz
Model: MediaTek MT7621 reference board (NAND)
DRAM: 256 MiB
NAND: 128 MiB
Loading Environment from NAND... OK
In: uartlite0@1e000c00
Out: uartlite0@1e000c00
Err: uartlite0@1e000c00
Net:
Warning: eth@1e100000 (eth0) using random MAC address - 5e:86:f9:ce:9e:b1
eth0: eth@1e100000
Hit any key to stop autoboot: 0
*** U-Boot Boot Menu *** Press UP/DOWN to move, ENTER to select 1. Startup system (Default) 2. Upgrade firmware 3. Upgrade bootloader 4. Upgrade bootloader (advanced mode) 5. Load image 6. Upgrade firmware with code pattern 0. U-Boot console Hit any key to stop autoboot: 3 2 Saving Environment to NAND... Erasing NAND...
Erasing at 0x80000 -- 100% complete.
Writing to NAND... OK
OK
#####CBT_BOOT_VERSION=[V0.2]######
#####boot_count=[1] boot_part=[2] boot_change=[0]######
Loading from nand0, offset 0x3180000
Fit image detected...
FIT description: MIPS OpenWrt FIT (Flattened Image Tree)
Image 0 (kernel-1)
Description: MIPS OpenWrt Linux-5.10.166
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x800100e4
Data Size: 2859345 Bytes = 2.7 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Hash algo: crc32
Hash value: 8b672671
Hash algo: sha1
Hash value: 7153fb1177a0b087c4742d419cdf9212bc39aa09
Image 1 (fdt-1)
Description: MIPS OpenWrt linksys_e7350 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x802ca374
Data Size: 10468 Bytes = 10.2 KiB
Architecture: MIPS
Hash algo: crc32
Hash value: b793cf8c
Hash algo: sha1
Hash value: c8c0cba37bde8383bf157394343ff29dce87e246
Default Configuration: 'config-1'
Configuration 0 (config-1)
Description: OpenWrt linksys_e7350
Kernel: kernel-1
FDT: fdt-1
Automatic boot of image at addr 0x80010000 ...
## Loading kernel from FIT Image at 80010000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.166
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x800100e4
Data Size: 2859345 Bytes = 2.7 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Hash algo: crc32
Hash value: 8b672671
Hash algo: sha1
Hash value: 7153fb1177a0b087c4742d419cdf9212bc39aa09
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 80010000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: MIPS OpenWrt linksys_e7350 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x802ca374
Data Size: 10468 Bytes = 10.2 KiB
Architecture: MIPS
Hash algo: crc32
Hash value: b793cf8c
Hash algo: sha1
Hash value: c8c0cba37bde8383bf157394343ff29dce87e246
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x802ca374
Uncompressing Kernel Image ... OK
Loading Device Tree to 8fe77000, end 8fe7c8e3 ... OK
[ 0.000000] Linux version 5.10.166 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.2.0 r22000-6bc675c0be) 12.2.0, GNU ld (GNU Binutils) 2.39) #0 SMP Sun Feb 5 21:39:17 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Linksys E7350
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00020430
[ 0.000000] Readback ErrCtl register=00020430
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 248708K/262144K available (7032K kernel code, 630K rwdata, 1416K rodata, 1276K init, 243K bss, 13436K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.007945] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.016992] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.083148] pid_max: default: 32768 minimum: 301
[ 0.087916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.095118] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105756] rcu: Hierarchical SRCU implementation.
[ 0.110800] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.118938] smp: Bringing up secondary CPUs ...
[ 0.124210] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.124222] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.124233] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.124307] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.178682] Synchronize counters for CPU 1: done.
[ 0.210775] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.210786] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.210794] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.210845] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.269957] Synchronize counters for CPU 2: done.
[ 0.300651] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.300661] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.300669] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.300725] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.355169] Synchronize counters for CPU 3: done.
[ 0.385057] smp: Brought up 1 node, 4 CPUs
[ 0.393189] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.403020] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.410029] pinctrl core: initialized pinctrl subsystem
[ 0.417862] NET: Registered protocol family 16
[ 0.423531] thermal_sys: Registered thermal governor 'step_wise'
[ 0.424483] cpuidle: using governor teo
[ 0.479319] clocksource: Switched to clocksource GIC
[ 0.486542] NET: Registered protocol family 2
[ 0.491420] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.500337] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.508649] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.516327] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.523463] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.529960] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.536420] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.543702] NET: Registered protocol family 1
[ 0.548000] PCI: CLS 0 bytes, default 32
[ 0.554487] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.564986] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.570829] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.581459] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.590812] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.596705] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.602577] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.608709] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.617571] printk: console [ttyS0] disabled
[ 0.621993] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.631065] printk: console [ttyS0] enabled
[ 0.631065] printk: console [ttyS0] enabled
[ 0.639483] printk: bootconsole [early0] disabled
[ 0.639483] printk: bootconsole [early0] disabled
[ 0.653293] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
[ 0.659719] nand: Winbond W29N01HV
[ 0.663110] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.670675] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 0.677271] 6 fixed-partitions partitions found on MTD device mt7621-nand
[ 0.684441] Creating 6 MTD partitions on "mt7621-nand":
[ 0.689705] 0x000000000000-0x000000080000 : "Boot"
[ 0.698245] 0x000000080000-0x000000100000 : "Config"
[ 0.706804] 0x000000100000-0x000000180000 : "Factory"
[ 0.715552] 0x000000180000-0x000003180000 : "firmware"
[ 0.963318] 2 fixed-partitions partitions found on MTD device firmware
[ 0.969945] Creating 2 MTD partitions on "firmware":
[ 0.974911] 0x000000000000-0x000000400000 : "kernel"
[ 1.001420] 0x000000400000-0x000003000000 : "ubi"
[ 1.229040] 0x000003180000-0x000006180000 : "alt_firmware"
[ 1.477197] 0x000006180000-0x000006200000 : "cbtinfo"
[ 1.530737] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.540800] mtk_soc_eth 1e100000.ethernet: generated random MAC address c6:c0:e4:d9:73:1c
[ 1.550030] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 1.558508] mtk_soc_eth 1e100000.ethernet: generated random MAC address 6e:ef:43:7c:d0:92
[ 1.567478] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21
[ 1.577280] i2c /dev entries driver
[ 1.583555] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 1.590334] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 1.599119] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 1.607317] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.615615] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 1.623455] NET: Registered protocol family 10
[ 1.630077] Segment Routing with IPv6
[ 1.633840] NET: Registered protocol family 17
[ 1.638345] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.651847] 8021q: 802.1Q VLAN Support v1.8
[ 1.659805] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.683624] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=26)
[ 1.695913] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=27)
[ 1.708289] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=28)
[ 1.720748] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=29)
[ 1.733330] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.743774] DSA: tree 0 setup
[ 1.747056] rt2880-pinmux pinctrl: pcie is already enabled
[ 1.752662] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 1.759381] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 1.768158] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 1.776328] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.784596] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 1.792373] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 1.800032] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 1.907421] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.913011] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 2.018723] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 2.025683] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 2.030556] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 2.035417] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 2.044890] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 2.051273] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 2.058125] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 2.065005] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.070501] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 2.080700] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 2.086698] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.092960] pci 0000:00:00.0: reg 0x14: [mem 0x60600000-0x6060ffff]
[ 2.099295] pci 0000:00:00.0: supports D1
[ 2.103290] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.109515] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 2.115541] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.121820] pci 0000:00:01.0: reg 0x14: [mem 0x60610000-0x6061ffff]
[ 2.128127] pci 0000:00:01.0: supports D1
[ 2.132137] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 2.139508] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 2.145550] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 2.152605] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 2.159311] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 2.166329] pci 0000:01:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 2.173055] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 2.180093] pci 0000:01:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 2.186891] pci 0000:01:00.0: supports D1 D2
[ 2.191159] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.197786] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 2.213857] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.219081] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 2.225177] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.231968] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 2.239166] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.246038] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 2.252092] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 2.259119] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 2.265825] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 2.272857] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 2.279569] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 2.286587] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 2.293407] pci 0000:02:00.0: supports D1 D2
[ 2.297662] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.304306] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 2.320476] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 2.325702] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 2.331797] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 2.338558] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 2.345767] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.352449] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.359038] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.365994] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.372596] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.379548] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.386308] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 2.393529] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 2.400313] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 2.407505] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 2.414295] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 2.421080] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 2.427841] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 2.434632] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 2.442379] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 2.450124] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 2.457845] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.462805] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 2.469590] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.476350] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 2.483569] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 2.491315] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 2.499037] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 2.506780] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.511743] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 2.518503] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 2.525273] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 2.535489] UBI: auto-attach mtd5
[ 2.538829] ubi0: attaching mtd5
[ 2.551524] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.216477] ubi0: scanning is finished
[ 3.236822] ubi0: attached mtd5 (name "ubi", size 44 MiB)
[ 3.242323] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.249175] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.255958] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.262914] ubi0: good PEBs: 352, bad PEBs: 0, corrupted PEBs: 0
[ 3.268893] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.276105] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1675633157
[ 3.285218] ubi0: available PEBs: 0, total reserved PEBs: 352, PEBs reserved for bad PEB handling: 20
[ 3.294461] ubi0: background thread "ubi_bgt0d" started, PID 455
[ 3.296861] block ubiblock0_0: created from ubi0:0(rootfs)
[ 3.306031] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.320393] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.331972] Freeing unused kernel memory: 1276K
[ 3.336506] This architecture does not have kernel memory protection.
[ 3.342987] Run /sbin/init as init process
[ 3.820109] init: Console is alive
[ 3.823954] init: - watchdog -
[ 3.894335] kmodloader: no module folders for kernel version 5.10.166 found
[ 3.919757] init: - preinit -
[ 4.645554] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.763170] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.351831] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.641720] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 5.650122] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 5.659044] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 5.666049] 8021q: adding VLAN 0 to HW filter on device lan1
[ 5.674337] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.868252] random: procd: uninitialized urandom read (4 bytes read)
[ 7.869384] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 7.880640] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 581
[ 8.082947] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 8.090799] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.100683] UBIFS (ubi0:1): FS size: 36569088 bytes (34 MiB, 288 LEBs), journal size 1777664 bytes (1 MiB, 14 LEBs)
[ 8.111085] UBIFS (ubi0:1): reserved for root: 1727248 bytes (1686 KiB)
[ 8.117674] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D29FC0E4-6E85-4239-B051-7578E62A59E4, small LPT model
[ 8.131530] mount_root: overlay filesystem has not been fully initialized yet
[ 8.140007] mount_root: switching to ubifs overlay
- config restore -
[ 8.445602] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.532634] procd: - early -
[ 8.535778] procd: - watchdog -
[ 9.149487] procd: - watchdog -
[ 9.153110] procd: - ubus -
[ 9.239476] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.247990] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.254994] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.268352] procd: - init -
Please press Enter to activate this console.
[ 9.841700] kmodloader: no module folders for kernel version 5.10.166 found
[ 10.041389] urngd: v1.0.2 started.
[ 10.219843] random: crng init done
[ 10.223265] random: 32 urandom warning(s) missed due to ratelimiting
[ 18.899891] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 18.915698] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 18.923937] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 18.933012] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 18.940113] 8021q: adding VLAN 0 to HW filter on device lan1
[ 18.948402] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.956104] br-lan: port 1(lan1) entered blocking state
[ 18.961833] br-lan: port 1(lan1) entered disabled state
[ 18.967936] device lan1 entered promiscuous mode
[ 18.972842] device eth0 entered promiscuous mode
[ 19.006329] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 19.013566] 8021q: adding VLAN 0 to HW filter on device lan2
[ 19.023647] br-lan: port 2(lan2) entered blocking state
[ 19.028945] br-lan: port 2(lan2) entered disabled state
[ 19.036826] device lan2 entered promiscuous mode
[ 19.053454] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 19.060670] 8021q: adding VLAN 0 to HW filter on device lan3
[ 19.069813] br-lan: port 3(lan3) entered blocking state
[ 19.075089] br-lan: port 3(lan3) entered disabled state
[ 19.081755] device lan3 entered promiscuous mode
[ 19.098356] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 19.105594] 8021q: adding VLAN 0 to HW filter on device lan4
[ 19.115178] br-lan: port 4(lan4) entered blocking state
[ 19.120707] br-lan: port 4(lan4) entered disabled state
[ 19.127519] device lan4 entered promiscuous mode
[ 19.148168] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [MediaTek MT7530 PHY] (irq=POLL)
[ 19.157762] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode
[ 22.794861] mt7530 mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control rx/tx
[ 22.802432] br-lan: port 4(lan4) entered blocking state
[ 22.807641] br-lan: port 4(lan4) entered forwarding state
[ 22.813960] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 33.203554] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 33.219507] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 33.227740] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 33.233763] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 33.243333] 8021q: adding VLAN 0 to HW filter on device lan1
[ 33.251811] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 33.259305] br-lan: port 1(lan1) entered blocking state
[ 33.264668] br-lan: port 1(lan1) entered disabled state
[ 33.271058] device lan1 entered promiscuous mode
[ 33.275730] device eth0 entered promiscuous mode
[ 33.311807] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 33.319076] 8021q: adding VLAN 0 to HW filter on device lan2
[ 33.328484] br-lan: port 2(lan2) entered blocking state
[ 33.334101] br-lan: port 2(lan2) entered disabled state
[ 33.341584] device lan2 entered promiscuous mode
[ 33.361234] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 33.368489] 8021q: adding VLAN 0 to HW filter on device lan3
[ 33.378151] br-lan: port 3(lan3) entered blocking state
[ 33.383827] br-lan: port 3(lan3) entered disabled state
[ 33.390773] device lan3 entered promiscuous mode
[ 33.408746] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 33.415916] 8021q: adding VLAN 0 to HW filter on device lan4
[ 33.425857] br-lan: port 4(lan4) entered blocking state
[ 33.431626] br-lan: port 4(lan4) entered disabled state
[ 33.438465] device lan4 entered promiscuous mode
[ 33.463902] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [MediaTek MT7530 PHY] (irq=POLL)
[ 33.473565] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode
[ 37.170947] mt7530 mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control rx/tx
[ 37.178472] br-lan: port 4(lan4) entered blocking state
[ 37.183727] br-lan: port 4(lan4) entered forwarding state
[ 37.191009] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.36.0 (2023-02-15 13:28:08 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r22071-3c66ac7e22
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
root@OpenWrt:/# ip a s
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1504 qdisc fq_codel state UP qlen 1000
link/ether ee:2a:e6:72:d6:10 brd ff:ff:ff:ff:ff:ff
inet6 fe80::ec2a:e6ff:fe72:d610/64 scope link
valid_lft forever preferred_lft forever
3: wan: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 82:24:9e:2f:82:55 brd ff:ff:ff:ff:ff:ff
4: lan4@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether ee:2a:e6:72:d6:10 brd ff:ff:ff:ff:ff:ff
5: lan3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether ee:2a:e6:72:d6:10 brd ff:ff:ff:ff:ff:ff
6: lan2@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether ee:2a:e6:72:d6:10 brd ff:ff:ff:ff:ff:ff
7: lan1@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noqueue state DOWN qlen 1000
link/ether ee:2a:e6:72:d6:10 brd ff:ff:ff:ff:ff:ff
8: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:0c:43:26:46:d8 brd ff:ff:ff:ff:ff:ff
9: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:0c:43:26:59:97 brd ff:ff:ff:ff:ff:ff
--------------------------------------------------
But in snapshot I never seem the wireless tab .
wlan0 and wlan1 are present
edit: run firstboot
Did anyone get this working without needing to hook up a serial cable and simply install from stock?
I flashed SNAPSHOT r22400-1558bbd116 to this device last night and it's working perfectly. The LED configuration needs work. I can only control the two amber LEDs and the blue power LED. The blue wifi activity led is constantly flashing and I wish I could disable this however this LED is not listed in /sys/class/leds
/sys/class/leds# ls
amber:wan amber:wps blue:power mt76-phy0 mt76-phy1
Need a new entry here for blue:wifi or blue:activity. The mt76-phy0 and mt76-phy1 are for the switch ports as far as I can tell.
can;t do it.
This used to be present but does not work properly with DSA.
Small improvement for E7350 and RT1800:
Open /etc/init.d/set-irq-affinity in your favourite editor and change
for irq in $(grep "mt76..e" /proc/interrupts | cut -d: -f1 | sed 's, *,,')
to
for irq in $(grep "mt7[69]..e" /proc/interrupts | cut -d: -f1 | sed 's, *,,')
and reboot.
You can check cat /proc/interrupts output before and after.
Made this change and rebooted. No difference in LED appearance or configuration that I can tell. What difference is supposed to be noticed?
I'll PR this.
This is for IRQ balancing, see https://openwrt.org/docs/guide-user/services/irqbalance
Posted here as this is probably the most active thread about these devices.
Since the initial problem seems to be solved and this discussion is drifting off-topic, I'm setting a timer for this topic to close.
Please open new topics for any other problems not related to this one.
Thanks!
This topic was automatically closed 24 hours after the last reply. New replies are no longer allowed.