i have a serial hookup for the router i think its the only way i can update the signed firmware to openwrt
what info would u guys need to get this router supported i can do a dump or whaterver if yiou guys tell me whgat commands to send it via putty i can get it done.
would the 2500 v4 firmware VIa this link work?
its basically the same hardware i think
Start by posting the complete boot sequence.
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Aug 27 2019 Time:14:25:14
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
mdio.w addr[0x00000007] value[0x00077070]
mdio.w addr[0x0000000D] value[0x0000001F]
mdio.w addr[0x0000000E] value[0x00000024]
mdio.w addr[0x0000000D] value[0x0000401F]
mdio.w addr[0x0000000E] value[0x00000000]
This verison of Uboot support Httpd Server 0.9
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 3
0
3: System Boot system code via Flash.
ethernet init
## Booting image at bc050000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 9090326 Bytes = 8.7 MB
Load Address: 80000000
Entry Point: 8000c150
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64
Starting kernel ...
怘€à˜†˜ø˜ffàfaø~ž~fž`žø†ø†ø†æ€˜€æ€˜€f30fæ˜`Ì
æ˜`Ìæ˜f†æ€f€˜€æ€˜€fÌϘ˜æ††f~Ø3ðLinux version 2.6.36+ (hhm@cybertan-team2) (gcc version 4.6.3
(Buildroot 2012.11.1) ) #4 Tue Aug 27 14:28:32 CST 2019
The CPU feqenuce set to 580 MHz
MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0006ab8d
Readback ErrCtl register=0006ab8d
Memory: 52628k/65536k available (3741k kernel code, 12844k reserved, 1031k data, 7284k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 54050404
RALINK_GPIOMODE = 54040404
***** Xtal 40MHz *****
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = fdbfffc0
*************** MT7628 PCIe RC mode *************
PCIE0 enabled
Port 0 N_FTS = 1b105000
init_rt2880pci done
bio: create slab <bio-0> at 0
SCSI subsystem initialized
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
fuse init (API version 7.15)
msgmni has been set to 102
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
flash manufacture id: ef, device id 40 18
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000ff0000 : "Kernel"
0x000000ff0000-0x000001000000 : "CBTinfo"
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000e89f
GMAC1_MAC_ADRL -- : 0x8006c3d4
Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000e89f
GMAC1_MAC_ADRL -- : 0x8006c3d4
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
=== pAd = c0105000, size = 1467448 ===
<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
RtmpChipOpsHook(492): Not support for HIF_MT yet!
mt7628_init()-->
mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
mt_bcn_buf_init(218): Not support for HIF_MT yet!
<--mt7628_init()
GACT probability NOT on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (822 buckets, 3288 max)
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_rtsp v0.6.21 loading
matchsize=264
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Warning: unable to open an initial console.
Freeing unused kernel memory: 7284k freed
Algorithmics/MIPS FPU Emulator v1.5
Password for 'root' changed
##### disable 1st wireless interface #####
##### disable 2nd wireless interface #####
##### disable 3rd wireless interface #####
rmmod: rlt_wifi: No such file or directory
rmmod: mt_wifi: No such file or directory
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
ipt_webstr: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
register rt2860
=== pAd = c0782000, size = 2114360 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=2
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd->flash_offset = 0x8000)
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
insmod: mt_wifi.ko: module not found
TX_BCN DESC a26b9000 size = 320
RX[0] DESC a26bc000 size = 1024
RX[1] DESC a26bd000 size = 1024
E2pAccessMode=2
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
[PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1
RTMPSetDefaultChannel() : default channel to 1
load fw image from fw_header_image
AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
FW Version:20151201
FW Build Date:20151201183641
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
NVM is FLASH mode
1. Phy Mode = 14
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 32
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(11): Not support for HIF_MT yet!
NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
MtAsicInitMac()-->
mt7628_init_mac_cr()-->
MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
<--mt_mac_init()
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
AntCfgInit(2940): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
CmdSlotTimeSet:(ret = 0)
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
[PMF]ap_pmf_init:: apidx=0, MFPC=1, MFPR=0, SHA256=0
[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=1, MFPR=0
[PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE
[PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet!
MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
reload DPD from flash , 0x9F = [c800] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 1, DoReload = 0
MtAsicSetTxPreamble(3026): Not support for HIF_MT yet!
MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
ap_ftkd> Initialize FT KDP Module...
Main bssid = e8:9f:80:06:c3:d6
<==== rt28xx_init, Status=0
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
WiFi Startup Cost (ra0): 5.484s
build time =
20141115060606a
rom patch for E3 IC
platform =
ALPS
hw/sw version =
ŠŠ
patch version =
FW Version:0.0.00 Build:1
Build Time:201507311614____
fw for E3 IC
RX[0] DESC a22bc000 size = 4096
RX[1] DESC a22bd000 size = 4096
E2pAccessMode=2
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
pAd->ed_chk = 1
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
[PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1
1. Phy Mode = 49
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0xffffff82, ALNAGain1=0x0, ALNAGain2=0x0
2. Phy Mode = 49
3. Phy Mode = 49
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
TX0 power compensation = 0x38
TX1 power compensation = 0x38
[PMF]APStartUp:: apidx=0, MFPC=1, MFPR=0, SHA256=0
[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=1, MFPR=0
[PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE
mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
mt76x2_calibration(channel = 42)
The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
Main bssid = e8:9f:80:06:c3:d7
mt76x2_reinit_agc_gain:original agc_vga0 = 0x58, agc_vga1 = 0x58
mt76x2_reinit_agc_gain:updated agc_vga0 = 0x58, agc_vga1 = 0x58
mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x29, hi_lna1 = 0x29
mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x29, hi_lna1 = 0x29
original vga value(chain0) = 58
original vga value(chain1) = 58
<==== rt28xx_init, Status=0
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
***iwpriv ra0 set IgmpSnEnable=1**
***iwpriv rai0 set IgmpSnEnable=1**
##### configVIF #####
FFFFFFE8:FFFFFF9F:FFFFFF80: 6:FFFFFFC3:FFFFFFD4
Raeth v3.1 (Tasklet)
phy_tx_ring = 0x01ef4000, tx_ring = 0xa1ef4000
phy_rx_ring0 = 0x01ef6000, rx_ring0 = 0xa1ef6000
GMAC1_MAC_ADRH -- : 0x0000e89f
GMAC1_MAC_ADRL -- : 0x8006c3d4
RT305x_ESW: Link Status Changed
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
rmmod: 8021q: No such file or directory
device eth2 entered promiscuous mode
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
done.
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
done.
device ra0 entered promiscuous mode
ifconfig: ioctl 0x8913 failed: No such device
device eth2.1 entered promiscuous mode
device rai0 entered promiscuous mode
brctl: bridge br0: Device or resource busy
##### enable 2nd wireless interface #####
Start WAN .....
wan stop ...
cmd=[killall radvd ]
killall: radvd: no process killed
stop_dhcp6c
cmd=[ip6tables -t filter -F ]
cmd=[ip6tables -t filter -Z ]
cmd=[ip6tables -t mangle -F ]
cmd=[ip6tables -t mangle -Z ]
Set 0 to /proc/sys/net/ipv6/conf/all/forwarding ...
delete tunnel 6rd failed: No such device
cmd=[killall -9 waninfo ]
killall: waninfo: no process killed
cmd=[killall dnsmasq ]
killall: dnsmasq: no process killed
cmd=[killall radvd ]
killall: radvd: no process killed
cmd=[killall dhcpd6 ]
killall: dhcpd6: no process killed
cmd=[ip6tables -F ]
/proc/sys/net/ctf/wan_mode: No such file or directory
cmd=[killall -9 nlinkd ]
killall: nlinkd: no process killed
cmd=[rmmod dnshook ]
rmmod: dnshook: No such file or directory
sh: cannot create /proc/unblock_proc: nonexistent directory
sh: cannot create /proc/hnd_proc: nonexistent directory
sh: cannot create /proc/hnd_proc: nonexistent directory
cmd=[killall -9 qos_bw_detect ]
killall: qos_bw_detect: no process killed
cmd=[killall igmprt ]
killall: igmprt: no process killed
cmd=[killall -9 igmprt ]
killall: igmprt: no process killed
cmd=[killall pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall ip-up ]
killall: ip-up: no process killed
cmd=[killall ip-down ]
killall: ip-down: no process killed
cmd=[killall -15 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -15 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 listen ]
killall: listen: no process killed
cmd=[killall -9 waninfo ]
killall: waninfo: no process killed
stop_dhcpc
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -9 ntpclient ]
killall: ntpclient: no process killed
cmd=[killall -9 ntp ]
killall: ntp: no process killed
cmd=[killall -9 redial ]
killall: redial: no process killed
cmd=[killall wan_auto_detect ]
killall: wan_auto_detect: no process killed
wan start boot ...
cmd=[touch /tmp/hosts ]
start_dhcpc:=====( wan_or_lan=wan )=====
dhclient -nw -cf /tmp/dhcpc-wan.conf -sf /bin/dhcpc -lf /tmp/dhcpc-wan.leases -pf /var/run/dhcpc-wan.pid eth2.2 &
cmd=[touch /tmp/hosts ]
br0: port 3(rai0) entering learning state
br0: port 3(rai0) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
lan stop ...
cmd=[killall -16 dhcpd ]
killall: dhcpd: no process killed
cmd=[killall -16 gn-dhcpd ]
killall: gn-dhcpd: no process killed
cmd=[killall gn-dhcpd ]
killall: gn-dhcpd: no process killed
Start dhcpd ...
lan start ...
br0 192.168.1.100
write_dhcpd_conf: file=/tmp/dhcpd-br0.conf, ifname=br0, lan_ip=lan_ipaddr lan_mask=lan_netmask
cmd=[dhcpd -cf /tmp/dhcpd-br0.conf -lf /tmp/dhcpd.leases -df /tmp/udhcpd.leases -pf /var/run/dhcpd.pid br0 ]
Internet Systems Consortium DHCP Server 4.1.1-P1
Copyright 2004-2010 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Wrote 0 leases to leases file.
Listening on Socket/br0/192.168.1.0/24
Sending on Socket/br0/192.168.1.0/24
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
br0: port 3(rai0) entering forwarding state
br0: port 2(eth2.1) entering forwarding state
br0: port 1(ra0) entering forwarding state
Set: phy[0].reg[0] = 3300
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[0] = 3300
Set: phy[3].reg[0] = 3300
Unknown option: -I
Unknown option: ra0
Jan 1 00:00:34 miniupnpd[2024]: WPS listening on port 7777
Unknown option: -I
Unknown option: rai0
Jan 1 00:00:34 miniupnpd[2027]: WPS listening on port 8888
iwpriv ra0 set IgmpSnEnable=1
iwpriv rai0 set IgmpSnEnable=1
killall: long_loop: no process killed
/sbin/internet.sh: line 816: nfchod: not found
wireless.c:restart_wps:3136:[restart_wps]wps_restart.wsc_enable=7
route: ioctl 0x890c failed: No such process
Unknown option: -I
Unknown option: ra0
Jan 1 00:00:35 miniupnpd[2688]: WPS listening on port 7777
Unknown option: -I
Unknown option: rai0
Jan 1 00:00:35 miniupnpd[2691]: WPS listening on port 8888
killall: rt2860apd: no process killed
wireless.c:restart_wps:3136:[restart_wps]wps_restart.wsc_enable=7
Unknown option: -I
Unknown option: ra0
Jan 1 00:00:35 miniupnpd[3231]: WPS listening on port 7777
Unknown option: -I
Unknown option: rai0
Jan 1 00:00:35 miniupnpd[3234]: WPS listening on port 8888
killall: rtinicapd: no process killed
Cannot find device "6rdtun"
0
webs: Listening for HTTP requests at address 192.168.1.1cmd=[cron ]
cron: can't open log file
/var/log/mess: No such file or directory
cron: can't write to log file
CRON (01/01-00:00:35-3252) STARTUP (fork ok)
[HTTPD Starting on /www]
cmd=[httpd ]
cmd=[route del -net 224.0.0.0 netmask 240.0.0.0 dev br0 ]
route: ioctl 0x890c failed: No such process
cmd=[route add -net 224.0.0.0 netmask 240.0.0.0 dev br0 ]
cmd=[cesmDNS -o /tmp/.mdns_host_info -d -h Linksys25823 -l 192.168.1.1 ]
cmd=[cesmDNS -o /tmp/.mdns_host_info -d -h myrouter -l 192.168.1.1 ]
cmd=[netbios /tmp/netbios.conf ]
cmd=[/bin/monitor_cable ]
init: can't log to /dev/tty5
starting pid 3302, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2019-08-26 09:48:24 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# cmd=[killall -1 nvram_daemon ]
start single service: unplug_wan_cable
stop_dhcp6c
cmd=[ip6tables -t filter -F ]
cmd=[ip6tables -t filter -Z ]
cmd=[ip6tables -t mangle -F ]
cmd=[ip6tables -t mangle -Z ]
Set 0 to /proc/sys/net/ipv6/conf/all/forwarding ...
cmd=[killall -9 waninfo ]
cmd=[killall -9 nlinkd ]
killall: nlinkd: no process killed
cmd=[rmmod dnshook ]
rmmod: dnshook: No such file or directory
cmd=[killall -9 qos_bw_detect ]
killall: qos_bw_detect: no process killed
cmd=[killall igmprt ]
killall: igmprt: no process killed
cmd=[killall -9 igmprt ]
killall: igmprt: no process killed
cmd=[killall pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall ip-up ]
killall: ip-up: no process killed
cmd=[killall ip-down ]
killall: ip-down: no process killed
cmd=[killall -15 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -15 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 listen ]
killall: listen: no process killed
cmd=[killall -9 waninfo ]
killall: waninfo: no process killed
stop_dhcpc
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -9 ntpclient ]
killall: ntpclient: no process killed
cmd=[killall -9 ntp ]
killall: ntp: no process killed
cmd=[killall -9 redial ]
killall: redial: no process killed
cmd=[killall wan_auto_detect ]
killall: wan_auto_detect: no process killed
unplug_wan_cable:dhclient -r -6 -N -P -d -q -nw -cf /tmp/dhcp6c-wan.conf -sf /bin/client6 -lf /tmp/dhcp6c-wan.leases -pf /var/run/dhcp6c-w
an.pid eth2.2
ist that what u needed? and its a e5400 btw.
It's a start.
Are you able to get console access too?
sorry for delayed response but i installed the file in the thread from the e2500 and its working but i cant instlall the new linksys update because its not listed : (
can i still get he info you need with open wrt aready installed?