Lanner NCA-1010 HW discovery

[frollic]

Really love this device, fanless, with tiny foot print - 12x12x1,5 cm

stock photos, mine didn't come with any radio/antenna.

Model 1010A is single core Atom E3815, 1010B is dual core E3825 CPU.

Device page: https://www.lannerinc.com/products/network-appliances/x86-desktop-network-appliances/nca-1010
User manual: https://www.lannerinc.com/support/download-center/category/16-network-appliances?download=118:nca-1010-user-manual&start=20

My unit came with an Atom 3825 CPU, 32GB mSATA drive, and 4GB of RAM.
RAM is upgradeable to 8GB, slot located on the back side of the PCB.
It got 3x intel i211 NICs, RJ45 serial console, a HDMI port, and USB3 + USB2 ports (one of each).

There's room for an additional mPCI card.

It's rated for 12V 3A, 5,5 x 2,5mm (2,1mm seem to work too) barrel.

Serial console for AMI BIOS access is running at 115200, 8n1.

Boot priority can be set in BIOS, it'd be easy to run openwrt off an USB drive.

Default (on my unit) was boot USB 1st, I only needed to insert the prepped openwrt flash drive, and boot.

Routing at 1gbit, using iperf3, requires roughly 50% of the available CPU power.

22.03.4 boot

[    0.000000] Linux version 5.10.176 (builder@buildhost) (x86_64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20123-38ccc47687) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sun Apr 9 12:27:46 2023
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz root=PARTUUID=93ffdd41-3e4a-2ac5-91b9-53e979fb5902 rootwait console=tty0 console=ttyS0,115200n8 noinitrd
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009ffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000b97abfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000b97ac000-0x00000000b97dbfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000b97dc000-0x00000000b97ebfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000b97ec000-0x00000000b9949fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000b994a000-0x00000000b9bd0fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000b9bd1000-0x00000000b9c1cfff] type 20
[    0.000000] BIOS-e820: [mem 0x00000000b9c1d000-0x00000000b9c1dfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000b9c1e000-0x00000000b9c5ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000b9c60000-0x00000000b9dcefff] usable
[    0.000000] BIOS-e820: [mem 0x00000000b9dcf000-0x00000000b9ff9fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000b9ffa000-0x00000000b9ffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed03000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed0c000-0x00000000fed0ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fef00000-0x00000000feffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.31 by American Megatrends
[    0.000000] efi: ACPI=0xb97e0000 ACPI 2.0=0xb97e0000 ESRT=0xb9bcd218 SMBIOS=0xf04d0
[    0.000000] SMBIOS 2.8 present.
[    0.000000] DMI: Lanner NCA-1010B-ST1/Aptio CRB, BIOS 5.6.5 05/17/2017
[    0.000000] tsc: Detected 1333.333 MHz processor
[    0.001973] last_pfn = 0x140000 max_arch_pfn = 0x400000000
[    0.002198] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT
[    0.002487] last_pfn = 0xba000 max_arch_pfn = 0x400000000
[    0.010799] found SMP MP-table at [mem 0x000fd6d0-0x000fd6df]
[    0.010831] esrt: Reserving ESRT space from 0x00000000b9bcd218 to 0x00000000b9bcd250.
[    0.013341] Secure boot disabled
[    0.013352] ACPI: Early table checksum verification disabled
[    0.013363] ACPI: RSDP 0x00000000B97E0000 000024 (v02 ALASKA)
[    0.013379] ACPI: XSDT 0x00000000B97E0078 000074 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.013398] ACPI: FACP 0x00000000B97EA730 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
[    0.013417] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20200925/tbfadt-564)
[    0.013433] ACPI: DSDT 0x00000000B97E0180 00A5AB (v02 ALASKA A M I    01072009 INTL 20120913)
[    0.013449] ACPI: FACS 0x00000000B9949F80 000040
[    0.013462] ACPI: APIC 0x00000000B97EA840 000068 (v03 ALASKA A M I    01072009 AMI  00010013)
[    0.013478] ACPI: FPDT 0x00000000B97EA8A8 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.013493] ACPI: LPIT 0x00000000B97EA8F0 000104 (v01 ALASKA A M I    00000003 VLV2 0100000D)
[    0.013508] ACPI: MCFG 0x00000000B97EA9F8 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
[    0.013523] ACPI: HPET 0x00000000B97EAA38 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
[    0.013538] ACPI: SSDT 0x00000000B97EAA70 000763 (v01 PmRef  CpuPm    00003000 INTL 20061109)
[    0.013553] ACPI: SSDT 0x00000000B97EB1D8 000290 (v01 PmRef  Cpu0Tst  00003000 INTL 20061109)
[    0.013568] ACPI: SSDT 0x00000000B97EB468 00017A (v01 PmRef  ApTst    00003000 INTL 20061109)
[    0.013583] ACPI: UEFI 0x00000000B97EB5E8 000042 (v01 ALASKA A M I    00000000      00000000)
[    0.013599] ACPI: Reserving FACP table memory at [mem 0xb97ea730-0xb97ea83b]
[    0.013606] ACPI: Reserving DSDT table memory at [mem 0xb97e0180-0xb97ea72a]
[    0.013611] ACPI: Reserving FACS table memory at [mem 0xb9949f80-0xb9949fbf]
[    0.013617] ACPI: Reserving APIC table memory at [mem 0xb97ea840-0xb97ea8a7]
[    0.013623] ACPI: Reserving FPDT table memory at [mem 0xb97ea8a8-0xb97ea8eb]
[    0.013629] ACPI: Reserving LPIT table memory at [mem 0xb97ea8f0-0xb97ea9f3]
[    0.013635] ACPI: Reserving MCFG table memory at [mem 0xb97ea9f8-0xb97eaa33]
[    0.013641] ACPI: Reserving HPET table memory at [mem 0xb97eaa38-0xb97eaa6f]
[    0.013647] ACPI: Reserving SSDT table memory at [mem 0xb97eaa70-0xb97eb1d2]
[    0.013653] ACPI: Reserving SSDT table memory at [mem 0xb97eb1d8-0xb97eb467]
[    0.013659] ACPI: Reserving SSDT table memory at [mem 0xb97eb468-0xb97eb5e1]
[    0.013665] ACPI: Reserving UEFI table memory at [mem 0xb97eb5e8-0xb97eb629]
[    0.013726] Zone ranges:
[    0.013732]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.013741]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.013748]   Normal   [mem 0x0000000100000000-0x000000013fffffff]
[    0.013755] Movable zone start for each node
[    0.013759] Early memory node ranges
[    0.013765]   node   0: [mem 0x0000000000001000-0x000000000008efff]
[    0.013770]   node   0: [mem 0x0000000000090000-0x000000000009ffff]
[    0.013775]   node   0: [mem 0x0000000000100000-0x00000000b97abfff]
[    0.013780]   node   0: [mem 0x00000000b9c1d000-0x00000000b9c1dfff]
[    0.013785]   node   0: [mem 0x00000000b9c60000-0x00000000b9dcefff]
[    0.013790]   node   0: [mem 0x00000000b9ffa000-0x00000000b9ffffff]
[    0.013796]   node   0: [mem 0x0000000100000000-0x000000013fffffff]
[    0.013802] Initmem setup node 0 [mem 0x0000000000001000-0x000000013fffffff]
[    0.013844] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.013848] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.013955] On node 0, zone DMA: 96 pages in unavailable ranges
[    0.034121] On node 0, zone DMA32: 1137 pages in unavailable ranges
[    0.034142] On node 0, zone DMA32: 66 pages in unavailable ranges
[    0.034172] On node 0, zone DMA32: 555 pages in unavailable ranges
[    0.042266] On node 0, zone Normal: 24576 pages in unavailable ranges
[    0.042275] x86/hpet: Will disable the HPET for this platform because it's not reliable
[    0.042291] Reserving Intel graphics memory at [mem 0xbb000000-0xbeffffff]
[    0.042524] ACPI: PM-Timer IO Port: 0x408
[    0.042552] ACPI: LAPIC_NMI (acpi_id[0x01] res edge lint[0x1d])
[    0.042557] ACPI: NMI not connected to LINT 1!
[    0.042563] ACPI: LAPIC_NMI (acpi_id[0x02] dfl res lint[0xc7])
[    0.042567] ACPI: NMI not connected to LINT 1!
[    0.042587] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-86
[    0.042595] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.042603] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.042620] Using ACPI (MADT) for SMP configuration information
[    0.042627] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.042640] TSC deadline timer available
[    0.042646] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.042726] [mem 0xbf000000-0xdfffffff] available for PCI devices
[    0.042734] Booting paravirtualized kernel on bare hardware
[    0.042743] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.042764] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[    0.043688] percpu: Embedded 48 pages/cpu s157016 r8192 d31400 u1048576
[    0.043793] Built 1 zonelists, mobility grouping on.  Total pages: 1006127
[    0.043802] Kernel command line: BOOT_IMAGE=/boot/vmlinuz root=PARTUUID=93ffdd41-3e4a-2ac5-91b9-53e979fb5902 rootwait console=tty0 console=ttyS0,115200n8 noinitrd
[    0.045410] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.046145] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.046216] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.107099] Memory: 3687076K/4088576K available (14338K kernel code, 1127K rwdata, 2084K rodata, 1472K init, 1384K bss, 401244K reserved, 0K cma-reserved)
[    0.107246] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.107266] Kernel/User page tables isolation: enabled
[    0.107423] rcu: Hierarchical RCU implementation.
[    0.107433] rcu:     RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[    0.107438]  Tracing variant of Tasks RCU enabled.
[    0.107444] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.107449] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.107473] NR_IRQS: 33024, nr_irqs: 512, preallocated irqs: 16
[    0.107988] Console: colour dummy device 80x25
[    0.108732] printk: console [tty0] enabled
[    1.050206] printk: console [ttyS0] enabled
[    1.054896] ACPI: Core revision 20200925
[    1.059459] APIC: Switch to symmetric I/O mode setup
[    1.065632] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x13381e82524, max_idle_ns: 440795248224 ns
[    1.077407] Calibrating delay loop (skipped), value calculated using timer frequency.. 2666.66 BogoMIPS (lpj=13333330)
[    1.087404] pid_max: default: 32768 minimum: 301
[    1.087404] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.087404] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.087404] mce: CPU0: Thermal monitoring enabled (TM1)
[    1.087404] process: using mwait in idle threads
[    1.087404] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[    1.087404] Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
[    1.087404] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    1.087404] Spectre V2 : Mitigation: Retpolines
[    1.087404] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    1.087404] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT
[    1.087404] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[    1.087404] MMIO Stale Data: Unknown: No mitigations
[    1.087404] Freeing SMP alternatives memory: 40K
[    1.087404] smpboot: CPU0: Intel(R) Atom(TM) CPU  E3825  @ 1.33GHz (family: 0x6, model: 0x37, stepping: 0x9)
[    1.087920] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, 8-deep LBR, full-width counters, Intel PMU driver.
[    1.097414] ... version:                3
[    1.101894] ... bit width:              40
[    1.106469] ... generic registers:      2
[    1.107411] ... value mask:             000000ffffffffff
[    1.113348] ... max period:             0000007fffffffff
[    1.117410] ... fixed-purpose events:   3
[    1.121889] ... event mask:             0000000700000003
[    1.127758] rcu: Hierarchical SRCU implementation.
[    1.133269] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    1.137557] smp: Bringing up secondary CPUs ...
[    1.142999] x86: Booting SMP configuration:
[    1.147418] .... node  #0, CPUs:      #1
[    1.147683] smp: Brought up 1 node, 2 CPUs
[    1.156649] smpboot: Max logical packages: 1
[    1.157419] smpboot: Total of 2 processors activated (5333.33 BogoMIPS)
[    1.166242] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    1.167428] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    1.175088] pinctrl core: initialized pinctrl subsystem
[    1.178546] NET: Registered protocol family 16
[    1.184141] thermal_sys: Registered thermal governor 'step_wise'
[    1.184145] thermal_sys: Registered thermal governor 'user_space'
[    1.187634] cpuidle: using governor ladder
[    1.197586] ACPI: bus type PCI registered
[    1.202069] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    1.207583] PCI: Using configuration type 1 for base access
[    1.214125] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    1.244896] cryptd: max_cpu_qlen set to 1000
[    1.248893] ACPI: Added _OSI(Module Device)
[    1.253577] ACPI: Added _OSI(Processor Device)
[    1.257433] ACPI: Added _OSI(3.0 _SCP Extensions)
[    1.262691] ACPI: Added _OSI(Processor Aggregator Device)
[    1.267414] ACPI: Added _OSI(Linux-Dell-Video)
[    1.272381] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    1.277413] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    1.300606] ACPI: 4 ACPI AML tables successfully acquired and loaded
[    1.312540] ACPI: Dynamic OEM Table Load:
[    1.317050] ACPI: SSDT 0xFFFF88810037B000 000311 (v01 PmRef  Cpu0Ist  00003000 INTL 20061109)
[    1.319380] ACPI: Dynamic OEM Table Load:
[    1.323880] ACPI: SSDT 0xFFFF888100B61800 000433 (v01 PmRef  Cpu0Cst  00003001 INTL 20061109)
[    1.329860] ACPI: Dynamic OEM Table Load:
[    1.334359] ACPI: SSDT 0xFFFF888100A32800 00015F (v01 PmRef  ApIst    00003000 INTL 20061109)
[    1.339120] ACPI: Dynamic OEM Table Load:
[    1.343617] ACPI: SSDT 0xFFFF888100922000 00008D (v01 PmRef  ApCst    00003000 INTL 20061109)
[    1.350715] ACPI: Interpreter enabled
[    1.354832] ACPI: (supports S0 S5)
[    1.357415] ACPI: Using IOAPIC for interrupt routing
[    1.363068] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    1.368446] ACPI: Enabled 9 GPEs in block 00 to 3F
[    1.386625] ACPI: Power Resource [USBC] (on)
[    1.392818] ACPI: Power Resource [PLPE] (on)
[    1.398080] ACPI: Power Resource [PLPE] (on)
[    1.411208] ACPI: Power Resource [CLK0] (on)
[    1.416111] ACPI: Power Resource [CLK1] (on)
[    1.541667] ACPI: Power Resource [FN00] (off)
[    1.548150] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    1.555077] acpi PNP0A08:00: _OSC: OS supports [Segments MSI HPX-Type3]
[    1.557864] acpi PNP0A08:00: _OSC failed (AE_ERROR)
[    1.564254] PCI host bridge to bus 0000:00
[    1.567418] pci_bus 0000:00: root bus resource [io  0x0070-0x0077]
[    1.574330] pci_bus 0000:00: root bus resource [io  0x0000-0x006f window]
[    1.577414] pci_bus 0000:00: root bus resource [io  0x0078-0x0cf7 window]
[    1.585004] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    1.587413] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    1.595783] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    1.597423] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[    1.605793] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[    1.607414] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.613573] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
[    1.619267] pci 0000:00:02.0: [8086:0f31] type 00 class 0x030000
[    1.626002] pci 0000:00:02.0: reg 0x10: [mem 0xd0000000-0xd03fffff]
[    1.627427] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff pref]
[    1.634932] pci 0000:00:02.0: reg 0x20: [io  0xe080-0xe087]
[    1.637441] pci 0000:00:02.0: BAR 2: assigned to efifb
[    1.643582] pci 0000:00:13.0: [8086:0f23] type 00 class 0x010601
[    1.647431] pci 0000:00:13.0: reg 0x10: [io  0xe070-0xe077]
[    1.653672] pci 0000:00:13.0: reg 0x14: [io  0xe060-0xe063]
[    1.657430] pci 0000:00:13.0: reg 0x18: [io  0xe050-0xe057]
[    1.663670] pci 0000:00:13.0: reg 0x1c: [io  0xe040-0xe043]
[    1.667422] pci 0000:00:13.0: reg 0x20: [io  0xe020-0xe03f]
[    1.673654] pci 0000:00:13.0: reg 0x24: [mem 0xd0916000-0xd09167ff]
[    1.677472] pci 0000:00:13.0: PME# supported from D3hot
[    1.683670] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
[    1.687434] pci 0000:00:14.0: reg 0x10: [mem 0xd0900000-0xd090ffff 64bit]
[    1.695102] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    1.697773] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
[    1.704515] pci 0000:00:1a.0: reg 0x10: [mem 0xd0500000-0xd05fffff]
[    1.707427] pci 0000:00:1a.0: reg 0x14: [mem 0xd0400000-0xd04fffff]
[    1.714555] pci 0000:00:1a.0: PME# supported from D0 D3hot
[    1.717835] pci 0000:00:1b.0: [8086:0f04] type 00 class 0x040300
[    1.724584] pci 0000:00:1b.0: reg 0x10: [mem 0xd0910000-0xd0913fff 64bit]
[    1.727506] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    1.734673] pci 0000:00:1c.0: [8086:0f48] type 01 class 0x060400
[    1.737503] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.744673] pci 0000:00:1c.1: [8086:0f4a] type 01 class 0x060400
[    1.747502] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    1.754670] pci 0000:00:1c.2: [8086:0f4c] type 01 class 0x060400
[    1.757502] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    1.764669] pci 0000:00:1c.3: [8086:0f4e] type 01 class 0x060400
[    1.767501] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    1.774678] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
[    1.777859] pci 0000:00:1f.3: [8086:0f12] type 00 class 0x0c0500
[    1.784619] pci 0000:00:1f.3: reg 0x10: [mem 0xd0914000-0xd091401f]
[    1.787489] pci 0000:00:1f.3: reg 0x20: [io  0xe000-0xe01f]
[    1.794260] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    1.797574] pci 0000:02:00.0: [8086:1539] type 00 class 0x020000
[    1.804330] pci 0000:02:00.0: reg 0x10: [mem 0xd0800000-0xd081ffff]
[    1.807451] pci 0000:02:00.0: reg 0x18: [io  0xd000-0xd01f]
[    1.813707] pci 0000:02:00.0: reg 0x1c: [mem 0xd0820000-0xd0823fff]
[    1.817570] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    1.824579] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    1.827417] pci 0000:00:1c.1:   bridge window [io  0xd000-0xdfff]
[    1.834233] pci 0000:00:1c.1:   bridge window [mem 0xd0800000-0xd08fffff]
[    1.837578] pci 0000:03:00.0: [8086:1539] type 00 class 0x020000
[    1.844334] pci 0000:03:00.0: reg 0x10: [mem 0xd0700000-0xd071ffff]
[    1.847451] pci 0000:03:00.0: reg 0x18: [io  0xc000-0xc01f]
[    1.853706] pci 0000:03:00.0: reg 0x1c: [mem 0xd0720000-0xd0723fff]
[    1.857569] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    1.864575] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    1.867417] pci 0000:00:1c.2:   bridge window [io  0xc000-0xcfff]
[    1.874234] pci 0000:00:1c.2:   bridge window [mem 0xd0700000-0xd07fffff]
[    1.877572] pci 0000:04:00.0: [8086:1539] type 00 class 0x020000
[    1.884327] pci 0000:04:00.0: reg 0x10: [mem 0xd0600000-0xd061ffff]
[    1.887451] pci 0000:04:00.0: reg 0x18: [io  0xb000-0xb01f]
[    1.893707] pci 0000:04:00.0: reg 0x1c: [mem 0xd0620000-0xd0623fff]
[    1.897577] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[    1.904579] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    1.907417] pci 0000:00:1c.3:   bridge window [io  0xb000-0xbfff]
[    1.914233] pci 0000:00:1c.3:   bridge window [mem 0xd0600000-0xd06fffff]
[    1.920179] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    1.927602] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    1.935488] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 11 12 14 15)
[    1.937596] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[    1.945484] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15)
[    1.947594] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 10 11 12 14 15)
[    1.955483] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[    1.957605] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 10 11 12 14 15)
[    1.968281] SCSI subsystem initialized
[    1.972752] ACPI: bus type USB registered
[    1.977296] usbcore: registered new interface driver usbfs
[    1.977459] usbcore: registered new interface driver hub
[    1.983425] usbcore: registered new device driver usb
[    1.987677] Registered efivars operations
[    1.992782] PCI: Using ACPI for IRQ routing
[    1.998033] clocksource: Switched to clocksource tsc-early
[    2.004426] pnp: PnP ACPI init
[    2.007786] system 00:01: [io  0x0680-0x069f] has been reserved
[    2.014414] system 00:01: [io  0x0400-0x047f] has been reserved
[    2.021054] system 00:01: [io  0x0500-0x05fe] has been reserved
[    2.027684] system 00:01: [io  0x0600-0x061f] has been reserved
[    2.034306] system 00:01: [io  0x164e-0x164f] has been reserved
[    2.043149] system 00:02: [mem 0xe0000000-0xefffffff] has been reserved
[    2.050572] system 00:02: [mem 0xfed01000-0xfed01fff] has been reserved
[    2.057979] system 00:02: [mem 0xfed03000-0xfed03fff] has been reserved
[    2.065377] system 00:02: [mem 0xfed04000-0xfed04fff] has been reserved
[    2.072783] system 00:02: [mem 0xfed08000-0xfed08fff] has been reserved
[    2.080191] system 00:02: [mem 0xfed1c000-0xfed1cfff] has been reserved
[    2.087604] system 00:02: [mem 0xfee00000-0xfeefffff] could not be reserved
[    2.095390] system 00:02: [mem 0xfef00000-0xfeffffff] has been reserved
[    2.104929] pnp: PnP ACPI: found 4 devices

EDIT: Added photo of the back of the PCB, since I opened it to up, to upgrade the RAM to 8GB.
and a review https://techblog.paalijarvi.fi/2016/01/24/reviewing-lanner-nca-1010b-fanless-gateway-box-with-intel-nics/

[frollic]

boot con'd.

[    2.116693] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    2.126733] NET: Registered protocol family 2
[    2.131876] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    2.142105] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    2.151703] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    2.160713] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[    2.169138] TCP: Hash tables configured (established 32768 bind 32768)
[    2.176561] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    2.184135] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    2.192310] NET: Registered protocol family 1
[    2.197213] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000
[    2.206390] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[    2.219241] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000 add_align 100000
[    2.231023] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[    2.243874] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[    2.256730] pci 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000
[    2.269605] pci 0000:00:1c.0: BAR 14: assigned [mem 0xd0a00000-0xd0bfffff]
[    2.277307] pci 0000:00:1c.0: BAR 15: assigned [mem 0xd0c00000-0xd0dfffff 64bit pref]
[    2.286087] pci 0000:00:1c.1: BAR 15: assigned [mem 0xd0e00000-0xd0ffffff 64bit pref]
[    2.294867] pci 0000:00:1c.2: BAR 15: assigned [mem 0xd1000000-0xd11fffff 64bit pref]
[    2.303648] pci 0000:00:1c.3: BAR 15: assigned [mem 0xd1200000-0xd13fffff 64bit pref]
[    2.312420] pci 0000:00:1c.0: BAR 13: assigned [io  0x2000-0x2fff]
[    2.319346] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    2.324899] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    2.331730] pci 0000:00:1c.0:   bridge window [mem 0xd0a00000-0xd0bfffff]
[    2.339333] pci 0000:00:1c.0:   bridge window [mem 0xd0c00000-0xd0dfffff 64bit pref]
[    2.348008] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    2.353559] pci 0000:00:1c.1:   bridge window [io  0xd000-0xdfff]
[    2.360388] pci 0000:00:1c.1:   bridge window [mem 0xd0800000-0xd08fffff]
[    2.367991] pci 0000:00:1c.1:   bridge window [mem 0xd0e00000-0xd0ffffff 64bit pref]
[    2.376656] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    2.382216] pci 0000:00:1c.2:   bridge window [io  0xc000-0xcfff]
[    2.389047] pci 0000:00:1c.2:   bridge window [mem 0xd0700000-0xd07fffff]
[    2.396640] pci 0000:00:1c.2:   bridge window [mem 0xd1000000-0xd11fffff 64bit pref]
[    2.405314] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    2.410875] pci 0000:00:1c.3:   bridge window [io  0xb000-0xbfff]
[    2.417701] pci 0000:00:1c.3:   bridge window [mem 0xd0600000-0xd06fffff]
[    2.425293] pci 0000:00:1c.3:   bridge window [mem 0xd1200000-0xd13fffff 64bit pref]
[    2.433967] pci_bus 0000:00: resource 4 [io  0x0070-0x0077]
[    2.440209] pci_bus 0000:00: resource 5 [io  0x0000-0x006f window]
[    2.447119] pci_bus 0000:00: resource 6 [io  0x0078-0x0cf7 window]
[    2.454044] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    2.460966] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[    2.468665] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[    2.476353] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[    2.484147] pci_bus 0000:00: resource 11 [mem 0xc0000000-0xffffffff window]
[    2.491942] pci_bus 0000:01: resource 0 [io  0x2000-0x2fff]
[    2.498183] pci_bus 0000:01: resource 1 [mem 0xd0a00000-0xd0bfffff]
[    2.505191] pci_bus 0000:01: resource 2 [mem 0xd0c00000-0xd0dfffff 64bit pref]
[    2.513283] pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
[    2.519524] pci_bus 0000:02: resource 1 [mem 0xd0800000-0xd08fffff]
[    2.526532] pci_bus 0000:02: resource 2 [mem 0xd0e00000-0xd0ffffff 64bit pref]
[    2.534609] pci_bus 0000:03: resource 0 [io  0xc000-0xcfff]
[    2.540850] pci_bus 0000:03: resource 1 [mem 0xd0700000-0xd07fffff]
[    2.547867] pci_bus 0000:03: resource 2 [mem 0xd1000000-0xd11fffff 64bit pref]
[    2.555943] pci_bus 0000:04: resource 0 [io  0xb000-0xbfff]
[    2.562182] pci_bus 0000:04: resource 1 [mem 0xd0600000-0xd06fffff]
[    2.569204] pci_bus 0000:04: resource 2 [mem 0xd1200000-0xd13fffff 64bit pref]
[    2.577480] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    2.587600] PCI: CLS 64 bytes, default 64
[    2.592233] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    2.599519] software IO TLB: mapped [mem 0x00000000a6c58000-0x00000000aac58000] (64MB)
[    2.608928] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x13381e82524, max_idle_ns: 440795248224 ns
[    2.620186] clocksource: Switched to clocksource tsc
[    2.626621] simple-framebuffer simple-framebuffer.0: framebuffer at 0xc0000000, 0x1d5000 bytes, mapped to 0x0000000083536d23
[    2.639208] simple-framebuffer simple-framebuffer.0: format=a8r8g8b8, mode=800x600x32, linelength=3200
[    2.654374] Console: switching to colour frame buffer device 100x37
[    2.666087] simple-framebuffer simple-framebuffer.0: fb0: simplefb registered!
[    2.676050] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    2.686018] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.693121] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    2.703601] hv_vmbus: registering driver hyperv_fb
[    2.710751] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    2.720373] ACPI: Power Button [PWRB]
[    2.724637] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    2.734174] ACPI: Sleep Button [SLPB]
[    2.738460] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    2.746942] ACPI: Power Button [PWRF]
[    2.755659] thermal LNXTHERM:00: registered as thermal_zone0
[    2.764932] ACPI: Thermal Zone [TZ01] (27 C)
[    2.772909] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.803257] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    2.815967] hpet: number irqs doesn't agree with number of timers
[    2.825954] Non-volatile memory driver v1.3
[    2.833804] Linux agpgart interface v0.103
[    2.842367] fb0: switching to inteldrmfb from simple
[    2.851027] Console: switching to colour dummy device 80x25
[    2.883641] [drm] Initialized i915 1.6.0 20200917 for 0000:00:02.0 on minor 0
[    2.893980] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    2.902381] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
[    2.916562] loop: module loaded
[    2.920196] Guest personality initialized and is inactive
[    2.926275] VMCI host device registered (name=vmci, major=10, minor=63)
[    2.933686] Initialized host personality
[    2.938384] Loading iSCSI transport class v2.0-870.
[    2.944841] VMware PVSCSI driver - version 1.0.7.0-k
[    2.950477] hv_vmbus: registering driver hv_storvsc
[    2.956969] ahci 0000:00:13.0: controller can't do DEVSLP, turning off
[    2.964441] ahci 0000:00:13.0: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x1 impl SATA mode
[    2.973513] ahci 0000:00:13.0: flags: 64bit ncq pm led clo pio slum part deso
[    2.983135] scsi host0: ahci
[    2.987208] scsi host1: ahci
[    2.990604] ata1: SATA max UDMA/133 abar m2048@0xd0916000 port 0xd0916100 irq 92
[    2.998903] ata2: DUMMY
[    3.001986] VMware vmxnet3 virtual NIC driver - version 1.5.0.0-k-NAPI
[    3.009366] hv_vmbus: registering driver hv_netvsc
[    3.014723] Fusion MPT base driver 3.04.20
[    3.019310] Copyright (c) 1999-2008 LSI Corporation
[    3.024775] Fusion MPT SPI Host driver 3.04.20
[    3.029781] Fusion MPT SAS Host driver 3.04.20
[    3.034790] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.042100] ehci-pci: EHCI PCI platform driver
[    3.047098] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.054030] ohci-pci: OHCI PCI platform driver
[    3.059032] ohci-platform: OHCI generic platform driver
[    3.064900] uhci_hcd: USB Universal Host Controller Interface driver
[    3.072399] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    3.078278] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    3.087653] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[    3.097885] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    3.105776] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    3.111646] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    3.119924] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    3.129184] hub 1-0:1.0: USB hub found
[    3.133434] hub 1-0:1.0: 6 ports detected
[    3.139447] hub 2-0:1.0: USB hub found
[    3.143679] hub 2-0:1.0: 1 port detected
[    3.148548] usbcore: registered new interface driver usb-storage
[    3.155372] i8042: PNP: No PS/2 controller found.
[    3.160676] hv_vmbus: registering driver hyperv_keyboard
[    3.166679] rtc_cmos 00:00: RTC can wake from S4
[    3.172269] rtc_cmos 00:00: registered as rtc0
[    3.177293] rtc_cmos 00:00: setting system clock to 2023-04-24T06:21:31 UTC (1682317291)
[    3.186401] rtc_cmos 00:00: alarms up to one month, y3k, 242 bytes nvram
[    3.195343] intel_pstate: Intel P-state driver initializing
[    3.201897] sdhci: Secure Digital Host Controller Interface driver
[    3.208909] sdhci: Copyright(c) Pierre Ossman
[    3.214509] hid: raw HID events driver (C) Jiri Kosina
[    3.220366] hv_vmbus: registering driver hid_hyperv
[    3.225871] usbcore: registered new interface driver usbhid
[    3.232121] usbhid: USB HID core driver
[    3.236621] hv_utils: Registering HyperV Utility Driver
[    3.242488] hv_vmbus: registering driver hv_utils
[    3.247765] hv_vmbus: registering driver hv_balloon
[    3.253609] NET: Registered protocol family 10
[    3.259243] Segment Routing with IPv6
[    3.263393] NET: Registered protocol family 17
[    3.268453] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    3.282988] 8021q: 802.1Q VLAN Support v1.8
[    3.287767] NET: Registered protocol family 40
[    3.293403] microcode: sig=0x30679, pf=0x1, revision=0x901
[    3.299562] microcode: Microcode Update Driver: v2.2.
[    3.299577] IPI shorthand broadcast: enabled
[    3.310087] SSE version of gcm_enc/dec engaged.
[    3.316712] sched_clock: Marking stable (2347101480, 969515080)->(3745963273, -429346713)
[    3.326013] registered taskstats version 1
[    3.447882] usb 1-3: new high-speed USB device number 2 using xhci_hcd
[    3.471662] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    3.478876] ata1.00: ATA-11: SATA SSD, SBFM01.2, max UDMA/133
[    3.485324] ata1.00: 62533296 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    3.493253] ata1.00: configured for UDMA/133
[    3.633865] usb-storage 1-3:1.0: USB Mass Storage device detected
[    3.641978] scsi host2: usb-storage 1-3:1.0
[    3.727838] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[    3.765726] scsi 0:0:0:0: Direct-Access     ATA      SATA SSD         01.2 PQ: 0 ANSI: 5
[    3.776026] sd 0:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB)
[    3.784563] sd 0:0:0:0: [sda] Write Protect is off
[    3.790039] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.802004]  sda: sda1 sda2 sda3
[    3.806333] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.811618] Waiting for root device PARTUUID=93ffdd41-3e4a-2ac5-91b9-53e979fb5902...
[    4.397974] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[    4.668222] scsi 2:0:0:0: Direct-Access     USB      Disk             2.60 PQ: 0 ANSI: 2
[    4.679170] sd 2:0:0:0: [sdb] 1027072 512-byte logical blocks: (526 MB/502 MiB)
[    4.687586] sd 2:0:0:0: [sdb] Write Protect is off
[    4.693178] sd 2:0:0:0: [sdb] No Caching mode page found
[    4.699141] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    4.712809] GPT:Primary header thinks Alt. header is not at the end of the disk.
[    4.721152] GPT:246304 != 1027071
[    4.724860] GPT:Alternate GPT header not at the end of the disk.
[    4.731586] GPT:246304 != 1027071
[    4.735292] GPT: Use GNU Parted to correct GPT errors.
[    4.741078]  sdb: sdb1 sdb2 sdb128
[    4.746667] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    4.762514] EXT4-fs (sdb2): mounted filesystem without journal. Opts: (null)
[    4.770479] VFS: Mounted root (ext4 filesystem) readonly on device 8:18.
[    4.779326] Freeing unused kernel image (initmem) memory: 1472K
[    4.787547] Write protecting the kernel read-only data: 20480k
[    4.795637] Freeing unused kernel image (text/rodata gap) memory: 2044K
[    4.804366] Freeing unused kernel image (rodata/data gap) memory: 2012K
[    4.811911] Run /sbin/init as init process
[    4.875362] init: Console is alive
[    5.035874] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.052358] pps_core: LinuxPPS API ver. 1 registered
[    5.058001] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    5.071616] PTP clock support registered
[    5.081491] Button Hotplug driver version 0.4.1
[    5.091143] igb: Intel(R) Gigabit Ethernet Network Driver
[    5.097197] igb: Copyright (c) 2007-2014 Intel Corporation.
[    5.135219] pps pps0: new PPS source ptp0
[    5.139848] igb 0000:02:00.0: added PHC on eth0
[    5.144936] igb 0000:02:00.0: Intel(R) Gigabit Ethernet Network Connection
[    5.152640] igb 0000:02:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 00:90:0b:7d:4c:46
[    5.160636] igb 0000:02:00.0: eth0: PBA No: FFFFFF-0FF
[    5.166386] igb 0000:02:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[    5.205519] pps pps1: new PPS source ptp1
[    5.210144] igb 0000:03:00.0: added PHC on eth1
[    5.215215] igb 0000:03:00.0: Intel(R) Gigabit Ethernet Network Connection
[    5.222951] igb 0000:03:00.0: eth1: (PCIe:2.5Gb/s:Width x1) 00:90:0b:7d:4c:47
[    5.230951] igb 0000:03:00.0: eth1: PBA No: FFFFFF-0FF
[    5.236702] igb 0000:03:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[    5.275191] pps pps2: new PPS source ptp2
[    5.279824] igb 0000:04:00.0: added PHC on eth2
[    5.284894] igb 0000:04:00.0: Intel(R) Gigabit Ethernet Network Connection
[    5.292604] igb 0000:04:00.0: eth2: (PCIe:2.5Gb/s:Width x1) 00:90:0b:7d:4c:48
[    5.300598] igb 0000:04:00.0: eth2: PBA No: FFFFFF-0FF
[    5.306347] igb 0000:04:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[    5.317195] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.326504] init: - preinit -
[    5.459103] random: jshn: uninitialized urandom read (4 bytes read)
[    5.495214] random: jshn: uninitialized urandom read (4 bytes read)
[    5.511088] random: jshn: uninitialized urandom read (4 bytes read)
[    5.648595] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    5.817946] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[    9.751938] random: jshn: uninitialized urandom read (4 bytes read)
[    9.780671] mount_root: mounting /dev/root
[    9.788793] EXT4-fs (sdb2): re-mounted. Opts: (null)
[   10.105619] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.166227] procd: - early -
[   10.738158] procd: - ubus -
[   10.751550] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.792150] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.800713] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.807892] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.822524] procd: - init -
Please press Enter to activate this console.
[   10.967799] urngd: v1.0.2 started.
[   10.992106] random: crng init done
[   10.995927] random: 22 urandom warning(s) missed due to ratelimiting
[   11.020285] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.043023] e1000: Intel(R) PRO/1000 Network Driver
[   11.048530] e1000: Copyright (c) 1999-2006 Intel Corporation.
[   11.062501] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[   11.069372] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[   11.078703] i2c /dev entries driver
[   11.106117] e1000e: Intel(R) PRO/1000 Network Driver
[   11.111729] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[   11.121894] Intel(R) 2.5G Ethernet Linux Driver
[   11.126967] Copyright(c) 2018 Intel Corporation.
[   11.157099] PPP generic driver version 2.4.2
[   11.162625] NET: Registered protocol family 24
[   11.170615] kmodloader: done loading kernel modules from /etc/modules.d/*
[   18.578022] 8021q: adding VLAN 0 to HW filter on device eth0
[   18.585974] br-lan: port 1(eth0) entered blocking state
[   18.591866] br-lan: port 1(eth0) entered disabled state
[   18.597887] device eth0 entered promiscuous mode
[   18.639647] 8021q: adding VLAN 0 to HW filter on device eth1

lspci

00:00.0 Host bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series SoC Transaction Register (rev 11)
00:02.0 VGA compatible controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Graphics & Display (rev 11)
00:13.0 SATA controller: Intel Corporation Atom Processor E3800 Series SATA AHCI Controller (rev 11)
00:14.0 USB controller: Intel Corporation Atom Processor Z36xxx/Z37xxx, Celeron N2000 Series USB xHCI (rev 11)
00:1a.0 Encryption controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine (rev 11)
00:1b.0 Audio device: Intel Corporation Atom Processor Z36xxx/Z37xxx Series High Definition Audio Controller (rev 11)
00:1c.0 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 1 (rev 11)
00:1c.1 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 2 (rev 11)
00:1c.2 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 3 (rev 11)
00:1c.3 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 4 (rev 11)
00:1f.0 ISA bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Power Control Unit (rev 11)
00:1f.3 SMBus: Intel Corporation Atom Processor E3800/CE2700 Series SMBus Controller (rev 11)
02:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection (rev 03)
03:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection (rev 03)
04:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection (rev 03)

cpuinfo (1st core out of two)

root@OpenWrt:/etc/config# cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 55
model name      : Intel(R) Atom(TM) CPU  E3825  @ 1.33GHz
stepping        : 9
microcode       : 0x901
cpu MHz         : 533.333
cache size      : 512 KB
physical id     : 0
siblings        : 2
core id         : 0
cpu cores       : 2
apicid          : 0
initial apicid  : 0
fpu             : yes
fpu_exception   : yes
cpuid level     : 11
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb pti tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm arat
vmx flags       : vnmi preemption_timer invvpid ept_x_only flexpriority tsc_offset vtpr mtf vapic ept vpid unrestricted_guest
bugs            : cpu_meltdown spectre_v1 spectre_v2 mds msbds_only mmio_unknown
bogomips        : 2666.66
clflush size    : 64
cache_alignment : 64
address sizes   : 36 bits physical, 48 bits virtual
power management:

[Strykar]

Was this a new or used item?
Place of purchase?

[frollic]

It was used, bought it on US eBay.

[RaylynnKnight]

Can be found on ebay by searching for NCA-1010 or look for devices from Untangle, Star2Star and Silver Peak.

[frollic]

Yup, mine was labeled Star2Star.

[oatja]

Hi frolic and other

Do you have BIOS dumb file? I've Silverpeak but seems bios was corrupt. Also do you have bios password for silverpeak this model?

Thanks

[frollic]

I can create one from my star2star, if you know a way of doing it from Linux.

[mr9v9]

I tried to dump mine using afudos but Bios is write-protected and don't see a way to disable it. Tips?

Do any of you know where to get an updated BIOS file? Lanner support was no help since:

Due to non-disclosure agreement with the customer, we unsuitability offer the BIOS update file for you. We suggest that you should contact your distributor of this unit for further support.

My current version:

[slh]

That's usually the drawback of getting commercial firmware PC hardware, you won't get BIOS updates and in many cases not even any kind of BIOS access to begin with. It either works as-is or it won't.

[oatja]

Please my box is not boot only green light now

[oatja]

That's unfortunate, if someone know how to unprotected please share