Kernel panic after sysupgrade (new device, Beeline smartbox)

For Developers
1

I got this device:

I've made firmware for it based on openwrt master branch.

If i upgrade firmware with sysupgrade i got kernel panic.

Update and boot log:

root@OpenWrt:/tmp# sysupgrade -v openwrt-ramips-mt7621-beeline_smartbox-flash-squashfs-sysupgrade.bin 
Fri Dec 24 20:32:54 UTC 2021 upgrade: Saving config files...
etc/config/dhcp
etc/config/dropbear
etc/config/firewall
etc/config/luci
etc/config/network
etc/config/rpcd
etc/config/system
etc/config/ubootenv
etc/config/ucitrack
etc/config/uhttpd
etc/config/wireless
etc/dropbear/dropbear_ed25519_host_key
etc/dropbear/dropbear_rsa_host_key
etc/fw_env.config
etc/group
etc/hosts
etc/inittab
etc/luci-uploads/.placeholder
etc/opkg/keys/456559476c33fb8f
etc/opkg/keys/b5043e70f9a75cde
etc/passwd
etc/profile
etc/rc.local
etc/shadow
etc/shells
etc/shinit
etc/sysctl.conf
etc/uhttpd.crt
etc/uhttpd.key
etc/uhttpd.key
etc/uhttpd.crt
Fri Dec 24 20:32:55 UTC 2021 upgrade: Commencing upgrade. Closing all shell sessions.
[  166.384122] device wlan0 left promiscuous mode
[  166.393301] br-lan: port 3(wlan0) entered disabled state
Watchdog handover: fd=3
- watchdog -
Watchdog does not have CARDRESET support
[  166.491730] device wlan1 left promiscuous mode
[  166.500880] br-lan: port 4(wlan1) entered disabled state
Fri Dec 24 20:32:56 UTC 2021 upgrade: Sending TERM to remaining processes ...
Fri Dec 24 20:32:56 UTC 2021 upgrade: Sending signal TERM to ntpd (2321)
Fri Dec 24 20:32:56 UTC 2021 upgrade: Sending signal TERM to ntpd (2372)
Fri Dec 24 20:33:00 UTC 2021 upgrade: Sending KILL to remaining processes ...
[  177.140419] sh (3318): drop_caches: 3
Fri Dec 24 20:33:06 UTC 2021 upgrade: Switching to ramdisk...
[  180.241606] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[  180.269397] UBIFS (ubi0:1): un-mount UBI device 0
Fri Dec 24 20:33:09 UTC 2021 upgrade: Performing system upgrade...
Unlocking kernel ...

Writing from <stdin> to kernel ...  [ ][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w]    
removing ubiblock0_0
[  190.263812] block ubiblock0_0: released
Volume ID 0, size 32 LEBs (4063232 bytes, 3.8 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 77455360
Volume ID 1, size 610 LEBs (77455360 bytes, 73.8 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
[  192.395021] UBIFS (ubi0:1): default file-system created
[  192.406795] UBIFS (ubi0:1): Mounting in unauthenticated mode
[  192.418401] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 4026
[  192.543243] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[  192.558916] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[  192.578665] UBIFS (ubi0:1): FS size: 76185600 bytes (72 MiB, 600 LEBs), journal size 3809280 bytes (3 MiB, 30 LEBs)
[  192.599447] UBIFS (ubi0:1): reserved for root: 3598434 bytes (3514 KiB)
[  192.612638] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID A34CF210-54A6-40D8-AD48-EC8928E6FB68, small LPT model
[  192.660816] UBIFS (ubi0:1): un-mount UBI device 0
[  192.670249] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
sysupgrade successful
umount: can't unmount /dev: Resource busy
umoun[  192.704192] reboot: Restarting system
t: can't unmount /tmp: Resource busy
CkokoCoc0

)
);CgCHH
FLLLXY^)8
<
gJs9S(O99
JNXJ9JMh
!zJJH!
X
*LJKXSHN
X
*LL
HHsH1D1*KJ
99!1*KXSHJ

xX
!
HHLX{+rprintk: console [ttyS0] enabled
[    0.614144] printk: console [ttyS0] enabled
[    0.630629] printk: bootconsole [early0] disabled
[    0.630629] printk: bootconsole [early0] disabled
[    0.651459] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[    0.666330] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
[    0.678982] nand: Winbond W29N01HV
[    0.685755] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.700826] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[    0.713863] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[    0.728415] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[    0.742962] Scanning device for bad blocks
[    1.394912] 15 fixed-partitions partitions found on MTD device mt7621-nand
[    1.408599] Creating 15 MTD partitions on "mt7621-nand":
[    1.419180] 0x000000000000-0x000007f80000 : "all"
[    1.429887] 0x000000000000-0x000000100000 : "bootloader"
[    1.441504] 0x000000100000-0x000000200000 : "config"
[    1.452314] 0x000000200000-0x000000300000 : "factory"
[    1.463398] 0x000000300000-0x000002300000 : "kernel_stock"
[    1.475511] 0x000000720000-0x000002300000 : "rootfs_stock"
[    1.487464] 0x000002300000-0x000004300000 : "kernel"
[    1.498443] 0x000002720000-0x000004300000 : "rootfs2"
[    1.509518] 0x000004300000-0x000004500000 : "glbcfg"
[    1.520383] 0x000004500000-0x000004600000 : "board_data"
[    1.531888] 0x000004600000-0x000004800000 : "glbcfg2"
[    1.542849] 0x000004800000-0x000004900000 : "board_data2"
[    1.554540] 0x000004900000-0x000007f80000 : "data"
[    1.565220] 0x000002720000-0x000004300000 : "ubipart0"
[    1.576539] 0x000004600000-0x000007f80000 : "ubipart1"
[    1.596752] Concatenating MTD devices:
[    1.604282] (0): "ubipart0"
[    1.609836] (1): "ubipart1"
[    1.615405] into device "ubi-concat"
[    1.622556] 1 fixed-partitions partitions found on MTD device ubi-concat
[    1.635911] Creating 1 MTD partitions on "ubi-concat":
[    1.646157] 0x000000000000-0x000005280000 : "ubi"
[    1.659457] libphy: Fixed MDIO Bus: probed
[    1.704050] libphy: mdio: probed
[    1.710796] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.725444] mtk_soc_eth 1e100000.ethernet: generated random MAC address c6:47:a5:c0:79:e2
[    1.742529] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    1.762221] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[    1.775637] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
[    1.793205] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
[    1.809503] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
[    1.825901] mt7621-pci 1e140000.pcie: Parsing DT failed
[    1.838529] NET: Registered protocol family 10
[    1.848854] Segment Routing with IPv6
[    1.856296] NET: Registered protocol family 17
[    1.865498] 8021q: 802.1Q VLAN Support v1.8
[    1.877127] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.901570] libphy: dsa slave smi: probed
[    1.911030] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL)
[    1.931035] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL)
[    1.951019] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL)
[    1.971739] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    1.988679] DSA: tree 0 setup
[    1.994935] rt2880-pinmux pinctrl: pcie is already enabled
[    2.005971] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[    2.019339] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
[    2.036878] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
[    2.053187] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
[    2.069569] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    2.084676] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    2.099669] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[    2.214265] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    2.225382] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    2.336639] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[    2.350502] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    2.364377] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    2.374097] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    2.392794] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    2.405490] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    2.419193] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    2.432890] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.443826] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[    2.464146] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    2.476130] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.488623] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[    2.501171] pci 0000:00:00.0: supports D1
[    2.509160] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.522258] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[    2.534319] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    2.548367] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
[    2.561019] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    2.591952] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    2.602410] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    2.614562] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.628085] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.642476] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.655705] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.668882] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.682753] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.696282] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.710669] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[    2.724208] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    2.737743] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.752314] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.762206] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    2.775732] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.789260] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.805717] UBI error: no valid UBI magic found inside mtd15
[    2.817722] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    2.831896] /dev/root: Can't open blockdev
[    2.840115] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    2.855062] Please append a correct "root=" boot option; here are the available partitions:
[    2.871702] 1f00          130560 mtdblock0 
[    2.871707]  (driver?)
[    2.884729] 1f01            1024 mtdblock1 
[    2.884734]  (driver?)
[    2.897736] 1f02            1024 mtdblock2 
[    2.897740]  (driver?)
[    2.910744] 1f03            1024 mtdblock3 
[    2.910749]  (driver?)
[    2.923764] 1f04           32768 mtdblock4 
[    2.923769]  (driver?)
[    2.936770] 1f05           28544 mtdblock5 
[    2.936775]  (driver?)
[    2.949777] 1f06           32768 mtdblock6 
[    2.949782]  (driver?)
[    2.962785] 1f07           28544 mtdblock7 
[    2.962789]  (driver?)
[    2.975804] 1f08            2048 mtdblock8 
[    2.975809]  (driver?)
[    2.988812] 1f09            1024 mtdblock9 
[    2.988817]  (driver?)
[    3.001819] 1f0a            2048 mtdblock10 
[    3.001824]  (driver?)
[    3.015012] 1f0b            1024 mtdblock11 
[    3.015017]  (driver?)
[    3.028194] 1f0c           55808 mtdblock12 
[    3.028199]  (driver?)
[    3.041373] 1f0d           28544 mtdblock13 
[    3.041378]  (driver?)
[    3.054567] 1f0e           58880 mtdblock14 
[    3.054572]  (driver?)
[    3.067745] 1f0f           84480 mtdblock15 
[    3.067750]  (driver?)
[    3.080926] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    3.097389] Rebooting in 1 seconds..
CkokoCoc0

What is wrong?

1 Like
2

Do original openwrt firmware (from which you start sysupgrade) have the same flash layout?

3

If you used upgrade was it already running OpenWRT? EDIT: I see from the first command line that you did - what was it?

Maybe try a factory image.

Do you have serial logs of what was there before booting?

4

mtd write kernel and rootfs. This method also works well with OpenWRT now.

Full log:

xX
!
HHLX{+rprintk: console [ttyS0] enabled
[    0.614725] printk: console [ttyS0] enabled
[    0.631212] printk: bootconsole [early0] disabled
[    0.631212] printk: bootconsole [early0] disabled
[    0.652220] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[    0.667130] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
[    0.679785] nand: Winbond W29N01HV
[    0.686561] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.701634] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[    0.714677] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[    0.729231] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[    0.743785] Scanning device for bad blocks
[    1.395758] 15 fixed-partitions partitions found on MTD device mt7621-nand
[    1.409447] Creating 15 MTD partitions on "mt7621-nand":
[    1.420026] 0x000000000000-0x000007f80000 : "all"
[    1.430831] 0x000000000000-0x000000100000 : "bootloader"
[    1.442474] 0x000000100000-0x000000200000 : "config"
[    1.453333] 0x000000200000-0x000000300000 : "factory"
[    1.464442] 0x000000300000-0x000002300000 : "kernel_stock"
[    1.476633] 0x000000720000-0x000002300000 : "rootfs_stock"
[    1.488654] 0x000002300000-0x000004300000 : "kernel"
[    1.499679] 0x000002720000-0x000004300000 : "rootfs2"
[    1.510827] 0x000004300000-0x000004500000 : "glbcfg"
[    1.521690] 0x000004500000-0x000004600000 : "board_data"
[    1.533248] 0x000004600000-0x000004800000 : "glbcfg2"
[    1.544346] 0x000004800000-0x000004900000 : "board_data2"
[    1.556037] 0x000004900000-0x000007f80000 : "data"
[    1.566786] 0x000002720000-0x000004300000 : "ubipart0"
[    1.578184] 0x000004600000-0x000007f80000 : "ubipart1"
[    1.598344] Concatenating MTD devices:
[    1.605882] (0): "ubipart0"
[    1.611434] (1): "ubipart1"
[    1.616998] into device "ubi-concat"
[    1.624167] 1 fixed-partitions partitions found on MTD device ubi-concat
[    1.637519] Creating 1 MTD partitions on "ubi-concat":
[    1.647759] 0x000000000000-0x000005280000 : "ubi"
[    1.661185] libphy: Fixed MDIO Bus: probed
[    1.704596] libphy: mdio: probed
[    1.711425] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.726067] mtk_soc_eth 1e100000.ethernet: generated random MAC address 6e:c0:8f:dd:dc:6e
[    1.743230] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    1.763040] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[    1.776456] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
[    1.793995] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
[    1.810294] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
[    1.826685] mt7621-pci 1e140000.pcie: Parsing DT failed
[    1.839320] NET: Registered protocol family 10
[    1.849653] Segment Routing with IPv6
[    1.857139] NET: Registered protocol family 17
[    1.866330] 8021q: 802.1Q VLAN Support v1.8
[    1.877894] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.902245] libphy: dsa slave smi: probed
[    1.911752] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL)
[    1.931802] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL)
[    1.951863] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL)
[    1.972639] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    1.989628] DSA: tree 0 setup
[    1.995865] rt2880-pinmux pinctrl: pcie is already enabled
[    2.006876] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[    2.020236] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
[    2.037768] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
[    2.054064] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
[    2.070437] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    2.085536] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    2.100508] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[    2.215086] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    2.226201] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    2.337439] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[    2.351298] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    2.365165] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    2.374879] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    2.393564] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    2.406247] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    2.419943] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    2.433633] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.444570] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[    2.464883] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    2.476862] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.489345] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[    2.501888] pci 0000:00:00.0: supports D1
[    2.509872] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.522946] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[    2.534986] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    2.549030] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
[    2.561673] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    2.592598] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    2.603034] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    2.615175] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.628693] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.643079] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.656301] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.669473] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.683337] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.696860] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.711247] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[    2.724780] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    2.738303] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.752866] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.762752] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    2.776273] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.789794] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.806418] UBI: auto-attach mtd15
[    2.813210] ubi0: attaching mtd15
[    2.820163] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    3.656979] ubi0: scanning is finished
[    3.681301] ubi0: attached mtd15 (name "ubi", size 82 MiB)
[    3.692255] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.705961] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.719474] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.733325] ubi0: good PEBs: 660, bad PEBs: 0, corrupted PEBs: 0
[    3.745291] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    3.759670] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1115951597
[    3.777858] ubi0: available PEBs: 0, total reserved PEBs: 660, PEBs reserved for bad PEB handling: 14
[    3.796249] ubi0: background thread "ubi_bgt0d" started, PID 442
[    3.798856] block ubiblock0_0: created from ubi0:0(rootfs)
[    3.819202] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    3.840255] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    3.858703] Freeing unused kernel memory: 1276K
[    3.867763] This architecture does not have kernel memory protection.
[    3.880598] Run /sbin/init as init process
[    4.463086] init: Console is alive
[    4.470348] init: - watchdog -
[    5.240287] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.341482] usbcore: registered new interface driver usbfs
[    5.352570] usbcore: registered new interface driver hub
[    5.363312] usbcore: registered new device driver usb
[    5.383832] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[    5.398861] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
[    5.414199] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    5.424833] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    5.453886] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[    5.472159] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[    5.484641] hub 1-0:1.0: USB hub found
[    5.492256] hub 1-0:1.0: 2 ports detected
[    5.500853] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    5.511544] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    5.526488] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[    5.539350] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.556272] hub 2-0:1.0: USB hub found
[    5.563873] hub 2-0:1.0: 1 port detected
[    5.579159] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.614104] init: - preinit -
[    6.515539] random: jshn: uninitialized urandom read (4 bytes read)
[    6.595051] random: jshn: uninitialized urandom read (4 bytes read)
[    7.105459] random: jshn: uninitialized urandom read (4 bytes read)
[    7.373089] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    7.389217] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    7.394261] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[    7.419550] 8021q: adding VLAN 0 to HW filter on device lan1
[    7.433482] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.638056] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   11.653130] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[   11.669718] UBIFS (ubi0:1): default file-system created
[   11.681477] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   11.693065] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 580
[   11.820184] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.835804] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.855542] UBIFS (ubi0:1): FS size: 76185600 bytes (72 MiB, 600 LEBs), journal size 3809280 bytes (3 MiB, 30 LEBs)
[   11.876322] UBIFS (ubi0:1): reserved for root: 3598434 bytes (3514 KiB)
[   11.889492] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID C63EA66D-35CC-4923-BDCA-6E6B4393A3C5, small LPT model
[   11.915638] mount_root: overlay filesystem has not been fully initialized yet
[   11.930687] mount_root: switching to ubifs overlay
[   11.948820] urandom-seed: Seed file not found (/etc/urandom.seed)
[   12.121236] mt7530 mdio-bus:1f lan1: Link is Down
[   12.140706] procd: - early -
[   12.146763] procd: - watchdog -
[   12.803909] procd: - watchdog -
[   12.810807] procd: - ubus -
[   12.982413] procd: - init -
Please press Enter to activate this console.
[   13.754284] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.976152] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb
[   13.991085] Backport generated by backports.git v5.15.8-1-0-g83f664bb
[   14.006907] urngd: v1.0.2 started.
[   14.038977] xt_time: kernel timezone is -0000
[   14.188835] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[   14.194997] random: crng init done
[   14.199648] pci 0000:00:00.0: enabling device (0006 -> 0007)
[   14.206371] random: 7 urandom warning(s) missed due to ratelimiting
[   14.217626] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[   14.276602] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[   14.276602] 
[   14.282717] PPP generic driver version 2.4.2
[   14.306990] NET: Registered protocol family 24
[   14.351160] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.550701] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[   14.676129] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[   45.879883] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   45.900435] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   45.916734] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   45.919641] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[   45.947376] 8021q: adding VLAN 0 to HW filter on device lan1
[   45.962232] br-lan: port 1(lan1) entered blocking state
[   45.973130] br-lan: port 1(lan1) entered disabled state
[   45.984447] device lan1 entered promiscuous mode
[   45.993797] device eth0 entered promiscuous mode
[   46.006678] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   46.045266] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[   46.059069] 8021q: adding VLAN 0 to HW filter on device lan2
[   46.074542] br-lan: port 2(lan2) entered blocking state
[   46.084994] br-lan: port 2(lan2) entered disabled state
[   46.096483] device lan2 entered promiscuous mode
[   46.123779] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[   46.137501] 8021q: adding VLAN 0 to HW filter on device wan
[   47.574396] br-lan: port 3(wlan0) entered blocking state
[   47.585098] br-lan: port 3(wlan0) entered disabled state
[   47.596556] device wlan0 entered promiscuous mode
[   47.693621] br-lan: port 4(wlan1) entered blocking state
[   47.704367] br-lan: port 4(wlan1) entered disabled state
[   47.715767] device wlan1 entered promiscuous mode
[   47.725732] br-lan: port 4(wlan1) entered blocking state
[   47.736439] br-lan: port 4(wlan1) entered forwarding state
[   47.747949] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   47.898555] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   47.911770] br-lan: port 3(wlan0) entered blocking state
[   47.922514] br-lan: port 3(wlan0) entered forwarding state
[   48.017406] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   49.175541] mt7530 mdio-bus:1f lan1: Link is Up - 10Mbps/Full - flow control off
[   49.190398] br-lan: port 1(lan1) entered blocking state
[   49.200851] br-lan: port 1(lan1) entered forwarding state
[   51.254352] mt7530 mdio-bus:1f lan1: Link is Down
[   51.263898] br-lan: port 1(lan1) entered disabled state
[   53.334890] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   53.349878] br-lan: port 1(lan1) entered blocking state
[   53.360318] br-lan: port 1(lan1) entered forwarding state



BusyBox v1.34.1 (2021-12-24 02:27:11 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r18395-4ca736c27d
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------

root@OpenWrt:/#
1 Like
5

Sure the same.

1 Like
6

Something wrong with sysupgrade image. Pls, show files and its types of sysupgrade image (usually it's simple tar archive with kernel.bin, squashfs.bin and contol file).

7

in case you haven't spotted it the first lines that differ are:

UBI: auto-attach mtd15
ubi0: attaching mtd15

vs:
UBI error: no valid UBI magic found inside mtd15

I have no idea how to address that :slight_smile:, but there are other threads with the same error message in them.

8

It is.

1 Like
9

Something wrong with sysupgrade scripts. At least because no error message while upgrading.

1 Like
10

this my friend appears to be a considerable error message (edit: ok rereading this appears to be spat out after reset apologies) ... and yes, i'd agree its in the sysupgrade write logic/process (but your layout could be an influencing factor here - if everything is 100% normal / as expected... then compare images(size?) / upgrade logic for any changes, if not that then go back to ubi stuff maybe)

11

ok. That's what i meant. There is no critical error for sysupgrade. What to do?

1 Like
12

if its master... maybe best to checkout some older commit or look at that ubi search suggested to see if there is a noticable date occurence...

13

Adware detected :slight_smile:
another free hosting?

14

yep. you've asked for sysupgrade bin

1 Like
15

I don't think so. If I'm not mistaken your sysupgrade image contain ubinized rootfs file.
Modify image build script (in mt761.mk) to use raw squashfs image for rootfs.
In this case sysupgrade script make correct ubifs in mtd15 partition itself.

16

What line i need to modify?

Now i got this:

   UBINIZE_OPTS := -E 5
   BLOCKSIZE := 128k
   PAGESIZE := 2048
   KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none \
	| pad-to 16805860 | beeline_smartbox-flash_firmware-header
   KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | uImage none
   IMAGES += kernel.bin rootfs.bin
   IMAGE/kernel.bin := append-kernel
   IMAGE/rootfs.bin := append-ubi | check-size
   IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
1 Like
17

This step:

   IMAGE/rootfs.bin := append-ubi | check-size

convert raw squashfs root image into raw ubinized rootfs.
Try to remove it. Or just for quick test simply replace root file in archive with squashfs root file.

18

The problem is sysupgrade but not rootfs image. With your proposal i just haven't got rootfs file.

This way upgrade is working well:

mtd write kernel.bin /dev/mtd6 && mtd write squashfs-rootfs.bin /dev/mtd13