Juplink RX4-1800 (AX1800)

cdes · May 29, 2022, 7:44pm

Hi, was bored and quickly obtained a boot log from one of the $25 WiFi6 routers I picked up at Amazon. Maybe it helps someone looking into compatibility and/or development.

----
BTRM
V1.3
MEM?
MEMP
CACH
CODE
ZBSS
MAIN
OTP?
OTPP
USBT
SNAN
IMG?
IMGL
UHD?
UHDP
RLO?
RLOP
UBI?
UBIP
PASS
HELO
CPU0
L1CD
MMUI
ZBBS
MAIN
5.0207-1.0.38-163.231
SEND
Boot Strap Register:  0x7ffffb6f
NVRAM memcfg 0x1327
MCB chksum 0x7081f938, config 0x1327

MemsysInit hpg0_generic 3.3.1.0 20180919
DDR3
8521E6A8 80180000 801A0000 00000000 00000000 00405945
MCB rev=0x00000501 Ref ID=0x05945 Sub Bld=0x004
Dram Timing 11-11-11

start of memsys_begin
mc_cfg_init(): Initialize the default values on mc_cfg
init_memc_dram_profile(): Initializing MEMC DRAM profile
---------------------------------------------------------------
MEMC DRAM profile (memc_dram_profile_struct) values:
  dram_type    = DDR3
====================================================
PART values:
  part_speed_grade    = 1600 CL11
  part_size_Mbits     = 2048 (DRAM size in MegaBits)
  part_row_bits       = 14 (number of row bits)
  part_col_bits       = 10 (number of column bits)
  part_ba_bits        = 3 (number of bank bits)
  part_width_bits     = 16 (DRAM width in bits)
NUMER OF PARTS:
  part_num            = 1 (Number of parts)
TOTAL values:
  total_size_Mbits    = 2048 (DRAM size in MegaBits)
  total_cs_bits       = 0 (number of cs bits, for dual_rank mode)
  total_width_bits    = 16 (DRAM width in bits)
  total_burst_bytes   = 16 (Number of bytes per DRAM access)
  total_max_byte_addr = 0xfffffff (Maximum/last DRAM byte address)
                        (Number of bits in total_max_byte_addr is 28)
                        (i.e. total_max_byte_addr goes from bit 0 to bit 27)
  ddr_2T_mode         = 0
  ddr_hdp_mode        = 0
  large_page          = 1
  ddr_dual_rank       = 0
  cs_mode             = 0
MEMC timing (memc_dram_timing_cfg_struct) values:
====================================================
  MC_CHN_TIM_TIM1_0 register fields:
    tCwl   = 8
    tRP    = 11
    tCL    = 11
    tRCD   = 11
  MC_CHN_TIM_TIM1_1 register fields:
    tCCD_L = 4
    tCCD   = 4
    tRRD_L = 6
    tRRD   = 6
  MC_CHN_TIM_TIM1_2 register fields:
    tFAW   = 32
    tRTP   = 6
    tRCr   = 39
  MC_CHN_TIM_TIM1_3 register fields:
    tWTR_L = 6
    tWTR   = 6
    tWR_L  = 12
    tWR    = 12
  MC_CHN_TIM_TIM2 register fields:
    tR2R   = 0
    tR2W   = 2
    tW2R   = 2
    tW2W   = 0
    tAL    = 0
    tRFC   = 128
====================================================
%1 SSC enabled

Poll PHY Status register
PHY Status= 1
Disable Auto-Refresh
[0x80180200] = 0x00000305
End of memsys_begin
Add/Ctl Alignment
Coarse Adj=0x087 deg, cmd steps=0x0DC
reg 0x801A0090 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A0094 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A0098 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A009C set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00A0 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00A4 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00A8 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00AC set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00B0 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00B4 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00B8 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00BC set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00C0 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00C4 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00C8 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00CC set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00D0 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00D4 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00D8 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00DC set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00E0 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00E4 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00E8 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00EC set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00F0 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00F4 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00F8 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A00FC set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A0100 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A0108 set to VDL 0x054 with Fine Adj=0x01 deg
reg 0x801A010C set to VDL 0x054 with Fine Adj=0x01 deg
HP RX TRIM
itrim = 0x0
lstrim = 0xA

ZQ Cal HP PHY
 R in Ohm
 P: Finger=0x364 Term=0x7C Drv=0x27
 N: Finger=0x311 Term=0x70 Drv=0x27

PLL Ref(Hz)=0x02FAF080 UI STEPS=0x06E
 DDR CLK(MHz)=0x307 WL CLK dly(ps)=0x0C8 bitT(ps)=0x285 VDLsize(fs)=0x16E7 CLK_VDL=0x022
start of memc_init
[0x80180004] = 0x0110061f
[0x80180234] = 0x00000101
Enable Auto-Refresh
[0x80180110] = 0x11100f0e
[0x80180114] = 0x15141312
[0x80180118] = 0x19181716
[0x8018011c] = 0x00001b1a
[0x80180124] = 0x04000000
[0x80180128] = 0x08070605
[0x8018012c] = 0x00000a09
[0x80180134] = 0x000d0c0b
 Writing to MC_CHN_CFG_CNFG reg; data=0x00000000
[0x80180100] = 0x00000000
cfg_memc_timing_ctrl() Called
[0x80180214] = 0x080b0b0b
[0x80180218] = 0x04040606
[0x8018021c] = 0x20000627
[0x80180220] = 0x06060c0c
[0x80180224] = 0x12000080
End of memc_init
start of pre_shmoo
[0x80180004] = 0xc110071f
end of pre_shmoo

SHMOO 28nm
801A0000 801A0000 00000000 00020000 00000000

Shmoo WL

One UI Steps : 0x7B

auto-clk result = 026 (filter=0C steps)
initial CLK shift = 022
final CLK shift   = 026

   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 S---------------X----------------------------------------------------------------------------------------------------------
01 S----------X---------------------------------------------------------------------------------------------------------------

Shmoo RD En
FORCED WR ODT = 0x00001800
 DQSN DRIVE PAD CONTROL (from) (to)
 B0 00039ED4 00079ED4
 B1 00039ED4 00079ED4
B0 RISE UI=1 VDL=25 PICK UI=2 VDL=25
B1 RISE UI=1 VDL=23 PICK UI=2 VDL=23
   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 --S-------------------------------++-X+++++++++++++++----------------------------------------------------------------------
01 --S--------------------------------X+++++++++++++++------------------------------------------------------------------------

Shmoo RD DQ NP
DQS :
B0 VDL=6E ok
B1 VDL=6E ok
   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 -----------------------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++---------
01 ----------+++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++-----------------
02 ------------------------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-----
03 ---------------------++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++------------
04 ------------------+-++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++---------
05 -----------------+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++--------------
06 -----------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++-------------
07 ---------------------++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++-------------
08 -----------------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++-------
09 ----------+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------------
10 -----------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++-------------
11 ---------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------------
12 ----------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++--------------
13 ----------+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------------
14 ----------------+++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++------------
15 -----------------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++---------------

Shmoo RD DQ P
   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 ------------------------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-----
01 -----------+++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++----------------
02 ---------------------++++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++++----
03 ---------------------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++-----------
04 ------------------++++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++--------
05 -----------------+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++--------------
06 ----------------+++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++-----------
07 ---------------------++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++-------------
08 -------------------+++++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++++-----
09 ----------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-------------------
10 ----------------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-------------
11 -------++++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++-------------------
12 -------------+++++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++++-----------
13 --------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++---------------------
14 --------------++++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++++-----------
15 -----------------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++---------------

Shmoo RD DQ N
   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 -----------------------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++---------
01 ---------++++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++-----------------
02 ------------------------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-----
03 ---------------------++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++------------
04 ------------------+++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++---------
05 ----------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++--------------
06 ----------------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-------------
07 --------------------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++------------
08 -----------------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++-------
09 -----------+++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++---------------------
10 ------------------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-----------
11 ---------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------------
12 ----------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++--------------
13 ---------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------------
14 -----------------+++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-----------
15 -----------------+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++--------------

RD DQS adjustments :
BL0: Start: 0x6E Final: 0x6E
BL1: Start: 0x6E Final: 0x6E

Shmoo WR DQ
   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 ---------------+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++----------------
01 -++++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++++-------------------------
02 ------------+++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++----------------
03 --------------++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++--------------------
04 --------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++---------------------
05 ----------+++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++--------------------------
06 -------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++----------------------
07 ------------++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++---------------------
08 ---------------++++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------
09 ----+++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++++---------------------------
10 -----------++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++-----------------------
11 ---+++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-------------------------
12 ----------++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++-------------------
13 -++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++----------------------------
14 ----------+++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++------------------
15 ------------++++++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++++----------------------

Shmoo WR DM
WR DM
   000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000011111111111111111111111
   000000000011111111112222222222333333333344444444445555555555666666666677777777778888888888999999999900000000001111111111222
   012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456789012
00 -++++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++++------------------------
01 ++++++++++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++++++++++-------------------------
start of memsys_end
[0x80180004] = 0x8110071f
[0x80180010] = 0x00000008
end of memsys_end
DDR test done successfully
FPS0
----
PAR1
U998
COM0
UBI#
03E6
BT98
0008
----
PAR2
U999
COM1
UBI#
03E7
BT99
0384
----
TRY2
NAN3
UBI!
NAN5


Base: 5.2_07p1
CFE version 1.0.38-163.243 for BCM947622 (32bit,SP,LE)
Build Date: Oct 21 2020 15:06:57 (hujiaqi@localhost.localdomain)
Copyright (C) 2000-2015 Broadcom Corporation.

SEND
Boot Strap Register:  0x7ffffb6f
Chip ID: BCM6755_A1, ARM Cortex A7 Quad Core: 1500MHz
Total Memory: 268435456 bytes (256MB)
SPI NAND ECC 1, page size 0x800 bytes, spare size used 64 bytes
SPI NAND flash device: Winbond W25N01GV, id 0xefaa2100 block 128KB size 131072KB
Take PMC out of reset
waiting for PMC finish booting
PMC rev: 3.0.8.248436 running
pmc_init:PMC using DQM mode
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host/tftp (f/h/c)  : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name    :
Default ramdisk store address     :
Default DTB file name             :
Board Id                          : 96755REF1P900
Number of MAC Addresses (1-64)    : 1
Base MAC Address                  : 8c:0e:60:02:73:00
PSI Size (1-512) KBytes           : 48
Enable Backup PSI [0|1]           : 1
System Log Size (0-256) KBytes    : 0
Auxillary File System Size Percent: 0
WLan Feature                      : 0x00
Partition 1 Size (MB)             : 4M
Partition 2 Size (MB)             : 20M
Partition 3 Size (MB)             : 0M
Partition 4 Size (MB) (Data)      : 8M

Initalizing switch low level hardware.
sysport1 - RGMII - 1.8v InternalDelay:(Tx-0 Rx-0) ...Done
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (address 0x03000000, flash offset 0x03000000) ...
ubi_find_file: got vmlinux.lz  size 2960587
Decompression LZMA Image OK!
Entry at 0x00018000
Starting program at 0x00018000
cfe_fs_fetch_file: file 96755REF1P900.dtb not found
ubi_find_file: got 947622.dtb  size 4444
/memory = 0x10000000 bytes @ 0x0
Setting ROOTFS: root=/dev/ubiblock0_0 ubi.mtd=0 ubi.block=0,0 rootfstype=squashfs
CFE appending "isolcpus=3" from PROFILE to boot cmdline
Appending CFE version to dtb, ret:0
Appending NVRAM to dtb, ret:0
Booting Linux on physical CPU 0x0
Linux version 4.1.52 (hujiaqi@localhost.localdomain) (gcc version 5.5.0 (Buildroot 2017.11.1) ) #1 SMP PREEMPT Wed Oct 21 15:21:53 CST 2020
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Broadcom BCM947622
bootconsole [earlycon0] enabled
Memory policy: Data cache writealloc
On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat c07f9bc0, node_mem_map cfdf8000
  Normal zone: 512 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 65536 pages, LIFO batch:15
PERCPU: Embedded 11 pages/cpu @cfdc6000 s15372 r8192 d21492 u45056
pcpu-alloc: s15372 r8192 d21492 u45056 alloc=11*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: isolcpus=3 root=/dev/ubiblock0_0 ubi.mtd=0 ubi.block=0,0 rootfstype=squashfs console=ttyAMA0 earlyprintk debug irqaffinity=0 pci=pcie_bus_safe
log_buf_len individual max cpu contribution: 4096 bytes
log_buf_len total cpu_extra contributions: 12288 bytes
log_buf_len min size: 16384 bytes
log_buf_len: 32768 bytes
early log buf free: 14892(90%)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 250188K/262144K available (4835K kernel code, 1714K rwdata, 1312K rodata, 208K init, 294K bss, 11956K reserved, 0K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
    lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0018000 - 0xc06190f8   (6149 kB)
      .init : 0xc061a000 - 0xc064e000   ( 208 kB)
      .data : 0xc064e000 - 0xc07fa880   (1715 kB)
       .bss : 0xc07fa880 - 0xc084408c   ( 295 kB)
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
Architected cp15 timer(s) running at 50.00MHz (phys).
clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
Switching to timer-based delay loop, resolution 20ns
BRCM Legacy Drivers' Helper, all legacy drivers' IO memories/interrupts should be remapped here
     Remapping interrupts...
             hwirq      virq
               60        20
               61        21
               43        22
               44        23
               45        24
               46        25
               66        26
              110        27
               69        28
              152        29
              153        30
              154        31
              155        32
              156        33
              157        34
              158        35
              159        36
               78        37
               79        38
               80        39
               81        40
               82        41
               83        42
               84        43
               85        44
              104        45
              105        46
              106        47
              128        48
              129        49
              130        50
              131        51
              132        52
              133        53
              134        54
              135        55
              136        56
              137        57
              138        58
              139        59
              148        60
     Remapping IO memories...
             phys              virt          size
       0000000080180000  00000000d0840000  00024000
       0000000080200000  00000000d0c00000  00200000
       00000000ff800000  00000000d0820000  00013000
       00000000ff810000  00000000d0880000  0004b000
       00000000ffe00000  00000000d0a00000  00100000
       00000000ff860000  00000000d0808000  00002000
       0000000083010a00  00000000d0802a00  00000100
       000000008000c000  00000000d0810000  00003fff
       0000000083010000  00000000d080c000  00001000
       0000000083018000  00000000d080e000  00001000
       0000000083020000  00000000d0816000  00001000
       0000000083028000  00000000d0818000  00001000
       0000000083030000  00000000d081a000  00001000
       0000000083038000  00000000d081c000  00001000
       0000000083040000  00000000d081e000  00001000
       0000000083050000  00000000d0834000  00001000
       0000000083058000  00000000d0836000  00001000
       0000000083048000  00000000d0838000  00001000
       00000000810a0000  00000000d083a000  00001000
       0000000081060000  00000000d083c000  00003000
       00000000ffff0000  00000000d0866000  00001000
       0000000083000000  00000000d0868000  00001000
       000000008306c000  00000000d086a000  00001000
       0000000080400000  00000000d08e0000  00013000
       0000000080500000  00000000d0900000  00013000
       0000000081100000  00000000d0f00000  00091000
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=50000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
--Kernel Config--
  SMP=1
  PREEMPT=1
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x182c0 - 0x182f4
     Reserved memory mapping...
                phys          virt       size
CCI hardware cache coherency enabled
pmc_init:PMC using DQM mode
Successfully retrieved NVRAM data from dtb
cfe-v: 1.0.38-163.231
Brought up 4 CPUs
SMP: Total of 4 processors activated (400.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 1024 (order: 4, 65536 bytes)
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
Serial: AMBA PL011 UART driver
ff812000.serial: ttyAMA0 at MMIO 0xff812000 (irq = 63, base_baud = 0) is a PL011 rev3
console [ttyAMA0] enabled
console [ttyAMA0] enabled
bootconsole [earlycon0] disabled
bootconsole [earlycon0] disabled
Broadcom Logger v0.1
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skb_free_task created successfully with start budget 128
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v1.0 initialized
Broadcom GBPM v0.1 initialized
Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
default registered
default registered
MPTCP: Stable release v0.91
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) (SUMMARY)  � 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
io scheduler noop registered (default)
brd: module loaded
loop: module loaded
SPI NAND Device Linux Registration
SPI NAND Linux Registration
SPI NAND device reset
SPI NAND device Winbond W25N01GV
   device id    = 0xefaa210
   ecc          = 1/1 bits
   page size    = 0x800 (2048) bytes
   block size   = 0x20000 (131072) bytes
   total blocks = 0x400 (1024)
   total size   = 0x8000000 (134217728) bytes
nand: device found, Manufacturer ID: 0x00, Chip ID: 0x00
nand: Unknown ; set by driver
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
>>>>> For primary mtd partition rootfs, cferam/vmlinux.lz UBI volume, vmlinux fs mounted as squash fs on UBI <<<<<
Secondary mtd partition rootfs_update detected as UBI for cferam/vmlinux source and squash fs on UBI for vmlinux filesystem
Creating 8 MTD partitions on "Winbond W25N01GV":
0x000003000000-0x000005f00000 : "rootfs"
0x000000100000-0x000003000000 : "rootfs_update"
0x000007700000-0x000007f00000 : "data"
0x000000000000-0x000000100000 : "nvram"
0x000000100000-0x000003000000 : "image_update"
0x000003000000-0x000005f00000 : "image"
0x000006300000-0x000007700000 : "plugin"
0x000005f00000-0x000006300000 : "misc1"

cdes · May 29, 2022, 7:45pm

part II:

tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
bcm96xxx-wdt ff800480.watchdog: Broadcom BCM96xxx watchdog timer
brcmboard registered
brcmboard: brcm_board_init entry
set_region_info: init region code:0x3000
print_rst_status: Last RESET due to Unknown
print_rst_status: RESET reason: 0x00000000
DYING GASP IRQ Initialized and Enabled
SES: LED GPIO 0x8001 is enabled
map_hw_timer_interrupt,130: interrupt_id 22
map_hw_timer_interrupt,130: interrupt_id 23
map_hw_timer_interrupt,130: interrupt_id 24
map_hw_timer_interrupt,130: interrupt_id 25
Allocated EXT_TIMER number 3
Broadcom Timer Initialized
Registering button 0 (c0822ccc) (bpGpio: 00008004, bpExtIrq:00002000 (2000))
    extIrqIdx:0, gpioNum:4 ACTIVE LOW
  Button 0: Registering press hook btnHook_Ses after 0 ms
Registering button 1 (c0822d40) (bpGpio: 00008009, bpExtIrq:00002001 (2001))
    extIrqIdx:1, gpioNum:9 ACTIVE LOW
  Button 1: Registering press hook btnHook_Print after 0 ms
  Button 1: Registering release hook btnHook_Reset after 0 ms
  Button 1: Registering hold hook btnHook_RestoreToDefault after 5000 ms
(NULL device *): Led 1 renamed to 1_1 due to name collisionBPM: tot_mem_size=268435456B (256MB), buf_mem_size <15%> =40265310B (38MB), num of buffers=15345, buf size=2624
Broadcom BPM Module Char Driver v0.1 Registered<304>
[NTC bpm] bpm_module_init: tot_mem_pool=640 mem_idx:640
init procfs
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
Initializing XFRM netlink socket
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
ip6_gre: GRE over IPv6 tunneling driver
fullmesh registered
NET: Registered protocol family 17
NET: Registered protocol family 15
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
arp_probe_proc_init,1514
Ebtables v2.0 registered
ebt_time registered
ebt_blog registered
ebt_ftos registered
ebt_wmm_mark registered
ebt_qos_map registered
ebt_qos_map registered
L2TP core: blog_l2tp_rcv_check
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Registering SWP/SWPB emulation handler
ubi0: attaching mtd0
ubi0: scanning is finished
ubi0: attached mtd0 (name "rootfs", size 47 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 376, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 350864358
ubi0: available PEBs: 0, total reserved PEBs: 376, PEBs reserved for bad PEB handling: 8
ubi0: background thread "ubi_bgt0d" started, PID 374
block ubiblock0_0: created from ubi0:0(rootfs_ubifs)
squashfs: SQUASHFS error: Xattrs in filesystem, these will be ignored
squashfs: SQUASHFS error: unable to read xattr id index table
VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
devtmpfs: mounted
Freeing unused kernel memory: 208K
init started: BusyBox v1.30.1 (2020-10-21 15:25:50 CST)
starting pid 450, tty '': '/bin/sh -l -c "bcm_boot_launcher start"'
Mounting filesystems...
>>>>> Starting mdev <<<<<
>>>>> Creating static device nodes <<<<<
>>>>> Mounting /data partition <<<<<
ubi1: attaching mtd2
ubi1: scanning is finished
ubi1: attached mtd2 (name "data", size 8 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 96/61, WL threshold: 4096, image sequence number: 1047713076
ubi1: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 4
ubi1: background thread "ubi_bgt1d" started, PID 521
>>>>> Mounting data partition as UBIFS <<<<<
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 592
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "data"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 5840896 bytes (5 MiB, 46 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS (ubi1:0): reserved for root: 275879 bytes (269 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 9988CD43-F094-4E66-9213-5009B8691AE4, small LPT model
get mtd 'plugin' info success
DEVNAME:mtd6
MAJOR:90
MINOR:12
attaching mtd plugin(mtd6)...
ubi2: attaching mtd6
ubi2: scanning is finished
ubi2: attached mtd6 (name "plugin", size 20 MiB)
ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi2: good PEBs: 160, bad PEBs: 0, corrupted PEBs: 0
ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi2: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 305949410
ubi2: available PEBs: 0, total reserved PEBs: 160, PEBs reserved for bad PEB handling: 4
ubi2: background thread "ubi_bgt2d" started, PID 669
UBI device number 2, total 160 LEBs (20316160 bytes, 19.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
attached mtd6 to ubi2
MAJOR:250
MINOR:0
Volume ID:   0 (on ubi2)
Type:        dynamic
Alignment:   1
Size:        152 LEBs (19300352 bytes, 18.UBIFS: parse sync
4 MiB)
State:       OK
Name:  UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 724
      plugin
Character device major/minor: 250:1
mounting ubi volume 'plugin' to /plugin...
UBIFS (ubi2:0): recovery needed
Error:Can't get br0 dev!
UBIFS (ubi2:0): recovery completed
UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "plugin"
UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi2:0): FS size: 18030592 bytes (17 MiB, 142 LEBs), journal size 1015809 bytes (0 MiB, 7 LEBs)
UBIFS (ubi2:0): reserved for root: 851628 bytes (831 KiB)
UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 63A8969F-2848-47BE-9C4A-1D10AFC8BC37, small LPT model
Configuring system...
wlcsm: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Initializing WLCSM Module
WLCSM Module loaded successfully
femid=s755337
*** Using Board NVRAM file from image /etc/wlan/nvram/96755B032_s755337.nvm ***
restore done!
*** populated ***
Loading drivers and kernel modules...

BCMLIBS loaded...
Broadcom 802.1Q VLAN Interface, v0.1
brcmchipinfo: brcm_chipinfo_init entry
Broadcom Ingress QoS Module  Char Driver v1.0 Registered<303>

Broadcom Ingress QoS v1.0 initialized
Broadcom Packet Flow Cache
FCACHE_CONFIG_MAX_FLOW_ENTRIES<16384>
FCACHE_CONFIG_MAX_FDB_ENTRIES<1024>
FCACHE_CONFIG_MAX_HOST_DEV_ENTRIES<64>
FCACHE_CONFIG_MAX_HOST_MAC_ENTRIES<32>
npe_max_entries<32768>
Bind blog_notify_evt_enqueue_fn[<bf08af9c>]
fc_evt task created successfully
max_ent = 16384 intvl_msec = 10000 num_slices = 2000 num_ent = 9 period_msec = 5
NBUFF v1.0 Initialized
Total # of labels = 68
Initialized fcache state
        Pkt HW acceleration is disabled/unavailable.
Broadcom Packet Flow Cache  Char Driver v4.0 Registered<302>
fc_timer_task created successfully
        Pkt HW acceleration is disabled/unavailable.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
[FHW]  pktDbgLvl[0xbf0a1f84]=0
[FHW]  fhw_construct:
Initialized Fcache HW accelerator layer state
flwStatsThread created. numFlwsPerPoll 16383 maxFlwIdx 16383
Fcache Pathstats created
Constructed Broadcom Packet Flow Cache v4.0
Broadcom Command List Driver v1.0
Broadcom Archer Packet Accelerator Intializing
Open archer Netdevice
Archer DS DPI Initialized
Archer US DPI Initialized
Archer WLAN Interface Construct (Threshold 32 packets, Timeout 500 usec, Jiffies 10)
Sysport 0 WOL IRQ 53
Sysport 1 WOL IRQ 59
Archer WLAN Rx Thread Initialized
SYSPORT Driver Constructed (Budget: 128, Coalescing: 826828 nsec)
Archer Mode set to L2+L3
Archer Mode set to L2+L3
Initialized Archer Host Layer
Flow Table (256, 64): d15e5000, 4194304 bytes
Flow Info Table (44, 65536): d19e6000, 2883584 bytes
Command List Table (128): virt 0xc9c00000, phys 0x09c00000, size 2097152 bytes
Command List Control Table (8): cfae0000, 131072 bytes
Sysport Classifier Initialized: Maximum 16384 flows
Archer IQ status changed from 0 to 1
[NTC bitpool] idx_pool_init: 551:FHW[0]:Create Index Pool_Size = 16384
Retrieve num_fhw_path=64
Pathstats allocated 2048 bytes
Broadcom Packet Flow Cache HW acceleration enabled.
Enabled Archer binding to Flow Cache
Broadcom Archer Network Processor Char Driver v0.1 Registered <339>
Archer TCP Pure ACK Enabled
crossbar Mux: connect cb_idx:0  int_ep 0 to ext_ep 2
crossbar Mux: connect cb_idx:0  int_ep 1 to ext_ep -1
Keep normal igp
Keep normal igp
SYSPORT Host Binding Successfull
eth0: Down <8C:0E:60:02:73:00> <IntSw P0, Logical 00> PHY_ID <0x0007f008:0x08: On-chip 1G GPHY> Cfg: ANG.1G; Down
eth1: Down <8C:0E:60:02:73:00> <IntSw P1, Logical 01> PHY_ID <0x02600e01:0x01: On-chip RGMII Auto MAC2MAC> Cfg: FIX.Auto; Down
logical_port 0, intf_index 0, phys_port 0 -> port_index 0, 8 queues
logical_port 1, intf_index 1, phys_port 0 -> port_index 0, 8 queues
SYSPORT[0] = SWITCH_NONE
SYSPORT[1] = SWITCH_NONE
System Port Software TM Initialized
RXQ[0]: IRQ 48, CPU 3
CSB Initialized: 0xc9f63000 (0xc9f63000), size 64 (128)
Ports 1, TDMA Rings 8
Archer DMA Layer Initialized
Sysport Recycle Task: IRQ 49, CPU 3
System Port Software TM Initialized
RXQ[0]: IRQ 54, CPU 3
CSB Initialized: 0xc9f4f000 (0xc9f4f000), size 64 (128)
Ports 1, TDMA Rings 8
Archer DMA Layer Initialized
Sysport Recycle Task: IRQ 55, CPU 3
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
bcm_enet_init:L2451 ENET system contructed and configured enet-kthrd thread
enet_kthread_handler:L335 Instantiating ENET thread
PCIe HCD (impl1)
  bcm963xx-pcie: found core [1] vcore [0]
  bcm963xx-pcie: [0] DT node available: /pcie@85000000
  bcm963xx-pcie: vcore [0] initialized with [2] devices
pcie-vcore 85000000.pcie: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x85000000-0x85ffffff]
pci_bus 0000:01: root bus resource [mem 0x86000000-0x86ffffff]
pci 0000:01:00.0: [14e4:f6ca] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x85000000-0x85ffffff 64bit]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:01.0: [14e4:f6ca] type 00 class 0x028000
pci 0000:01:01.0: reg 0x10: [mem 0x86000000-0x86ffffff 64bit]
pci 0000:01:01.0: supports D1 D2
PCI: bus1: Fast back to back transfers disabled
pci 0000:01:00.0: BAR 0: assigned [mem 0x85000000-0x85ffffff 64bit]
pci 0000:01:01.0: BAR 0: assigned [mem 0x86000000-0x86ffffff 64bit]
  bcm963xx-pcie: [0] DT node available: /pcie@80040000
  bcm963xx-pcie: found port [0] GEN2 Core Rev [3.23] with 2 Lanes
getrcal for res select 5, int 660, ext 620, ratio 120 ratio1 160, rcal 10
  bcm963xx-pcie: Core [0] setting resistor calibration value to 0xa
  bcm963xx-pcie: core [0] link is DOWN
  bcm963xx-pcie: core [0] powered down
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ehci-pci: EHCI PCI platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform: OHCI generic platform driver
ohci-pci: OHCI PCI platform driver
Error:Can't get br0 dev!
++++ Powering up USB blocks
ehci-platform ehci-platform.0: EHCI Host Controller
ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform.0: irq 46, io mem 0x8000c300
ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci-platform ohci-platform.0: Generic Platform OHCI controller
ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
ohci-platform ohci-platform.0: irq 45, io mem 0x8000c400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-platform ehci-platform.1: EHCI Host Controller
ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 3
ehci-platform ehci-platform.1: irq 46, io mem 0x8000c500
ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ohci-platform ohci-platform.1: Generic Platform OHCI controller
ohci-platform ohci-platform.1: new USB bus registered, assigned bus number 4
ohci-platform ohci-platform.1: irq 45, io mem 0x8000c600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver uas
broadcomThermalDrv brcm-therm: init (CPU count 4 4 4 4)
brcm_otp_init entry
realtek_switch----build at 15:19:45, on Oct 21 2020
set high level
set low level
Error:Can't get br0 dev!
set high level
set low level
Error:Can't get br0 dev!
set high level
MDIO Error: MDIO got failure status on phy 0
Error:get invalid svlan for port4
success to initialize realtek switch!
switch port negotiation setting
ethernet@wirespeed is enabled
no modules list in nvram, using defaults...
loading WLAN kernel modules ... firmware_class cfg80211 hnd emf igs dhd wl
cfg80211: Calling CRDA to update world regulatory domain
Error:Can't get br0 dev!
Loading HND Module
igs_module_init:867:     IGS 29 create network socket successful
dhd_module_init in
DHD_FKB_POOL size is:1280 and entry size:2624
DHD_PKTTAG POOL size is:2592 and entry size:64
dhd_pktfwd_sys_init:  dhd_PKTFWD[1.0.0] Success
dhd_queue_budget = 256
dhd_sta_threshold = 2048
dhd_if_threshold = 65536
no wifi platform data, skip
dhdpcie_pci_probe: chipmatch failed!! Unsupported vendor 14e4 device f6ca
dhdpcie_pci_probe: chipmatch failed!! Unsupported vendor 14e4 device f6ca
No Broadcom PCI device enumerated!
dhd_module_init out
wl_module_init: passivemode set to 0x1
wl_module_init: txworkq set to 0x0
wl_pktfwd_sys_init:  WL_PKTFWD[1.1.0] Success
wl 0000:01:00.0: enabling device (0140 -> 0142)
wl0: creating kthread wl0-kthrd
si_doattach: using BAR0 value: enum_base=85000000
BME Service Initialization
BME: M2M Core id 0x844 rev 128
wl0: phy_radio_attach: RF Band Cap: 2G:1 5G:1
kerSysGetWifiLed(0) returned 0
BME:register key<1010804> user RLM sel IDX set 1 mem 4 8 hi 0 0
wl0 taf_do_enable: TAF is enabled
wl0_awl attach successful tx: 1, rx: 2
WL_FLCTL[0] bpm_total_skb 12276, exhaustion_hi 1227, exhaustion_lo 3069, prio_favor 4
Archer WLAN Bind: wl%d, wl_radio_idx 0, radio_index 0, mode SKB
wl_wfd_bind: wl0 wfd_idx 0 success
wl0: Broadcom BCM63178 802.11 Wireless Controller 17.10.121.2004 (r786578)
wl 0000:01:01.0: enabling device (0140 -> 0142)
wl1: creating kthread wl1-kthrd
si_doattach: using BAR0 value: enum_base=86000000
BME Service Initialization
BME: M2M Core id 0x844 rev 128
wl1: phy_radio_attach: RF Band Cap: 2G:1 5G:1
kerSysGetWifiLed(1) returned 0
BME:register key<1010804> user RLM sel IDX set 1 mem 4 8 hi 0 0
wl1 taf_do_enable: TAF is enabled
wl1_awl attach successful tx: 1, rx: 2
WL_FLCTL[1] bpm_total_skb 12276, exhaustion_hi 1227, exhaustion_lo 3069, prio_favor 4
Archer WLAN Bind: wl%d, wl_radio_idx 1, radio_index 1, mode SKB
wl_wfd_bind: wl1 wfd_idx 1 success
wl1: Broadcom BCM63178 802.11 Wireless Controller 17.10.121.2004 (r786578)
Configuring wlan related threads...
Error:Can't get br0 dev!
no thread pin applied
Wlan related processes are pinned by default
set bcm_archer_us 842 to aff:8
set wl0-kthrd 1232 to aff:1
set wl1-kthrd 1249 to aff:2
set wl0-kthrd and pid:1232 to prio:5
set wl1-kthrd and pid:1249 to prio:5
Starting HouseKeeping task...
Loading GRE kernel modules...
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
PPTP driver version 0.8.5
Configuring networking...
Enabling IPv6 Forwarding...
OpenSSL 1.1.1b  26 Feb 2019
writing RSA key
random: dropbearconvert urandom read with 4 bits of entropy available
Starting UBUS daemon...
Saving kernel bootup messages for dumpsysinfo...
Starting CMS smd...

cfg80211: Calling CRDA to update world regulatory domain
===== Release Version 5.02L.07p1 (build timestamp 201021_1506) =====

/bin/smd:13.847:error:symbol_to_value:350:Could not find symbol EID_ROUTERCAPABILITY in eid_symbol_table
/bin/smd:13.847:error:is_eInfo_valid:409:eInfo must have a non-zero EID
Initializing CMS MDM in Pure181 mode
[error] devCtl_getNvramParamValue UserWd ret=9003
[error] devCtl_getNvramParamValue ctei ret=9003
Archer Mode set to L3
Broadcom Packet Flow Cache acceleration mode <L3>
SHM_SYNC_LOG_FILE is /var/log/log.txt
DDR Self Refresh is enabled
ssk:14.203:error:rutSntp_restart_dev2:109:TZ:-06:00 timezone:Central America
eth1: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
eth1 (Int switch port: 1) (Logical Port: 1) (phyId: 1) Link Up at 1000 mbps full duplex
eth1: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
ioctl command return error!
ioctl command return error!
ssk:14.286:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.293:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.300:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.307:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.313:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.320:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.326:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.333:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

Broadcom SNTP Stack v0.1 (Oct 21 2020, 15:26:32)
ioctl command return error!
ssk:14.346:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.353:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.360:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.366:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.373:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.380:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.386:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.393:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

sched: RT throttling activated
ioctl command return error!
ssk:14.410:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.417:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.423:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.430:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.437:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.444:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.451:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.457:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

netdev path : eth1.0 -> eth1
BCMVLAN : eth1 mode was set to RG
eth1: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
ioctl command return error!
ssk:14.520:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.527:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.533:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.540:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.547:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.553:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.560:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

ssk:14.567:error:rutQos_tmQueueConfig:1697:unconfig set rate 0

[ERROR vlan] registerVlanDeviceByName,415: Failed to REGISTER VLAN Device eth1.0
[ERROR vlan] vlanIoctl ,618: Failed to create VLAN device (eth1, 0)
[ERROR vlanctl] vlanCtBCMVLAN : eth1 mode was set to RG
l_createVlanInterface, 268: No s[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
uch device
[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=0, dir=0)
[ERROR vlanctl] vlanCt[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
l_insertTagRule, 470: Invalid ar[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=1, dir=0)
gument
[ERROR[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
 vlanctl] vlanCtl_insertTagRule,[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=2, dir=0)
 470: Invalid argument
[ERROR vlanctl] vlanCtl_insertTagRule, 470: Invalid argument
eth1: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
[ERROR vlan] registerVlanDeviceByName,415: Failed to REGISTER VLAN Device eth1.0
[ERROR vlan] vlanIoctl ,618: Failed to create VLAN device (eth1, 0)
[ERROR vlanctl] vlanCtBCMVLAN : eth1 mode was set to RG
l_createVlanInterface, 268: No s[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
uch device
[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=0, dir=0)
[ERROR vlanctl] vlanCt[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
l_insertTagRule, 470: Invalid arError:Can't get br0 dev!
gument
[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=1, dir=0)
[ERROR vlanctl] vlanCt[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
l_insertTagRule, 470: Invalid ar[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=2, dir=0)
gument
[ERROR vlanctl] vlanCtl_insertTagRule, 470: Invalid argument
eth1: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
[ERROR vlan] registerVlanDeviceByName,415: Failed to REGISTER VLAN Device eth1.0
[ERROR vlan] vlanIoctl ,618: Failed to create VLAN device (eth1, 0)
[ERROR vlanctl] vlanCtBCMVLAN : eth1 mode was set to RG
l_createVlanInterface, 268: No s[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
uch device
[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=0, dir=0)
[ERROR vlanctl] vlanCt[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
l_insertTagRule, 470: Invalid ar[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=1, dir=0)
gument
[ERROR[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
 vlanctl] vlanCtl_insertTagRule,[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=2, dir=0)
 470: Invalid argument
[ERROR vlanctl] vlanCtl_insertTagRule,IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
 470: Invalid argument
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
eth1: sysport_tm port shaper set to 999000 kbps (phy speed 1000000 kbps)
[ERROR vlan] registerVlanDeviceByName,415: Failed to REGISTER VLAN Device eth1.0
[ERROR vlan] vlanIoctl ,618: Failed to create VLAN device (eth1, 0)
[ERROR vlanctl] vlanCtBCMVLAN : eth1 mode was set to RG
l_createVlanInterface, 268: No s[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
uch device
[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=0, dir=0)
[ERROR vlanctl] vlanCt[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
l_insertTagRule, 470: Invalid ar[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=1, dir=0)
gument
[ERROR[ERROR vlan] bcmVlan_insertTagRule,2471: The last rule table entry has already been occupied
 vlanctl] vlanCtl_insertTagRule,[ERROR vlan] vlanIoctl ,771: Failed to Insert Tag Rule in eth1 (tags=2, dir=0)
 470: Invalid argument
[ERROR vlanctl] vlanCtl_insertTagRule, 470: Invalid argument
IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
Netfilter messages via NETLINK v0.30.
ssk:15.623:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
hostspro:15.731:error:symbol_to_value:350:Could not find symbol EID_ROUTERCAPABILITY in eid_symbol_table
hostspro:15.732:error:is_eInfo_valid:409:eInfo must have a non-zero EID
ssk:15.781:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ip_tables: (C) 2000-2006 Netfilter Core Team
ip6_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (3912 buckets, 15648 max)
xt_connbytes: Forcing CT accounting to be enabled
ctnetlink v0.93: registering with nfnetlink.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: Chain already exists.
ssk:16.385:error:rut_speedlimit_tc_init:1792:ifname1:eth1
ssk:16.385:error:rut_speedlimit_tc_init:1792:ifname2:eth1
ssk:16.386:error:rut_speedlimit_tc_init:1792:ifname3:eth1
ssk:16.386:error:rut_speedlimit_tc_init:1792:ifname4:eth1
ssk:16.386:error:rut_speedlimit_tc_init:1792:ifname5:eth1
cfg80211: Calling CRDA to update world regulatory domain
iptables: Chain already exists.
iptables: Chain already exists.
iptables: Chain already exists.
ip6tables: Chain already exists.
ip6tables: Chain already exists.
iptables: Chain already exists.
ssk:17.128:error:rut_updateDevRateLimit:2146:rut_updateDevRateLimit Enter
ssk:17.133:error:rut_updateDevRamonitor task is initialized pid= 1638
teLimit:2209:rut_updateDevRateLimit Leave
vlanctl --if-create-name eth1 eth1.1
hostspro:17.152:error:initBaseMac:324:g_baseMac:[8c:0e:60:02:73:00],base_Tmp:[0e:60:02:73]

netdev path : eth1.1 -> eth1
vlanctl --if eth1 --rx --tags 1 --filter-vid 11 0 --pop-tag --set-rxif eth1.1 --rule-append
vlanctl --if eth1 --rx --tags 2 --filter-vid 11 0 --pop-tag --set-rxif eth1.1 --rule-append
vlanctl --if eth1 --tx --tags 0 --filter-txif eth1.1 --push-tag --set-vid 11 0 --set-pbits 0 0 --rule-append
ifconfig eth1.1 up
brctl addif br0 eth1.1
disable port eth1.1
device eth1.1 entered promiscuous mode
device eth1 entered promiscuous mode
disable port eth1.1
br0: port 1(eth1.1) entered listening state
br0: port 1(eth1.1) entered listening state
vlanctl --if-create-name eth1 eth1.2
Broadcom Packet Flow Cache learning via BLOG enabled.
netdev path : eth1.2 -> eth1
vlanctl --if eth1 --rx --tags 1 --filter-vid 12 0 --pop-tag --set-rxif eth1.2 --rule-append
vlanctl --if eth1 --rx --tags 2 --filter-vid 12 0 --pop-tag --set-rxif eth1.2 --rule-append
vlanctl --if eth1 --tx --tags 0 --filter-txif eth1.2 --push-tag --set-vid 12 0 --set-pbits 0 0 --rule-append
ifconfig eth1.2 up
brctl addif br0 eth1.2
killall: crond: no process killed
disable port eth1.2
device eth1.2 entered promiscuous mode
disable port eth1.2
br0: port 2(eth1.2) entered listening state
br0: port 2(eth1.2) entered listening state
vlanctl --if-create-name eth1 eth1.3
netdev path : eth1.3 -> eth1
vlanctl --if eth1 --rx --tags 1 --filter-vid 13 0 --pop-tag --set-rxif eth1.3 --rule-append
vlanctl --if eth1 --rx --tags 2 --filter-vid 13 0 --pop-tag --set-rxif eth1.3 --rule-append
vlanctl --if eth1 --tx --tags 0 --filter-txif eth1.3 --push-tag --set-vid 13 0 --set-pbits 0 0 --rule-append
ifconfig eth1.3 up
brctl addif br0 eth1.3
disable port eth1.3
device eth1.3 entered promiscuous mode
disable port eth1.3
br0: port 3(eth1.3) entered listening state
br0: port 3(eth1.3) entered listening state
vlanctl --if-create-name eth1 eth1.4
netdev path : eth1.4 -> eth1
vlanctl --if eth1 --rx --tags 1 --filter-vid 14 0 --pop-tag --set-rxif eth1.4 --rule-append
vlanctl --if eth1 --rx --tags 2 --filter-vid 14 0 --pop-tag --set-rxif eth1.4 --rule-append
vlanctl --if eth1 --tx --tags 0 --filter-txif eth1.4 --push-tag --set-vid 14 0 --set-pbits 0 0 --rule-append
ifconfig eth1.4 up
brctdisable port eth1.4
l addif br0 eth1.4
device eth1.4 entered promiscuous mode
disable port eth1.4
br0: port 4(eth1.4) entered listening state
br0: port 4(eth1.4) entered listening state
fc config --mcast 0
Broadcom Packet Flow Cache acceleration of multicast flows IPv4<DISABLED> IPv6<DISABLED>
fc config --mcast-learn 1
Broadcom Packet Flow Cache Learning of multicast flows <ENABLED>
ssk:17.565:error:main:213:speedlimit init
ssk:18.402:error:rutBridge_configVlanRules_dev2:1410:Enter: portName=eth1.1 l2Ifdevice eth1.1 left promiscuous mode
name=eth1 tpid=0x8100 priorityTagging=0 pbits=0 untagged=1 vlanId=-1
br0: port 1(eth1.1) entered disabled state
disable port eth1.1
device eth1.1 entered promiscuous mode
disable port eth1.1
br0: port 1(eth1.1) entered listening state
br0: port 1(eth1.1) entered listening state
ssk:18.497:error:checkEthLinkStatusLocked_dev2:515:link change detected on eth1 (upstream=0) status=Up MsgType=268436054
ssk:18.606:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
iptables: Chain already exists.
iptables: Chain already exists.
iptables: Chain already exists.
ip6tables: Chain already exists.
ip6tables: Chain already exists.
iptables: Chain already exists.
ssk:18.820:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ssk:18.925:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
Broadcom Packet Flow Cache flushing the flows

cdes · May 29, 2022, 7:46pm

part III:

ssk:19.064:error:rutNtwk_selectActiveIpvxDnsServers:401:Fail to get dns ip from br0.
ssk:19.171:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ssk:19.276:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ssk:19.382:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
Broadcom Packet Flow Cache flushing the flows

ssk:19.389:errobr0: port 2(eth1.2) entered learning state
r:qdmIpv6_fullPathToPefixLocked_dev2:70:invalid argument. mdmPath=0x0 prefix=0xbea0f438
ssk:19.389:error:rutIp_configureStaticIpv6Addrs:100:cannot get prefix from (null)
br0: port 3(eth1.3) entered learning state
br0: port 4(eth1.4) entered learning state
ssk:19.564:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
backup_psi_number_blk=1 result=49152
cfg80211: Calling CRDA to update world regulatory domain
ssk:20.269:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ssk:20.375:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
br0: port 1(eth1.1) entered learning state
ssk:20.475:error:rutBridge_configVlanRules_dev2:1410:Enter: portName=eth1.2 l2Ifdevice eth1.2 left promiscuous mode
name=eth1 tpid=0x8100 priorityTagging=0 pbits=0 untagged=1 vlanId=-1
br0: port 2(eth1.2) entered disabled state
disable port eth1.2
device eth1.2 entered promiscuous mode
disable port eth1.2
br0: port 2(eth1.2) entered listening state
br0: port 2(eth1.2) entered listening state
ssk:20.666:error:rutBridge_configVlanRules_dev2:1410:Enter: portName=eth1.3 l2Ifdevice eth1.3 left promiscuous mode
name=eth1 tpid=0x8100 priorityTagging=0 pbits=0 untagged=1 vlanId=-1
br0: port 3(eth1.3) entered disabled state
disable port eth1.3
device eth1.3 entered promiscuous mode
disable port eth1.3
br0: port 3(eth1.3) entered listening state
br0: port 3(eth1.3) entered listening state
ssk:20.857:error:rutBridge_configVlanRules_dev2:1410:Enter: portName=eth1.4 l2Ifdevice eth1.4 left promiscuous mode
name=eth1 tpid=0x8100 priorityTagging=0 pbits=0 untagged=1 vlanId=-1
br0: port 4(eth1.4) entered disabled state
disable port eth1.4
device eth1.4 entered promiscuous mode
disable port eth1.4
br0: port 4(eth1.4) entered listening state
br0: port 4(eth1.4) entered listening state
ssk:21.313:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ssk:21.420:error:rutNtwk_LanInterfaceRule:1659:enable is 0,del all rule
ssk:21.527:error:ssk_main:812:cannot handle msg type 0x20000048 from 5003 (flags=0x14)
ssk:21.528:error:ssk_main:812:cannot handle msg type 0x20000048 from 5003 (flags=0x10014)
ssk:21.532:error:ssk_main:812:cannot handle msg type 0x20000048 from 5003 (flags=0x10014)
ssk:21.534:error:ssk_main:812:cannot handle msg type 0x20000048 from 5003 (flags=0x10014)
hostspro:21.607:error:processMessageFromSmd:211:unrecognized msg src:[20],dst:[5004], type:[0x10000250]
starting pid 2613, tty '': '-/bin/sh -l -c consoled'
autoUpgrade start now
autoUpgrade:21.640:error:symbol_to_value:350:Could not find symbol EID_ROUTERCAPABILITY in eid_symbol_table
autoUpgrade:21.641:error:is_eInfo_valid:409:eInfo must have a non-zero EID
autoUpgrade:21.671:error:autoUpgrade_init:254:policy file url: http://www.juplink-me262.ltd/downloads/US/policy.conf
autoUpgrade:21.671:error:autoUpgrade_processMessageFromSmd:192:unrecognized msg src:[20],dst:[5015], type:[0x10000250]
autoUpgrade:21.671:error:autoUpgrade_processMessageFromSmd:192:unrecognized msg src:[5015],dst:[5015], type:[0x100007c0]
BCM96755 Broadband Router
cloud_main.c][main][733]: argv[0]=cloud
cloud_main.c][main][733]: argv[0]=cloud-mon
cloud_main.c][main][733]: argv[0]=cloud
cloud-mon:21.977:error:symbol_to_value:350:Could not find symbol EID_ROUTERCAPABILITY in eid_symbol_table
cloud:21.977:error:symbol_to_value:350:Could not find symbol EID_ROUTERCAPABILITY in eid_symbol_table
cloud:21.977:error:symbol_to_value:350:Could not find symbol EID_ROUTERCAPABILITY in eid_symbol_table
cloud:21.977:error:is_eInfo_valid:409:eInfo must have a non-zero EID
cloud:21.977:error:is_eInfo_valid:409:eInfo must have a non-zero EID
cloud-mon:21.977:error:is_eInfo_valid:409:eInfo must have a non-zero EID
cloud-mon:21.996:error:rut_getL3InfoByUpstreamTrue:3443:qdmRt_getGatewayIpv4AddrByFullPathLocked_dev2 ret 9804 , ipIntfFullPathNoEndDot:[Device.IP.Interface.1]
cloud:21.996:error:rut_getL3InfoByUpstreamTrue:3443:qdmRt_getGatewayIpv4AddrByFullPathLocked_dev2 ret 9804 , ipIntfFullPathNoEndDot:[Device.IP.Interface.1]
cloud:21.996:error:rut_getL3InfoByUpstreamTrue:3443:qdmRt_getGatewayIpv4AddrByFullPathLocked_dev2 ret 9804 , ipIntfFullPathNoEndDot:[Device.IP.Interface.1]
send igmp query due to eth1.1 stp state forwarding.
br0: topology change detected, propagating
br0: port 1(eth1.1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
br0: port 2(eth1.2) entered learning state
br0: port 3(eth1.3) entered learning state
Configuring wlan related threads...
br0: port 4(eth1.4) entered learning state
no thread pin applied
Wlan related processes are pinned by default
set bcm_archer_us 842 to aff:8
set wl0-kthrd 1232 to aff:1
cfg80211: Calling CRDA to update world regulatory domain
set wl1-kthrd 1249 to aff:2
set wl0-kthrd and pid:1232 to prio:5
set wl1-kthrd and pid:1249 to prio:5
backup_psi_number_blk=1 result=49152
killall: wps_pbcd: no process killed
killall: hostapd: no process killed
killall: wpa_supplicant: no process killed
send igmp query due to eth1.2 stp state forwarding.
br0: topology change detected, propagating
br0: port 2(eth1.2) entered forwarding state
wl0: cmd=231: Invalid argument
wl0: WLC_SET_VAR(wet_enab): Operation not supported
wl0: WLC_SET_VAR(bsscfg:map_8021q_settings): Operation not supported
wl0: WLC_SET_VAR(psta): Operation not supported
wl0: WLC_SET_VAR(bsscfg:aspm): Operation not supported
wl0: cmd=243: Invalid argument
send igmp query due to eth1.3 stp state forwarding.
br0: topology change detected, propagating
br0: port 3(eth1.3) entered forwarding state
wl0: WLC_SET_VAR(wme_tx_params): Operation not supported
wl0: WLC_SET_VAR(btc_mode): Operation not supported
wl0: WLC_SET_VAR(rtsthresh): Invalid argument
wl0: WLC_SET_VAR(bcn_rotate): Operation not supported
wl0: cmd=2: Invalid argument
send igmp query due to eth1.4 stp state forwarding.
br0: topology change detected, propagating
br0: port 4(eth1.4) entered forwarding state
wl0: WLC_SET_VAR(roam_off): Invalid argument
wl0: WLC_SET_VAR(bcnprs_txpwr_offset): Invalid argument
wl1: cmd=231: Invalid argument
wl1: WLC_SET_VAR(wet_enab): Operation not supported
wl1: WLC_SET_VAR(bsscfg:map_8021q_settings): Operation not supported
wl1: WLC_SET_VAR(psta): Operation not supported
wl1: WLC_SET_VAR(bsscfg:aspm): Operation not supported
wl1: WLC_SET_VAR(wme_tx_params): Operation not supported
wl1: WLC_SET_VAR(btc_mode): Operation not supported
wl1: WLC_SET_VAR(rtsthresh): Invalid argument
wl1: WLC_SET_VAR(bcn_rotate): Operation not supported
wl1: WLC_SET_VAR(traffic_thresh): Invalid argument
wl1: WLC_SET_VAR(traffic_thresh): Invalid argument
wl1: WLC_SET_VAR(traffic_thresh): Invalid argument
wl1: WLC_SET_VAR(traffic_thresh): Invalid argument
wl1: WLC_SET_VAR(traffic_thresh): Invalid argument
wl1: WLC_SET_VAR(roam_off): Invalid argument
wl1: WLC_SET_VAR(bcnprs_txpwr_offset): Invalid argument
Broadcom Packet Flow Cache flushing the flows

(ssk) Wifi Lan wl1 link up
disable port wl1
device wl1 entered promiscuous mode
disable port wl1
br0: port 5(wl1) entered listening state
br0: port 5(wl1) entered listening state
cfg80211: Calling CRDA to update world regulatory domain
cevent_bitvec [0 1 2 3 4 5 6 7 8 9 10 11 12 16 17 23 25 40 46 136 180]
cevent_bitvec [0 1 2 3 4 5 6 7 8 9 10 11 12 16 17 23 25 40 46 136 180]
eapd_brcm_open: Sock buffer size  SO_RCVBUF=425984  SO_SNDBUF=425984
eapd_brcm_open: Sock buffer size  SO_RCVBUF=425984  SO_SNDBUF=425984
dm directory may not exist (No such file or directory). Creating it
Broadcom Traffic Ordering Agent -- starting on wl0 as daemon process...
acsd: wl1: Selecting 5g band ACS policy
Archer TCP Pure ACK Disabled
Broadcom Packet Flow Cache TCP ACK Multi-Flow <Disabled>
br0: port 5(wl1) entered learning state
acsd: wl1: selected channel spec: 0xe09b
acsd: wl1: Adjusted channel spec: 0xe09b
acsd: wl1: selected channel spec: 0xe09b
sh: acs_cli: not found
sh: acs_cli: not found
Err: rc: 3515: radio 0 disabled
radio_iflist[1]: wl1
radio_iflist[2]:
radio_iflist[1]: wl1
filtered_iflist: wl1
primary_iflist: wl1
virtual_iflist:
primary_iflist: wl1
wl1
cfg80211: Calling CRDA to update world regulatory domain
enable_trace_dbg:1
Configuration file: /tmp/wl1_hapd.conf
rfkill: Cannot open RFKILL control device
wl1: interface state UNINITIALIZED->COUNTRY_UPDATE
CEVENTD[3638]: 1558315479162 wl1      00:02:00:18:00:00    24 0000 0000 0000 Driver   --  E_RADIO/40
CEVENTD[3638]: 1558315479194 wl1      8C:0E:60:02:73:02     1 0000 0000 0000 Driver   --  E_LINK/16
send igmp query due to wl1 stp state forwarding.
br0: topology change detected, propagating
br0: port 5(wl1) entered forwarding state
Info: wps_pbcd wps_pbcd_fill_info_objects_list get radio unit failed for eth1.1
Info: wps_pbcd wps_pbcd_fill_info_objects_list get radio unit failed for eth1.2
Info: wps_pbcd wps_pbcd_fill_info_objects_list get radio unit failed for eth1.3
Info: wps_pbcd wps_pbcd_fill_info_objects_list get radio unit failed for eth1.4
Info: wps_pbcd wps_pbcd_fill_info_objects_list get radio unit failed for eth0.1
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:cmsPhl_setParameterValues:635:param Device.WiFi.SSID.{i}.MACAddress is NOT writable
WLCTDM:32.011:error:apply_scache:168:failed to apply scache table! cret=9003
WLCTDM:32.011:error:conv_save:184:Failed to apply all changes to MDM!
WBD(multiap_mode) is not enabled: 0=0
BSD is not enabled: 0=0
Both BSD and WBD is Disabled. flag=0
Shutting down 1905
Shutting down 1905
wl: Not Permitted
--WLSSK RESTART DONE--
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: Calling CRDA to update world regulatory domain
ssk_henggu:40.528:error:processOtherWanChange:625:g_otherWanChangeCnt=11
cfg80211: Calling CRDA to update world regulatory domain
ssk_henggu:42.530:error:processOtherWanChange:625:g_otherWanChangeCnt=3
ssk_henggu:44.533:error:processOtherWanChange:625:g_otherWanChangeCnt=2
cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
ssk_henggu:46.536:error:processOtherWanChange:625:g_otherWanChangeCnt=1
ssk_henggu:46.536:error:processOtherWanChange:630:rut_hg_rtk_swtich_set_other_wan_vlan
echo wan_vid 0 > /proc/rtkswitch/set
fc config --mcast 0
Broadcom Packet Flow Cache acceleration of multicast flows IPv4<DISABLED> IPv6<DISABLED>
fc config --mcast-learn 1
Broadcom Packet Flow Cache Learning of multicast flows <ENABLED>
ssk_henggu:57.388:error:processMeshMonitor:2149:mesh is disabled! exit monitor
ssk_henggu:62.364:error:processRepeaterMonitor:1663:repeater is disabled! exit monitor
autoUpgrade:81.732:error:autoUpgrade_policy_timer:102:download policy at 00:00:00+delay 1224 sec
autoUpgrade:81.732:error:autoUpgrade_calc_timer_delay:166:create check policy timer, delay 17754s, 2019-05-20 00:21:24
autoUpgrade:175.612:error:autoUpgrade_processMessageFromSmd:157:CMS_MSG_TIME_STATE_CHANGED state:4

flygarn12 · May 29, 2022, 8:15pm

Lesson 1 in development. Learn how to make a forum post with preformatted text.

WereCatf · May 29, 2022, 8:18pm

I gave the log only a very cursory look, but it seems the hardware is all Broadcom. That.... does not bode well.

Borromini · May 30, 2022, 6:07pm

Broadcom SoC, so end of discussion if you'd like OpenWrt support for the wireless.