Issue with Linksys WRT610N V2

Boot Verbose Mode

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Fri Jul 10 15:25:09 CST 2009 (ljh@team2-complier)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.

No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 480MHz
Tot mem: 65536 KBytes

CFE mem:    0x80700000 - 0x8079DA10 (645648)
Data:       0x80732970 - 0x80736FD0 (18016)
BSS:        0x80736FD0 - 0x80737A10 (2624)
Heap:       0x80737A10 - 0x8079BA10 (409600)
Stack:      0x8079BA10 - 0x8079DA10 (8192)
Text:       0x80700000 - 0x8073296C (207212)

Boot version: v4.2
The boot is CFE

mac_init(): Find mac [68:7F:74:1C:E4:0E] in location 0
Nothing...
country_init(): Find country code in location 0
The country is same
Device eth0:  hwaddr 68-7F-74-1C-E4-0E, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Check CRC of image1
  Header CRC:    0x658BAB
  Calculate CRC: 0x658BAB
Image 1 is OK
Try to load image 1.
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3832 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
[    0.000000] Linux version 4.14.156 (builder@buildhost) (gcc version 7.5.0 (Op                                                                                                                                                             enWrt GCC 7.5.0 r10775-db8345d8e4)) #0 Sat Nov 30 15:52:33 2019
[    0.000000] CPU0 revision is: 00019740 (MIPS 74Kc)
[    0.000000] bcm47xx: Using bcma bus
[    0.000000] (NULL device *): bus0: Found chip with id 0x4716, rev 0x01 and pa                                                                                                                                                             ckage 0x0A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32                                                                                                                                                              bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] random: get_random_bytes called from 0x8046b738 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59876K/65536K available (3887K kernel code, 162K rwdata,                                                                                                                                                              464K rodata, 212K init, 279K bss, 5660K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 128
[    0.000000] (NULL device *): bus0: Core 0 found: ChipCommon (manuf 0x4BF, id                                                                                                                                                              0x800, rev 0x1F, class 0x0)
[    0.000000] (NULL device *): bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id                                                                                                                                                              0x812, rev 0x11, class 0x0)
[    0.000000] (NULL device *): bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x                                                                                                                                                             82D, rev 0x00, class 0x0)
[    0.000000] (NULL device *): bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x                                                                                                                                                             82C, rev 0x01, class 0x0)
[    0.000000] (NULL device *): bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, i                                                                                                                                                             d 0x819, rev 0x04, class 0x0)
[    0.000000] (NULL device *): bus0: Core 5 found: PCIe (manuf 0x4BF, id 0x820,                                                                                                                                                              rev 0x0E, class 0x0)
[    0.000000] (NULL device *): bus0: Core 6 found: DDR1/DDR2 Memory Controller                                                                                                                                                              (manuf 0x4BF, id 0x82E, rev 0x01, class 0x0)
[    0.000000] (NULL device *): bus0: Core 7 found: Internal Memory (manuf 0x4BF                                                                                                                                                             , id 0x80E, rev 0x07, class 0x0)
[    0.000000] (NULL device *): bus0: Core 8 found: I2S (manuf 0x4BF, id 0x834,                                                                                                                                                              rev 0x00, class 0x0)
[    0.000000] (NULL device *): bus0: Early bus registered
[    0.000000] MIPS: machine is Linksys WRT610N V2
[    0.000000] bcm47xx: Setting up vectored interrupts
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i                                                                                                                                                             dle_ns: 7963585194 ns
[    0.000017] sched_clock: 32 bits at 240MHz, resolution 4ns, wraps every 89478                                                                                                                                                             48189ns
[    0.000111] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[    0.070041] pid_max: default: 32768 minimum: 301
[    0.070459] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070501] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.074397] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma                                                                                                                                                             x_idle_ns: 19112604462750000 ns
[    0.074453] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.075827] NET: Registered protocol family 16
[    0.106489] clocksource: Switched to clocksource MIPS
[    0.108959] NET: Registered protocol family 2
[    0.110619] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110683] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110723] TCP: Hash tables configured (established 1024 bind 1024)
[    0.110991] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.111048] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.111504] NET: Registered protocol family 1
[    0.166969]  2(S)*
[    0.166977]  3
[    0.166999]  4
[    0.167014]  5
[    0.167029]  6
[    0.167043]  D
[    0.167058]  I
[    0.167072]
[    0.167103]  2(S)
[    0.167111]  3*
[    0.167126]  4
[    0.167140]  5
[    0.167154]  6
[    0.167169]  D
[    0.167183]  I
[    0.167197]
[    0.167228]  2(S)
[    0.167235]  3
[    0.167250]  4*
[    0.167264]  5
[    0.167279]  6
[    0.167293]  D
[    0.167307]  I
[    0.167321]
[    0.167351]  2(S)
[    0.167358]  3
[    0.167373]  4
[    0.167387]  5
[    0.167401]  6
[    0.167416]  D
[    0.167430]  I*
[    0.167444]
[    0.167475]  2(S)
[    0.167482]  3
[    0.167496]  4
[    0.167511]  5*
[    0.167525]  6
[    0.167539]  D
[    0.167553]  I
[    0.167567]
[    0.167598]  2(S)
[    0.167606]  3
[    0.167620]  4
[    0.167634]  5
[    0.167649]  6*
[    0.167663]  D
[    0.167677]  I
[    0.167691]
[    0.167722]  2(S)
[    0.167729]  3
[    0.167744]  4
[    0.167758]  5
[    0.167773]  6
[    0.167787]  D*
[    0.167801]  I
[    0.167815]
[    0.167845]  2(S)
[    0.167852]  3
[    0.167867]  4
[    0.167881]  5
[    0.167895]  6
[    0.167909]  D
[    0.167924]  I*
[    0.167937]
[    0.167968]  2(S)*
[    0.167975]  3
[    0.167990]  4
[    0.168004]  5
[    0.168018]  6
[    0.168033]  D
[    0.168047]  I
[    0.168061]
[    0.168089] (NULL device *): bus0: PCIEcore in host mode found
[    0.371843] PCI host bridge to bus 0000:00
[    0.371901] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0bffffff]
[    0.371930] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
[    0.371959] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.371990] pci_bus 0000:00: No busn resource found for root bus, will use [b                                                                                                                                                             us 00-ff]
[    0.372117] bcma: PCI: Fixing up bridge 0000:00:00.0
[    0.372141] bcma: PCI: Fixing up device 0000:00:00.0
[    0.372296] pci 0000:00:00.0: enabling Extended Tags
[    0.372874] bcma: PCI: Fixing up bridge 0000:00:00.1
[    0.372909] bcma: PCI: Fixing up device 0000:00:00.1
[    0.373062] pci 0000:00:00.1: enabling Extended Tags
[    0.373865] pci 0000:00:01.0: enabling Extended Tags
[    0.373911] bcma: PCI: Fixing up addresses 0000:00:01.0
[    0.373956] pci 0000:00:01.0: BAR 0: assigned [mem 0x08000000-0x08003fff 64bi                                                                                                                                                             t]
[    0.374771] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    0.374805] bcma: PCI: Fixing up device 0000:00:01.0
[    0.426538] ssb: Found chip with id 0x4322, rev 0x01 and package 0x0A
[    0.697578] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[    0.699307] (NULL device *): bus0: Bus registered
[    0.700750] Crashlog allocated RAM at address 0x3f00000
[    0.709426] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.719138] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.719176] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT                                                                                                                                                             Y) (c) 2001-2006 Red Hat, Inc.
[    0.739324] io scheduler noop registered
[    0.739362] io scheduler deadline registered (default)
[    0.739948] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.744163] console [ttyS0] disabled
[    0.764432] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250                                                                                                                                                             000) is a U6_16550A
[    1.441962] console [ttyS0] enabled
[    1.447152] physmap platform flash device: 02000001 at 1c000000
[    1.453275] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufa                                                                                                                                                             cturer ID 0x0000c2 Chip ID 0x0000cb
[    1.463787] Amd/Fujitsu Extended Query Table at 0x0040
[    1.469086]   Amd/Fujitsu Extended Query version 1.1.
[    1.474230] number of CFI chips: 1
[    1.522275] 3 bcm47xxpart partitions found on MTD device physmap-flash.0
[    1.529145] Creating 3 MTD partitions on "physmap-flash.0":
[    1.534829] 0x000000000000-0x000000040000 : "boot"
[    1.545535] 0x000000040000-0x0000007f0000 : "firmware"
[    1.552406] 3 trx partitions found on MTD device firmware
[    1.558012] Creating 3 MTD partitions on "firmware":
[    1.563078] 0x00000000001c-0x000000000944 : "loader"
[    1.572783] 0x000000000944-0x000000178400 : "linux"
[    1.580279] 0x000000178400-0x0000007b0000 : "rootfs"
[    1.586956] mtd: device 4 (rootfs) set to be root filesystem
[    1.592770] 1 squashfs-split partitions found on MTD device rootfs
[    1.599149] 0x000000410000-0x0000007b0000 : "rootfs_data"
[    1.610229] 0x0000007f0000-0x000000800000 : "nvram"
[    1.622131] libphy: Fixed MDIO Bus: probed
[    1.626924] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 sec                                                                                                                                                             onds)
[    1.634794] GPIO_WDT: failed to register misc device
[    1.641980] NET: Registered protocol family 10
[    1.654947] Segment Routing with IPv6
[    1.658968] NET: Registered protocol family 17
[    1.663625] bridge: filtering via arp/ip/ip6tables is no longer available by                                                                                                                                                              default. Update your scripts to load br_netfilter if you need this.
[    1.676872] 8021q: 802.1Q VLAN Support v1.8
[    1.691737] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.700383] Freeing unused kernel memory: 212K
[    1.704912] This architecture does not have kernel memory protection.
[    2.503897] init: Console is alive
[    2.507952] init: - watchdog -
[    2.556518] random: fast init done
[    3.773436] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.923792] usbcore: registered new interface driver usbfs
[    3.929691] usbcore: registered new interface driver hub
[    3.935313] usbcore: registered new device driver usb
[    3.949989] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.959420] ehci-platform: EHCI generic platform driver
[    3.964894] ehci-platform ehci-platform.0: EHCI Host Controller
[    3.971092] ehci-platform ehci-platform.0: new USB bus registered, assigned b                                                                                                                                                             us number 1
[    3.979573] ehci-platform ehci-platform.0: irq 5, io mem 0x18004000
[    4.006566] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    4.014662] hub 1-0:1.0: USB hub found
[    4.019399] hub 1-0:1.0: 2 ports detected
[    4.029725] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.038024] ohci-platform: OHCI generic platform driver
[    4.043505] ohci-platform ohci-platform.0: Generic Platform OHCI controller
[    4.050751] ohci-platform ohci-platform.0: new USB bus registered, assigned b                                                                                                                                                             us number 2
[    4.059181] ohci-platform ohci-platform.0: irq 5, io mem 0x18009000
[    4.132189] hub 2-0:1.0: USB hub found
[    4.136982] hub 2-0:1.0: 2 ports detected
[    4.149179] kmodloader: done loading kernel modules from /etc/modules-boot.d/                                                                                                                                                             *
[    4.167951] init: - preinit -
[    6.084025] random: jshn: uninitialized urandom read (4 bytes read)
[    6.249093] random: jshn: uninitialized urandom read (4 bytes read)
[    6.298758] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.781101] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.829284] urandom-seed: Seed file not found (/etc/urandom.seed)
[    9.958832] procd: - early -
[    9.962027] procd: - watchdog -
[   10.694665] procd: - watchdog -
[   10.698818] procd: - ubus -
[   10.802622] urandom_read: 1 callbacks suppressed
[   10.802637] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.815770] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.823103] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.832101] procd: - init -
Please press Enter to activate this console.
[   12.044210] urngd: v1.0.0 started.
[   12.445149] random: crng init done
[   12.448719] random: 3 urandom warning(s) missed due to ratelimiting
[   12.475316] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.493608] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.520644] Loading modules backported from Linux version v4.19.85-0-gc63ee29                                                                                                                                                             39dc1
[   12.528441] Backport generated by backports.git v4.19.85-1-0-g8a8be258
[   12.540245] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.561502] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   12.668493] xt_time: kernel timezone is -0000
[   12.675766] bgmac_bcma bcma0:2: Found PHY addr: 30 (NOREGS)
[   12.794570] b53_common: found switch: BCM53115, rev 8
[   12.799974] libphy: bcma_mdio mii bus: probed
[   12.804431] bgmac_bcma bcma0:2: Support for Roboswitch not implemented
[   12.908468] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[   13.159998] PPP generic driver version 2.4.2
[   13.178841] NET: Registered protocol family 24
[   13.214701] b43-phy0: Broadcom 4716 WLAN found (core revision 17)
[   13.326009] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 5
[   13.332314] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 7, Versio                                                                                                                                                             n 0
[   13.340897] b43-phy1: Broadcom 4322 WLAN found (core revision 16)
[   13.510878] b43-phy1: Found PHY: Analog 8, Type 4 (N), Revision 4
[   13.517195] b43-phy1: Found Radio: Manuf 0x17F, ID 0x2056, Revision 3, Versio                                                                                                                                                             n 0
[   13.551196] Broadcom 43xx driver loaded [ Features: PNL ]
[   13.582500] kmodloader: done loading kernel modules from /etc/modules.d/*
[   44.975687] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   45.035256] br-lan: port 1(eth0.1) entered blocking state
[   45.040864] br-lan: port 1(eth0.1) entered disabled state
[   45.047053] device eth0.1 entered promiscuous mode
[   45.051949] device eth0 entered promiscuous mode
[   45.157072] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   45.279691] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   45.727047] jffs2: notice: (1269) jffs2_build_xattr_subsystem: complete build                                                                                                                                                             ing xattr subsystem, 71 of xdatum (3 unchecked, 68 orphan) and 144 of xref (75 d                                                                                                                                                             ead, 2 orphan) found.
[   46.007307] bgmac_bcma bcma0:2 eth0: Link is Up - 1Gbps/Full - flow control o                                                                                                                                                             ff
[   46.014836] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   46.086719] br-lan: port 1(eth0.1) entered blocking state
[   46.092236] br-lan: port 1(eth0.1) entered forwarding state
[   46.098652] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   46.206703] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   48.249755] overlayfs: upper fs does not support tmpfile.
Error loading shared library libubox.so: No such file or directory (needed by /sbin/uci)
Error loading shared library libubox.so: No such file or directory (needed by /lib/libuci.so)
Error relocating /lib/libuci.so: blob_nest_end: symbol not found
Error relocating /lib/libuci.so: blobmsg_open_nested: symbol not found
Error relocating /lib/libuci.so: blobmsg_add_field: symbol not found
Error relocating /lib/libuci.so: blobmsg_parse: symbol not found

When I try to open Luci Web it show this.
1

This error is repeated on all the commands (opkg, sysupgrade etc)

Error loading shared library libubox.so: No such file or directory (needed by /sbin/uci)
Error loading shared library libubox.so: No such file or directory (needed by /lib/libuci.so)
Error relocating /lib/libuci.so: blob_nest_end: symbol not found
Error relocating /lib/libuci.so: blobmsg_open_nested: symbol not found
Error relocating /lib/libuci.so: blobmsg_add_field: symbol not found
Error relocating /lib/libuci.so: blobmsg_parse: symbol not found

Stuck need Help restoring router to working state

Start with trying https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset, this may already help if this situation was caused by runtime upgrades of essential packages.

Given that you apparently have serial console access, you can also try to interrupt the CFE bootloader and upload/ flash a new firmware image from there (it's a tad complicated with CFE on these Linksys routers, but possible).

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.