I flashed TP-Link TL-WR741ND v1. It is fine but network restart is not working and during upgrade the configuration was reset to default.
Comment/observation, not a "bug report":
Archer C7 v2, USB connection of low-speed device (APC UPS):
The behavior with ath79 is the same as with ar71xx in that an intermediate hub is required to connect to the device.
An Anker USB 3.0, 4-port (unpowered) hub works.
In case anyone tries to search for it on the forums, here are typical log messages
2018 Sep 22 10:12:49 front info kernel: [ 68.540370] usb 1-1: new low-speed USB device number 4 using ehci-platform
[...]
2018 Sep 22 10:12:59 front err kernel: [ 79.074628] usb 1-1: device not accepting address 4, error -145
2018 Sep 22 10:12:59 front info kernel: [ 79.234619] usb 1-1: new low-speed USB device number 5 using ehci-platform
2018 Sep 22 10:28:46 front err kernel: [ 89.794601] usb 1-1: device not accepting address 5, error -145
2018 Sep 22 10:28:46 front err kernel: [ 89.800699] usb usb1-port1: unable to enumerate USB device
and the usb-related packages
$ sudo opkg list | fgrep usb
kmod-phy-ath79-usb - 4.14.67-1
kmod-usb-core - 4.14.67-1
kmod-usb-ehci - 4.14.67-1
kmod-usb-hid - 4.14.67-1
kmod-usb-ledtrig-usbport - 4.14.67-1
kmod-usb2 - 4.14.67-1
libusb-1.0 - 1.0.22-1
libusb-compat - 0.1.5-1
Keywords: apcupsd APC UPS SmartUPS Smart-UPS SUA1500 XL750
Currently, ath9k-leds seems to be broken in ath79.
WZR-HP-G450H has 3x ath9k-leds, but they have not appeared in /sys/class/leds/. And also, 7x ath9k-leds have not appearded in WZR-HP-AG300H. Of course, ath9k driver is installed.
/sys/kernel/debug/gpios (WZR-HP-AG300H):
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/18040000.gpio, 18040000.gpio:
gpio-1 ( |buffalo:red:diag ) out hi
gpio-2 ( |buffalo:power:usb ) out hi
gpio-3 ( |gpio-keys ) in hi
gpio-5 ( |gpio-keys ) in hi
gpio-6 ( |gpio-keys ) in hi
gpio-7 ( |gpio-keys ) in hi
gpio-8 ( |gpio-keys ) in hi
gpio-11 ( |gpio-keys ) in hi
gpiochip2: GPIOs 492-501, ath9k-phy1:
gpiochip1: GPIOs 502-511, ath9k-phy0:
After reversing following commit, LEDs again appeared:
1 Like
Confirm this bug in my wndr3700v2 - no wifi leds:
cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/18040000.gpio, 18040000.gpio:
gpio-0 ( |netgear:orange:wps ) out hi
gpio-1 ( |netgear:orange:power) out hi
gpio-2 ( |netgear:green:power ) out lo
gpio-3 ( |wps ) in hi
gpio-4 ( |netgear:green:wps ) out hi
gpio-5 ( |rtl8366s ) in hi
gpio-6 ( |netgear:green:wan ) out hi
gpio-7 ( |rtl8366s ) in hi
gpio-8 ( |reset ) in hi
gpio-11 ( |rfkill ) in hi
gpiochip2: GPIOs 492-501, ath9k-phy1:
gpiochip1: GPIOs 502-511, ath9k-phy0:
root@OpenWrt:~#
My build: OpenWrt SNAPSHOT, r8170-d8274451cb
Under OpenWrt SNAPSHOT r8055-6e80dd58bb wifi leds working OK, so this is version kernel issue - in older wifi leds work, in newest not.
1 Like
Some crack that adds support for Mikrotik SXT Lite 5 AC (RBSXT5HacD2n)?
Confirming the same observation with WNDR3800 on ath79 target.
ath9k wifi LEDs are dark.
Reverting the commit ccab68f2 from @nbd fixes ath9k wifi LEDs.
Apparently the ath9k LED functionality in ath79 requires the GPIO chip parent registration that got removed with ccab68f2
@nbd
Any ideas, what could be done in ath79 to return the ath9k LED functionality?
Hello
I am adding support for tl-wr841-v8 in tiny targets
Apart from the work needed for dts and etc scripts, the target have been added in tiny-tp-link.mk with this entry:
define Device/tplink_tl-wr841-v8
$(Device/tplink-4mlzma)
ATH_SOC := ar9341
DEVICE_TITLE := TP-LINK TL-WR841N/ND v8
TPLINK_HWID := 0x08410008
SUPPORTED_DEVICES += tl-wr841-v8
endef
TARGET_DEVICES += tplink_tl-wr841-v8
doing so the image generation works, but I only get:
menion@Menionubuntu:/media/storage/das1/temp/openwrt_ath79/bin/targets/ath79/tiny$ ls -la
total 3512
drwxr-xr-x 1 menion menion 280 Oct 16 16:52 .
drwxr-xr-x 1 menion menion 8 Oct 16 15:24 ..
-rw-r--r-- 1 menion menion 824 Oct 16 17:18 config.seed
-rw-r--r-- 1 menion menion 2893 Oct 16 17:23 openwrt-ath79-tiny-device-tplink-tl-wr841-v8.manifest
-rw-r--r-- 1 menion menion 3580071 Oct 16 17:23 openwrt-ath79-tiny-tplink_tl-wr841-v8-initramfs-kernel.bin
drwxr-xr-x 1 menion menion 3220 Oct 16 17:19 packages
-rw-r--r-- 1 menion menion 323 Oct 16 17:23 sha256sums
menion@Menionubuntu:/media/storage/das1/temp/openwrt_ath79/bin/targets/ath79/tiny$
This, looking at the size, should be sysupgrade, but shouldn't I get a factory and sysupgrade image, named with these suffix?
Any news about the fixing way of this bug?
All new build from ath79 target works without working wifi LED'S - and that bothers me
Like I wrote above, I have reverted the culprit commit in my own build so leds work again.
I have seen no reaction from @nbd so I guess that the Wi-Fi driver unloading possibility is seen as more important than the Wi-Fi led functionality.
Sorry, I didn't get around to looking into this yet. I hope to find the time to look into this the next few days.
6 Likes
How to correctly mount USB2 flashdrive ext4 on ath79 system? Migrated wr842ndv2 from ar71xx to ath79, copied fstab config as is. USB not mounting...
cat etc/config/fstab
config 'global'
option anon_swap '0'
option anon_mount '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
config 'mount'
option target 'opt'
option uuid 'e3f4e526-f8bd-d301-a0f4-e526f8bdd301'>
dmesg
[ 0.000000] Linux version 4.14.76 (@vm) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8340-80c61c161a)) #0 Tue Oct 16 14:07:41 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link TL-WR842N/ND v2
[ 0.000000] SoC: Atheros AR9341 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 804bbc40, node_mem_map 81007c60
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 26112K/32768K available (3461K kernel code, 143K rwdata, 864K rodata, 1220K init, 201K bss, 6656K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 535.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns
[ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns
[ 0.008247] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.094814] pid_max: default: 32768 minimum: 301
[ 0.099922] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.106917] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.119251] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.129664] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.136195] pinctrl core: initialized pinctrl subsystem
[ 0.142857] NET: Registered protocol family 16
[ 0.175779] clocksource: Switched to clocksource MIPS
[ 0.182375] NET: Registered protocol family 2
[ 0.187899] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.195264] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.202034] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.208901] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.215076] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.222072] NET: Registered protocol family 1
[ 0.226748] PCI: CLS 0 bytes, default 32
[ 0.231747] Crashlog allocated RAM at address 0x1f00000
[ 0.238887] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[ 0.251437] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.257639] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.278902] io scheduler noop registered
[ 0.283040] io scheduler deadline registered (default)
[ 0.288947] ar7200-usb-phy usb-phy: phy reset is missing
[ 0.296841] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[ 0.304791] gpio-export gpio-export: 1 gpio(s) exported
[ 0.311262] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.318868] console [ttyS0] disabled
[ 0.322692] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 1562500) is a 16550A
[ 0.331849] console [ttyS0] enabled
[ 0.339415] bootconsole [early0] disabled
[ 0.367588] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.372599] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.379193] Creating 3 MTD partitions on "spi0.0":
[ 0.384148] 0x000000000000-0x000000020000 : "u-boot"
[ 0.390299] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.412935] 2 tplink-fw partitions found on MTD device firmware
[ 0.419110] 0x000000020000-0x00000018de00 : "kernel"
[ 0.425158] 0x00000018de00-0x0000007f0000 : "rootfs"
[ 0.431180] mtd: device 3 (rootfs) set to be root filesystem
[ 0.437131] 1 squashfs-split partitions found on MTD device rootfs
[ 0.443526] 0x000000450000-0x0000007f0000 : "rootfs_data"
[ 0.450035] 0x0000007f0000-0x000000800000 : "art"
[ 0.457187] libphy: Fixed MDIO Bus: probed
[ 0.796204] libphy: ag71xx_mdio: probed
[ 1.086117] mdio-bus.0:1f: Found an AR934X built-in switch
[ 1.091986] libphy: ar7240sw_mdio: probed
[ 1.487735] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:00 [uid=004dd042, driver=Generic PHY]
[ 1.498293] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.837635] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.847733] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.856583] NET: Registered protocol family 17
[ 1.861257] 8021q: 802.1Q VLAN Support v1.8
[ 1.876128] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.891213] Freeing unused kernel memory: 1220K
[ 1.895923] This architecture does not have kernel memory protection.
[ 2.535791] random: fast init done
[ 2.694416] init: Console is alive
[ 2.698282] init: - watchdog -
[ 4.100938] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.270871] usbcore: registered new interface driver usbfs
[ 4.276717] usbcore: registered new interface driver hub
[ 4.282306] usbcore: registered new device driver usb
[ 4.332512] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.351070] SCSI subsystem initialized
[ 4.361053] ehci-platform: EHCI generic platform driver
[ 4.366832] ehci-platform 1b000000.usb: EHCI Host Controller
[ 4.372714] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 4.380968] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[ 4.415834] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 4.423270] hub 1-0:1.0: USB hub found
[ 4.427610] hub 1-0:1.0: 1 port detected
[ 4.437308] usbcore: registered new interface driver usb-storage
[ 4.444616] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.454282] init: - preinit -
[ 5.467780] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.651414] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.920899] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.123066] urandom_read: 4 callbacks suppressed
[ 7.123076] random: procd: uninitialized urandom read (4 bytes read)
[ 8.096927] eth1: link up (1000Mbps/Full duplex)
[ 11.360596] mount_root: loading kmods from internal overlay
[ 11.398791] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.407733] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.656783] jffs2: notice: (463) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (2 unchecked, 3 orphan) and 15 of xref (3 dead, 0 orphan) found.
[ 11.673403] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 11.685355] block: ignoring mount section cfg024d78 due to invalid target 'opt'
[ 11.693548] block: extroot: not configured
[ 11.737020] jffs2: notice: (461) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (2 unchecked, 3 orphan) and 15 of xref (3 dead, 0 orphan) found.
[ 11.889673] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 11.900632] block: ignoring mount section cfg024d78 due to invalid target 'opt'
[ 11.908816] block: extroot: not configured
[ 11.914165] mount_root: switching to jffs2 overlay
[ 11.948139] overlayfs: upper fs does not support tmpfile.
[ 11.959704] urandom-seed: Seeding with /etc/urandom.seed
[ 12.027208] procd: - early -
[ 12.030353] procd: - watchdog -
[ 12.335869] eth1: link down
[ 12.669640] procd: - watchdog -
[ 12.673237] procd: - ubus -
[ 12.794732] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.868061] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.877026] procd: - init -
[ 13.362203] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.376868] tun: Universal TUN/TAP device driver, 1.6
[ 13.388610] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85
[ 13.396602] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
[ 13.411038] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 13.491546] xt_time: kernel timezone is -0000
[ 13.523140] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.624314] ath: EEPROM regdomain: 0x0
[ 13.624325] ath: EEPROM indicates default country code should be used
[ 13.624330] ath: doing EEPROM country->regdmn map search
[ 13.624348] ath: country maps to regdmn code: 0x3a
[ 13.624355] ath: Country alpha2 being used: US
[ 13.624360] ath: Regpair used: 0x3a
[ 13.640288] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.642107] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=2
[ 13.756996] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 21.228977] eth1: link up (1000Mbps/Full duplex)
[ 21.248416] br-lan: port 1(eth1.1) entered blocking state
[ 21.254005] br-lan: port 1(eth1.1) entered disabled state
[ 21.259984] device eth1.1 entered promiscuous mode
[ 21.264943] device eth1 entered promiscuous mode
[ 21.286953] br-lan: port 1(eth1.1) entered blocking state
[ 21.292544] br-lan: port 1(eth1.1) entered forwarding state
[ 23.458300] eth0: link up (100Mbps/Full duplex)
[ 23.542286] ath: EEPROM regdomain: 0x81b8
[ 23.542297] ath: EEPROM indicates we should expect a country code
[ 23.542304] ath: doing EEPROM country->regdmn map search
[ 23.542311] ath: country maps to regdmn code: 0x37
[ 23.542319] ath: Country alpha2 being used: LT
[ 23.542324] ath: Regpair used: 0x37
[ 23.542331] ath: regdomain 0x81b8 dynamically updated by user
[ 27.452703] br-lan: port 2(wlan0) entered blocking state
[ 27.458289] br-lan: port 2(wlan0) entered disabled state
[ 27.464094] device wlan0 entered promiscuous mode
[ 28.818419] br-lan: port 2(wlan0) entered blocking state
[ 28.823926] br-lan: port 2(wlan0) entered forwarding state
[ 28.899502] br-lan: port 3(tap0) entered blocking state
[ 28.904913] br-lan: port 3(tap0) entered disabled state
[ 28.910752] device tap0 entered promiscuous mode
[ 28.915655] br-lan: port 3(tap0) entered blocking state
[ 28.921115] br-lan: port 3(tap0) entered forwarding state
[ 80.685281] random: crng init done>
opkg list-installed
base-files - 196-r8340-80c61c161a
block-mount - 2018-05-23-dd02dad3-3
blockd - 2018-05-23-dd02dad3-3
busybox - 1.29.3-3
dnsmasq - 2.80rc1-2
dropbear - 2017.75-8
etherwake - 1.09-4
firewall - 2018-08-13-1c4d5bcd-2
fstools - 2018-05-23-dd02dad3-3
fwtool - 1
hostapd-common - 2018-05-21-62566bc2-5
iptables - 1.6.2-3
iw - 4.14-1
iwinfo - 2018-07-31-65b8333f-1
jshn - 2018-07-25-c83a84af-2
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.14.76-1-9cc80a6ef9b694efa585ab89b3446157
kmod-ath - 4.14.76+4.19-rc5-1-1
kmod-ath9k - 4.14.76+4.19-rc5-1-1
kmod-ath9k-common - 4.14.76+4.19-rc5-1-1
kmod-cfg80211 - 4.14.76+4.19-rc5-1-1
kmod-crypto-crc32c - 4.14.76-1
kmod-crypto-hash - 4.14.76-1
kmod-fs-autofs4 - 4.14.76-1
kmod-fs-ext4 - 4.14.76-1
kmod-gpio-button-hotplug - 4.14.76-2
kmod-ipt-conntrack - 4.14.76-1
kmod-ipt-core - 4.14.76-1
kmod-ipt-nat - 4.14.76-1
kmod-ipt-offload - 4.14.76-1
kmod-lib-crc16 - 4.14.76-1
kmod-mac80211 - 4.14.76+4.19-rc5-1-1
kmod-nf-conntrack - 4.14.76-1
kmod-nf-flow - 4.14.76-1
kmod-nf-ipt - 4.14.76-1
kmod-nf-nat - 4.14.76-1
kmod-nf-reject - 4.14.76-1
kmod-nls-base - 4.14.76-1
kmod-phy-ath79-usb - 4.14.76-1
kmod-scsi-core - 4.14.76-1
kmod-tun - 4.14.76-1
kmod-usb-core - 4.14.76-1
kmod-usb-ehci - 4.14.76-1
kmod-usb-ledtrig-usbport - 4.14.76-1
kmod-usb-storage - 4.14.76-1
kmod-usb2 - 4.14.76-1
libblobmsg-json - 2018-07-25-c83a84af-2
libc - 1.1.20-1
libgcc - 7.3.0-1
libip4tc - 1.6.2-3
libiwinfo - 2018-07-31-65b8333f-1
libjson-c - 0.12.1-2
libjson-script - 2018-07-25-c83a84af-2
liblzo - 2.10-1
libnl-tiny - 0.1-5
libopenssl - 1.0.2p-1
libpthread - 1.1.20-1
libubox - 2018-07-25-c83a84af-2
libubus - 2018-10-06-221ce7e7-1
libuci - 2018-08-11-4c8b4d6e-1
libuclient - 2018-08-03-ae1c656f-1
libxtables - 1.6.2-3
logd - 2018-02-14-128bc35f-2
netifd - 2018-10-02-a117e414-2
openvpn-openssl - 2.4.5-7
openwrt-keyring - 2018-05-18-103a32e9-1
opkg - 2017-12-07-3b417b9f-2
procd - 2018-10-11-94944ab0-2
swconfig - 11
uboot-envtools - 2018.03-2
ubox - 2018-02-14-128bc35f-2
ubus - 2018-10-06-221ce7e7-1
ubusd - 2018-10-06-221ce7e7-1
uci - 2018-08-11-4c8b4d6e-1
uclient-fetch - 2018-08-03-ae1c656f-1
usign - 2015-07-04-ef641914-1
wireless-regdb - 2017-10-20-4343d359
wpad-basic - 2018-05-21-62566bc2-5>
Fix your setting.
Tried different targets. No use. Drive is not mounted
I see error in bootlog. Try edit fstab like this:
config 'mount'
option target '/data'
option uuid 'e3f4e526-f8bd-d301-a0f4-e526f8bdd301'
option fstype 'ext4'
option enabled '1'
Your storage device is detected? I cannot find any logs.
That is my problem. If I compile ar71xx it works, so it drive is functional. @leeandy did not work 
(logs the same)
The same. I will recompile with usbutils and check out. Thanks
@h8red
On my ath79 router, default mount point is /mnt/sda1. When i'm change mount point to example /opt, it worked too.
I think you need recheck partitions of usb device.
OpenWrt SNAPSHOT, r8340-80c61c161a
root@OpenWrt:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 5.5M 5.5M 0 100% /rom
tmpfs 60.9M 608.0K 60.3M 1% /tmp
/dev/mtdblock8 24.6M 1020.0K 23.6M 4% /overlay
overlayfs:/overlay 24.6M 1020.0K 23.6M 4% /
tmpfs 512.0K 0 512.0K 0% /dev
/dev/sda1 7.4G 17.0M 7.0G 0% /mnt/sda1
root@OpenWrt:~# ls /dev/sd*
/dev/sda /dev/sda1
root@OpenWrt:~# cat /etc/config/fstab
config global
option anon_swap '0'
option anon_mount '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
config mount
option target '/mnt/sda1'
option uuid '08d46a9c-6104-4f91-92dd-4cc994783870'
option enabled '1'
If i'm delete /opt directory, my bootlog doesn't same of you.
[ 14.331944] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.347373] block: extroot: not configured
[ 14.352498] mount_root: switching to jffs2 overlay
[ 14.429412] overlayfs: upper fs does not support tmpfile
root@OpenWrt:~# ls /opt
ls: /opt: No such file or directory
root@OpenWrt:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 5.5M 5.5M 0 100% /rom
tmpfs 60.9M 72.0K 60.9M 0% /tmp
/dev/mtdblock8 24.6M 1020.0K 23.6M 4% /overlay
overlayfs:/overlay 24.6M 1020.0K 23.6M 4% /
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:~# cat /etc/config/fstab
config global
option anon_swap '0'
option anon_mount '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
config mount
option target '/opt'
option uuid '08d46a9c-6104-4f91-92dd-4cc994783870'
option enabled '1'
df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.8M 2.8M 0 100% /rom
tmpfs 13.3M 464.0K 12.9M 3% /tmp
/dev/mtdblock4 3.6M 288.0K 3.3M 8% /overlay
overlayfs:/overlay 3.6M 288.0K 3.3M 8% /
tmpfs 512.0K 0 512.0K 0% /dev>
Maybe I need kmod-usb-ohci or kmod-usb-uhci packages?
Not need, -uhci/ohci for support legacy usb v1 devices.