This topic is to test and find any problem related to kernel 4.19 on platform ipq806x
There is a PR waiting to be approved and pushed with the required changes to adds support to a normal buildroot
1 Like
I have been running a couple builds of this since you posted it. No crashes, no reboots, and no issues related to the kernel, as far as I know. It also works with a fully preempt-able kernel.
on what router?
Just for the record, all fine on the nbg6817 (for the last 12 days) as well (disclaimer, I haven't looked into USB).
Sorry, R7800.
tested on:
- Buffalo WXR-2533DHP
- NEC Aterm WG2600HP
Most functions, including USB, seem to have no problem.
Can someone post a bootlog from start? Also we need to test usb
Buffalo WXR-2533DHP:
bootlog
BUFFALO WXR-2533DHP U-Boot Ver 1.14 (May 18 2015 - 13:24:36)
CPU: IPQ8064 clock 1.4 GHz
DRAM: DDR3 512 MiB clock 533 MHz
NAND: ECC 4 bits, 256 MiB
SF: Detected W25Q32 with page size 64 KiB, total 4 MiB
MMC:
In: serial
Out: serial
Err: serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net: MAC2 addr:74:3:bd:bc:1d:98
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
eth1
Memory Test Start
Pattern: 55555555
Pattern: AAAAAAAA
Pattern: 00000000
Memory Test Pass
Hit any key to stop autoboot: 0
Checking Bank1 Image ...
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
Bank1 Image is good
kernel_checksum is 0xf9922e9c , rootfs_checksum is 0xe9
Checking Bank2 Image ...
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
UBI Volume is empty
Bank2 Image is fail
NAND erase: device 0 offset 0x4000000, size 0x4000000
Erasing at 0x7fe0000 -- 100% complete.
OK
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI: create volume table (copy #2)
Creating dynamic volume kernel of size 5332992
Creating dynamic volume ubi_rootfs of size 31490048
Creating dynamic volume ubi_rootfs_data of size 5332992
Bank2 UBI Partition is Broken
Cpoy to Bank2 Image from Bank1 Image
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
2482537 bytes written to volume kernel
11964457 bytes written to volume ubi_rootfs
MMC Device 0 not found
dmagic1 ffffffff dmagic2 ffffffff
MMC Device 0 not found
Using nand device 1
Device 1: nand1... is now current device
bootargs=console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
Booting from flash
set mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x4000000@0x0(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel && bootm 0x44000000
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
Image Name: ARM OpenWrt Linux-4.19.79
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2482473 Bytes = 2.4 MiB
Load Address: 42208000
Entry Point: 42208000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Setting up atags for msm partition: rootfs
device nand0 <nand0>, # parts = 1
#: name size offset mask_flags
0: fs 0x04000000 0x00000000 0
active partition: nand0,0 - (fs) 0x04000000 @ 0x00000000
defaults:
mtdids : none
mtdparts: none
Using machid 0x1260 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.79 (musashino205@Taiha.Net) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r0+11321-c1cf99794d)) #0 SMP Thu Oct 24 04:43:39 2019
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Buffalo WXR-2533DHP
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x80/0x47c with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29964 r8192 d23284 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800
[ 0.000000] Kernel command line: ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 477932K/491520K available (5286K kernel code, 180K rwdata, 1364K rodata, 1024K init, 228K bss, 13588K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (6279 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 181 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 229 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000022] Switching to timer-based delay loop, resolution 160ns
[ 0.000258] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000282] pid_max: default: 32768 minimum: 301
[ 0.000453] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000473] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001302] CPU: Testing write buffer coherency: ok
[ 0.002442] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.002619] rcu: Hierarchical SRCU implementation.
[ 0.003461] smp: Bringing up secondary CPUs ...
[ 0.005389] smp: Brought up 1 node, 2 CPUs
[ 0.005408] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.005417] CPU: All CPU(s) started in SVC mode.
[ 0.015909] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.016070] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016098] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.016263] pinctrl core: initialized pinctrl subsystem
[ 0.017411] NET: Registered protocol family 16
[ 0.017734] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.019128] cpuidle: using governor ladder
[ 0.019200] cpuidle: using governor menu
[ 0.042651] usbcore: registered new interface driver usbfs
[ 0.042734] usbcore: registered new interface driver hub
[ 0.042823] usbcore: registered new device driver usb
[ 0.042884] pps_core: LinuxPPS API ver. 1 registered
[ 0.042897] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.042931] PTP clock support registered
[ 0.044569] clocksource: Switched to clocksource dg_timer
[ 0.047930] NET: Registered protocol family 2
[ 0.048506] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.048542] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.048581] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.048635] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.048735] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.048765] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.048999] NET: Registered protocol family 1
[ 0.050329] No memory allocated for crashlog
[ 0.050602] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.057068] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.057088] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.066422] io scheduler noop registered
[ 0.066443] io scheduler deadline registered (default)
[ 0.069549] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.069669] qcom-pcie 1b500000.pci: Linked as a consumer to regulator.0
[ 0.069698] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.069810] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.070110] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.070169] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.070201] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.290044] qcom-pcie 1b500000.pci: Link up
[ 0.290208] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.290232] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.290253] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.290269] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.294524] PCI: bus0: Fast back to back transfers disabled
[ 0.300598] PCI: bus1: Fast back to back transfers disabled
[ 0.300703] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.300729] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.300858] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.300884] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.301486] pcieport 0000:00:00.0: AER enabled with IRQ 35
[ 0.301991] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.302108] qcom-pcie 1b700000.pci: Linked as a consumer to regulator.0
[ 0.302134] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.302245] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.302506] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.302558] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.302584] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.532088] qcom-pcie 1b700000.pci: Link up
[ 0.532246] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.532268] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.532292] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.536532] PCI: bus0: Fast back to back transfers disabled
[ 0.538695] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 0.542656] PCI: bus1: Fast back to back transfers disabled
[ 0.542747] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.542772] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.542906] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.542928] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.543460] pcieport 0001:00:00.0: AER enabled with IRQ 37
[ 0.545937] L2 @ QSB rate. Forcing new rate.
[ 0.546165] L2 @ 384000 KHz
[ 0.546349] CPU0 @ 800000 KHz
[ 0.546362] CPU1 @ QSB rate. Forcing new rate.
[ 0.546490] CPU1 @ 384000 KHz
[ 0.550161] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.551516] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[ 0.553171] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.554069] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.554121] msm_serial 16340000.serial: uartclk = 7372800
[ 0.554192] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 38, base_baud = 460800) is a MSM
[ 0.554232] msm_serial: console setup on port #0
[ 1.323644] console [ttyMSM0] enabled
[ 1.328761] msm_serial: driver initialized
[ 1.337257] loop: module loaded
[ 1.339323] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 1.339357] nand: Micron MT29F2G08ABBEAH4
[ 1.345889] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.349768] 2 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.357263] Creating 2 MTD partitions on "qcom_nand.0":
[ 1.364042] 0x000000000000-0x000004000000 : "ubi"
[ 1.377521] random: fast init done
[ 1.537233] 0x000004000000-0x000008000000 : "rootfs_1"
[ 1.705874] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 1.720674] m25p80 spi0.0: w25q32dw (4096 Kbytes)
[ 1.720824] 13 fixed-partitions partitions found on MTD device spi0.0
[ 1.724359] Creating 13 MTD partitions on "spi0.0":
[ 1.730866] 0x000000000000-0x000000010000 : "SBL1"
[ 1.736402] 0x000000010000-0x000000030000 : "MIBIB"
[ 1.741100] 0x000000030000-0x000000060000 : "SBL2"
[ 1.745998] 0x000000060000-0x000000090000 : "SBL3"
[ 1.750726] 0x000000090000-0x0000000a0000 : "DDRCONFIG"
[ 1.755635] 0x0000000a0000-0x0000000b0000 : "SSD"
[ 1.760650] 0x0000000b0000-0x0000000e0000 : "TZ"
[ 1.765563] 0x0000000e0000-0x000000100000 : "RPM"
[ 1.770185] 0x000000100000-0x000000170000 : "APPSBL"
[ 1.774772] 0x000000170000-0x000000180000 : "APPSBLENV"
[ 1.779892] 0x000000180000-0x0000001c0000 : "ART"
[ 1.784844] 0x0000001c0000-0x0000001d0000 : "BOOTCONFIG"
[ 1.789661] 0x0000001d0000-0x000000240000 : "APPSBL_1"
[ 1.795975] mdio-gpio soc:mdio: failed to get alias id
[ 1.799301] libphy: GPIO Bitbanged MDIO: probed
[ 1.825738] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.678137] ar8327: qca,phy-rgmii-en is not specified
[ 2.678526] libphy: Fixed MDIO Bus: probed
[ 2.683789] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 2.687003] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 2.692685] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 2.700231] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 2.706052] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 2.713688] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 2.721668] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 2.727477] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 2.734779] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 2.741630] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 2.749192] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 2.756220] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.764191] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 2.771419] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 2.777429] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 2.784775] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 2.790676] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 2.798395] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 2.806297] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 2.812037] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 2.819479] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 2.826268] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 2.833736] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 2.840847] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.847752] i2c /dev entries driver
[ 2.856565] Calibration not found.
[ 2.860554] Speed bin: 0
[ 2.862291] PVS bin: 1
[ 2.867666] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.868002] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.875485] sdhci: Secure Digital Host Controller Interface driver
[ 2.881652] sdhci: Copyright(c) Pierre Ossman
[ 2.887992] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.895874] NET: Registered protocol family 10
[ 2.901229] Segment Routing with IPv6
[ 2.902456] NET: Registered protocol family 17
[ 2.906549] 8021q: 802.1Q VLAN Support v1.8
[ 2.910507] Registering SWP/SWPB emulation handler
[ 2.941913] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 2.968382] s1a: supplied by regulator-dummy
[ 2.968548] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.972173] s1b: supplied by regulator-dummy
[ 2.976885] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.981316] s2a: supplied by regulator-dummy
[ 2.986084] s2a: Bringing 0uV into 800000-800000uV
[ 2.990528] s2b: supplied by regulator-dummy
[ 2.994929] s2b: Bringing 0uV into 800000-800000uV
[ 3.001529] cpu cpu0: Linked as a consumer to regulator.4
[ 3.003878] cpu cpu0: Dropping the link to regulator.4
[ 3.009652] cpu cpu0: Linked as a consumer to regulator.4
[ 3.015010] cpu cpu1: Linked as a consumer to regulator.5
[ 3.022846] UBI: auto-attach mtd0
[ 3.025223] ubi0: attaching mtd0
[ 3.176018] random: crng init done
[ 4.059092] ubi0: scanning is finished
[ 4.082354] ubi0: attached mtd0 (name "ubi", size 64 MiB)
[ 4.082375] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.086797] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.093495] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.100404] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[ 4.107184] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 4.113375] ubi0: max/mean erase counter: 12/4, WL threshold: 4096, image sequence number: 0
[ 4.120461] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 40
[ 4.129415] block ubiblock0_1: created from ubi0:1(ubi_rootfs)
[ 4.130052] ubi0: background thread "ubi_bgt0d" started, PID 63
[ [ 4.157599] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.160426] Freeing unused kernel memory: 1024K
[ 4.186167] Run /sbin/init as init process
[ 4.823246] init: Console is alive
[ 4.823376] init: - watchdog -
[ 6.797660] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.977759] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.980194] SCSI subsystem initialized
[ 6.989677] ehci-platform: EHCI generic platform driver
[ 6.991345] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.994169] ohci-platform: OHCI generic platform driver
[ 7.005148] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
[ 7.056768] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
[ 7.114346] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 7.114425] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 7.119124] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 7.126494] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x11000000
[ 7.136859] hub 1-0:1.0: USB hub found
[ 7.141584] hub 1-0:1.0: 1 port detected
[ 7.145652] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 7.149464] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 7.154756] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 7.162478] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.169299] hub 2-0:1.0: USB hub found
[ 7.177231] hub 2-0:1.0: 1 port detected
[ 7.180989] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.184864] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 7.190226] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 7.197725] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x10000000
[ 7.207680] hub 3-0:1.0: USB hub found
[ 7.212933] hub 3-0:1.0: 1 port detected
[ 7.217013] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.220818] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 7.226160] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 7.233732] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.240651] hub 4-0:1.0: USB hub found
[ 7.248619] hub 4-0:1.0: 1 port detected
[ 7.255113] usbcore: registered new interface driver usb-storage
[ 7.256736] usbcore: registered new interface driver uas
[ 7.262208] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.275147] init: - preinit -
[ 9.843276] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 9.845416] dwmac1000: Master AXI performs any burst length
[ 9.852192] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 9.857674] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 9.865854] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 9.875554] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.956190] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 10.956292] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 13.171886] mount_root: loading kmods from internal overlay
[ 13.189302] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 13.190556] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 23.142473] UBIFS (ubi0:2): default file-system created
[ 23.146237] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 151
[ 23.455040] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 23.455092] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 23.461881] UBIFS (ubi0:2): FS size: 43552768 bytes (41 MiB, 343 LEBs), journal size 2158592 bytes (2 MiB, 17 LEBs)
[ 23.471916] UBIFS (ubi0:2): reserved for root: 2057104 bytes (2008 KiB)
[ 23.482101] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID ED81BFF0-A26B-4D40-821E-BFA459B2E460, small LPT model
[ 23.502503] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 23.502606] block: unable to load configuration (fstab: Entry not found)
[ 23.508366] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 23.515352] block: unable to load configuration (fstab: Entry not found)
[ 23.521577] block: attempting to load /etc/config/fstab
[ 23.530077] block: unable to load configuration (fstab: Entry not found)
[ 23.533296] block: no usable configuration
[ 23.595031] UBIFS (ubi0:2): un-mount UBI device 0
[ 23.595170] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 23.615911] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 152
[ 23.805954] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 23.805992] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 23.812775] UBIFS (ubi0:2): FS size: 43552768 bytes (41 MiB, 343 LEBs), journal size 2158592 bytes (2 MiB, 17 LEBs)
[ 23.822799] UBIFS (ubi0:2): reserved for root: 2057104 bytes (2008 KiB)
[ 23.833013] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID ED81BFF0-A26B-4D40-821E-BFA459B2E460, small LPT model
[ 29.601387] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 29.601541] block: unable to load configuration (fstab: Entry not found)
[ 29.607379] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 29.614221] block: unable to load configuration (fstab: Entry not found)
[ 29.620609] block: attempting to load /etc/config/fstab
[ 29.627526] block: unable to load configuration (fstab: Entry not found)
[ 29.632215] block: no usable configuration
[ 29.678663] mount_root: overlay filesystem has not been fully initialized yet
[ 29.679305] mount_root: switching to ubifs overlay
[ 29.730724] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
[ 29.733863] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 29.927411] procd: - early -
[ 29.927600] procd: - watchdog -
[ 30.613580] procd: - watchdog -
[ 30.613848] procd: - ubus -
[ 30.789999] procd: - init -
Please press Enter to activate this console.
[ 31.183225] kmodloader: loading kernel modules from /etc/modules.d/*
[ 31.230805] urngd: v1.0.1 started.
[ 31.246620] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 31.251569] nat46: module (version 683fbd2b765506332a1af141545652bf58f03166) loaded.
[ 31.279283] Mirror/redirect action on
[ 31.282934] u32 classifier
[ 31.282949] input device check on
[ 31.284519] Actions configured
[ 31.298337] fuse init (API version 7.27)
[ 31.300779] Loading modules backported from Linux version v5.4-rc2-0-gda0c9ea146cb
[ 31.301321] Backport generated by backports.git v5.4-rc2-1-0-g5a0c323a
[ 31.320768] usbcore: registered new interface driver ums-alauda
[ 31.321422] usbcore: registered new interface driver ums-cypress
[ 31.326232] usbcore: registered new interface driver ums-datafab
[ 31.332373] usbcore: registered new interface driver ums-freecom
[ 31.338764] usbcore: registered new interface driver ums-isd200
[ 31.344536] usbcore: registered new interface driver ums-jumpshot
[ 31.350402] usbcore: registered new interface driver ums-karma
[ 31.356616] usbcore: registered new interface driver ums-sddr09
[ 31.362179] usbcore: registered new interface driver ums-sddr55
[ 31.368431] usbcore: registered new interface driver ums-usbat
[ 31.387716] xt_time: kernel timezone is -0000
[ 31.427803] PPP generic driver version 2.4.2
[ 31.428566] NET: Registered protocol family 24
[ 31.440255] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x40.
[ 31.440727] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 31.447718] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 31.772987] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[ 31.964480] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 32.021523] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 32.084661] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 32.595437] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 32.595472] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 32.606148] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-012-54863dff api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 423fbbe8
[ 32.676877] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 33.863609] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 33.863638] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 33.940647] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 33.940700] ath10k_pci 0000:01:00.0: wmi print 'free: 34228 iram: 33108 sram: 6252'
[ 34.128012] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 34.278699] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x40.
[ 34.280051] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 34.286585] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 34.892009] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[ 35.095913] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 35.164464] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 35.230047] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 35.231159] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 35.238016] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 35.250545] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-012-54863dff api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 423fbbe8
[ 35.320453] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[ 36.517041] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 36.517074] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 36.596179] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 36.596237] ath10k_pci 0001:01:00.0: wmi print 'free: 34228 iram: 33108 sram: 6252'
[ 36.820476] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 36.957197] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 47.700990] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 47.701742] dwmac1000: Master AXI performs any burst length
[ 47.709971] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 47.715357] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 47.723338] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 47.732423] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 47.746747] br-lan: port 1(eth1.1) entered blocking state
[ 47.746779] br-lan: port 1(eth1.1) entered disabled state
[ 47.751309] device eth1.1 entered promiscuous mode
[ 47.756599] device eth1 entered promiscuous mode
[ 47.764353] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 47.770808] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 47.772883] dwmac1000: Master AXI performs any burst length
[ 47.781863] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 47.787238] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 47.795305] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 47.804504] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 47.827682] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 48.795242] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 48.797345] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 48.803300] br-lan: port 1(eth1.1) entered blocking state
[ 48.809253] br-lan: port 1(eth1.1) entered forwarding state
[ 48.833204] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 48.874986] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 48.875033] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 48.888585] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
BusyBox v1.31.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r0+11321-c1cf99794d
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
Is that the same as the kernel log in LuCI? If not, where can I grab it?
Kernel log from Luci is sufficient
ZyXEL NBG6817/ ipq8065 (I had to strip the timestamps, to keep it within posting limits):
Booting Linux on physical CPU 0x0
Linux version 4.19.79 (slh@trident) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r11240-9d5e266cb1)) #0 SMP Wed Oct 16 15:13:39 2019
CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
OF: fdt: Machine model: ZyXEL NBG6817
Memory policy: Data cache writealloc
On node 0 totalpages: 122880
Normal zone: 1080 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 122880 pages, LIFO batch:31
random: get_random_bytes called from start_kernel+0x80/0x47c with crng_init=0
percpu: Embedded 15 pages/cpu s30476 r8192 d22772 u61440
pcpu-alloc: s30476 r8192 d22772 u61440 alloc=15*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists, mobility grouping on. Total pages: 121800
Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p8
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p8 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 477932K/491520K available (5348K kernel code, 186K rwdata, 1368K rodata, 1024K init, 230K bss, 13588K reserved, 0K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0x(ptrval) - 0x(ptrval) (6341 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 187 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 231 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
Switching to timer-based delay loop, resolution 160ns
Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=6250)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x42300000 - 0x42300060
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs ...
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (25.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
clocksource: Switched to clocksource dg_timer
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 64
No memory allocated for crashlog
workingset: timestamp_bits=14 max_order=17 bucket_order=3
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
qcom-pcie 1b500000.pci: Linked as a consumer to regulator.0
qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
qcom-pcie 1b500000.pci: Parsing ranges property...
qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
qcom-pcie 1b500000.pci: Link up
qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
pci_bus 0000:00: scanning bus
pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
pci 0000:00:00.0: supports D1
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
pci_bus 0000:00: fixups for bus
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
pci_bus 0000:01: scanning bus
pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci_bus 0000:01: fixups for bus
PCI: bus1: Fast back to back transfers disabled
pci_bus 0000:01: bus scan returning with max=01
pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
pci_bus 0000:00: bus scan returning with max=ff
pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
pcieport 0000:00:00.0: assign IRQ: got 35
pcieport 0000:00:00.0: AER enabled with IRQ 36
qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
qcom-pcie 1b700000.pci: Linked as a consumer to regulator.0
qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
qcom-pcie 1b700000.pci: Parsing ranges property...
qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
qcom-pcie 1b700000.pci: Link up
qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
pci_bus 0001:00: root bus resource [bus 00-ff]
pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
pci_bus 0001:00: scanning bus
pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
pci 0001:00:00.0: supports D1
pci 0001:00:00.0: PME# supported from D0 D1 D3hot
pci 0001:00:00.0: PME# disabled
pci_bus 0001:00: fixups for bus
PCI: bus0: Fast back to back transfers disabled
pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
pci_bus 0001:01: scanning bus
pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
pci 0001:01:00.0: PME# disabled
pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
pci_bus 0001:01: fixups for bus
PCI: bus1: Fast back to back transfers disabled
pci_bus 0001:01: bus scan returning with max=01
pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
pci_bus 0001:00: bus scan returning with max=ff
pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
pci 0001:00:00.0: PCI bridge to [bus 01-ff]
pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
pcieport 0001:00:00.0: assign IRQ: got 37
pcieport 0001:00:00.0: AER enabled with IRQ 38
L2 @ QSB rate. Forcing new rate.
L2 @ 384000 KHz
CPU0 @ 800000 KHz
CPU1 @ QSB rate. Forcing new rate.
CPU1 @ 384000 KHz
gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
msm_serial 16340000.serial: msm_serial: detected port #0
msm_serial 16340000.serial: uartclk = 7372800
16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
msm_serial: console setup on port #0
console [ttyMSM0] enabled
msm_serial: driver initialized
loop: module loaded
spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
m25p80 spi0.0: mx25u3235f (4096 Kbytes)
13 qcom-smem partitions found on MTD device spi0.0
Creating 13 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "0:SBL1"
0x000000020000-0x000000040000 : "0:MIBIB"
0x000000040000-0x000000060000 : "0:SBL2"
0x000000060000-0x0000000a0000 : "0:SBL3"
0x0000000a0000-0x0000000b0000 : "0:DDRCONFIG"
0x0000000b0000-0x0000000c0000 : "0:SSD"
0x0000000c0000-0x000000100000 : "0:TZ"
0x000000100000-0x000000140000 : "0:RPM"
0x000000140000-0x0000001c0000 : "0:APPSBL"
0x0000001c0000-0x0000001d0000 : "0:APPSBLENV"
0x0000001d0000-0x0000001e0000 : "0:ART"
0x0000001e0000-0x0000001f0000 : "0:DUAL_FLAG"
0x0000001f0000-0x000000400000 : "0:RESERVED"
libphy: GPIO Bitbanged MDIO: probed
switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
ar8327: qca,phy-rgmii-en is not specified
libphy: Fixed MDIO Bus: probed
ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
ipq806x-gmac-dwmac 37200000.ethernet (unnamed net_device) (uninitialized): device MAC address 5a:0a:60:78:0e:25
ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
ipq806x-gmac-dwmac 37400000.ethernet (unnamed net_device) (uninitialized): device MAC address 22:de:5f:8c:22:f2
i2c /dev entries driver
Calibration not found.
Speed bin: 0
PVS bin: 5
cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
mmci-pl18x 12400000.sdcc: Linked as a consumer to regulator.1
mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 34,0 (pio)
mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
Registering SWP/SWPB emulation handler
qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
s1a: supplied by regulator-dummy
s1a: Bringing 0uV into 1050000-1050000uV
s1b: supplied by regulator-dummy
s1b: Bringing 0uV into 1050000-1050000uV
s2a: supplied by regulator-dummy
s2a: Bringing 0uV into 775000-775000uV
s2b: supplied by regulator-dummy
s2b: Bringing 0uV into 775000-775000uV
cpu cpu0: Linked as a consumer to regulator.4
cpu cpu0: Dropping the link to regulator.4
cpu cpu0: Linked as a consumer to regulator.4
cpu cpu1: Linked as a consumer to regulator.5
hctosys: unable to open rtc device (rtc0)
Waiting for root device /dev/mmcblk0p8...
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 S10004 3.56 GiB
mmcblk0boot0: mmc0:0001 S10004 partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 S10004 partition 2 4.00 MiB
mmcblk0rpmb: mmc0:0001 S10004 partition 3 4.00 MiB, chardev (248:0)
mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
VFS: Mounted root (squashfs filesystem) readonly on device 179:8.
Freeing unused kernel memory: 1024K
Run /sbin/init as init process
random: fast init done
init: Console is alive
init: - watchdog -
kmodloader: loading kernel modules from /etc/modules-boot.d/*
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
SCSI subsystem initialized
libata version 3.00 loaded.
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform: OHCI generic platform driver
dwc3 11000000.dwc3: Failed to get clk 'ref': -2
dwc3 10000000.dwc3: Failed to get clk 'ref': -2
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
xhci-hcd xhci-hcd.0.auto: irq 44, io mem 0x11000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
xhci-hcd xhci-hcd.1.auto: irq 45, io mem 0x10000000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver uas
kmodloader: done loading kernel modules from /etc/modules-boot.d/*
init: - preinit -
usb 3-1: new high-speed USB device number 2 using xhci-hcd
random: jshn: uninitialized urandom read (4 bytes read)
random: jshn: uninitialized urandom read (4 bytes read)
random: procd: uninitialized urandom read (4 bytes read)
usb-storage 3-1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 3-1:1.0
scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Attached SCSI removable disk
Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
dwmac1000: Master AXI performs any burst length
ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
mount_root: loading kmods from internal overlay
kmodloader: loading kernel modules from //etc/modules-boot.d/*
kmodloader: done loading kernel modules from //etc/modules-boot.d/*
random: crng init done
random: 3 urandom warning(s) missed due to ratelimiting
block: attempting to load /etc/config/fstab
block: unable to load configuration (fstab: Entry not found)
block: no usable configuration
EXT4-fs (loop0): recovery complete
EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
mount_root: loading kmods from internal overlay
kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
block: attempting to load /etc/config/fstab
block: unable to load configuration (fstab: Entry not found)
block: no usable configuration
mount_root: switching to ext4 overlay
urandom-seed: Seeding with /etc/urandom.seed
procd: - early -
procd: - watchdog -
procd: - watchdog -
procd: - ubus -
procd: - init -
urngd: v1.0.0 started.
EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts:
kmodloader: loading kernel modules from /etc/modules.d/*
NET: Registered protocol family 15
Initializing XFRM netlink socket
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
Loading modules backported from Linux version v5.4-rc2-0-gda0c9ea146cb
Backport generated by backports.git v5.4-rc2-1-0-g5a0c323a
usbcore: registered new interface driver usblp
wireguard: WireGuard 0.0.20191012 loaded. See www.wireguard.com for information.
wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
xt_time: kernel timezone is -0000
PPP generic driver version 2.4.2
NET: Registered protocol family 24
ath10k_pci 0000:01:00.0: assign IRQ: got 35
ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0000:01:00.0: enabling bus mastering
ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fH-012-54863dff2 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,htt-mgt-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 ad847b78
ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
ath10k_pci 0000:01:00.0: wmi print 'free: 81784 iram: 23636 sram: 14184'
ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ath10k_pci 0001:01:00.0: assign IRQ: got 37
ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0001:01:00.0: enabling bus mastering
ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fH-012-54863dff2 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,htt-mgt-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 ad847b78
ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
ath10k_pci 0001:01:00.0: wmi print 'free: 81784 iram: 23636 sram: 14184'
ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
kmodloader: done loading kernel modules from /etc/modules.d/*
Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
dwmac1000: Master AXI performs any burst length
ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
br-lan: port 1(eth1.1) entered blocking state
br-lan: port 1(eth1.1) entered disabled state
device eth1.1 entered promiscuous mode
device eth1 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth1.12: link is not ready
Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
dwmac1000: Master AXI performs any burst length
ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0.11: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth1.10: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0.7: link is not ready
ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
br-lan: port 1(eth1.1) entered blocking state
br-lan: port 1(eth1.1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): eth1.10: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth1.12: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth0.7: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth0.11: link becomes ready
ath: EEPROM regdomain: 0x8114
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: DE
ath: Regpair used: 0x37
ath: regdomain 0x8114 dynamically updated by user
ath: EEPROM regdomain: 0x8114
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: DE
ath: Regpair used: 0x37
ath: regdomain 0x8114 dynamically updated by user
ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
ath10k_pci 0001:01:00.0: wmi print 'free: 81784 iram: 23636 sram: 14184'
ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
pppoe-wan: renamed from ppp0
ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
ath10k_pci 0000:01:00.0: wmi print 'free: 81784 iram: 23636 sram: 14184'
ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
br-lan: port 2(wlan1) entered blocking state
br-lan: port 2(wlan1) entered disabled state
device wlan1 entered promiscuous mode
br-lan: port 3(wlan0) entered blocking state
br-lan: port 3(wlan0) entered disabled state
device wlan0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
br-lan: port 2(wlan1) entered blocking state
br-lan: port 2(wlan1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
br-lan: port 3(wlan0) entered blocking state
br-lan: port 3(wlan0) entered forwarding state
1 Like
ok i needed to check if there were some error with cpuidle, cpufreq or tsense
Is there an image for R7800? Happy to flash and give it a go.
R7800 (IPQ8065)
[0.000000] Booting Linux on physical CPU 0x0
[0.000000] Linux version 4.19.79 (dmichael@dmichael-VirtualBox) (gcc version 9.2.0 (OpenWrt GCC 9.2.0 r11254-54d9ac8ba8)) #0 SMP PREEMPT Sat Oct 19 15:46:35 2019
[0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[0.000000] CPU: div instructions available: patching division code
[0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[0.000000] Memory policy: Data cache writealloc
[0.000000] On node 0 totalpages: 122880
[0.000000] Normal zone: 1080 pages used for memmap
[0.000000] Normal zone: 0 pages reserved
[0.000000] Normal zone: 122880 pages, LIFO batch:31
[0.000000] random: get_random_bytes called from start_kernel+0x80/0x4a4 with crng_init=0
[0.000000] percpu: Embedded 15 pages/cpu s30860 r8192 d22388 u61440
[0.000000] pcpu-alloc: s30860 r8192 d22388 u61440 alloc=15*4096
[0.000000] pcpu-alloc: [0] 0 [0] 1
[0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800
[0.000000] Kernel command line:
[0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[0.000000] Memory: 475880K/491520K available (5314K kernel code, 182K rwdata, 1376K rodata, 1024K init, 228K bss, 15640K reserved, 0K cma-reserved, 0K highmem)
[0.000000] Virtual kernel memory layout:
[0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[0.000000] .text : 0x(ptrval) - 0x(ptrval) (6307 kB)
[0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 183 kB)
[0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 229 kB)
[0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[0.000000] rcu: Preemptible hierarchical RCU implementation.
[0.000000] Tasks RCU enabled.
[0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[0.000024] Switching to timer-based delay loop, resolution 160ns
[0.000248] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=6250)
[0.000273] pid_max: default: 32768 minimum: 301
[0.000452] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[0.000473] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[0.001496] CPU: Testing write buffer coherency: ok
[0.008035] Setting up static identity map for 0x42300000 - 0x42300060
[0.010244] rcu: Hierarchical SRCU implementation.
[0.014741] smp: Bringing up secondary CPUs ...
[0.025079] smp: Brought up 1 node, 2 CPUs
[0.025097] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[0.025110] CPU: All CPU(s) started in SVC mode.
[0.036205] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[0.036521] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[0.036550] futex hash table entries: 512 (order: 3, 32768 bytes)
[0.036785] pinctrl core: initialized pinctrl subsystem
[0.038002] NET: Registered protocol family 16
[0.038389] DMA: preallocated 256 KiB pool for atomic coherent allocations
[0.039873] cpuidle: using governor ladder
[0.039946] cpuidle: using governor menu
[0.065404] usbcore: registered new interface driver usbfs
[0.065611] usbcore: registered new interface driver hub
[0.065738] usbcore: registered new device driver usb
[0.065799] pps_core: LinuxPPS API ver. 1 registered
[0.065816] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[0.065852] PTP clock support registered
[0.067716] clocksource: Switched to clocksource dg_timer
[0.071455] NET: Registered protocol family 2
[0.072220] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[0.072264] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[0.072304] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[0.072361] TCP: Hash tables configured (established 4096 bind 4096)
[0.072462] UDP hash table entries: 256 (order: 1, 8192 bytes)
[0.072496] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[0.072729] NET: Registered protocol family 1
[0.072786] PCI: CLS 0 bytes, default 64
[0.074237] No memory allocated for crashlog
[0.074535] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[0.081516] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[0.081532] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[0.100318] io scheduler noop registered
[0.100340] io scheduler deadline registered (default)
[0.104186] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[0.104306] qcom-pcie 1b500000.pci: Linked as a consumer to regulator.0
[0.104334] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[0.104444] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[0.104724] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[0.104751] qcom-pcie 1b500000.pci: Parsing ranges property...
[0.104785] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[0.104892] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
[0.324068] qcom-pcie 1b500000.pci: Link up
[0.324258] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[0.324283] pci_bus 0000:00: root bus resource [bus 00-ff]
[0.324305] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[0.324323] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[0.324340] pci_bus 0000:00: scanning bus
[0.324389] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[0.324530] pci 0000:00:00.0: supports D1
[0.324541] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[0.324559] pci 0000:00:00.0: PME# disabled
[0.328905] pci_bus 0000:00: fixups for bus
[0.328929] PCI: bus0: Fast back to back transfers disabled
[0.328951] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[0.329093] pci_bus 0000:01: scanning bus
[0.329272] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[0.329624] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[0.330904] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[0.330946] pci 0000:01:00.0: PME# disabled
[0.335260] pci_bus 0000:01: fixups for bus
[0.335331] PCI: bus1: Fast back to back transfers disabled
[0.335350] pci_bus 0000:01: bus scan returning with max=01
[0.335368] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[0.335385] pci_bus 0000:00: bus scan returning with max=ff
[0.335436] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[0.335464] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[0.335593] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[0.335619] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[0.335943] pcieport 0000:00:00.0: assign IRQ: got 35
[0.336327] pcieport 0000:00:00.0: AER enabled with IRQ 36
[0.336963] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[0.337090] qcom-pcie 1b700000.pci: Linked as a consumer to regulator.0
[0.337120] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[0.337236] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[0.337513] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[0.337535] qcom-pcie 1b700000.pci: Parsing ranges property...
[0.337563] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
[0.337593] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[0.556022] qcom-pcie 1b700000.pci: Link up
[0.556180] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[0.556201] pci_bus 0001:00: root bus resource [bus 00-ff]
[0.556218] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[0.556233] pci_bus 0001:00: scanning bus
[0.556275] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[0.556400] pci 0001:00:00.0: supports D1
[0.556410] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[0.556423] pci 0001:00:00.0: PME# disabled
[0.560618] pci_bus 0001:00: fixups for bus
[0.560641] PCI: bus0: Fast back to back transfers disabled
[0.560660] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[0.560798] pci_bus 0001:01: scanning bus
[0.561083] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[0.561455] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[0.562723] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[0.562767] pci 0001:01:00.0: PME# disabled
[0.563073] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[0.567216] pci_bus 0001:01: fixups for bus
[0.567293] PCI: bus1: Fast back to back transfers disabled
[0.567310] pci_bus 0001:01: bus scan returning with max=01
[0.567327] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[0.567344] pci_bus 0001:00: bus scan returning with max=ff
[0.567383] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[0.567408] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[0.567543] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[0.567565] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[0.567764] pcieport 0001:00:00.0: assign IRQ: got 37
[0.568227] pcieport 0001:00:00.0: AER enabled with IRQ 38
[0.571067] L2 @ QSB rate. Forcing new rate.
[0.571295] L2 @ 384000 KHz
[0.571478] CPU0 @ 800000 KHz
[0.571492] CPU1 @ QSB rate. Forcing new rate.
[0.571622] CPU1 @ 384000 KHz
[0.575919] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[0.578289] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[0.579221] msm_serial 16340000.serial: msm_serial: detected port #0
[0.579275] msm_serial 16340000.serial: uartclk = 7372800
[0.579345] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
[0.579385] msm_serial: console setup on port #0
[1.339356] console [ttyMSM0] enabled
[1.344392] msm_serial: driver initialized
[1.353525] loop: module loaded
[1.355729] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[1.355762] nand: AMD/Spansion S34MS01G2
[1.362178] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[1.366170] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[1.373450] Creating 8 MTD partitions on "qcom_nand.0":
[1.380320] 0x000000000000-0x000000c80000 : "qcadata"
[1.391055] random: fast init done
[1.408628] 0x000000c80000-0x000001180000 : "APPSBL"
[1.418575] 0x000001180000-0x000001200000 : "APPSBLENV"
[1.420457] 0x000001200000-0x000001340000 : "art"
[1.425902] 0x000001340000-0x000001480000 : "artbak"
[1.430638] 0x000001480000-0x000001880000 : "kernel"
[1.440649] 0x000001880000-0x000007900000 : "ubi"
[1.613388] 0x000007900000-0x000008000000 : "reserve"
[1.628311] libphy: GPIO Bitbanged MDIO: probed
[1.651062] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[2.464778] ar8327: qca,phy-rgmii-en is not specified
[2.465272] libphy: Fixed MDIO Bus: probed
[2.471165] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[2.473578] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[2.479436] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[2.486894] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[2.492694] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[2.500407] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[2.508315] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[2.514118] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[2.521499] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[2.528268] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[2.535837] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[2.542860] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[2.551000] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[2.559470] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[2.564058] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[2.571510] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[2.577322] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[2.585033] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[2.592947] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[2.598778] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[2.606157] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[2.612929] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[2.620456] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[2.627485] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[2.634522] i2c /dev entries driver
[2.643306] Calibration not found.
[2.646743] Speed bin: 0
[2.649042] PVS bin: 3
[2.653720] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[2.654005] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[2.661735] sdhci: Secure Digital Host Controller Interface driver
[2.668374] sdhci: Copyright(c) Pierre Ossman
[2.674626] sdhci-pltfm: SDHCI platform and OF driver helper
[2.681765] NET: Registered protocol family 10
[2.687645] Segment Routing with IPv6
[2.689156] NET: Registered protocol family 17
[2.693248] 8021q: 802.1Q VLAN Support v1.8
[2.697203] Registering SWP/SWPB emulation handler
[2.733457] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[2.751445] s1a: supplied by regulator-dummy
[2.751605] s1a: Bringing 0uV into 1050000-1050000uV
[2.755350] s1b: supplied by regulator-dummy
[2.759992] s1b: Bringing 0uV into 1050000-1050000uV
[2.764512] s2a: supplied by regulator-dummy
[2.769151] s2a: Bringing 0uV into 775000-775000uV
[2.773691] s2b: supplied by regulator-dummy
[2.778052] s2b: Bringing 0uV into 775000-775000uV
[2.783916] thermal thermal_zone0: failed to read out thermal zone (-110)
[2.787983] cpu cpu0: Linked as a consumer to regulator.4
[2.793948] cpu cpu0: Dropping the link to regulator.4
[2.799500] cpu cpu0: Linked as a consumer to regulator.4
[2.805082] cpu cpu1: Linked as a consumer to regulator.5
[2.811556] UBI: auto-attach mtd6
[2.815070] ubi0: attaching mtd6
[2.903754] random: crng init done
[3.637991] ubi0: scanning is finished
[3.648945] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[3.648966] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[3.653390] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[3.660144] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[3.667038] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[3.673764] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[3.680030] ubi0: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 342339688
[3.687074] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[3.696202] ubi0: background thread "ubi_bgt0d" started, PID 66
[3.706093] block ubiblock0_0: created from ubi0:0(rootfs)
[3.711119] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[3.716661] hctosys: unable to open rtc device (rtc0)
[3.728657] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[3.729809] Freeing unused kernel memory: 1024K
[3.735126] Run /sbin/init as init process
[4.168282] init: Console is alive
[4.168401] init: - watchdog -
[5.943961] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[6.008689] exFAT: Version 1.2.9
[6.019491] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[6.021678] SCSI subsystem initialized
[6.028900] libata version 3.00 loaded.
[6.030941] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[6.030985] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[6.035422] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[6.044960] scsi host0: ahci
[6.052396] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
[6.372691] ata1: SATA link down (SStatus 0 SControl 300)
[6.377184] ehci-platform: EHCI generic platform driver
[6.381237] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[6.383337] ohci-platform: OHCI generic platform driver
[6.392023] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
[6.431460] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
[6.477170] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[6.477258] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[6.482086] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[6.489238] xhci-hcd xhci-hcd.0.auto: irq 43, io mem 0x11000000
[6.499188] hub 1-0:1.0: USB hub found
[6.504479] hub 1-0:1.0: 1 port detected
[6.508489] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[6.512383] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[6.517640] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[6.525274] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[6.532085] hub 2-0:1.0: USB hub found
[6.540080] hub 2-0:1.0: 1 port detected
[6.543961] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[6.547704] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[6.553126] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[6.560554] xhci-hcd xhci-hcd.1.auto: irq 44, io mem 0x10000000
[6.570432] hub 3-0:1.0: USB hub found
[6.575828] hub 3-0:1.0: 1 port detected
[6.579884] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[6.583733] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[6.588992] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[6.596632] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[6.603437] hub 4-0:1.0: USB hub found
[6.611471] hub 4-0:1.0: 1 port detected
[6.617693] usbcore: registered new interface driver usb-storage
[6.619139] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[6.627640] init: - preinit -
[8.726503] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[8.727378] dwmac1000: Master AXI performs any burst length
[8.735569] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[8.740834] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp spported
[8.748939] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[8.758187] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[9.770441] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[9.772421] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
...Part 2:
[ 14.946352] mount_root: loading kmods from internal overlay
[ 14.982785] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 14.985556] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 14.999135] print_req_error: I/O error, dev mtdblock0, sector 0
[ 15.000334] print_req_error: I/O error, dev mtdblock0, sector 8
[ 15.005146] print_req_error: I/O error, dev mtdblock0, sector 16
[ 15.011258] print_req_error: I/O error, dev mtdblock0, sector 24
[ 15.017790] print_req_error: I/O error, dev mtdblock0, sector 0
[ 15.022021] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.109371] print_req_error: I/O error, dev mtdblock0, sector 0
[ 15.109399] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.115502] print_req_error: I/O error, dev mtdblock1, sector 0
[ 15.122595] print_req_error: I/O error, dev mtdblock1, sector 8
[ 15.128499] print_req_error: I/O error, dev mtdblock1, sector 16
[ 15.134388] print_req_error: I/O error, dev mtdblock1, sector 24
[ 15.140644] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.150678] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.415708] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 157
[ 15.480145] UBIFS (ubi0:1): recovery needed
[ 15.616616] UBIFS (ubi0:1): recovery completed
[ 15.616761] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.620045] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.628003] UBIFS (ubi0:1): FS size: 83042304 bytes (79 MiB, 654 LEBs), journal size 4190208 bytes (3 MiB, 33 LEBs)
[ 15.637817] UBIFS (ubi0:1): reserved for root: 3922293 bytes (3830 KiB)
[ 15.648101] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 255D4CD0-797F-44E8-A0F2-1C852239FE51, small LPT model
[ 15.656524] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 15.678276] block: extroot: not configured
[ 15.684005] UBIFS (ubi0:1): un-mount UBI device 0
[ 15.684052] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 15.694720] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 158
[ 15.922074] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.922105] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.929020] UBIFS (ubi0:1): FS size: 83042304 bytes (79 MiB, 654 LEBs), journal size 4190208 bytes (3 MiB, 33 LEBs)
[ 15.938876] UBIFS (ubi0:1): reserved for root: 3922293 bytes (3830 KiB)
[ 15.949139] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 255D4CD0-797F-44E8-A0F2-1C852239FE51, small LPT model
[ 15.963105] mount_root: loading kmods from internal overlay
[ 16.000083] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 16.002464] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 16.022923] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 16.029551] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 16.036972] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 16.041279] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 16.305404] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 16.312248] block: extroot: not configured
[ 16.325810] mount_root: switching to ubifs overlay
[ 16.355700] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
[ 16.359636] urandom-seed: Seeding with /etc/urandom.seed
[ 16.478668] procd: - early -
[ 16.478780] procd: - watchdog -
[ 17.094968] procd: - watchdog -
[ 17.095650] procd: - ubus -
[ 17.252407] procd: - init -
[ 17.578572] urngd: v1.0.0 started.
[ 17.645212] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.663280] tun: Universal TUN/TAP device driver, 1.6
[ 17.665370] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 17.669972] gre: GRE over IPv4 demultiplexor driver
[ 17.673929] ip_gre: GRE over IPv4 tunneling driver
[ 17.739976] Mirror/redirect action on
[ 17.743644] u32 classifier
[ 17.743660] input device check on
[ 17.745306] Actions configured
[ 17.755557] fuse init (API version 7.27)
[ 17.758708] usbcore: registered new interface driver chaoskey
[ 17.759577] Loading modules backported from Linux version v5.4-rc2-0-gda0c9ea146cb
[ 17.764410] Backport generated by backports.git v5.4-rc2-1-0-g5a0c323a
[ 17.784203] usbcore: registered new interface driver usbserial_generic
[ 17.784258] usbserial: USB Serial support registered for generic
[ 17.805337] xt_time: kernel timezone is -0000
[ 17.834450] PPP generic driver version 2.4.2
[ 17.836309] PPP MPPE Compression module registered
[ 17.838671] NET: Registered protocol family 24
[ 17.843913] PPTP driver version 0.8.5
[ 17.857604] ath10k_pci 0000:01:00.0: assign IRQ: got 35
[ 17.857624] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
[ 17.858227] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 17.864549] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 17.865154] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 18.891826] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[ 18.935113] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 19.000136] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 19.069573] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 19.450504] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 19.450565] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 19.463112] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-012-54863dff2 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 97790349
[ 21.787485] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[ 27.630271] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 27.630314] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 27.712218] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 27.713057] ath10k_pci 0000:01:00.0: wmi print 'free: 81768 iram: 23364 sram: 14184'
[ 27.938536] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 28.032397] ath: EEPROM regdomain: 0x0
[ 28.032401] ath: EEPROM indicates default country code should be used
[ 28.032404] ath: doing EEPROM country->regdmn map search
[ 28.032410] ath: country maps to regdmn code: 0x3a
[ 28.032414] ath: Country alpha2 being used: US
[ 28.032417] ath: Regpair used: 0x3a
[ 28.034194] ath10k_pci 0001:01:00.0: assign IRQ: got 37
[ 28.034215] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
[ 28.037039] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 28.041260] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 28.041896] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 28.531238] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[ 28.595814] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 28.657139] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 28.716807] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 28.717157] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 28.725795] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 28.737656] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-012-54863dff2 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 97790349
[ 31.061569] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
[ 36.900608] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 36.900644] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 36.984383] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 36.985255] ath10k_pci 0001:01:00.0: wmi print 'free: 81768 iram: 23364 sram: 14184'
[ 37.223785] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 37.318536] ath: EEPROM regdomain: 0x0
[ 37.318541] ath: EEPROM indicates default country code should be used
[ 37.318543] ath: doing EEPROM country->regdmn map search
[ 37.318549] ath: country maps to regdmn code: 0x3a
[ 37.318553] ath: Country alpha2 being used: US
[ 37.318556] ath: Regpair used: 0x3a
[ 37.323018] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 42.877157] print_req_error: 14 callbacks suppressed
[ 42.877164] print_req_error: I/O error, dev mtdblock0, sector 0
[ 42.882526] print_req_error: I/O error, dev mtdblock0, sector 8
[ 42.893186] print_req_error: I/O error, dev mtdblock0, sector 16
[ 42.894688] print_req_error: I/O error, dev mtdblock0, sector 24
[ 42.904648] print_req_error: I/O error, dev mtdblock0, sector 0
[ 42.904987] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 42.919782] print_req_error: I/O error, dev mtdblock0, sector 0
[ 42.919817] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 42.929922] print_req_error: I/O error, dev mtdblock1, sector 0
[ 42.933288] print_req_error: I/O error, dev mtdblock1, sector 8
[ 42.942710] print_req_error: I/O error, dev mtdblock1, sector 16
[ 42.945114] print_req_error: I/O error, dev mtdblock1, sector 24
[ 42.955292] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 42.960235] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 43.906209] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 43.907367] dwmac1000: Master AXI performs any burst length
[ 43.921466] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 43.921506] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 43.936412] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 43.939012] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 43.956911] br-lan: port 1(eth1.1) entered blocking state
[ 43.957018] br-lan: port 1(eth1.1) entered disabled state
[ 43.970267] device eth1.1 entered promiscuous mode
[ 43.970298] device eth1 entered promiscuous mode
[ 43.984132] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 44.005204] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 44.006418] dwmac1000: Master AXI performs any burst length
[ 44.015566] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 44.030003] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 44.030562] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 44.042579] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 44.048201] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 44.970095] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 44.970157] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 44.984276] br-lan: port 1(eth1.1) entered blocking state
[ 44.984310] br-lan: port 1(eth1.1) entered forwarding state
[ 45.000563] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 45.096965] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 45.097027] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 45.121398] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 53.467932] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 53.467965] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 53.559559] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 53.560447] ath10k_pci 0001:01:00.0: wmi print 'free: 81768 iram: 23364 sram: 14184'
[ 53.956676] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 53.956971] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 54.466602] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 60.009272] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 60.009309] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 60.091254] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 60.092107] ath10k_pci 0000:01:00.0: wmi print 'free: 81768 iram: 23364 sram: 14184'
[ 60.445165] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 60.445745] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 60.459903] br-lan: port 2(wlan1) entered blocking state
[ 60.461004] br-lan: port 2(wlan1) entered disabled state
[ 60.470679] device wlan1 entered promiscuous mode
[ 60.496756] br-lan: port 3(wlan0) entered blocking state
[ 60.496863] br-lan: port 3(wlan0) entered disabled state
[ 60.524320] device wlan0 entered promiscuous mode
[ 60.856452] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 60.856591] br-lan: port 2(wlan1) entered blocking state
[ 60.861929] br-lan: port 2(wlan1) entered forwarding state
[ 61.210919] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 61.211212] br-lan: port 3(wlan0) entered blocking state
[ 61.216411] br-lan: port 3(wlan0) entered forwarding state
[ 61.240304] br-lan: port 4(wlan0-1) entered blocking state
[ 61.240359] br-lan: port 4(wlan0-1) entered disabled state
[ 61.247007] device wlan0-1 entered promiscuous mode
[ 61.278674] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 61.278708] br-lan: port 4(wlan0-1) entered blocking state
[ 61.283830] br-lan: port 4(wlan0-1) entered forwarding state
[ 61.373597] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 65.406748] ath10k_pci 0000:01:00.0: Invalid peer id 1 or peer stats buffer, peer: e4a93ffc sta: (null)
[ 1690.358576] ath10k_pci 0000:01:00.0: Invalid VHT mcs 15 peer stats
I tested this today on the r7500v2.
I loaded via an initramfs as this patch set does not expand overlay for the r7500v2. Any other r7500v2 user who might use this patch set coming from master, 18.xx, or 19.xx will have to flash an image via tftp (i.e. do not flash a sysupgrade image) otherwise the router will brick (easily recoverable tho).
Can't test usb this way but cpuidle (both wfi and spc) and tsens look ok to me.
git log
commit 9ce6873e659f07a42e676147c2018570a38e4097 (HEAD -> ansuel-k419)
Author: Ansuel Smith <ansuelsmth@gmail.com>
Date: Mon Sep 16 12:56:21 2019 +0200
ipq806x: adds kernel 4.19 support
Based on https://git.openwrt.org/?p=openwrt/staging/chunkeey.git;a=commit;h=c096b58311b52068cfa90d437d1bcfaf7fcd0d2e
Fixed broken tsens driver
Fixed bootloop on ipq8065 soc with CPU_IDLE enabled
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
commit f96af28272ee7056d04c7b5ea79a8a6f26b96340 (upstream/master, origin/master, master)
Author: Koen Vandeputte <koen.vandeputte@ncentric.com>
Date: Tue Nov 5 12:16:58 2019 +0100
ath10k-firmware: update Candela Tech firmware images
...
tsens and cpuidle status:
BusyBox v1.31.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r11413+1-f96af28272
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# uname -a
Linux OpenWrt 4.19.81 #0 SMP Tue Nov 5 17:09:37 2019 armv7l GNU/Linux
root@OpenWrt:/# uptime
17:10:24 up 0 min, load average: 0.40, 0.14, 0.05
root@OpenWrt:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp
44112
root@OpenWrt:/# cat /sys/devices/virtual/thermal/thermal_zone9/temp
47985
root@OpenWrt:/# cat /sys/devices/system/cpu/cpuidle/current_driver
arm_idle
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu0/cpuidle/state0/name
WFI
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu0/cpuidle/state0/usage
972
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu1/cpuidle/state0/name
WFI
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu1/cpuidle/state0/usage
958
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu0/cpuidle/state1/name
spc
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu0/cpuidle/state1/usage
1388
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu1/cpuidle/state1/name
spc
root@OpenWrt:/# cat /sys/devices/system/cpu/cpu1/cpuidle/state1/usage
1563
1 Like
We finally did it... The pr is in the staging tree and approved 
6 Likes