IPQ5018: Adding OpenWrt support for Lite-On WPX8324-BT

For Developers
1

I am requesting assistance adding for Lite-On WPX8324-BT.

This is an IPQ5018 device with 2 1G LAN.

Specifications :

  1. CHIPSET: IPQ5018
  2. RAM : ESMT M15T4G16256A 4 Gigabit (512MByte)
  3. NOR flash: MX25U12835F 128Mbit (16 MByte)
  4. NAND flash: Winbond W25N01GW 128 MByte
  5. 2.4GHz: IPQ5018 (integrated)
  6. 5GHz radio: QCN6122
  7. Serial Baud Rate : 115200 bps

For now, I only can get the OEM bootlog because the RX serial header is disconnected or missing 1 component (capasitor or resistor) on C9509 label so I can't interrupt the bootloader or activate the console.

The serial layout should be like this :

Ethernet side

^

^

RX (TP14?)

TX (TP15)

NOT CONNECTED

GND (TP17)

^

^

LED side

I've try another test point (TP) and jumper the C9509 label but it didn't work.

Thanks, Arif.

2

Here's the bootlog :

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00066
S - IMAGE_VARIANT_STRING=MAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002c1
B -       127 - PBL, Start
B -      1559 - bootable_media_detect_entry, Start
B -      1736 - bootable_media_detect_success, Start
B -      1741 - elf_loader_entry, Start
B -     10165 - auth_hash_seg_entry, Start
B -     10522 - auth_hash_seg_exit, Start
B -    174932 - elf_segs_hash_verify_entry, Start
B -    237603 - PBL, End
B -    192699 - SBL1, Start
B -    254065 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    262391 - clock_init, Start
D -      7228 - clock_init, Delta
B -    269803 - boot_flash_init, Start
D -      2745 - boot_flash_init, Delta
B -    273859 - boot_config_data_table_init, Start
D -       793 - boot_config_data_table_init, Delta - (575 Bytes)
B -    287005 - Boot Setting :  0x00030618
B -    289872 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:4
B -    300303 - sbl1_ddr_set_params, Start
B -    305396 - Pre_DDR_clock_init, Start
B -    307196 - Pre_DDR_clock_init, End
B -    954101 - do ddr sanity test, Start
D -        61 - do ddr sanity test, Delta
B -    958767 - Image Load, Start
D -    132980 - QSEE Image Loaded, Delta - (578956 Bytes)
B -   1092601 - Image Load, Start
D -      5765 - DEVCFG Image Loaded, Delta - (13592 Bytes)
B -   1098762 - Image Load, Start
D -     99186 - APPSBL Image Loaded, Delta - (412086 Bytes)
B -   1198040 - QSEE Execution, Start
D -        30 - QSEE Execution, Delta
B -   1204506 - SBL1, End
D -   1014277 - SBL1, Delta
S - Flash Throughput, 4760 KB/s  (1005881 Bytes,  211295 us)
S - DDR Frequency, 800 MHz
S - Core 0 Frequency, 800 MHz




U-Boot 2016.01 (Oct 25 2023 - 02:56:42 -0400)



DRAM:  smem ram ptable found: ver: 1 len: 4

512 MiB

NAND:  QPIC controller support serial NAND

ID = 21baef

Vendor = ef

Device = ba

Serial Nand Device Found With ID : 0xef 0xba

Serial NAND device Manufacturer:W25N01GW

Device Size:128 MiB, Page size:2048, Spare Size:64, ECC:4-bit

SPI_ADDR_LEN=3

SF: Detected MX25U12835F with page size 256 Bytes, erase size 64 KiB, total 16 MiB

ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000

144 MiB

MMC:   sdhci: Node Not found, skipping initialization



PCI Link Intialized

In:    serial@78AF000

Out:   serial@78AF000

Err:   serial@78AF000

WPX8324 U-Boot Bv0.0.1 



machid: 8040004

GPIO settings

Hit any key to stop autoboot:  5  4  3  2  1  0 

ubi0: attaching mtd2

ubi0: scanning is finished

ubi0: attached mtd2 (name "mtd=0", size 62 MiB)

ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

ubi0: good PEBs: 496, bad PEBs: 0, corrupted PEBs: 0

ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128

ubi0: max/mean erase counter: 116/36, WL threshold: 4096, image sequence number: 1560982293

ubi0: available PEBs: 0, total reserved PEBs: 496, PEBs reserved for bad PEB handling: 20

Read 0 bytes from volume kernel to 44000000

No size specified -> Using max size (4363412)

## Loading kernel from FIT Image at 44000000 ...

   Using 'config@mp03.5-c1' configuration

   Trying 'kernel@1' kernel subimage

     Description:  ARM OpenWrt Linux-4.4.60

     Type:         Kernel Image

     Compression:  lzma compressed

     Data Start:   0x440000e4

     Data Size:    2925689 Bytes = 2.8 MiB

     Architecture: ARM

     OS:           Linux

     Load Address: 0x41208000

     Entry Point:  0x41208000

     Hash algo:    crc32

     Hash value:   b777fb0d

     Hash algo:    sha1

     Hash value:   1b5f588a80092a860b35ddde7e5768c03c63ae5f

   Verifying Hash Integrity ... crc32+ sha1+ OK

## Loading fdt from FIT Image at 44000000 ...

   Using 'config@mp03.5-c1' configuration

   Trying 'fdt@mp03.5-c1' fdt subimage

     Description:  ARM OpenWrt qcom-ipq50xx-mpxx device tree blob

     Type:         Flat Device Tree

     Compression:  uncompressed

     Data Start:   0x443202d4

     Data Size:    59393 Bytes = 58 KiB

     Architecture: ARM

     Hash algo:    crc32

     Hash value:   40989b91

     Hash algo:    sha1

     Hash value:   c37ea4678b828487ab4271f35060447696b42f28

   Verifying Hash Integrity ... crc32+ sha1+ OK

   Booting using the fdt blob at 0x443202d4

   Uncompressing Kernel Image ... OK

   Loading Device Tree to 4a3ee000, end 4a3ff800 ... OK

Using machid 0x8040004 from environment



Starting kernel ...



[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.60 (abloomy@Ubuntu16-04-qsdk) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 unknown) ) #137 SMP PREEMPT Mon Jul 29 04:38:00 EDT 2024
[    0.000000] CPU: ARMv7 Processor [51af8014] revision 4 (ARMv7), cr=10c0383d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.5-C1
[    0.000000] Ignoring memory range 0x40000000 - 0x41000000
[    0.000000] Reserved memory: not enough space all defined regions.
[    0.000000] Reserved memory: not enough space all defined regions.
[    0.000000] Reserved memory: not enough space all defined regions.
[    0.000000] Reserved memory: not enough space all defined regions.
[    0.000000] Reserved memory: OVERLAP DETECTED!
[    0.000000] q6_mem_regions@4B000000 (0x4b000000--0x50400000) overlaps with q6_code_data@4B000000 (0x4b000000--0x4b060000)
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 11 pages/cpu @9eb5f000 s14400 r8192 d22464 u45056
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 102308
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 cnss2.skip_radio_bmap=2 cnss2.bdf_pci0=0xb0 cnss2.bdf_pci1=0x60 cnss2.bdf_integrated=0x24 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 398280K/413696K available (6302K kernel code, 350K rwdata, 1896K rodata, 1024K init, 442K bss, 15416K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0x9f800000 - 0xff800000   (1536 MB)
[    0.000000]     lowmem  : 0x80000000 - 0x9f000000   ( 496 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80208000 - 0x80b01bc0   (9191 kB)
[    0.000000]       .init : 0x80c00000 - 0x80d00000   (1024 kB)
[    0.000000]       .data : 0x80d00000 - 0x80d57a18   ( 351 kB)
[    0.000000]        .bss : 0x80d5a000 - 0x80dc8998   ( 443 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] GICv2m: Node v2m: range[0xb00a000:0xb00affc], SPI[448:480]
[    0.000000] GICv2m: Node v2m: range[0xb00b000:0xb00bffc], SPI[480:512]
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000018] Switching to timer-based delay loop, resolution 41ns
[    0.000519] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000535] pid_max: default: 32768 minimum: 301
[    0.000653] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000666] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001344] Initializing cgroup subsys io
[    0.001370] Initializing cgroup subsys memory
[    0.001405] Initializing cgroup subsys devices
[    0.001420] Initializing cgroup subsys freezer
[    0.001435] Initializing cgroup subsys net_cls
[    0.001447] Initializing cgroup subsys pids
[    0.001496] CPU: Testing write buffer coherency: ok
[    0.001949] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002020] Setting up static identity map for 0x41300000 - 0x41300058
[    0.052681] MSM Memory Dump base table set up
[    0.052716] MSM Memory Dump apps data table set up
[    0.090452] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.090588] Brought up 2 CPUs
[    0.090606] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.090613] CPU: All CPU(s) started in SVC mode.
[    0.105732] VFP support v0.3: implementor 51 architecture 3 part 40 variant 3 rev 4
[    0.106115] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.106150] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.106429] pinctrl core: initialized pinctrl subsystem
[    0.107990] NET: Registered protocol family 16
[    0.109475] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.140260] cpuidle: using governor ladder
[    0.170283] cpuidle: using governor menu
[    0.170613] NET: Registered protocol family 42
[    0.175620] qcom,gcc-ipq5018 1800000.gcc: Registered ipq5018 GCC clocks provider
[    0.180964] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.182471] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.196725] CPU: IPQ5018, SoC Version: 1.1
[    0.198736] IPC logging disabled
[    0.198750] IPC logging disabled
[    0.198755] IPC logging disabled
[    0.198760] IPC logging disabled
[    0.198764] IPC logging disabled
[    0.199036] sps:sps is ready.
[    0.232740] pps_core: LinuxPPS API ver. 1 registered
[    0.232754] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.232782] PTP clock support registered
[    0.234948] Advanced Linux Sound Architecture Driver Initialized.
[    0.235999] clocksource: Switched to clocksource arch_sys_counter
[    0.238733] NET: Registered protocol family 2
[    0.239663] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.239721] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.239796] TCP: Hash tables configured (established 4096 bind 4096)
[    0.239860] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.239886] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.240102] NET: Registered protocol family 1
[    0.249804] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.249825] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.255017] Key type asymmetric registered
[    0.255040] Asymmetric key parser 'x509' registered
[    0.255088] io scheduler noop registered
[    0.255102] io scheduler deadline registered (default)
[    0.264735] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[    0.265281] bt_driver 1943008.bt: bt_parse_ipc
[    0.265353] bt_driver 1943008.bt: bt_parse_mem
[    0.265400] bt_driver 1943008.bt: bt_parse_dt operating in secure mode
[    0.266760] 58000.qcom,msm-eud: ttyEUD0 at MMIO 0x0 (irq = 155, base_baud = 0) is a EUD UART
[    0.268319] Registered Sucessfully 
[    0.268989] msm_serial 78af000.serial: msm_serial: detected port #0
[    0.269052] msm_serial 78af000.serial: uartclk = 1843199
[    0.269110] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 20, base_baud = 115199) is a MSM
[    0.269144] msm_serial: console setup on port #0
[    0.954856] console [ttyMSM0] enabled
[    0.960095] msm_serial: driver initialized
[    0.963511] msm_serial_hsl_init: driver initialized
[    0.981008] brd: module loaded
[    0.988295] loop: module loaded
[    0.989083] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    0.991517] spi_qup 78b7000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    0.999823] m25p80 spi32766.0: found mx25u12835f, expected n25q128a11
[    1.004568] m25p80 spi32766.0: mx25u12835f (16384 Kbytes)
[    1.011088] 18 ofpart partitions found on MTD device spi32766.0
[    1.016320] Creating 18 MTD partitions on "spi32766.0":
[    1.022012] 0x000000000000-0x000000030000 : "0:SBL1"
[    1.028501] 0x000000030000-0x000000040000 : "0:MIBIB"
[    1.033506] 0x000000040000-0x000000050000 : "0:BOOTCONFIG"
[    1.038496] 0x000000050000-0x000000060000 : "0:BOOTCONFIG1"
[    1.043801] 0x000000060000-0x000000100000 : "0:QSEE"
[    1.049536] 0x000000100000-0x0000001a0000 : "0:QSEE_1"
[    1.054488] 0x0000001a0000-0x0000001b0000 : "0:DEVCFG"
[    1.059553] 0x0000001b0000-0x0000001c0000 : "0:DEVCFG_1"
[    1.064589] 0x0000001c0000-0x0000001d0000 : "0:CDT"
[    1.070155] 0x0000001d0000-0x0000001e0000 : "0:CDT_1"
[    1.074710] 0x0000001e0000-0x0000001f0000 : "0:APPSBLENV"
[    1.079904] 0x0000001f0000-0x000000290000 : "0:APPSBL"
[    1.085194] 0x000000290000-0x000000330000 : "0:APPSBL_1"
[    1.090317] 0x000000330000-0x0000003a0000 : "0:ART"
[    1.095737] 0x0000003a0000-0x0000003c0000 : "0:boarddata"
[    1.100433] 0x0000003c0000-0x0000007c0000 : "0:USERCONFIG"
[    1.105919] 0x0000007c0000-0x000000bc0000 : "0:data"
[    1.111375] 0x000000bc0000-0x000000c40000 : "0:dump"
[    1.117667] QPIC controller hw version Major:2, Minor:1
[    1.120268] QPIC controller support serial nand.
[    1.125530] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xba
[    1.130123] nand: Winbond W25N01GW SPI NAND 1.8V 1G-BIT
[    1.136437] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.141945] 3 ofpart partitions found on MTD device qcom_nand.0
[    1.149047] Creating 3 MTD partitions on "qcom_nand.0":
[    1.154828] 0x000000000000-0x000000080000 : "0:TRAINING"
[    1.161722] 0x000000080000-0x000003e80000 : "rootfs"
[    1.210841] mtd: device 19 (rootfs) set to be root filesystem
[    1.211078] mtdsplit: no squashfs found in "rootfs"
[    1.215580] 0x000003e80000-0x000007c80000 : "rootfs_1"
[    1.266138] libphy: Fixed MDIO Bus: probed
[    1.486035] qca-mdio 88000.mdio: Could not find phy-reset-gpio
[    1.486229] libphy: qca_mdio: probed
[    1.491442] qca-mdio 88000.mdio: qca-mdio driver was registered
[    1.926047] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[    1.926226] libphy: qca_mdio: probed
[    1.931279] qca-mdio 90000.mdio: qca-mdio driver was registered
[    2.036328] cnss: INFO: IPC Logging is disabled!
[    2.037038] cnss[2]: INFO: Platform driver probed successfully. plat 9df70010 tgt 0xfffc
[    2.040092] Skipping cnss_probe for PCI_0 device 0xfffb
[    2.048565] cnss[42]: INFO: Platform driver probed successfully. plat 9df78010 tgt 0xfffb
[    2.053426] i2c /dev entries driver
[    2.062782] qcom-tsens 4a8000.thermal-sensor: tsens calibration failed
[    2.086794] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    2.087421] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz
[    2.094368] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 800000 KHz
[    2.101607] sdhci: Secure Digital Host Controller Interface driver
[    2.110036] sdhci: Copyright(c) Pierre Ossman
[    2.116012] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.121905] 
[    2.121905] Version Rollback Feature Disabled
[    2.127059] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x08b04000
[    2.131793] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x08b04000
[    2.147691] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x08b04000
[    2.162185] sps:BAM 0x08b04000 is registered.[    2.171586] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss
[    2.172966] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available
[    2.181632] q6v5_wcss_userpd1(9eb86c80) node found
[    2.189255] platform q6v5_wcss_userpd1: ssr registeration success q6v5_wcss_userpd1
[    2.193083] remoteproc remoteproc1: q6v5_wcss_userpd1 is available
[    2.200649] q6v5_wcss_userpd2(9eb86f24) node found
[    2.207858] platform q6v5_wcss_userpd2: ssr registeration success q6v5_wcss_userpd2
[    2.211654] remoteproc remoteproc2: q6v5_wcss_userpd2 is available
[    2.219242] q6v5_wcss_userpd3(9eb87194) node found
[    2.226476] platform q6v5_wcss_userpd3: ssr registeration success q6v5_wcss_userpd3
[    2.230244] remoteproc remoteproc3: q6v5_wcss_userpd3 is available
[    2.238314] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[    2.244083] coresight-csr 6001000.csr: CSR initialized
[    2.251824] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[    2.256744] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[    2.264205] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[    2.271637] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[    2.279004] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[    2.286390] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[    2.293703] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[    2.301121] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[    2.308501] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[    2.315850] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[    2.323260] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[    2.330639] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[    2.338010] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[    2.345357] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[    2.352807] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[    2.360166] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[    2.367526] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[    2.375027] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[    2.382459] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[    2.389916] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06064000
[    2.396851] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06064000
[    2.412536] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06064000
[    2.427027] sps:BAM 0x06064000 is registered.[    2.434199] coresight-tmc 6048000.tmc: TMC initialized
[    2.438391] coresight-tmc 6047000.tmc: TMC initialized
[    2.443486] coresight-funnel 6041000.funnel: FUNNEL initialized
[    2.448503] coresight-funnel 6100000.funnel: FUNNEL initialized
[    2.454253] coresight-funnel 6120000.funnel: FUNNEL initialized
[    2.460228] coresight-funnel 6130000.funnel: FUNNEL initialized
[    2.466138] coresight-funnel 61a1000.funnel: FUNNEL initialized
[    2.472800] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[    2.478380] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[    2.483878] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized
[    2.489681] coresight-stm 6002000.stm: STM initialized
[    2.498641] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[    2.501852] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[    2.514450] NET: Registered protocol family 10
[    2.517950] NET: Registered protocol family 17
[    2.521268] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.525667] Bridge firewalling registered
[    2.538437] 8021q: 802.1Q VLAN Support v1.8
[    2.542625] Registering SWP/SWPB emulation handler
[    2.549138] ubi0: attaching mtd19
[    2.707856] random: nonblocking pool is initialized
[    2.752360] ubi0: scanning is finished
[    2.756694] ubi0: attached mtd19 (name "rootfs", size 62 MiB)
[    2.756718] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.761410] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.768216] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.775038] ubi0: good PEBs: 496, bad PEBs: 0, corrupted PEBs: 0
[    2.781826] ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128
[    2.788073] ubi0: max/mean erase counter: 116/36, WL threshold: 4096, image sequence number: 1560982293
[    2.795093] ubi0: available PEBs: 0, total reserved PEBs: 496, PEBs reserved for bad PEB handling: 20
[    2.804421] ubi0: background thread "ubi_bgt0d" started, PID 111
[    2.818252] hctosys: unable to open rtc device (rtc0)
[    2.827015] ALSA device list:
[    2.827034]   No soundcards found.
[    2.831902] VFS: Mounted root (squashfs filesystem) readonly on device 31:24.
[    2.833724] Freeing unused kernel memory: 1024K (80c00000 - 80d00000)
[    3.242667] init: Console is alive
[    3.242886] init: - watchdog -
[    4.945550] usbcore: registered new interface driver usbfs
[    4.945628] usbcore: registered new interface driver hub
[    4.950088] usbcore: registered new device driver usb
[    4.957905] Button Hotplug driver version 0.4.1
[    4.970548] SCSI subsystem initialized
[    5.003404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.004286] ehci-platform: EHCI generic platform driver
[    5.014020] remoteproc remoteproc4: bt_rproc_driver is available
[    5.014090] bt_rproc: clk_sharing=0
[    5.020326] bt_rproc_driver bt_rproc_driver: Probed
[    5.254820] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.254872] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    5.259499] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
[    5.266860] xhci-hcd xhci-hcd.0.auto: irq 225, io mem 0x08a00000
[    5.276308] hub 1-0:1.0: USB hub found
[    5.281719] hub 1-0:1.0: 1 port detected
[    5.285642] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.289427] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    5.294698] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.302879] hub 2-0:1.0: USB hub found
[    5.310556] hub 2-0:1.0: 1 port detected
[    5.319755] usbcore: registered new interface driver usb-storage
[    5.321093] usbcore: registered new interface driver uas
[    6.266192] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
Before mount_root
[    8.579294] UBIFS (ubi0:4): background thread "ubifs_bgt0_4" started, PID 146
[    8.591280] UBIFS (ubi0:4): recovery needed
[    8.667003] UBIFS (ubi0:4): recovery completed
[    8.667125] UBIFS (ubi0:4): UBIFS: mounted UBI device 0, volume 4, name "rootfs_data"
[    8.670355] UBIFS (ubi0:4): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.678290] UBIFS (ubi0:4): FS size: 19046400 bytes (18 MiB, 150 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs)
[    8.688155] UBIFS (ubi0:4): reserved for root: 899608 bytes (878 KiB)
[    8.698392] UBIFS (ubi0:4): media format: w4/r0 (latest is w4/r0), UUID 21DDE13C-0B67-445E-9125-A10270BB1797, small LPT model
[    8.709167] mount_root: switching to jffs2 overlay
After mount_root
131072+0 records in
131072+0 records out
131072 bytes (128.0KB) copied, 0.603296 seconds, 212.2KB/s
ln: /lib/firmware/IPQ5018/caldata.bin: File exists
131072+0 records in
131072+0 records out
131072 bytes (128.0KB) copied, 0.576460 seconds, 222.0KB/s
ln: /lib/firmware/qcn9100/caldata_2.bin: No such file or directory
ln: /lib/firmware/qcn6122/caldata_2.bin: File exists
131072+0 records in
131072+0 records out
131072 bytes (128.0KB) copied, 0.554105 seconds, 231.0KB/s
ln: /lib/firmware/qcn9100/caldata_1.bin: No such file or directory
ln: /lib/firmware/qcn6122/caldata_1.bin: File exists
[   10.567434] procd: - early -
[   10.567542] procd: - watchdog -
[   11.246274] procd: - ubus -
[   12.258599] procd: - init -
Please press Enter to activate this console.
[   13.106892] ubi: mtd19 is already attached to ubi0BT FW mount is successful

[   13.283949] ubi: mtd19 is already attached to ubi0 WIFI FW mount is successful
[   15.733323] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   15.743323] Initializing XFRM netlink socket
[   15.745147] NET: Registered protocol family 15
[   17.215864] ssdk_switch_device_num_init[1159]:INFO:ess-switch dts node number: 1
[   17.215906] ssdk_dt_get_switch_node[970]:INFO:ess-switch DT exist!
[   17.222359] ssdk_dt_parse_access_mode[856]:INFO:switch_access_mode: local bus
[   17.228327] ssdk_dt_parse_access_mode[869]:INFO:switchreg_base_addr: 0x39c00000
[   17.235514] ssdk_dt_parse_access_mode[870]:INFO:switchreg_size: 0x200000
[   17.242644] ssdk_dt_parse_mac_mode[295]:INFO:mac mode = 0xf
[   17.249586] ssdk_dt_parse_mac_mode[301]:INFO:mac mode1 doesn't exit!
[   17.254871] ssdk_dt_parse_mac_mode[310]:INFO:mac mode2 doesn't exit!
[   17.261524] ssdk_dt_parse_phy_info[659]:INFO:[PORT 2] port_mac_sel = QGMAC_PORT
[   17.267858] ssdk_dt_parse_phy_info[678]:INFO:port2's phy-reset-gpio is GPIO26
[   17.274840] ssdk_dt_parse_port_bmp[757]:INFO:port_bmp doesn't exist!
[   17.282165] ssdk_dt_parse_uniphy[332]:INFO:ess-uniphy DT exist!
[   17.288573] ssdk_dt_parse_led[943]:INFO:current dts led_source_num is 1
[   17.294209] ssdk_plat_init start
[   19.706015] ssdk_mp_reset_init[739]:INFO:MP reset successfully!
[   19.706079] ssdk_gcc_clock_init[1033]:INFO:SSDK gcc clock init successfully!
[   19.712205] mpge_phy_api_ops_init[1089]:INFO:qca probe mpge phy driver succeeded!
[   19.718482] qca808x_phy_api_ops_init[2208]:INFO:qca probe qca808x phy driver succeeded!
[   19.729717] regi_init[3598]:INFO:Initializing SCOMPHY!
[   21.065996] hsl_port_phy_gpio_reset[685]:INFO:GPIO26 reset PHY done
[   21.176630] ssdk_led_init[152]:INFO:ssdk_led_mode:3, ssdk_led_map:ffc, ssdk_led_src_id:0
[   21.176752] ssdk_switch_register[1710]:INFO:Chip version 0xee
[   21.183792] qca_link_polling_select[1315]:INFO:link-polling-required node does not exist
[   21.189443] ssdk_switch_register[1744]:INFO:polling is selected
[   21.197586] regi_init[3608]:INFO:Initializing SCOMPHY Done!!
[   21.203384] regi_init[3631]:INFO:qca-ssdk module init succeeded!
[   21.227783] tun: Universal TUN/TAP device driver, 1.6
[   21.227809] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   21.450849] **********************************************************
[   21.450883] * NSS Data Plane driver
[   21.456322] **********************************************************
[   21.488919] l2tp_core: L2TP core driver, V2.0
[   21.490519] l2tp_netlink: L2TP netlink interface
[   21.814087] nss_driver - fw of size 761676  bytes copied to load addr: 40000000, nss_id : 0
[   21.815512] Supported Frequencies - 
[   21.821279] 850 MHz 1 GHz 
[   21.826891] 
[   21.827805] 7f752480: set sdma 9d737600
[   21.829541] node size 2 # items 4
[   21.832780] memory: 40000000 536870912 (avl 432435200) items 4 active_cores 1
[   21.836298] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000
[   21.843374] 7f752480: NSS core 0 DDR from 40000000 to 41000000
[   21.850244] 7f752480: meminfo init succeed
[   21.859681] sit: IPv6 over IPv4 tunneling driver
[   21.867178] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[   21.872520] gre: GRE over IPv4 demultiplexor driver
[   21.876536] ip_gre: GRE over IPv4 tunneling driver
[   21.884474] ip6_gre: GRE over IPv6 tunneling driver
[   21.891367] node size 2 # items 4
[   21.891399] memory: 40000000 536870912 (avl 432435200) items 4 active_cores 1
[   21.893684] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000
[   21.900859] 7f752480: nss core 0 booted successfully
[   21.936294] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   21.967487] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   21.978274] rmnet_nss_init(): initializing rmnet_nss
[   21.993293] nf_conntrack version 0.5.0 (6239 buckets, 24956 max)
[   22.002996] openvswitch: Open vSwitch switching datapath
[   22.029879] PPP generic driver version 2.4.2
[   22.067578] nss_lag_init[352]:LAG Manager Installed
[   22.071078] NET: Registered protocol family 24
[   22.080884] PPTP driver version 0.8.5
[   22.106887] diag: IPC Logging disabled
[   22.113658] TRACK: P[0]	PMask[4]
[   22.113679] TRACK: P[1]	PMask[4]
[   22.116132] TRACK: P[2]	PMask[4]
[   22.136697] TRACK: P[3]	PMask[4]
[   22.136782] nik 4097 info->svc_id
[   22.199884] QCA multicast snooping installed successfully
[   22.203140] <NSS-CRYPTO>:module loaded Build_ID - 07/29/24, 04:29:03 SoC=ipq50xx
[   22.218108] cannot find nss-macsec0 node
[   22.218233] cannot find nss-macsec1 node
[   22.221291] cannot find nss-macsec2 node
[   22.225084] nss_macsec init success
[   22.278661] hidraw: raw HID events driver (C) Jiri Kosina
[   22.290992] u32 classifier
[   22.291016]     input device check on
[   22.292583]     Actions configured
[   22.299677] Mirror/redirect action on
[   22.342233] fuse init (API version 7.23)
[   22.349575] arp_tables: (C) 2002 David S. Miller
[   22.411220] Bluetooth: Core ver 2.21
[   22.411388] NET: Registered protocol family 31
[   22.413948] Bluetooth: HCI device and connection manager initialized
[   22.422592] Bluetooth: HCI socket layer initialized
[   22.424703] Bluetooth: L2CAP socket layer initialized
[   22.429491] Bluetooth: SCO socket layer initialized
[   22.436214] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   22.439179] Bluetooth: BNEP filters: protocol multicast
[   22.444734] Bluetooth: BNEP socket layer initialized
[   22.460032] usbcore: registered new interface driver btusb
[   22.462091] Bluetooth: HCI UART driver ver 2.3
[   22.464467] Bluetooth: HCI UART protocol H4 registered
[   22.469079] Bluetooth: HCI UART protocol BCSP registered
[   22.474002] Bluetooth: HCI UART protocol ATH3K registered
[   22.482908] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   22.484806] Bluetooth: HIDP socket layer initialized
[   22.499156] ip_tables: (C) 2000-2006 Netfilter Core Team
[   22.509820] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   22.591542] nf_conntrack_rtsp v0.6.21
3 
[   22.695745] nf_nat_rtsp v0.6.21 loading
[   22.704660] PPP MPPE Compression module registered
[   22.708124] Bluetooth: RFCOMM TTY layer initialized
[   22.708353] Bluetooth: RFCOMM socket layer initialized
[   22.713179] Bluetooth: RFCOMM ver 1.11
[   22.770186] xt_time: kernel timezone is -0000
acfg_tool: Issuing blocking call to wait for events
[   26.517495] vmap allocation for size 1155072 failed: use vmalloc=<size> to increase size.
[   26.518297] vmap allocation for size 86016 failed: use vmalloc=<size> to increase size.
[   26.604301] ECM init
[   26.604375] ECM database jhash random seed: 0x73c6ab9b
[   26.676058] ECM init complete
[   26.697542] ECM OVS Test INIT
qcawifi qcawificfg80211 disable radio wifi0
qcawifi qcawificfg80211 disable radio wifi1
qcawifi qcawificfg80211: enable radio wifi0
[   30.475563] configuring additional NSS pbufs
[   30.518298] additional pbufs of size 3100672 got added to NSS
[   30.678212] mem_manager: module license 'Proprietary' taints kernel.
[   30.678245] Disabling lock debugging due to kernel taint
[   30.719613] vmap allocation for size 503808 failed: use vmalloc=<size> to increase size.
[   30.720043] vmap allocation for size 65536 failed: use vmalloc=<size> to increase size.
[   31.983121] sh (1935): drop_caches: 3
**** Platform Name: ap-mp03.5-c1 *****
Copy ART caldata from /dev/mtdblock13 to /tmp/virtual_art.bin
[   35.345759] ECM OVS Test EXIT
[   37.285329] vmap allocation for size 3092480 failed: use vmalloc=<size> to increase size.
[   37.287663] vmap allocation for size 475136 failed: use vmalloc=<size> to increase size.
[   37.534408] wlan: [1872:I:RPTR] qca_multi_link_init_module: 
[   37.534408] ******QCA Repeater Initialization Done***********
[   37.534408] 
[   37.582176] vmap allocation for size 114688 failed: use vmalloc=<size> to increase size.
***** starting cnssdaemon  -i integrated -i integrated1 -i integrated2 *****
*****cnssdaemon pid=2114*********
[   38.972379] cnss: ERR: Failed to get plat_priv for instance_id 0x41
[   39.001196] cnss[42]: INFO: Setting daemon_support=1 for instance_id 0x42
[   39.027538] cnss[2]: INFO: Setting daemon_support=1 for instance_id 0x2
******No cold_boot_support*****
[   40.254757] vmap allocation for size 1507328 failed: use vmalloc=<size> to increase size.
[   40.255781] vmap allocation for size 270336 failed: use vmalloc=<size> to increase size.
[   40.452522] ECM exit
[   40.696448] ECM exit complete
[   41.187674] vmap allocation for size 1040384 failed: use vmalloc=<size> to increase size.
[   41.188415] vmap allocation for size 151552 failed: use vmalloc=<size> to increase size.
[   41.209319] wlan: [2195:I:ANY] =======ol_if_register_wifi3_0==========
[   41.209319] 
[   41.209365] wlan: [2195:I:ANY] osif_nss_register_module: NSS wifi ops registered for target_type:1 with soc_ops:a5c63e10
[   41.216239] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss
[   41.251901] remoteproc remoteproc0: Booting fw image IPQ5018/q6_fw.mdt, size 1820
[   41.847342] FPP - Proc Module Load ...
[   41.855650] FPPOS - Debug Module Load ...
[   41.881281] FPPOS - Tree Module Load ...
[   41.890967] FPPOS - Vsys Module Load ...
[   41.899132] vmap allocation for size 622592 failed: use vmalloc=<size> to increase size.
[   41.913815] vmap allocation for size 323584 failed: use vmalloc=<size> to increase size.
[   41.929463] start probe thread successful
[   41.929540] FPPOS - Main Module Load ...
[   41.941272] FPPOS - Vslan Config Module Load ...
[   41.964481] vmap allocation for size 294912 failed: use vmalloc=<size> to increase size.
[   41.979644] FPPOS - Client Module Load ...
[   41.988738] FPPOS - Qos Module Load ...
[   42.001192] FPPOS - ARP Module Load ...
[   42.010860] FPPOS - Defragment Module Load ...
[   42.032454] FPPOS - Admin Module load ...
[   42.050469] FPPOS - Resource Module Load ...
[   42.059051] FPPOS - MMS Module Load ...
[   42.074592] FPPOS - Rule Module Load ...
[   42.098658] FPPOS - State Module Load ...
[   42.108463] FPPOS - NAT Module Load ...
[   42.127238] FPPOS - IPV4 Module Load ...
[   42.144974] FPPOS - Dynamic Protocol Module Load ...
[   42.153054] FPPOS - Dynamic FTP Protocol Module Load ...
[   42.171121] FPPOS - Dynamic TFTP Protocol Module Load ...
[   42.184989] FPPOS dynamic PPTP module loaded
[   42.197528] FPPOS dynamic SIP module loaded
[   42.210378] FPPOS dynamic SQLNET module loaded
[   42.219223] FPPOS - IPV6 Module Load ...
[   42.235370] FPPOS - Client_Redirect6 Module Unload ...
[   42.255893] fpp_gre: exports duplicate symbol gretap_fb_dev_create (owned by ip_gre)
[   42.410900] alloc_vmap_area: 13 callbacks suppressed
[   42.410928] vmap allocation for size 24576 failed: use vmalloc=<size> to increase size.
[   42.416424] FPPOS - 802.1xclient Module init success
[   42.430202] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[   42.431240] FPPOS - anti_attack Module init success
[   42.463421] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[   42.464019] drvmsg: Unknown symbol probe_rogue_ap_config (err 0)
[   42.474053] drvmsg: Unknown symbol probe_ssid_handle (err 0)
[   42.559350] vmap allocation for size 24576 failed: use vmalloc=<size> to increase size.
[   42.713402] vmap allocation for size 45056 failed: use vmalloc=<size> to increase size.
[   42.715395] vslan_core: exports duplicate symbol l2tp_recv_common (owned by l2tp_core)
[   42.882780] vslan_netlink: Unknown symbol l2tp_tunnel_list_find (err 0)
[   42.884794] vslan_netlink: Unknown symbol l2tp_session_update (err 0)
[   42.955355] vslan_eth: L2TP ethernet pseudowire support (L2TPv3)
[   42.972478] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[   42.973165] vslan_send: Unknown symbol l2tp_pernet (err 0)
[   43.128056] mc_attach: enabled snooping on br-wan.
[   43.140471] device eth0 entered promiscuous mode
[   43.174069] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   43.182776] Subsystem error monitoring/handling services are up
[   43.183330] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up
[   43.183695] rpmsg_dev_probe: No pm domain
[   43.184257] rpmsg_dev_probe: No pm domain
[   43.187418] diag: Receiving feature mask length more than Apps support
[   43.187444] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, 7f9c1d84
[   43.211918] br-wan: port 1(eth0) entered forwarding state
[   43.218611] br-wan: port 1(eth0) entered forwarding state
[   43.225122] wlan: [2195:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 2 bus_type 1
[   43.233601] remoteproc remoteproc1: powering up q6v5_wcss_userpd1
[   43.254169] q6v5_wcss_userpd1 wcss powered up successfully
[   43.256354] Subsystem error monitoring/handling services are up
[   43.262301] remoteproc remoteproc1: remote processor q6v5_wcss_userpd1 is now up
[   43.264541] wlan: [2195:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 3 bus_type 1
[   43.273137] cnss[2]: INFO: Waiting for FW ready. Device: 0xfffc, FW ready timeout: 15 seconds
[   43.280199] cnss[2]: INFO: QMI WLFW service connected, state: 0x1
[   43.300737] cnss[2]: INFO: device_id : 65532 mem mode : [1]
[   43.300779] cnss[2]: INFO: platform name: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.5-C1
[   43.314929] mc_attach: enabled snooping on br-lan.
[   43.317224] cnss[2]: INFO: Target capability: chip_id: 0x0, chip_family: 0x4, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x250dffff, fw_build_timestamp: 2021-10-27 11:42, otp_version: 0x0 eeprom_caldata_read_timeout 0s
[   43.318848] cnss[2]: INFO: Using Boardid from bootargs:0x24
[   43.354363] cnss[2]: INFO: BDF location : 0x4c400000
[   43.354401] cnss[2]: INFO: BDF IPQ5018/bdwlan.b24 size 131072
[   43.360500] cnss[2]: INFO: per device BDF location : 0x4c420000
[   43.364205] cnss[2]: INFO: CALDATA IPQ5018/caldata.bin size 131072 offset 0x20000
[   43.386098] cnss[2]: INFO: FW ready received for device 0xfffc
[   43.386523] wlan: [2195:I:ANY] pld_ahb_wlan_enable: cnss_mode: Mission mode 
[   43.391161] cnss[2]: INFO: Sending mode message, mode: MISSION(0), state: 0x7
[   43.409924] wlan: [2195:I:ANY] qca_napi_create: qca_napi_create: napi instance 0 created on pipe 4
[   43.410321] wlan: [2195:I:ANY] __ol_ath_attach: Allocated soc 97dc0500
[   43.425321] wlan: [2195:D:dfs] WLAN_DEBUG_DFS1 : dfs_psoc_obj_create_notification: DFS obj attach to psoc successfully
[   43.512479] wlan: [2195:E:CONFIG] cfg_ini_parse_to_store: Failed to parse *.ini file @ QCA5018.ini; status:4
[   43.526431] wlan: [2195:I:ANY] osif_nss_wifi_soc_setup: nss-wifili:#1 register wifili function for soc 
[   43.526476] wlan: [2195:I:ANY] osif_nss_wifi_soc_setup: nss register id -1 nss config 3 Target Type 1d 
[   43.534690] wlan: [2195:I:ANY] __ol_ath_attach: dev name soc0
[   43.544871] wlan: [2195:I:ANY] ol_ath_soc_attach: WMI attached. wmi_handle 9916dc00 
[   43.559149] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.559215] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.568810] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.578428] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.588812] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.599250] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.608973] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   43.618614] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   43.628665] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   43.638753] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   43.648848] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.658880] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.668935] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   43.679004] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   43.689107] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   43.699187] wlan: [2195:I:ANY] htc_wmi_init: HT Create . 97d99000
[   43.709213] wlan: [2195:I:ANY] htc_wmi_init: Skipping BMI Done
[   43.715333] wlan: [2195:I:ANY] htc_wmi_init: host_enable 0
[   43.732079] wlan: [2195:I:ANY] ol_target_init_complete: CDP soc attach success
[   43.732129] wlan: [2195:I:ANY] ol_target_init_complete: Soc attach success NSS config 0 
[   43.738626] wlan: [2195:I:ANY] htc_set_async_ep: htc_set_async_ep: htc_handle 97d99000, ep 2, value 1
[   43.756266] wlan: [950:I:TIF] HE_CAP Info = 9a08010d
[   43.756301] wlan: [950:I:TIF] Num HW modes = 1
[   43.760593] wlan: [950:I:TIF] Num PHY = 1
[   43.764844] wlan: [950:I:TIF] FW Build Version (Ext.) = 0
[   43.769272] wlan: [950:I:TIF] HDL Version: MajorVersion.MinorVersion = 0.0
[   43.774319] wlan: [950:I:TIF] Preferred HW Mode = 0 Num Radios = 1
[   43.781418] wlan: [950:W:TIF] add_11ax_mode_flags: 11AX wireless modes are not populated by the target in reg capabilities, adding 11AX wireless modes
[   43.787457] wlan: [950:I:TIF] init_deinit_add_11ax_modes: hw_mode_id = 0 phy_id = 0 wireless modes = 0
[   43.801950] wlan: [950:I:TIF] init_deinit_alloc_pdevs: CDP PDEV ATTACH success
[   43.810305] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   43.817473] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   43.824419] wlan: [950:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 10
[   43.832599] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   43.840272] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   43.847409] wlan: [950:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 10
[   43.855235] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   43.863085] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   43.870043] wlan: [950:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 10
[   43.878024] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   43.885598] wlan: [950:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   43.892959] wlan: [950:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 10
[   43.900895] wlan: [950:I:ANY] init_deinit_update_pdev_tgt_info: pdev id:0 wmi_handle:9916dc00
[   43.919628] wlan: [950:I:ANY] init_deinit_update_pdev_tgt_info: Pdev = 0 Number of peers = 138 vdevs = 10
[   43.919678] wlan: [950:I:TIF] init_deinit_update_pdev_tgt_info: CDP PDEV INIT success
[   44.044649] wlan: [950:I:ANY] copy_fw_abi_version_tlv: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[   44.084816] wlan: [950:I:ANY] ready_extract_init_status_tlv: ready_extract_init_status_tlv:0
[   44.084863] wlan: [950:I:ANY] dp_peer_map_attach_wifi3: dp_peer_map_attach_wifi3 max_peers 165, max_ast_index: 528
[   44.084863] 
[   44.092742] wlan: [2195:I:ANY] ol_ath_connect_htc: WMI is ready
[   44.134868] wlan: [2195:I:ANY] ath_get_radio_index: Error: Could not match the device name : wifi%d
[   44.134918] wlan: [2195:E:NSS] [nss-wifili]: pdev:959e0500 radio_ifnum:28 scheme_id:1 radio_priority:0 
[   44.143088] br-wan: port 1(eth0) entered disabled state
[   44.159990] wlan: [2195:E:TIF] target_if_lro_hash_config: pdev with id 0 is NULL
[   44.160504] wlan: [2195:I:ANY] ol_ath_soc_attach: connect HTC
[   44.166816] wlan: [2195:I:ANY] ol_ath_soc_attach: bypasswmi : 0
[   44.172175] wlan: [2195:I:MSCS] qca_mscs_module_init: 
[   44.172175] ****QCA MSCS Initialization Done**** SoC 97dc0500
[   44.181857] wlan: [2195:I:ANY] ol_ath_soc_attach: UMAC attach
[   44.189177] wlan: [2195:I:ANY] __ol_ath_attach: pdev_netdev name wifi0
[   44.194602] wlan: [2195:I:ANY] __ol_ath_attach: Skip txrx_pdev_attach_target
[   44.202284] wlan: [2195:I:ANY] __ol_ath_attach: BURSTING enabled by default
[   44.208462] wlan: [2195:I:ANY] ol_ath_pdev_attach: interface_id 0
[   44.214909] wlan: [2195:I:TIF] ol_ath_pdev_regdmn_init:  phy id = 0 Modes supported
[   44.221198] wlan: [2195:I:TIF] ol_ath_pdev_regdmn_init:  11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1
[   44.228663] wlan: [2195:I:TIF] ol_ath_pdev_regdmn_init:  Reg cap - phy_id = 0 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0
[   44.238376] wlan: [2195:I:ANY] ol_ath_update_wireless_modes: wireless_modes = 680680c before update
[   44.252558] wlan: [2195:I:ANY] ol_ath_update_wireless_modes: Wireless_modes = 680680c after update
[   44.261312] wlan: [2195:I:ANY] ol_ath_update_ext_caps: 11ax 2G supported case
[   44.270452] wlan: [2195:I:MBSSIE] ol_ath_assign_mbssid_ref_bssid: MBSSID reference bssid is ea:c7:4f:28:e0:80 soc: soc0 pdev: wifi0
[   44.277773] wlan: [2195:I:MBSSIE] ieee80211_mbss_attach: :>
[   44.289164] wlan: [2195:I:MBSSIE] ieee80211_mbss_attach: :<
[   44.294672] wlan: [2195:I:ANY] ol_resmgr_create: OL Resmgr Init-ed
[   44.300688] wlan: [2195:I:ANY] acfg_attach: acfg_attach: 3323: Netlink socket created:967ab800
[   44.306651] wlan: [2195:I:ANY] ol_ath_stats_attach: periodic_chan_stats: 1
[   44.315536] wlan: [2195:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[   44.322074] wlan: [0:I:ANY] ol_ath_pdev_attach: Set global_ic[1], ptr:a6c693a8
[   44.328827] wlan: [0:I:ANY] dp_lag_soc_enable: pdev(967aa408) Enabling DBDC Repeater 0  soc_lag 99e7f000
[   44.336070] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: pdev(967aa408) is_primary 0 
[   44.336169] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[   44.353677] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: twt enabled
[   44.356469] wlan: [2195:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5
[   44.356469] 
[   44.356645] wlan: [2195:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: cfg block channel list is empty
[   44.356670] wlan: [2195:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: pdev_idx = 0 tx_desc_limit = 32768
[   44.356753] wlan: [2195:I:ANY] __ol_ath_attach: needed_headroom reservation 60
[   44.356768] wlan: [2195:I:ANY] ol_ath_enable_fraglist: Enabled Fraglist bit for the radio wifi0 features 41 
[   44.356803] wlan: [2195:I:ANY] wlan_cfg80211_init: Number of 2G channels: 11 
[   44.357130] wlan: [2195:I:ANY] ieee80211_cfg80211_radio_attach: ic: 0x959e0500, wdev: 0x959f7c6c, wiphy: 0x95767160, netdev: 0x959e0000 
[   44.358428] wlan: [2195:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: Running with HW mode = 0
[   44.359194] wlan: [2195:E:QLD] qld_register: Handle or address is NULL
[   44.359325] wlan: [2195:I:ANY] wlan_pdev_operation: num_radios=1, wifi_radios[0].sc = 959e0500_radio_type = 2
[   44.359396] wlan: [2195:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 2 bus_type 1
[   44.359423] remoteproc remoteproc3: powering up q6v5_wcss_userpd3
[   44.369181] Subsystem error monitoring/handling services are up
[   44.369281] remoteproc remoteproc3: remote processor q6v5_wcss_userpd3 is now up
[   44.369343] wlan: [2195:I:ANY] ol_ath_wifi_ssr: ol_ath_wifi_ssr: SSR event 3 bus_type 1
[   44.369367] cnss[42]: INFO: Waiting for FW ready. Device: 0xfffb, FW ready timeout: 15 seconds
[   44.466906] cnss[42]: INFO: QMI WLFW service connected, state: 0x1
[   44.494246] cnss[42]: INFO: device_id : 65531 mem mode : [1]
[   44.518751] cnss[42]: INFO: platform name: Qualcomm Technologies, Inc. IPQ5018/AP-MP03.5-C1
[   44.518752] cnss[42]: INFO: Target capability: chip_id: 0x0, chip_family: 0x4, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x250dffff, fw_build_timestamp: 2021-10-27 11:42, otp_version: 0x0 eeprom_caldata_read_timeout 0s
[   44.530931] cnss[42]: INFO: Device BAR Info pa: 0xa1e00000, va: 0xa8a80000, size: 0x200000
[   44.551074] cnss[42]: INFO: Using Boardid from bootargs:0x60
[   44.568263] cnss[42]: INFO: BDF location : 0x4ed00000
[   44.568292] cnss[42]: INFO: BDF qcn6122/bdwlan.b60 size 131072
[   44.573479] cnss[42]: INFO: per device BDF location : 0x4ed20000
[   44.578307] cnss[42]: INFO: CALDATA qcn6122/caldata_2.bin size 131072 offset 0x20000
[   44.696007] cnss[42]: INFO: FW ready received for device 0xfffb
[   44.696236] wlan: [2195:I:ANY] pld_ahb_wlan_enable: cnss_mode: Mission mode 
[   44.701082] cnss[42]: INFO: Sending mode message, mode: MISSION(0), state: 0x7
[   44.718497] wlan: [2195:I:ANY] qca_napi_create: qca_napi_create: napi instance 0 created on pipe 4
[   44.718831] wlan: [2195:I:ANY] __ol_ath_attach: Allocated soc 93540500
[   44.726577] wlan: [2195:D:dfs] WLAN_DEBUG_DFS1 : dfs_psoc_obj_create_notification: DFS obj attach to psoc successfully
[   44.788614] wlan: [2195:E:QDF] CONFIG creation failed
[   44.788725] wlan: [2195:I:ANY] osif_nss_wifi_soc_setup: nss-wifili:#1 register wifili function for soc 
[   44.792658] wlan: [2195:I:ANY] osif_nss_wifi_soc_setup: nss register id -1 nss config 3 Target Type 1e 
[   44.801969] wlan: [2195:I:ANY] __ol_ath_attach: dev name soc1
[   44.811618] wlan: [2195:I:ANY] ol_ath_soc_attach: WMI attached. wmi_handle 9342a800 
[   44.820847] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.824947] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.834831] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.844859] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.854997] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.865002] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.875071] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   44.885133] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   44.895200] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   44.905270] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   44.915337] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.925406] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.935480] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 1
[   44.945544] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   44.955616] wlan: [2195:I:MBSSIE] ol_ath_sanitize_ema_vendor_ie_config: vendor_ie_size: 0 ven_ie_size_nibble: 7
[   44.965748] wlan: [2195:I:ANY] htc_wmi_init: HT Create . 93582000
[   44.975769] wlan: [2195:I:ANY] htc_wmi_init: Skipping BMI Done
[   44.982425] wlan: [2195:I:ANY] htc_wmi_init: host_enable 0
[   44.997572] wlan: [2195:I:ANY] ol_target_init_complete: CDP soc attach success
[   44.997618] wlan: [2195:I:ANY] ol_target_init_complete: Soc attach success NSS config 0 
[   45.003890] wlan: [2195:I:ANY] htc_set_async_ep: htc_set_async_ep: htc_handle 93582000, ep 2, value 1
[   45.013145] wlan: [965:I:TIF] HE_CAP Info = 9a08010d
[   45.021156] wlan: [965:I:TIF] Num HW modes = 1
[   45.026127] wlan: [965:I:TIF] Num PHY = 1
[   45.030338] wlan: [965:I:TIF] FW Build Version (Ext.) = 0
[   45.034418] wlan: [965:I:TIF] HDL Version: MajorVersion.MinorVersion = 0.0
[   45.039831] wlan: [965:I:TIF] Preferred HW Mode = 0 Num Radios = 1
[   45.046663] wlan: [965:W:TIF] add_11ax_mode_flags: 11AX wireless modes are not populated by the target in reg capabilities, adding 11AX wireless modes
[   45.052749] wlan: [965:I:TIF] init_deinit_add_11ax_modes: hw_mode_id = 0 phy_id = 0 wireless modes = 0
[   45.067444] wlan: [965:I:TIF] init_deinit_alloc_pdevs: CDP PDEV ATTACH success
[   45.075489] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   45.082749] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   45.090006] wlan: [965:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 17
[   45.098303] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   45.105604] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   45.112706] wlan: [965:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 17
[   45.120743] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   45.128397] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   45.135381] wlan: [965:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 17
[   45.143453] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: num_radios: 1
[   45.151129] wlan: [965:I:TIF] init_deinit_get_total_num_ema_vaps: ema_max_vap_cnt: 0
[   45.158153] wlan: [965:I:TIF] init_deinit_get_total_num_vdevs_for_soc: num_vdevs: 17
[   45.166139] wlan: [965:I:ANY] init_deinit_update_pdev_tgt_info: pdev id:0 wmi_handle:9342a800
[   45.180559] wlan: [965:I:ANY] init_deinit_update_pdev_tgt_info: Pdev = 0 Number of peers = 529 vdevs = 17
[   45.182259] wlan: [965:I:TIF] init_deinit_update_pdev_tgt_info: CDP PDEV INIT success
[   45.292701] wlan: [965:I:ANY] copy_fw_abi_version_tlv: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[   45.482503] wlan: [965:I:ANY] ready_extract_init_status_tlv: ready_extract_init_status_tlv:0
[   45.482549] wlan: [965:E:TIF] init_deinit_ready_event_handler: Host Requested 529 peers. FW Supports 160 peers
[   45.490073] wlan: [965:I:ANY] dp_peer_map_attach_wifi3: dp_peer_map_attach_wifi3 max_peers 194, max_ast_index: 528
[   45.490073] 
[   45.500021] wlan: [2195:I:ANY] ol_ath_connect_htc: WMI is ready
[   45.542586] wlan: [2195:I:ANY] ath_get_radio_index: Error: Could not match the device name : wifi%d
[   45.542635] wlan: [2195:E:NSS] [nss-wifili]: pdev:92fc0500 radio_ifnum:29 scheme_id:2 radio_priority:0 
[   45.556912] wlan: [2195:E:TIF] target_if_lro_hash_config: pdev with id 0 is NULL
[   45.560276] wlan: [2195:I:ANY] ol_ath_soc_attach: connect HTC
[   45.567589] wlan: [2195:I:ANY] ol_ath_soc_attach: bypasswmi : 0
[   45.573133] wlan: [2195:I:ANY] ol_ath_soc_attach: UMAC attach
[   45.579088] wlan: [2195:I:ANY] __ol_ath_attach: pdev_netdev name wifi1
[   45.584753] wlan: [2195:I:ANY] __ol_ath_attach: Skip txrx_pdev_attach_target
[   45.592446] wlan: [2195:I:ANY] __ol_ath_attach: BURSTING enabled by default
[   45.598648] wlan: [2195:I:ANY] ol_ath_pdev_attach: interface_id 1
[   45.605055] wlan: [2195:I:TIF] ol_ath_pdev_regdmn_init:  phy id = 0 Modes supported
[   45.611507] wlan: [2195:I:TIF] ol_ath_pdev_regdmn_init:  11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1
[   45.618836] wlan: [2195:I:TIF] ol_ath_pdev_regdmn_init:  Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 5150, hi_5g = 5895
[   45.628525] wlan: [2195:I:ANY] ol_ath_update_wireless_modes: wireless_modes = f97f9001 before update
[   45.642761] wlan: [2195:I:ANY] ol_ath_update_wireless_modes: Wireless_modes = f97f9001 after update
[   45.651877] wlan: [2195:I:ANY] ol_ath_update_ext_caps: 11ax 5G supported case
[   45.660787] wlan: [2195:I:MBSSIE] ol_ath_assign_mbssid_ref_bssid: MBSSID reference bssid is ea:c7:4f:28:e0:90 soc: soc1 pdev: wifi1
[   45.668149] wlan: [2195:I:MBSSIE] ieee80211_mbss_attach: :>
[   45.679575] wlan: [2195:I:MBSSIE] ieee80211_mbss_attach: :<
[   45.685077] wlan: [2195:I:ANY] ol_resmgr_create: OL Resmgr Init-ed
[   45.690992] wlan: [2195:I:ANY] acfg_attach: acfg_attach: Offload using existing sock 967ab800
[   45.696930] wlan: [2195:I:ANY] acfg_attach: Offload using existing sock 967ab800
[   45.696930] 
[   45.705491] wlan: [2195:I:ANY] ol_ath_stats_attach: periodic_chan_stats: 1
[   45.716429] wlan: [2195:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   45.721231] wlan: [0:I:ANY] ol_ath_pdev_attach: Set global_ic[2], ptr:a6c693a8
[   45.728012] wlan: [0:I:ANY] dp_lag_soc_enable: pdev(9280cc08) Enabling DBDC Repeater 0  soc_lag 9353b440
[   45.735230] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: pdev(9280cc08) is_primary 0 
[   45.735233] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[   45.752885] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: twt enabled
[   45.759116] wlan: [2195:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5
[   45.759116] 
[   45.759294] wlan: [2195:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: cfg block channel list is empty
[   45.759323] wlan: [2195:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: pdev_idx = 0 tx_desc_limit = 32768
[   45.759400] wlan: [2195:I:ANY] __ol_ath_attach: needed_headroom reservation 60
[   45.759414] wlan: [2195:I:ANY] ol_ath_enable_fraglist: Enabled Fraglist bit for the radio wifi1 features 41 
[   45.760031] wlan: [2195:I:ANY] ieee80211_cfg80211_radio_attach: ic: 0x92fc0500, wdev: 0x92fd7c6c, wiphy: 0x92543960, netdev: 0x92fc0000 
[   45.762832] wlan: [2195:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: Running with HW mode = 0
[   45.764265] wlan: [2195:E:QLD] qld_register: Handle or address is NULL
[   45.764338] wlan: [2195:I:ANY] wlan_pdev_operation: num_radios=2, wifi_radios[1].sc = 92fc0500_radio_type = 2
[   45.764400] wlan: [2195:I:ANY] init_ath_pci_3_0: 6ath_ol_pci_wifi3.0 :  (Atheros/multi-bss)
[   46.067072] vmap allocation for size 573440 failed: use vmalloc=<size> to increase size.
[   46.067546] vmap allocation for size 102400 failed: use vmalloc=<size> to increase size.
[   46.102051] wlan: [2413:I:ANY] osif_nss_register_module: NSS wifi ops registered for target_type:0 with soc_ops:a5cf20c4
[   46.102719] wlan: [2413:I:ANY] init_ath_pci_2_0: 6ath_ol_pci_2_0:  (Atheros/multi-bss)
[   46.140067] vmap allocation for size 24576 failed: use vmalloc=<size> to increase size.
[   46.185413] vmap allocation for size 53248 failed: use vmalloc=<size> to increase size.
No Direct-Attach chipsets found.
[   47.680399] wlan: [2852:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[   47.680529] wlan: [2852:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   47.686286] wlan: [2852:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0
[   47.698989] wlan: [2852:I:ANY] wlan_cfg80211_set_country: wlan_cfg80211_set_country: Country: US ret: 0 
[   47.987185] wlan: [2871:I:ANY] wlan_cfg80211_set_hwaddr: wlan_cfg80211_set_hwaddr :e8:c7:4f:28:e0:80 ret: 0 
[   48.031608] wlan: [2874:I:ANY] ol_ath_set_config_param: set TXBF_SND_PERIOD: val 100 stat 0
[   48.164768] wlan: [0:I:ANY] ol_ath_set_config_param: Disconnect_timeout value: 10
[   48.208226] wlan: [0:I:ANY] ol_ath_set_config_param: Reconfiguration_timeout value:60
number of vifs: 
qcawifi qcawificfg80211: enable radio wifi1
4 
[   50.619131] wlan: [3477:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   50.619700] wlan: [3477:E:ANY] dfs_init_chan_state_array: channel state array initialized
[   50.628602] wlan: [3477:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   50.633558] wlan: [3477:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   50.640458] wlan: [3477:I:ANY] number of channels: 2G = 0 5G = 25, 6G = 0
[   50.653074] wlan: [3477:I:ANY] wlan_cfg80211_set_country: wlan_cfg80211_set_country: Country: US ret: 0 
[   50.958227] wlan: [3512:I:ANY] wlan_cfg80211_set_hwaddr: wlan_cfg80211_set_hwaddr :e8:c7:4f:28:e0:90 ret: 0 
[   51.003779] wlan: [3515:I:ANY] ol_ath_set_config_param: set TXBF_SND_PERIOD: val 100 stat 0
[   51.136539] wlan: [0:I:ANY] ol_ath_set_config_param: Disconnect_timeout value: 10
[   51.181056] wlan: [0:I:ANY] ol_ath_set_config_param: Reconfiguration_timeout value:60
number of vifs: 
iface_mgr: ifacemgr_load_conf_file: 275: iptr->stavap_scan_time:120
iface_mgr: ifacemgr_load_conf_file: 280: iptr->periodic_scan_time:600
iface_mgr: ifacemgr_load_conf_file: 413: No STA VAPs are configured
iface_mgr: ifacemgr_load_conf_file: 416: No PLC ifaces are configured
iface_mgr: ifacemgr_load_conf_file: 422: num_sta_vaps:0 num_plc_ifaces:0 drv_mode:1 same_ssid_support:1 Mode:4
iface_mgr: wlanIfConfigInitIface: 432: wlanIfConfigInitIface: wlanIf 0

Create event socket port 951
iface_mgr: wlanIfConfigInitIface: 448: wlanIfConfigInitIface: wlanIf Iface Manager 0x54b379e0 INIT DONE

Could not open son config file
son: Exiting son_main_function
****** Starting QDSS for qcn6122 pci0 ********
****** Starting QDSS for qcn6122 pci1 ********
[   52.146902] coresight-funnel 6130000.funnel: FUNNEL inport 5 enabled
[   52.147226] coresight-funnel 6041000.funnel: FUNNEL inport 7 enabled
[   52.153302] coresight-tmc 6048000.tmc: TMC enabled
[   52.159092] coresight-replicator-qcom 6046000.replicator: REPLICATOR enabled
[   52.163268] coresight-tmc 6047000.tmc: TMC enabled
[   52.170675] coresight-funnel 6041000.funnel: FUNNEL inport 7 enabled
[   52.175155] coresight-stm 6002000.stm: STM tracing enabled
***** QDSS Tracing Configuration completed *******
****** Starting QDSS for Integrated ********
[   54.800233] mc_attach: enabled snooping on br-gre.
[   54.803870] mc_attach: enabled snooping on br-vsgre.
[   55.244700] wlan: [3773:I:ANY] ol_ath_iw_setcountry: [ol_ath_iw_setcountry][1857] *p=0, *(p+1)=0
[   55.244700] 
[   55.245300] wlan: [3773:I:ANY] ol_ath_ucfg_set_country: ol_ath_ucfg_set_country: Unable to set country code
[   55.255827] wlan: [3773:I:ANY] ieee80211_chan2mode: ieee80211_chan2mode: cannot map channel to mode; freq 0 flags 0x0
[   55.265929] wlan: [3773:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[   55.275059] wlan: [3773:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   55.281374] wlan: [3773:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0
[   55.303671] wlan: [3776:I:ANY] ol_ath_iw_setcountry: [ol_ath_iw_setcountry][1857] *p=0, *(p+1)=0
[   55.303671] 
[   55.304213] wlan: [965:E:TIF] tgt_reg_chan_list_ext_update_handler: Failed to process master ext channel list handler
[   55.313050] wlan: [3776:I:ANY] ol_ath_ucfg_set_country: ol_ath_ucfg_set_country: Unable to set country code
[   55.361079] wlan: [3776:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   55.361728] wlan: [3776:E:ANY] dfs_init_chan_state_array: channel state array initialized
[   55.369026] wlan: [3776:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   55.375430] wlan: [3776:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   55.382035] wlan: [3776:I:ANY] number of channels: 2G = 0 5G = 25, 6G = 0
[   55.956099] receive msg len = 180 cmd 102430
[   55.956139]  <_1xclient_opt_set:654> KMS config usrname <>-passwd <>-port <eth0>-enable 0 msg type 1--
[   55.959434] return ret = 0
[   56.186335] KMS register pid=3712, kfppd started
[   56.186652] CLIENT set start[0]
[   56.332543] wlan: [3938:I:ANY] ol_ath_iw_setcountry: [ol_ath_iw_setcountry][1857] *p=55, *(p+1)=53
[   56.332543] 
[   56.333934] wlan: [3938:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[   56.342150] wlan: [3938:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   56.349070] wlan: [3938:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0
[   56.369671] wlan: [3939:I:ANY] ol_ath_iw_setcountry: [ol_ath_iw_setcountry][1857] *p=55, *(p+1)=53
[   56.369671] 
[   56.382729] wlan: [3939:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   56.383288] wlan: [3939:E:ANY] dfs_init_chan_state_array: channel state array initialized
[   56.390687] wlan: [3939:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   56.397197] wlan: [3939:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   56.403628] wlan: [3939:I:ANY] number of channels: 2G = 0 5G = 25, 6G = 0
[   56.855374] mc_detach: disabled snooping on br-wan.
[   56.855579] mc_detach: disabled snooping on br-vsgre.
[   56.859474] mc_detach: disabled snooping on br-gre.
[   56.864441] mc_detach: disabled snooping on br-lan.
qcawifi qcawificfg80211 disable radio wifi0
qcawifi qcawificfg80211 disable radio wifi1
qcawifi qcawificfg80211: enable radio wifi0
[   59.458252] wlan: [4640:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[   59.458383] wlan: [4640:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   59.464054] wlan: [4640:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0
[   59.476934] wlan: [4640:I:ANY] wlan_cfg80211_set_country: wlan_cfg80211_set_country: Country: US ret: 0 
[   59.756132] wlan: [4658:I:ANY] wlan_cfg80211_set_hwaddr: wlan_cfg80211_set_hwaddr :e8:c7:4f:28:e0:80 ret: -16 
[   59.801347] wlan: [4661:I:ANY] ol_ath_set_config_param: set TXBF_SND_PERIOD: val 100 stat 0
[   59.936411] wlan: [0:I:ANY] ol_ath_set_config_param: Disconnect_timeout value: 10
[   59.980425] wlan: [0:I:ANY] ol_ath_set_config_param: Reconfiguration_timeout value:60
[   60.353009] mc_attach: enabled snooping on br-wan.
[   60.353557] mc_attach: enabled snooping on br-lan.
[   60.383907] mc_attach: enabled snooping on br-gre.
[   60.384442] mc_attach: enabled snooping on br-vsgre.
number of vifs: 
qcawifi qcawificfg80211: enable radio wifi1
[   62.391141] wlan: [5282:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   62.391725] wlan: [5282:E:ANY] dfs_init_chan_state_array: channel state array initialized
[   62.399314] wlan: [5282:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[   62.405704] wlan: [5282:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[   62.412274] wlan: [5282:I:ANY] number of channels: 2G = 0 5G = 25, 6G = 0
[   62.425028] wlan: [5282:I:ANY] wlan_cfg80211_set_country: wlan_cfg80211_set_country: Country: US ret: 0 
[   62.729590] wlan: [5316:I:ANY] wlan_cfg80211_set_hwaddr: wlan_cfg80211_set_hwaddr :e8:c7:4f:28:e0:90 ret: -16 
[   62.774518] wlan: [5319:I:ANY] ol_ath_set_config_param: set TXBF_SND_PERIOD: val 100 stat 0
[   62.923846] wlan: [0:I:ANY] ol_ath_set_config_param: Disconnect_timeout value: 10
[   62.967490] wlan: [0:I:ANY] ol_ath_set_config_param: Reconfiguration_timeout value:60
number of vifs: 
iface_mgr: ifacemgr_load_conf_file: 275: iptr->stavap_scan_time:120
iface_mgr: ifacemgr_load_conf_file: 280: iptr->periodic_scan_time:600
iface_mgr: ifacemgr_load_conf_file: 413: No STA VAPs are configured
iface_mgr: ifacemgr_load_conf_file: 416: No PLC ifaces are configured
iface_mgr: ifacemgr_load_conf_file: 422: num_sta_vaps:0 num_plc_ifaces:0 drv_mode:1 same_ssid_support:1 Mode:4
iface_mgr: wlanIfConfigInitIface: 432: wlanIfConfigInitIface: wlanIf 0

Create event socket port 951
iface_mgr: wlanIfConfigInitIface: 448: wlanIfConfigInitIface: wlanIf Iface Manager 0x54bab9e0 INIT DONE

Could not open son config file
son: Exiting son_main_function
****** Starting QDSS for qcn6122 pci0 ********
****** Starting QDSS for qcn6122 pci1 ********
****** Starting QDSS for Integrated ********
[   63.965101] device eth1 entered promiscuous mode
[   63.969477] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   63.969529] br-lan: port 1(eth1) entered forwarding state
[   63.974584] br-lan: port 1(eth1) entered forwarding state
[   64.966234] br-lan: port 1(eth1) entered disabled state
>>>>VAP SYSTEM READY<<<<
[  179.334196] mc_detach: disabled snooping on br-wan.
[  179.334512] mc_detach: disabled snooping on br-vsgre.
[  179.339465] mc_detach: disabled snooping on br-gre.
[  179.343343] mc_detach: disabled snooping on br-lan.
qcawifi qcawificfg80211 disable radio wifi0
qcawifi qcawificfg80211 disable radio wifi1
[  179.929728] device eth1 left promiscuous mode
[  179.929872] br-lan: port 1(eth1) entered disabled state
[  180.043365] wlan: [6055:I:ANY] ol_ath_iw_setcountry: [ol_ath_iw_setcountry][1857] *p=55, *(p+1)=53
[  180.043365] 
[  180.044769] wlan: [6055:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[  180.053081] wlan: [6055:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[  180.059830] wlan: [6055:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0
[  180.080640] wlan: [6056:I:ANY] ol_ath_iw_setcountry: [ol_ath_iw_setcountry][1857] *p=55, *(p+1)=53
[  180.080640] 
[  180.093635] wlan: [6056:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[  180.094212] wlan: [6056:E:ANY] dfs_init_chan_state_array: channel state array initialized
[  180.101676] wlan: [6056:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[  180.108099] wlan: [6056:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[  180.114531] wlan: [6056:I:ANY] number of channels: 2G = 0 5G = 25, 6G = 0
qcawifi qcawificfg80211 disable radio wifi0
qcawifi qcawificfg80211 disable radio wifi1
qcawifi qcawificfg80211: enable radio wifi0
[  183.236629] wlan: [6751:I:ANY] wlan_scan_update_channel_list: num_chan: 11
[  183.236803] wlan: [6751:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[  183.242512] wlan: [6751:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0
[  183.255477] wlan: [6751:I:ANY] wlan_cfg80211_set_country: wlan_cfg80211_set_country: Country: US ret: 0 
[  183.542026] wlan: [6769:I:ANY] wlan_cfg80211_set_hwaddr: wlan_cfg80211_set_hwaddr :e8:c7:4f:28:e0:80 ret: -16 
[  183.587406] wlan: [6773:I:ANY] ol_ath_set_config_param: set TXBF_SND_PERIOD: val 100 stat 0
[  183.721653] wlan: [0:I:ANY] ol_ath_set_config_param: Disconnect_timeout value: 10
[  183.766691] wlan: [0:I:ANY] ol_ath_set_config_param: Reconfiguration_timeout value:60
number of vifs: cfg033579 
[  184.308300] wlan: [6839:I:ANY] wlan_cfg80211_add_virtual_intf: proprietary mode 6 for interface: ath0 : clone params: 0x00000001 
[  184.308413] wlan: [6839:I:MBSSIE] osif_mbssid_sanity_check: mbssid_sanity_ok: YES
[  184.319189] wlan: [6839:I:ANY] osifp_create_wlan_vap: VDEV Create e8:c7:4f:28:e0:80
[  184.326647] wlan: [6839:I:ANY] wlan_vap_create: devhandle=0x959e0500, opmode=IEEE80211_M_HOSTAP, flags=0x1
[  184.326647] 
[  184.334351] wlan: [6839:I:ANY] ol_ath_vap_set_param: Setting SGI value: 1
[  184.345301] wlan: [6839:I:ANY] ol_ath_vap_set_param: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:0|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0|dl_muofdma_bfer:0
[  184.352121] wlan: [6839:I:ANY] ol_ath_vap_set_param: he_bf_cap=0x33
[  184.366526] wlan: [6839:I:ANY] ol_ath_vap_set_param: VDEV params: AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[  184.372675] wlan: [6839:I:ANY] MBO Initialized
[  184.386689] wlan: [6839:I:ANY] OCE Initialized
[  184.390753] wlan: [6839:I:ANY] osif_nss_ol_vap_create: NSS wifi offload VAP create IF 30 nss_id -1 
[  184.395155] wlan: [6839:I:ANY] osif_nss_ol_vap_create: NSS radio_if 28
[  184.404471] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: VDEV configuration success: 0
[  184.410753] wlan: [6839:I:ANY] osif_nss_ol_vap_create: vap create 89478500 : if_num 30 
[  184.418962] wlan: [6839:E:ANY] wlan_create_attach_vdev_rawsim_ctxt: simulation module not registerd
[  184.446085] wlan: [6839:I:ANY] osif_create_vap_complete: TX Checksum:1|SG:1|TSO:1|LRO:0
[  184.446125] wlan: [6839:I:ANY] WLAN-NSS: VAP NSS ops initialized 
[  184.457975] wlan: [6839:I:ANY] VAP device ath0 created osifp: (89478500) os_if: (89480000)
[  185.651469] 8021q: adding VLAN 0 to HW filter on device ath0
[  185.654205] device ath0 entered promiscuous mode
[  185.656981] wlan: [0:E:NSS] [nss-wifi-mac-db-nfy]: No entries
[  185.660845] br-lan: port 1(ath0) entered forwarding state
[  185.666573] br-lan: port 1(ath0) entered forwarding state
[  185.697087] wlan: [1165:I:ANY] wlan_cfg80211_do_acs: vap-0(ath0):ACS Params
[  185.697129] wlan: [1165:I:ANY] wlan_cfg80211_do_acs: ht_enabled:1|ht40_enabled:0|vht_enabled:0|hw_mode:8|chwidth:20|
qcawifi qcawificfg80211: enable radio wifi1
[  187.656685] wlan: [7489:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[  187.657261] wlan: [7489:E:ANY] dfs_init_chan_state_array: channel state array initialized
[  187.664523] wlan: [7489:I:ANY] wlan_scan_update_channel_list: num_chan: 25
[  187.671331] wlan: [7489:I:ANY] ieee80211_setctry_tryretaining_curchan: [442] Skipping current channel retention during set_country operation
[  187.678556] wlan: [7489:I:ANY] number of channels: 2G = 0 5G = 25, 6G = 0
[  187.690659] wlan: [7489:I:ANY] wlan_cfg80211_set_country: wlan_cfg80211_set_country: Country: US ret: 0 
[  187.975552] wlan: [7508:I:ANY] wlan_cfg80211_set_hwaddr: wlan_cfg80211_set_hwaddr :e8:c7:4f:28:e0:90 ret: -16 
[  188.020777] wlan: [7511:I:ANY] ol_ath_set_config_param: set TXBF_SND_PERIOD: val 100 stat 0
[  188.154922] wlan: [0:I:ANY] ol_ath_set_config_param: Disconnect_timeout value: 10
[  188.198658] wlan: [0:I:ANY] ol_ath_set_config_param: Reconfiguration_timeout value:60
number of vifs: cfg043579 
[  188.619669] wlan: [7574:I:ANY] wlan_cfg80211_add_virtual_intf: proprietary mode 6 for interface: ath1 : clone params: 0x00000001 
[  188.619755] wlan: [7574:I:MBSSIE] osif_mbssid_sanity_check: mbssid_sanity_ok: YES
[  188.630658] wlan: [7574:I:ANY] osifp_create_wlan_vap: VDEV Create e8:c7:4f:28:e0:90
[  188.638053] wlan: [7574:I:ANY] wlan_vap_create: devhandle=0x92fc0500, opmode=IEEE80211_M_HOSTAP, flags=0x1
[  188.638053] 
[  188.645902] wlan: [7574:I:ANY] ol_ath_vap_set_param: Setting SGI value: 1
[  188.656666] wlan: [7574:I:ANY] ol_ath_vap_set_param: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:0|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0
[  188.663298] wlan: [7574:I:ANY] ol_ath_vap_set_param: he_bf_cap=0x73
[  188.677983] wlan: [7574:I:ANY] ol_ath_vap_set_param: VDEV params: AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[  188.684033] wlan: [7574:I:ANY] MBO Initialized
[  188.698381] wlan: [7574:I:ANY] OCE Initialized
[  188.702203] wlan: [7574:I:ANY] osif_nss_ol_vap_create: NSS wifi offload VAP create IF 31 nss_id -1 
[  188.706726] wlan: [7574:I:ANY] osif_nss_ol_vap_create: NSS radio_if 29
[  188.715664] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: VDEV configuration success: 0
[  188.722116] wlan: [7574:I:ANY] osif_nss_ol_vap_create: vap create 894f6500 : if_num 31 
[  188.730316] wlan: [7574:E:ANY] wlan_create_attach_vdev_rawsim_ctxt: simulation module not registerd
[  188.756073] wlan: [7574:I:ANY] osif_create_vap_complete: TX Checksum:1|SG:1|TSO:1|LRO:0
[  188.756112] wlan: [7574:I:ANY] WLAN-NSS: VAP NSS ops initialized 
[  188.768221] wlan: [7574:I:ANY] VAP device ath1 created osifp: (894f6500) os_if: (894f8000)
[  189.183364] wlan: [2046:E:ANY] ol_ath_get_chan_grade_info: RF characterization entries is empty
[  189.183658] wlan: [2046:I:ANY] vap-0(ath0): ACS result PCH 6 freq 2437, SCH 0 freq 0, hw_mode 1 chwidth 20, vht_seg0 6 freq 2437, vht_seg1 0 freq 0
[  189.191293] wlan: [2046:I:ANY] ieee80211_acs_scan_evhandler: [EXT] lock held duration (8ms)
[  189.192848] wlan: [1165:I:ANY] DES SSID SET=Wireless_28:e0:80
[  189.192879] wlan: [1165:I:ANY] desired hw mode: 8
[  189.193163] wlan: [1165:I:ANY] ieee80211_ucfg_set_freq_internal: 
[  189.193163]  Channel is configured already!!
[  189.193307] wlan: [1165:E:MBSSIE] ieee80211_ucfg_set_txvap: MBSSID is not enabled
[  189.193465] wlan: [0:I:ANY] wlan_acs_start_scan_report: [EXT] Invoking ACS module for ACS report
[  189.947087] mc_attach: enabled snooping on br-wan.
[  189.947579] mc_attach: enabled snooping on br-lan.
[  189.966977] mc_attach: enabled snooping on br-gre.
[  189.967322] mc_attach: enabled snooping on br-vsgre.
[  190.077111] 8021q: adding VLAN 0 to HW filter on device ath1
[  190.080710] device ath1 entered promiscuous mode
[  190.082666] br-lan: port 2(ath1) entered forwarding state
[  190.086652] br-lan: port 2(ath1) entered forwarding state
[  190.127394] wlan: [1165:I:ANY] wlan_cfg80211_do_acs: vap-0(ath1):ACS Params
[  190.127438] wlan: [1165:I:ANY] wlan_cfg80211_do_acs: ht_enabled:1|ht40_enabled:0|vht_enabled:0|hw_mode:7|chwidth:20|
****** Starting QDSS for qcn6122 pci0 ********
****** Starting QDSS for qcn6122 pci1 ********
****** Starting QDSS for Integrated ********
[  190.772507] device eth1 entered promiscuous mode
[  190.775736] Unexpected msg:0x1 received!
[  190.778286] Unexpected msg:0x1 received!
[  190.791787] wlan: [7902:I:ANY] ol_ath_vap_set_param: Setting SGI value: 1
[  190.792030] wlan: [0:E:CMN_MLME] mlme_vdev_restart_is_allowed:  No multivdev restart
[  190.809982] wlan: [0:E:CMN_MLME] mlme_vdev_restart_is_allowed:  No multivdev restart
[  190.822242] wlan: [7908:I:ANY] ieee80211_ucfg_setparam: Setting Max Stations:6
[  190.874166] wlan: [7918:I:ANY] ol_ath_vap_set_param: Setting SGI value: 1
[  190.893669] wlan: [7920:I:ANY] ieee80211_ucfg_setparam: Setting Max Stations:6
[  197.997310] wlan: [2046:E:ANY] ol_ath_get_chan_grade_info: RF characterization entries is empty
[  197.997900] wlan: [2046:I:ANY] vap-0(ath1): ACS result PCH 36 freq 5180, SCH 0 freq 0, hw_mode 2 chwidth 20, vht_seg0 36 freq 5180, vht_seg1 0 freq 0
[  198.004861] wlan: [2046:I:ANY] ieee80211_acs_scan_evhandler: [EXT] lock held duration (7ms)
[  198.006469] wlan: [1165:I:ANY] DES SSID SET=Wireless_28:e0:80_5G
[  198.006481] wlan: [1165:I:ANY] desired hw mode: 7
[  198.006754] wlan: [1165:I:ANY] ieee80211_ucfg_set_freq_internal: 
[  198.006754]  Channel is configured already!!
[  198.006942] wlan: [1165:E:MBSSIE] ieee80211_ucfg_set_txvap: MBSSID is not enabled
[  198.007100] wlan: [0:I:ANY] wlan_acs_start_scan_report: [EXT] Invoking ACS module for ACS report
[  200.686009] br-lan: port 1(ath0) entered forwarding state
[  205.126073] br-lan: port 2(ath1) entered forwarding state
5

The flash layout based on the bootlog should be like this:

Partitions as detected by kernel at boot:
0x000000000000-0x000000030000 : "0:SBL1"          192 KiB
0x000000030000-0x000000040000 : "0:MIBIB"          64 KiB
0x000000040000-0x000000050000 : "0:BOOTCONFIG"     64 KiB
0x000000050000-0x000000060000 : "0:BOOTCONFIG1"    64 KiB
0x000000060000-0x000000100000 : "0:QSEE"          640 KiB
0x000000100000-0x0000001a0000 : "0:QSEE_1"        640 KiB
0x0000001a0000-0x0000001b0000 : "0:DEVCFG"         64 KiB
0x0000001b0000-0x0000001c0000 : "0:DEVCFG_1"       64 KiB
0x0000001c0000-0x0000001d0000 : "0:CDT"            64 KIB
0x0000001d0000-0x0000001e0000 : "0:CDT_1"          64 KiB
0x0000001e0000-0x0000001f0000 : "0:APPSBLENV"      64 KiB
0x0000001f0000-0x000000290000 : "0:APPSBL"        640 KiB  (U-Boot)
0x000000290000-0x000000330000 : "0:APPSBL_1"      640 KiB
0x000000330000-0x0000003a0000 : "0:ART"           448 KiB  (WiFi cal)
0x0000003a0000-0x0000003c0000 : "0:boarddata"     128 KiB
0x0000003c0000-0x0000007c0000 : "0:USERCONFIG"      4 MiB
0x0000007c0000-0x000000bc0000 : "0:data"            4 MiB
0x000000bc0000-0x000000c40000 : "0:dump"          512 KiB
Total: 16 MiB = full NOR flash

And this for NAND :

0x000000000000-0x000000080000 : "0:TRAINING"    512 KiB
0x000000080000-0x000003e80000 : "rootfs"         62 MiB  (active)
0x000003e80000-0x000007c80000 : "rootfs_1"       62 MiB  (backup)
Total: 125 MiB used of 128 MiB
6

1000051984
10000519841920×3412 864 KB

1000052200
1000052200900×1600 417 KB

1000052199
10000521991600×900 298 KB

1000052198
10000521981600×900 361 KB

1000051989
1000051989900×1600 281 KB

7

a multi-meter will help identify the missing cap. Once you find where the cap is missing, replace it or just use a wee blob of solder to bridge the gap

8

C9509 is a capacitor, bridging may damage something ...
capacitors on serial (tty) lines are unusual.

10

Sorry for late response,

Thanks for your advice, but after i look properly, the C9509 label is located between RX header and GND like this :

RX pin header<======C9509======>GND

I don't think that's will be good idea to use wee blob or jumper the c label.

I don't have multi-meter right now, so I can't do that.

Maybe in a week or two I will send the update.

11

Thanks for the advice, as you said capacitor on serial (tty) line is unusual because serial use DC instead of AC so the capacitor will block the signal instead.