Hi,
I added support for this board in my staging tree.
Could you build and test it please?
Thanks,
Koen
Hi Koen!
Not working unfortunately.
RouterBOOT booter 3.41
RouterBoard 2011UiAS-2HnD r2
CPU frequency: 600 MHz
Memory speed: 200 MHz
Memory size: 128 MiB
NAND size: 128 MiB
Press any key within 2 seconds to enter setup..
writing settings to flash... OK
trying dhcp protocol..................... OK
resolved mac address 00:E0:4C:60:75:20
Gateway: 192.168.1.10
transfer started ........................................................ transfer ok, time=6.12s
setting up elf image... OK
jumping to kernel code
[ 0.000000] Linux version 4.14.111 (bota@NorbiPC) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9860-2a6950a634)) #0 Fri Apr 12 09:08:43 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: lcd_ctrl=84 parts=1 boot_part_size=4194304 gpio=249403 HZ=300000000 mem=128M kmac=B8:69:F4:A4:E4:D0 board=2011r5 board=2011r5 ver=3.41 hw_opt=00718004 boot=1 mlc=11 console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 122060K/131072K available (3941K kernel code, 166K rwdata, 892K rodata, 2224K init, 205K bss, 9012K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] Clocks: CPU:600.000MHz, DDR:400.000MHz, AHB:400.000MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[ 0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[ 0.008853] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.085988] pid_max: default: 32768 minimum: 301
[ 0.091443] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.098955] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.109368] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.120576] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.127976] NET: Registered protocol family 16
[ 0.137671] MIPS: machine is Mikrotik RouterBOARD 2011UiAS-2HnD r2
[ 0.645862] clocksource: Switched to clocksource MIPS
[ 0.652599] NET: Registered protocol family 2
[ 0.658351] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.666313] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.673531] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.680884] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.687562] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.694927] NET: Registered protocol family 1
[ 2.575875] random: fast init done
[ 3.150017] Crashlog allocated RAM at address 0x3f00000
[ 3.157330] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 3.169467] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.176128] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.330231] io scheduler noop registered
[ 3.334688] io scheduler deadline registered (default)
[ 3.340826] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 3.348467] console [ttyS0] disabled
[ 3.372683] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 3.382487] console [ttyS0] enabled
[ 3.382487] console [ttyS0] enabled
[ 3.390042] bootconsole [early0] disabled
[ 3.390042] bootconsole [early0] disabled
[ 3.402478] m25p80 spi0.0: found w25x05, expected m25p80
[ 3.419073] m25p80 spi0.0: w25x05 (64 Kbytes)
[ 3.468705] Creating 4 MTD partitions on "spi0.0":
[ 3.473676] 0x000000000000-0x00000000c000 : "routerboot"
[ 3.502972] 0x00000000c000-0x00000000d000 : "hard_config"
[ 3.532412] 0x00000000d000-0x00000000e000 : "bios"
[ 3.561408] 0x00000000e000-0x00000000f000 : "soft_config"
[ 3.592110] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
[ 3.598726] nand: Winbond NAND 128MiB 3,3V 8-bit
[ 3.603497] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 3.611361] Scanning device for bad blocks
[ 3.689562] Creating 3 MTD partitions on "ar934x-nfc":
[ 3.694890] 0x000000000000-0x000000040000 : "booter"
[ 3.723725] 0x000000040000-0x000000400000 : "kernel"
[ 3.752766] 0x000000400000-0x000008000000 : "ubi"
[ 3.784898] libphy: Fixed MDIO Bus: probed
[ 3.915062] libphy: ag71xx_mdio: probed
[ 3.950259] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 4.964556] libphy: ag71xx_mdio: probed
[ 5.597327] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 5.608900] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 6.237641] ag71xx-mdio.1: Found an AR934X built-in switch
[ 6.289901] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 6.297626] NET: Registered protocol family 10
[ 6.305951] Segment Routing with IPv6
[ 6.309858] NET: Registered protocol family 17
[ 6.314500] 8021q: 802.1Q VLAN Support v1.8
[ 6.322533] UBI error: no valid UBI magic found inside mtd6
[ 6.339131] Freeing unused kernel memory: 2224K
[ 6.343819] This architecture does not have kernel memory protection.
[ 6.364739] init: Console is alive
[ 6.368647] init: - watchdog -
[ 6.394999] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.414311] usbcore: registered new interface driver usbfs
[ 6.420119] usbcore: registered new interface driver hub
[ 6.425695] usbcore: registered new device driver usb
[ 6.436394] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.444775] ehci-platform: EHCI generic platform driver
[ 6.450324] ehci-platform ehci-platform: EHCI Host Controller
[ 6.456320] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 6.466599] ehci-platform ehci-platform: TX-TX IDP fix enabled
[ 6.472639] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.505882] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.513184] hub 1-0:1.0: USB hub found
[ 6.517492] hub 1-0:1.0: 1 port detected
[ 6.524619] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.532594] ohci-platform: OHCI generic platform driver
[ 6.538888] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.548777] init: - preinit -
[ 6.820401] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.017492] eth0: link up (1000Mbps/Full duplex)
[ 8.022472] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.036408] eth0: link down
[ 10.050980] procd: - early -
[ 10.054067] procd: - watchdog -
[ 10.614813] procd: - watchdog -
[ 10.618408] procd: - ubus -
[ 10.628208] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.671912] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.678979] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.686622] procd: - init -
Please press Enter to activate this console.
[ 10.880621] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.893867] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.909528] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
[ 10.917402] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
[ 10.927233] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.941619] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 11.005969] xt_time: kernel timezone is -0000
[ 11.070852] PPP generic driver version 2.4.2
[ 11.077973] NET: Registered protocol family 24
[ 11.144317] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[ 11.226303] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.446270] urandom_read: 5 callbacks suppressed
[ 12.446278] random: jshn: uninitialized urandom read (4 bytes read)
[ 12.530706] random: jshn: uninitialized urandom read (4 bytes read)
[ 48.554431] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 48.562331] eth0: link up (1000Mbps/Full duplex)
[ 48.576106] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 48.587431] br-lan: port 1(eth0.1) entered blocking state
[ 48.593020] br-lan: port 1(eth0.1) entered disabled state
[ 48.598987] device eth0.1 entered promiscuous mode
[ 48.603937] device eth0 entered promiscuous mode
[ 48.684271] br-lan: port 1(eth0.1) entered blocking state
[ 48.689906] br-lan: port 1(eth0.1) entered forwarding state
[ 48.695888] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 48.974185] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 49.029110] br-lan: port 2(eth1.1) entered blocking state
[ 49.034703] br-lan: port 2(eth1.1) entered disabled state
[ 49.040673] device eth1.1 entered promiscuous mode
[ 49.045628] device eth1 entered promiscuous mode
[ 49.616236] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 110.345916] random: crng init done
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r9860-2a6950a634
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# sysupgrade -n /tmp/oproot@OpenWrt:/# sysupgrade -n /tmp/openwrt-ar71xx-mikrotik-nand-large-squashfs-sysupgrade.bin
Image metadata not found
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... odhcp6c ntpd dnsmasq ubusd logd netifd odhcpd
Sending KILL to remaining processes ...
Performing system upgrade...
Could not open mtd device: firmware
Can't open device for writing!
cat: write error: Broken pipe
sysupgrade aborted with return code: 256
[ 749.554665] reboot: Restarting system
RouterBOOT booter 3.41
RouterBoard 2011UiAS-2HnD r2
CPU frequency: 600 MHz
Memory speed: 200 MHz
Memory size: 128 MiB
NAND size: 128 MiB
Press any key within 2 seconds to enter setup..
loading kernel... OK
setting up elf image... OK
jumping to kernel code
Starting...
Starting services...
MikroTik 6.44.1 (stable)
Thanks for testing.
Can you provide me the info from /etc/board.json after booting the RAM image?
Koen
/etc/board.json
{
"model": {
"id": "rb-2011uias-2hnd-r2",
"name": "Mikrotik RouterBOARD 2011UiAS-2HnD r2"
},
"led": {
"eth6": {
"name": "ETH6",
"sysfs": "rb:green:eth6",
"trigger": "switch1",
"type": "switch",
"mode": "",
"port_mask": "0x20",
"speed_mask": ""
},
"eth7": {
"name": "ETH7",
"sysfs": "rb:green:eth7",
"trigger": "switch1",
"type": "switch",
"mode": "",
"port_mask": "0x10",
"speed_mask": ""
},
"eth8": {
"name": "ETH8",
"sysfs": "rb:green:eth8",
"trigger": "switch1",
"type": "switch",
"mode": "",
"port_mask": "0x08",
"speed_mask": ""
},
"eth9": {
"name": "ETH9",
"sysfs": "rb:green:eth9",
"trigger": "switch1",
"type": "switch",
"mode": "",
"port_mask": "0x04",
"speed_mask": ""
},
"eth10": {
"name": "ETH10",
"sysfs": "rb:green:eth10",
"trigger": "switch1",
"type": "switch",
"mode": "",
"port_mask": "0x02",
"speed_mask": ""
}
},
"switch": {
"switch0": {
"enable": true,
"reset": true,
"ports": [
{
"num": 0,
"device": "eth0",
"need_tag": false,
"want_untag": false
},
{
"num": 2,
"role": "lan"
},
{
"num": 3,
"role": "lan"
},
{
"num": 4,
"role": "lan"
},
{
"num": 5,
"role": "lan"
},
{
"num": 1,
"role": "wan"
},
{
"num": 6,
"role": "sfp"
}
],
"roles": [
{
"role": "lan",
"ports": "2 3 4 5 0t",
"device": "eth0.1"
},
{
"role": "wan",
"ports": "1 0t",
"device": "eth0.2"
},
{
"role": "sfp",
"ports": "6 0t",
"device": "eth0.3"
}
]
},
"switch1": {
"enable": true,
"reset": true,
"ports": [
{
"num": 0,
"device": "eth1",
"need_tag": false,
"want_untag": false
},
{
"num": 1,
"role": "lan"
},
{
"num": 2,
"role": "lan"
},
{
"num": 3,
"role": "lan"
},
{
"num": 4,
"role": "lan"
},
{
"num": 5,
"role": "lan"
}
],
"roles": [
{
"role": "lan",
"ports": "1 2 3 4 5 0t",
"device": "eth1.1"
}
]
}
},
"network": {
"lan": {
"ifname": "eth0.1 eth1.1",
"protocol": "static"
},
"wan": {
"ifname": "eth0.2",
"protocol": "dhcp"
},
"sfp": {
"ifname": "eth0.3",
"protocol": "none"
}
}
}
I found a missing item in the initial patch.
The commit in my staging has been updated.
Could you please rebuild & retry?
Thanks,
Koen
Installed 
root@OpenWrt:/# sysupgrade -n /tmp/openwrt-ar71xx-mikrotik-nand-large-squashfs-sysupgrade.bin
Image metadata not found
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... udhcpc odhcp6c ntpd dnsmasq ubusd logd netifd odhcpd
Sending KILL to remaining processes ...
Performing system upgrade...
Unlocking kernel ...
Erasing kernel ...
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000
Writing data to block 3 at offset 0x60000
Writing data to block 4 at offset 0x80000
Writing data to block 5 at offset 0xa0000
Writing data to block 6 at offset 0xc0000
Writing data to block 7 at offset 0xe0000
Writing data to block 8 at offset 0x100000
Writing data to block 9 at offset 0x120000
Writing data to block 10 at offset 0x140000
Writing data to block 11 at offset 0x160000
Writing data to block 12 at offset 0x180000
Writing data to block 13 at offset 0x1a0000
[ 173.254617] ubi0: attaching mtd6
[ 173.975251] ubi0: scanning is finished
[ 173.979448] ubi0 error: ubi_read_volume_table: the layout volume was not found
[ 173.987205] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd6, error -22
ubiattach: error!: cannot attach mtd6
error 22 (Invalid argument)
ubiformat: mtd6 (nand), size 130023424 bytes (124.0 MiB), 992 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 991 -- 100 % complete
ubiformat: 859 eraseblocks are supposedly empty
ubiformat: warning!: 133 of 992 eraseblocks contain non-UBI data
ubiformat: warning!: only 0 of 992 eraseblocks have valid erase counter
ubiformat: erase counter 0 will be used for all eraseblocks
ubiformat: note, arbitrary erase counter value may be specified using -e option
ubiformat: use erase counter 0 for all eraseblocks
ubiformat: formatting eraseblock 991 -- 100 % complete
[ 184.821109] ubi0: scanning is finished
[ 184.841782] ubi0: attached mtd6 (name "ubi", size 124 MiB)
[ 184.847514] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 184.854615] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 184.861635] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 184.868836] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[ 184.875043] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[ 184.882513] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 103011554
[ 184.891865] ubi0: available PEBs: 968, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20
[ 184.906021] ubi0: background thread "ubi_bgt0d" started, PID 1643
UBI device number 0, total 992 LEBs (125960192 bytes, 120.1 MiB), available 968 LEBs (122912768 bytes, 117.2 MiB), LEB size 126976 bytes (124.0 KiB)
Volume ID 0, size 14 LEBs (1777664 bytes, 1.6 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "none", alignment 1
Volume ID 1, size 18 LEBs (2285568 bytes, 2.1 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 118849536
Volume ID 2, size 936 LEBs (118849536 bytes, 113.3 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
umount: can't unmount /: Invalid argument
[ 186.777318] reboot: Restarting system
RouterBOOT booter 3.41
RouterBoard 2011UiAS-2HnD r2
CPU frequency: 600 MHz
Memory speed: 200 MHz
Memory size: 128 MiB
NAND size: 128 MiB
Press any key within 2 seconds to enter setup..
loading kernel... OK
setting up elf image... OK
jumping to kernel code
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 4.14.111 (bota@NorbiPC) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9860-5b39e72f6c)) #0 Fri Apr 12 11:56:31 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: lcd_ctrl=84 parts=1 boot_part_size=4194304 gpio=249403 HZ=300000000 mem=128M kmac=B8:69:F4:A4:E4:D0 board=2011r5 board=2011r5 ver=3.41 hw_opt=00718004 boot=1 mlc=11 console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 124044K/131072K available (3941K kernel code, 166K rwdata, 892K rodata, 240K init, 205K bss, 7028K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] Clocks: CPU:600.000MHz, DDR:400.000MHz, AHB:400.000MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[ 0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[ 0.008853] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.085998] pid_max: default: 32768 minimum: 301
[ 0.091454] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.098963] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.109377] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.120584] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.127984] NET: Registered protocol family 16
[ 0.137677] MIPS: machine is Mikrotik RouterBOARD 2011UiAS-2HnD r2
[ 0.645891] clocksource: Switched to clocksource MIPS
[ 0.652631] NET: Registered protocol family 2
[ 0.658385] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.666350] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.673567] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.680921] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.687598] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.694962] NET: Registered protocol family 1
[ 0.704745] Crashlog allocated RAM at address 0x3f00000
[ 0.712068] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.724151] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.730812] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.751834] io scheduler noop registered
[ 0.756334] io scheduler deadline registered (default)
[ 0.762436] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.770075] console [ttyS0] disabled
[ 0.794289] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.804094] console [ttyS0] enabled
[ 0.804094] console [ttyS0] enabled
[ 0.811650] bootconsole [early0] disabled
[ 0.811650] bootconsole [early0] disabled
[ 0.824041] m25p80 spi0.0: found w25x05, expected m25p80
[ 0.840630] m25p80 spi0.0: w25x05 (64 Kbytes)
[ 0.845631] Creating 4 MTD partitions on "spi0.0":
[ 0.850647] 0x000000000000-0x00000000c000 : "routerboot"
[ 0.857844] 0x00000000c000-0x00000000d000 : "hard_config"
[ 0.864784] 0x00000000d000-0x00000000e000 : "bios"
[ 0.871819] 0x00000000e000-0x00000000f000 : "soft_config"
[ 0.880402] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
[ 0.887019] nand: Winbond NAND 128MiB 3,3V 8-bit
[ 0.891788] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.899653] Scanning device for bad blocks
[ 0.908123] random: fast init done
[ 0.959374] Creating 3 MTD partitions on "ar934x-nfc":
[ 0.964697] 0x000000000000-0x000000040000 : "booter"
[ 0.971550] 0x000000040000-0x000000400000 : "kernel"
[ 0.978132] 0x000000400000-0x000008000000 : "ubi"
[ 0.988493] libphy: Fixed MDIO Bus: probed
[ 1.007955] libphy: ag71xx_mdio: probed
[ 1.020867] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 1.746670] libphy: ag71xx_mdio: probed
[ 2.377356] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 2.388941] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.017672] ag71xx-mdio.1: Found an AR934X built-in switch
[ 3.069928] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 3.077632] NET: Registered protocol family 10
[ 3.085961] Segment Routing with IPv6
[ 3.089865] NET: Registered protocol family 17
[ 3.094513] 8021q: 802.1Q VLAN Support v1.8
[ 3.102481] UBI: auto-attach mtd6
[ 3.105982] ubi0: attaching mtd6
[ 4.416058] ubi0: scanning is finished
[ 4.437313] ubi0: attached mtd6 (name "ubi", size 124 MiB)
[ 4.442986] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.450127] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.457145] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.464335] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[ 4.470548] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 4.478022] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 103011554
[ 4.487375] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
[ 4.496987] ubi0: background thread "ubi_bgt0d" started, PID 355
[ 4.504843] block ubiblock0_1: created from ubi0:1(rootfs)
[ 4.510572] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 4.527391] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.535936] Freeing unused kernel memory: 240K
[ 4.540529] This architecture does not have kernel memory protection.
[ 5.157961] init: Console is alive
[ 5.161725] init: - watchdog -
[ 6.308752] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.374009] usbcore: registered new interface driver usbfs
[ 6.379805] usbcore: registered new interface driver hub
[ 6.385398] usbcore: registered new device driver usb
[ 6.395842] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.404235] ehci-platform: EHCI generic platform driver
[ 6.409791] ehci-platform ehci-platform: EHCI Host Controller
[ 6.415765] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 6.426071] ehci-platform ehci-platform: TX-TX IDP fix enabled
[ 6.432112] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.465914] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.473228] hub 1-0:1.0: USB hub found
[ 6.477512] hub 1-0:1.0: 1 port detected
[ 6.484693] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.492670] ohci-platform: OHCI generic platform driver
[ 6.498908] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.508838] init: - preinit -
[ 7.165726] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.177524] eth0: link up (1000Mbps/Full duplex)
[ 8.340960] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.403647] random: procd: uninitialized urandom read (4 bytes read)
[ 10.437312] UBIFS (ubi0:2): default file-system created
[ 10.456559] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 425
[ 10.670450] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 10.678588] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.688840] UBIFS (ubi0:2): FS size: 117452800 bytes (112 MiB, 925 LEBs), journal size 5840896 bytes (5 MiB, 46 LEBs)
[ 10.699799] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 10.706640] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID FE524338-BDE1-4EE3-97DB-4BAFA252E819, small LPT model
[ 10.721035] mount_root: overlay filesystem has not been fully initialized yet
[ 10.728512] random: crng init done
[ 10.732506] mount_root: switching to ubifs overlay
[ 10.766348] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.868662] eth0: link down
[ 10.883243] procd: - early -
[ 10.887068] procd: - watchdog -
[ 11.590226] procd: - watchdog -
[ 11.593777] procd: - ubus -
[ 11.825870] procd: - init -
Please press Enter to activate this console.
[ 12.153677] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.167335] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.183758] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
[ 12.191632] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
[ 12.201494] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.216092] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 12.283967] xt_time: kernel timezone is -0000
[ 12.351231] PPP generic driver version 2.4.2
[ 12.358404] NET: Registered protocol family 24
[ 12.423926] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[ 12.462404] kmodloader: done loading kernel modules from /etc/modules.d/*
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r9860-5b39e72f6c
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.3M 2.3M 0 100% /rom
tmpfs 60.7M 32.0K 60.7M 0% /tmp
/dev/ubi0_2 102.9M 44.0K 98.2M 0% /overlay
overlayfs:/overlay 102.9M 44.0K 98.2M 0% /
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:/#
Nice
Enjoy it.
Regards,
Koen
Thanks for helping.
Regards,
Norbert
Hello Koen
The staging tree version work fine for me. I hope to see the patch in the official branch.
Thanks,
Erwann
fyi, I've pushed the r2 version patch to master.
Regards,
Koen
2 Likes
Hi Koen!
The switch1 leds(6-10) not working on my r2 when the trigger is "Switchport activity (switch1)".
Regards,
Norbert
EDIT: Master image has installed succesfully on my r2
1 Like
Hello RebroN, we have the same problem. Could you give us a link to download the correct sysupgrade file?
thank you very much in advance
If you refer to the led problem, than that problem has not been fixed yet.
Regards,
Norbert
tb2019 via OpenWrt Forum mail@forum.openwrt.org ezt írta (időpont: 2019. ápr. 25., Csü 13:48):
Hi Norbert, my problem is when i load the sysupgrade.bin file the router reboot continously.
I think you solved this problem building a new one. I'd be very grateful if you could tell me how to solve this problem.
Regards,
Tb.
Hi Koen,
Thank you for this.
Your fix also works for the Mikrotik RouterBOARD 2011iLS (5 x fast ethernet, 5 x GBit ethernet, 1x SFP, no Wireless, no USB, No serial terminal from rooterboot) ,
Board identifier seems to be 2011r5
Kernel command line: parts=1 boot_part_size=4194304 gpio=249387 HZ=300000000 mem=64M kmac=B8:69:F4:ba:db:ad board=2011r5 board=2011r5 ver=3.41 hw_opt=00110001 boot=1 mlc=11 console=ttyS0,115200 rootfstype=squashfs noinitrd
byt cpuinfo reports as expected
cat /proc/cpuinfo
system type : Atheros AR9344 rev 3
machine : Mikrotik RouterBOARD 2011iLS
processor : 0
cpu model : MIPS 74Kc V4.12
BogoMIPS : 299.82
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
isa : mips1 mips2 mips32r1 mips32r2
ASEs implemented : mips16 dsp dsp2
shadow register sets : 1
kscratch registers : 0
package : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not available
1 Like
Thanks for testing
I'll let it sit in staging for another week until I'm confident enough that it doesn't break anything else.
If it's stable after more testing, I'll check if it can be added to the 19.07 branch so it will be present in the next official release.
Regards,
Koen
Hello,
Any news or guidance on this one? The only one I could get working as the 19 version of : ECC errors in UBI RB2011UiAS-2HnD-IN (and solution)
However, I'm having lots of troubles with kernel modules as the packages on the openwrt repository requires different kernel version than the one running on this image.
Thanks,
Marcelo
Does anyone have working SFP on these ?
I found this post ( Mikrotik Rb2011ILS-IN SFP port not working ) that mentions that SFP power is connected to a switch LED pin, But I have not managed to get them working using the regular build ( master ) or that proposed fix.