hi
i have caldata for 5GHZ in 2116 BYTE file.
what is the good way to use it for many pcie cards (3).
i name it cal-pci-0000:0x:00:0.bin put it in /lib/firmware/ath10k/.
it seems to work ,the wireless is up there is no errors in log'
my question : how to check that calibration is loaded ? what tool to use for caldata?
how to assign mac addr for each card ?
any hints or guidance are welcome.
best regards.
hi
here is some log from 2 differrent core2duo :
8105] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[ 7.259458] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[ 7.262507] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 7.263792] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 7.265374] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to simplified (2000-8000 ints) mode
[ 7.266793] e1000e 0000:00:19.0: Interrupt Mode set to 1
[ 7.434779] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:24:
[ 7.438123] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 7.441343] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[ 7.449957] usbcore: registered new interface driver ums-alauda
[ 7.452458] usbcore: registered new interface driver ums-cypress
[ 7.454450] usbcore: registered new interface driver ums-datafab
[ 7.456444] usbcore: registered new interface driver ums-freecom
[ 7.457943] usbcore: registered new interface driver ums-isd200
[ 7.459399] usbcore: registered new interface driver ums-jumpshot
[ 7.460868] usbcore: registered new interface driver ums-karma
[ 7.462313] usbcore: registered new interface driver ums-sddr09
[ 7.463723] usbcore: registered new interface driver ums-sddr55
[ 7.465174] usbcore: registered new interface driver ums-usbat
[ 7.470324] xt_time: kernel timezone is -0000
[ 7.504316] PPP generic driver version 2.4.2
[ 7.506146] NET: Registered protocol family 24
[ 7.517719] ath10k_pci 0000:0b:00.0: pci probe 168c:003c 0000:0000
[ 7.517917] ath10k_pci 0000:0b:00.0: boot pci_mem 0x00000000ceb8faa8
[ 7.518141] ath10k_pci 0000:0b:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 7.519376] ath10k_pci 0000:0b:00.0: boot 988x chip reset
[ 7.519378] ath10k_pci 0000:0b:00.0: boot warm reset
[ 7.556692] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.556715] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.556735] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.556757] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.556801] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.556822] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.556843] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.556862] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.556866] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 7.556875] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 7.566806] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 7.566817] ath10k_pci 0000:0b:00.0: boot target initialised
[ 7.584709] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.584733] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.584753] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.584775] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.584819] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.584840] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.584861] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.584881] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.584885] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 7.584893] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 7.594824] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 7.594836] ath10k_pci 0000:0b:00.0: boot target initialised
[ 7.594839] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 7.594861] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.594881] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.594900] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.594921] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.594958] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.594977] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.594998] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.595017] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.595095] ath10k_pci 0000:0b:00.0: boot chip reset complete (warm)
[ 7.595143] ath10k_pci 0000:0b:00.0: boot hif power up
[ 7.595159] ath10k_pci 0000:0b:00.0: boot 988x chip reset
[ 7.595163] ath10k_pci 0000:0b:00.0: boot warm reset
[ 7.632646] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.632678] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.632698] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.632720] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.632764] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.632786] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.632807] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.632826] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.632831] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 7.632839] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 7.642771] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 7.642781] ath10k_pci 0000:0b:00.0: boot target initialised
[ 7.660475] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.660498] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.660519] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.660540] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.660590] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.660610] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.660632] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.660652] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.660656] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 7.660664] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 7.670593] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 7.670601] ath10k_pci 0000:0b:00.0: boot target initialised
[ 7.670603] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 7.670621] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.670638] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.670654] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.670672] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.670698] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.670715] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.670733] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.670748] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.670815] ath10k_pci 0000:0b:00.0: boot chip reset complete (warm)
[ 7.670833] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 7.670849] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 7.670865] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 7.670883] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 7.670910] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 7.670926] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 7.670944] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 7.670960] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 7.671795] ath10k_pci 0000:0b:00.0: Hardware name qca988x hw2.0 version 0x4100016c
[ 7.674687] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/pre-cal-pci-0000:0b:00.0.bin': -12
[ 7.675051] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/cal-pci-0000:0b:00.0.bin': 0
[ 7.675054] ath10k_pci 0000:0b:00.0: found calibration file ath10k/cal-pci-0000:0b:00.0.bin
[ 7.675057] ath10k_pci 0000:0b:00.0: trying fw api 6
[ 7.678199] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/firmware-6.bin': -12
[ 7.678202] ath10k_pci 0000:0b:00.0: trying fw api 5
[ 7.680560] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/firmware-5.bin': 0
[ 7.680563] ath10k_pci 0000:0b:00.0: found fw version 10.2.4-1.0-00047
[ 7.680565] ath10k_pci 0000:0b:00.0: found fw timestamp 1565675359
[ 7.680568] ath10k_pci 0000:0b:00.0: found otp image ie (7221 B)
[ 7.680570] ath10k_pci 0000:0b:00.0: found fw image ie (241717 B)
[ 7.680572] ath10k_pci 0000:0b:00.0: found firmware features ie (3 B)
[ 7.680575] ath10k_pci 0000:0b:00.0: Enabling feature bit: 3
[ 7.680577] ath10k_pci 0000:0b:00.0: Enabling feature bit: 10
[ 7.680579] ath10k_pci 0000:0b:00.0: Enabling feature bit: 12
[ 7.680581] ath10k_pci 0000:0b:00.0: Enabling feature bit: 16
[ 7.680583] ath10k_pci 0000:0b:00.0: features
[ 7.680587] ath10k_pci 0000:0b:00.0: 00000000: 08 14 01 00 00 00 00 00 ........
[ 7.680589] ath10k_pci 0000:0b:00.0: found fw ie wmi op version 5
[ 7.680591] ath10k_pci 0000:0b:00.0: found fw ie htt op version 2
[ 7.680594] ath10k_pci 0000:0b:00.0: using fw api 5
[ 7.680599] ath10k_pci 0000:0b:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 7.682217] ath10k_pci 0000:0b:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 7.684919] ath10k_pci 0000:0b:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[ 7.687907] ath10k_pci 0000:0b:00.0: boot did not find a pre calibration file, try DT next: -12
[ 7.687910] ath10k_pci 0000:0b:00.0: unable to load pre cal data from DT: -2
[ 7.687912] ath10k_pci 0000:0b:00.0: could not load pre cal data: -2
[ 7.687915] ath10k_pci 0000:0b:00.0: boot upload otp to 0x1234 len 7221 for board id
[ 7.721044] ath10k_pci 0000:0b:00.0: boot get otp board id result 0x00000001 board_id 0 chip_id 0 ext_bid_support 0
[ 7.721045] ath10k_pci 0000:0b:00.0: board id does not exist in otp, ignore it
[ 7.721066] ath10k_pci 0000:0b:00.0: SMBIOS bdf variant name not set.
[ 7.721068] ath10k_pci 0000:0b:00.0: DT bdf variant name not set.
[ 7.721070] ath10k_pci 0000:0b:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
[ 7.721073] ath10k_pci 0000:0b:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
[ 7.723002] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/board-2.bin': -12
[ 7.723280] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/board.bin': 0
[ 7.723282] ath10k_pci 0000:0b:00.0: using board api 1
[ 7.723291] ath10k_pci 0000:0b:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 7.724754] ath10k_pci 0000:0b:00.0: boot did not find a pre calibration file, try DT next: -12
[ 7.724756] ath10k_pci 0000:0b:00.0: unable to load pre cal data from DT: -2
[ 7.724757] ath10k_pci 0000:0b:00.0: failed to load pre cal data: -2
[ 7.724759] ath10k_pci 0000:0b:00.0: pre cal download procedure failed, try cal file: -2
[ 7.724817] ath10k_pci 0000:0b:00.0: boot push board extended data addr 0x0
[ 7.728985] ath10k_pci 0000:0b:00.0: boot cal file downloaded
[ 7.728987] ath10k_pci 0000:0b:00.0: boot using calibration mode file
[ 7.728989] ath10k_pci 0000:0b:00.0: boot uploading firmware image 00000000d24b1aac len 241717
[ 8.760104] ath10k_pci 0000:0b:00.0: boot htc service 'Control' ul pipe 0 dl pipe 1 eid 0 ready
[ 8.760106] ath10k_pci 0000:0b:00.0: boot htc service 'Control' eid 0 TX flow control disabled
[ 8.760127] ath10k_pci 0000:0b:00.0: htt tx max num pending tx 1424
[ 8.760155] ath10k_pci 0000:0b:00.0: htt rx ring size 2048 fill_level 1023
[ 8.760157] ath10k_pci 0000:0b:00.0: boot hif start
[ 8.763165] ath10k_pci 0000:0b:00.0: boot htc service HTT Data does not allocate target credits
[ 8.763277] ath10k_pci 0000:0b:00.0: boot htc service 'HTT Data' ul pipe 4 dl pipe 5 eid 1 ready
[ 8.763279] ath10k_pci 0000:0b:00.0: boot htc service 'HTT Data' eid 1 TX flow control disabled
[ 8.763359] ath10k_pci 0000:0b:00.0: boot htc service 'WMI' ul pipe 3 dl pipe 2 eid 2 ready
[ 8.763361] ath10k_pci 0000:0b:00.0: unsupported HTC pktlog service id: 1536
[ 8.763533] ath10k_pci 0000:0b:00.0: firmware 10.2.4-1.0-00047 booted
[ 8.782957] ath10k_pci 0000:0b:00.0: htt target version 2.1
[ 8.782974] ath10k_pci 0000:0b:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 8.786615] ath10k_pci 0000:0b:00.0: boot suspend complete
[ 8.786642] ath10k_pci 0000:0b:00.0: boot hif stop
[ 8.786701] ath10k_pci 0000:0b:00.0: boot warm reset
[ 8.824677] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 8.824699] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 8.824718] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 8.824738] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 8.824780] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 8.824799] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 8.824820] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 8.824837] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 8.824841] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 8.824849] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 8.834781] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 8.834793] ath10k_pci 0000:0b:00.0: boot target initialised
[ 8.852705] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000a38ddbc2
[ 8.852732] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 0000000017294974
[ 8.852755] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr 0000000079a9412a
[ 8.852781] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr 000000007463b3d8
[ 8.852832] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 0000000093c9915f
[ 8.852857] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 00000000c880fb11
[ 8.852882] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 000000009da8e171
[ 8.852904] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr 0000000023867065
[ 8.852909] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 8.852917] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 8.862849] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 8.862861] ath10k_pci 0000:0b:00.0: boot target initialised
[ 8.862865] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 8.864399] ath10k_pci 0000:0b:00.0: boot hif power down
[ 8.864421] ath10k_pci 0000:0b:00.0: failed to get wrd method 5
[ 8.864425] ath10k_pci 0000:0b:00.0: fallback to eeprom programmed regulatory settings
[ 8.864429] ath: EEPROM regdomain sanitized
[ 8.864431] ath: EEPROM regdomain: 0x64
[ 8.864433] ath: EEPROM indicates we should expect a direct regpair map
[ 8.864438] ath: Country alpha2 being used: 00
[ 8.864440] ath: Regpair used: 0x64
[ 8.864892] ath10k_pci 0000:0b:00.0: dfs region 0x0
[ 8.867495] ath10k_pci 0000:0c:00.0: pci probe 168c:003c 0000:0000
[ 8.867732] ath10k_pci 0000:0c:00.0: boot pci_mem 0x000000006d51a418
[ 8.867964] ath10k_pci 0000:0c:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 8.869495] ath10k_pci 0000:0c:00.0: boot 988x chip reset
[ 8.869497] ath10k_pci 0000:0c:00.0: boot warm reset
[ 8.908391] ath10k_pci 0000:0c:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000c7600c39
[ 8.908409] ath10k_pci 0000:0c:00.0: boot ce dest ring id 1 entries 512 base_addr 00000000c553993c
[ 8.908431] ath10k_pci 0000:0c:00.0: boot ce dest ring id 2 entries 128 base_addr 000000006092aa2c
[ 8.908456] ath10k_pci 0000:0c:00.0: boot init ce src ring id 3 entries 32 base_addr 0000000035680912
[ 8.908491] ath10k_pci 0000:0c:00.0: boot init ce src ring id 4 entries 8192 base_addr 00000000b1d40145
[ 8.908508] ath10k_pci 0000:0c:00.0: boot ce dest ring id 5 entries 512 base_addr 0000000067a72128
[ 8.908526] ath10k_pci 0000:0c:00.0: boot init ce src ring id 7 entries 2 base_addr 00000000e373ee5e
[ 8.908542] ath10k_pci 0000:0c:00.0: boot ce dest ring id 7 entries 2 base_addr 00000000a2a98082
[ 8.908545] ath10k_pci 0000:0c:00.0: boot waiting target to initialise
[ 8.908550] ath10k_pci 0000:0c:00.0: boot target indicator 0
[ 8.918478] ath10k_pci 0000:0c:00.0: boot target indicator 2
[ 8.918488] ath10k_pci 0000:0c:00.0: boot target initialised
[ 8.936705] ath10k_pci 0000:0c:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000c7600c39
[ 8.936728] ath10k_pci 0000:0c:00.0: boot ce dest ring id 1 entries 512 base_addr 00000000c553993c
[ 8.936748] ath10k_pci 0000:0c:00.0: boot ce dest ring id 2 entries 128 base_addr 000000006092aa2c
[ 8.936769] ath10k_pci 0000:0c:00.0: boot init ce src ring id 3 entries 32 base_addr 0000000035680912
[ 8.936812] ath10k_pci 0000:0c:00.0: boot init ce src ring id 4 entries 8192 base_addr 00000000b1d40145
[ 8.936833] ath10k_pci 0000:0c:00.0: boot ce dest ring id 5 entries 512 base_addr 0000000067a72128
[ 8.936854] ath10k_pci 0000:0c:00.0: boot init ce src ring id 7 entries 2 base_addr 00000000e373ee5e
[ 8.936873] ath10k_pci 0000:0c:00.0: boot ce dest ring id 7 entries 2 base_addr 00000000a2a98082
[ 8.936878] ath10k_pci 0000:0c:00.0: boot waiting target to initialise
[ 8.936886] ath10k_pci 0000:0c:00.0: boot target indicator 0
[ 8.946817] ath10k_pci 0000:0c:00.0: boot target indicator 2
[ 8.946828] ath10k_pci 0000:0c:00.0: boot target initialised
[ 8.946832] ath10k_pci 0000:0c:00.0: boot warm reset complete
[ 8.946853] ath10k_pci 0000:0c:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000c7600c39
[ 8.946873] ath10k_pci 0000:0c:00.0: boot ce dest ring id 1 entries 512 base_addr 00000000c553993c
[ 8.946892] ath10k_pci 0000:0c:00.0: boot ce dest ring id 2 entries 128 base_addr 000000006092aa2c
[ 8.946913] ath10k_pci 0000:0c:00.0: boot init ce src ring id 3 entries 32 base_addr 0000000035680912
[ 8.946950] ath10k_pci 0000:0c:00.0: boot init ce src ring id 4 entries 8192 base_addr 00000000b1d40145
[ 8.946970] ath10k_pci 0000:0c:00.0: boot ce dest ring id 5 entries 512 base_addr 0000000067a72128
[ 8.946991] ath10k_pci 0000:0c:00.0: boot init ce src ring id 7 entries 2 base_addr 00000000e373ee5e
[ 8.947009] ath10k_pci 0000:0c:00.0: boot ce dest ring id 7 entries 2 base_addr 00000000a2a98082
[ 8.947086] ath10k_pci 0000:0c:00.0: boot chip reset complete (warm)
[ 8.947136] ath10k_pci 0000:0c:00.0: boot hif power up
[ 8.947152] ath10k_pci 0000:0c:00.0: boot 988x chip reset
[
[ 9.024073] ath10k_pci 0000:0c:00.0: Hardware name qca988x hw2.0 version 0x4100016c
[ 9.027133] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/pre-cal-pci-0000:0c:00.0.bin': -12
[ 9.027491] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/cal-pci-0000:0c:00.0.bin': 0
[ 9.027493] ath10k_pci 0000:0c:00.0: found calibration file ath10k/cal-pci-0000:0c:00.0.bin
[ 9.027496] ath10k_pci 0000:0c:00.0: trying fw api 6
[ 9.029393] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/QCA988X/hw2.0/firmware-6.bin': -12
[ 9.029395] ath10k_pci 0000:0c:00.0: trying fw api 5
[ 9.029398] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/QCA988X/hw2.0/firmware-5.bin': 0
[ 9.029400] ath10k_pci 0000:0c:00.0: found fw version 10.2.4-1.0-00047
[ 9.029402] ath10k_pci 0000:0c:00.0: found fw timestamp 1565675359
[ 9.029404] ath10k_pci 0000:0c:00.0: found otp image ie (7221 B)
[ 9.029405] ath10k_pci 0000:0c:00.0: found fw image ie (241717 B)
[ 9.029407] ath10k_pci 0000:0c:00.0: found firmware features ie (3 B)
[ 9.029409] ath10k_pci 0000:0c:00.0: Enabling feature bit: 3
[ 9.029410] ath10k_pci 0000:0c:00.0: Enabling feature bit: 10
[ 9.029412] ath10k_pci 0000:0c:00.0: Enabling feature bit: 12
[ 9.029413] ath10k_pci 0000:0c:00.0: Enabling feature bit: 16
[ 9.029414] ath10k_pci 0000:0c:00.0: features
[ 9.029417] ath10k_pci 0000:0c:00.0: 00000000: 08 14 01 00 00 00 00 00 ........
[ 9.029418] ath10k_pci 0000:0c:00.0: found fw ie wmi op version 5
[ 9.029420] ath10k_pci 0000:0c:00.0: found fw ie htt op version 2
[ 9.029421] ath10k_pci 0000:0c:00.0: using fw api 5
[ 9.029425] ath10k_pci 0000:0c:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 9.030786] ath10k_pci 0000:0c:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 9.032869] ath10k_pci 0000:0c:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[ 9.035349] ath10k_pci 0000:0c:00.0: boot did not find a pre calibration file, try DT next: -12
[ 9.035351] ath10k_pci 0000:0c:00.0: unable to load pre cal data from DT: -2
[ 9.035352] ath10k_pci 0000:0c:00.0: could not load pre cal data: -2
[ 9.035354] ath10k_pci 0000:0c:00.0: boot upload otp to 0x1234 len 7221 for board id
[ 9.068488] ath10k_pci 0000:0c:00.0: boot get otp board id result 0x00000001 board_id 0 chip_id 0 ext_bid_support 0
[ 9.068489] ath10k_pci 0000:0c:00.0: board id does not exist in otp, ignore it
[ 9.068514] ath10k_pci 0000:0c:00.0: SMBIOS bdf variant name not set.
[ 9.068516] ath10k_pci 0000:0c:00.0: DT bdf variant name not set.
[ 9.068520] ath10k_pci 0000:0c:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
[ 9.068522] ath10k_pci 0000:0c:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
[ 9.070347] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/QCA988X/hw2.0/board-2.bin': -12
[ 9.070350] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/QCA988X/hw2.0/board.bin': 0
[ 9.070351] ath10k_pci 0000:0c:00.0: using board api 1
[ 9.070371] ath10k_pci 0000:0c:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 9.071962] ath10k_pci 0000:0c:00.0: boot did not find a pre calibration file, try DT next: -12
[ 9.071964] ath10k_pci 0000:0c:00.0: unable to load pre cal data from DT: -2
[ 9.071966] ath10k_pci 0000:0c:00.0: failed to load pre cal data: -2
[ 9.071967] ath10k_pci 0000:0c:00.0: pre cal download procedure failed, try cal file: -2
[ 9.072010] ath10k_pci 0000:0c:00.0: boot push board extended data addr 0x0
[ 9.076134] ath10k_pci 0000:0c:00.0: boot cal file downloaded
[ 9.076136] ath10k_pci 0000:0c:00.0: boot using calibration mode file
[ 9.076139] ath10k_pci 0000:0c:00.0: boot uploading firmware image 00000000d24b1aac len 241717
[ 10.107324] ath10k_pci 0000:0c:00.0: boot htc service 'Control' ul pipe 0 dl pipe 1 eid 0 ready
[ 10.107326] ath10k_pci 0000:0c:00.0: boot htc service 'Control' eid 0 TX flow control disabled
[ 10.107347] ath10k_pci 0000:0c:00.0: htt tx max num pending tx 1424
[ 10.107372] ath10k_pci 0000:0c:00.0: htt rx ring size 2048 fill_level 1023
[ 10.107374] ath10k_pci 0000:0c:00.0: boot hif start
[ 10.110347] ath10k_pci 0000:0c:00.0: boot htc service HTT Data does not allocate target credits
[ 10.110402] ath10k_pci 0000:0c:00.0: boot htc service 'HTT Data' ul pipe 4 dl pipe 5 eid 1 ready
[ 10.110403] ath10k_pci 0000:0c:00.0: boot htc service 'HTT Data' eid 1 TX flow control disabled
[ 10.110454] ath10k_pci 0000:0c:00.0: boot htc service 'WMI' ul pipe 3 dl pipe 2 eid 2 ready
[ 10.110457] ath10k_pci 0000:0c:00.0: unsupported HTC pktlog service id: 1536
[ 10.110593] ath10k_pci 0000:0c:00.0: firmware 10.2.4-1.0-00047 booted
[ 10.131383] ath10k_pci 0000:0c:00.0: htt target version 2.1
[ 10.131399] ath10k_pci 0000:0c:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 10.135316] ath10k_pci 0000:0c:00.0: boot suspend complete
[ 10.135326] ath10k_pci 0000:0c:00.0: boot hif stop
[ 10.135385] ath10k_pci 0000:0c:00.0: boot warm reset
[ 10.172505] ath10k_pci 0000:0c:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000c7600c39
[ 10.172538] ath10k_pci 0000:0c:00.0: boot ce dest ring id 1 entries 512 base_addr 00000000c553993c
[ 10.172552] ath10k_pci 0000:0c:00.0: boot ce dest ring id 2 entries 128 base_addr 000000006092aa2c
[ 10.172569] ath10k_pci 0000:0c:00.0: boot init ce src ring id 3 entries 32 base_addr 0000000035680912
[ 10.172597] ath10k_pci 0000:0c:00.0: boot init ce src ring id 4 entries 8192 base_addr 00000000b1d40145
[ 10.172612] ath10k_pci 0000:0c:00.0: boot ce dest ring id 5 entries 512 base_addr 0000000067a72128
[ 10.172628] ath10k_pci 0000:0c:00.0: boot init ce src ring id 7 entries 2 base_addr 00000000e373ee5e
[ 10.172643] ath10k_pci 0000:0c:00.0: boot ce dest ring id 7 entries 2 base_addr 00000000a2a98082
[ 10.172645] ath10k_pci 0000:0c:00.0: boot waiting target to initialise
[ 10.172650] ath10k_pci 0000:0c:00.0: boot target indicator 0
[ 10.182578] ath10k_pci 0000:0c:00.0: boot target indicator 2
[ 10.182588] ath10k_pci 0000:0c:00.0: boot target initialised
[ 10.200486] ath10k_pci 0000:0c:00.0: boot init ce src ring id 0 entries 16 base_addr 00000000c7600c39
[ 10.200510] ath10k_pci 0000:0c:00.0: boot ce dest ring id 1 entries 512 base_addr 00000000c553993c
[ 10.200532] ath10k_pci 0000:0c:00.0: boot ce dest ring id 2 entries 128 base_addr 000000006092aa2c
[ 10.200557] ath10k_pci 0000:0c:00.0: boot init ce src ring id 3 entries 32 base_addr 0000000035680912
[ 10.200597] ath10k_pci 0000:0c:00.0: boot init ce src ring id 4 entries 8192 base_addr 00000000b1d40145
[ 10.200620] ath10k_pci 0000:0c:00.0: boot ce dest ring id 5 entries 512 base_addr 0000000067a72128
[ 10.200645] ath10k_pci 0000:0c:00.0: boot init ce src ring id 7 entries 2 base_addr 00000000e373ee5e
[ 10.200667] ath10k_pci 0000:0c:00.0: boot ce dest ring id 7 entries 2 base_addr 00000000a2a98082
[ 10.200671] ath10k_pci 0000:0c:00.0: boot waiting target to initialise
[ 10.200679] ath10k_pci 0000:0c:00.0: boot target indicator 0
[ 10.210610] ath10k_pci 0000:0c:00.0: boot target indicator 2
[ 10.210622] ath10k_pci 0000:0c:00.0: boot target initialised
[ 10.210625] ath10k_pci 0000:0c:00.0: boot warm reset complete
[ 10.212172] ath10k_pci 0000:0c:00.0: boot hif power down
[ 10.212197] ath10k_pci 0000:0c:00.0: failed to get wrd method 5
[ 10.212201] ath10k_pci 0000:0c:00.0: fallback to eeprom programmed regulatory settings
[ 10.212204] ath: EEPROM regdomain sanitized
[ 10.212207] ath: EEPROM regdomain: 0x64
[ 10.212208] ath: EEPROM indicates we should expect a direct regpair map
[ 10.212213] ath: Country alpha2 being used: 00
[ 10.212215] ath: Regpair used: 0x64
[ 10.212688] ath10k_pci 0000:0c:00.0: dfs region 0x0
[ 10.221584] batman_adv: B.A.T.M.A.N. advanced 2021.0-openwrt-1 (compatibility version 15) loaded
here is another one
10.723014] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[ 10.725697] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[ 10.733480] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 10.736052] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 10.739003] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to simplified (2000-8000 ints) mode
[ 10.741780] e1000e 0000:00:19.0: Interrupt Mode set to 1
[ 10.913381] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:2
[ 10.918681] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 10.923846] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[ 10.934932] usbcore: registered new interface driver ums-alauda
[ 10.937938] usbcore: registered new interface driver ums-cypress
[ 10.940811] usbcore: registered new interface driver ums-datafab
[ 10.942932] usbcore: registered new interface driver ums-freecom
[ 10.944978] usbcore: registered new interface driver ums-isd200
[ 10.947166] usbcore: registered new interface driver ums-jumpshot
[ 10.949201] usbcore: registered new interface driver ums-karma
[ 10.952125] usbcore: registered new interface driver ums-sddr09
[ 10.954173] usbcore: registered new interface driver ums-sddr55
[ 10.956600] usbcore: registered new interface driver ums-usbat
[ 10.963768] xt_time: kernel timezone is -0000
[ 11.093088] PPP generic driver version 2.4.2
[ 11.095777] NET: Registered protocol family 24
[ 11.132915] ath10k_pci 0000:0b:00.0: pci probe 168c:003c 0000:0000
[ 11.133118] ath10k_pci 0000:0b:00.0: boot pci_mem 0x6f5310d3
[ 11.135454] ath10k_pci 0000:0b:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.137911] ath10k_pci 0000:0b:00.0: boot 988x chip reset
[ 11.137913] ath10k_pci 0000:0b:00.0: boot warm reset
[ 11.175376] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.175398] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.175418] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.175441] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.175485] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.175506] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.175527] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.175546] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.175551] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 11.175559] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 11.185491] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 11.185502] ath10k_pci 0000:0b:00.0: boot target initialised
[ 11.203387] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.203410] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.203429] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.203451] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.203499] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.203520] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.203541] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.203560] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.203568] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 11.203575] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 11.213507] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 11.213518] ath10k_pci 0000:0b:00.0: boot target initialised
[ 11.213522] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 11.213545] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.213565] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.213584] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.213605] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.213643] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.213663] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.213685] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.213703] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.213782] ath10k_pci 0000:0b:00.0: boot chip reset complete (warm)
[ 11.213827] ath10k_pci 0000:0b:00.0: boot hif power up
[ 11.213843] ath10k_pci 0000:0b:00.0: boot 988x chip reset
[ 11.213847] ath10k_pci 0000:0b:00.0: boot warm reset
[ 11.251409] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.251437] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.251457] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.251479] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.251526] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.251547] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.251569] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.251588] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.251592] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 11.251601] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 11.261532] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 11.261543] ath10k_pci 0000:0b:00.0: boot target initialised
[ 11.279435] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.279458] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.279478] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.279500] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.279544] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.279565] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.279587] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.279606] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.279611] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 11.279619] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 11.289550] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 11.289560] ath10k_pci 0000:0b:00.0: boot target initialised
[ 11.289564] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 11.289587] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.289607] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.289626] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.289648] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.289685] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.289705] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.289727] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.289746] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.289822] ath10k_pci 0000:0b:00.0: boot chip reset complete (warm)
[ 11.289843] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 11.289863] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 11.289883] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 11.289904] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 11.289941] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 11.289961] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 11.289983] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 11.290002] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 11.290872] ath10k_pci 0000:0b:00.0: Hardware name qca988x hw2.0 version 0x4100016c
[ 11.294601] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/pre-cal-pci-0000:0b:00.0.bin': -12
[ 11.295913] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/cal-pci-0000:0b:00.0.bin': 0
[ 11.295921] ath10k_pci 0000:0b:00.0: found calibration file ath10k/cal-pci-0000:0b:00.0.bin
[ 11.295923] ath10k_pci 0000:0b:00.0: trying fw api 6
[ 11.300517] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/firmware-6.bin': -12
[ 11.300518] ath10k_pci 0000:0b:00.0: trying fw api 5
[ 11.332684] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/firmware-5.bin': 0
[ 11.332691] ath10k_pci 0000:0b:00.0: found fw version 10.2.4-1.0-00047
[ 11.332697] ath10k_pci 0000:0b:00.0: found fw timestamp 1565675359
[ 11.332702] ath10k_pci 0000:0b:00.0: found otp image ie (7221 B)
[ 11.332706] ath10k_pci 0000:0b:00.0: found fw image ie (241717 B)
[ 11.332711] ath10k_pci 0000:0b:00.0: found firmware features ie (3 B)
[ 11.332715] ath10k_pci 0000:0b:00.0: Enabling feature bit: 3
[ 11.332720] ath10k_pci 0000:0b:00.0: Enabling feature bit: 10
[ 11.332724] ath10k_pci 0000:0b:00.0: Enabling feature bit: 12
[ 11.332728] ath10k_pci 0000:0b:00.0: Enabling feature bit: 16
[ 11.332732] ath10k_pci 0000:0b:00.0: features
[ 11.332739] ath10k_pci 0000:0b:00.0: 00000000: 08 14 01 00 ....
[ 11.332744] ath10k_pci 0000:0b:00.0: found fw ie wmi op version 5
[ 11.332748] ath10k_pci 0000:0b:00.0: found fw ie htt op version 2
[ 11.332760] ath10k_pci 0000:0b:00.0: using fw api 5
[ 11.332771] ath10k_pci 0000:0b:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 11.337431] ath10k_pci 0000:0b:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 11.344377] ath10k_pci 0000:0b:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[ 11.349451] ath10k_pci 0000:0b:00.0: boot did not find a pre calibration file, try DT next: -12
[ 11.349455] ath10k_pci 0000:0b:00.0: unable to load pre cal data from DT: -2
[ 11.349460] ath10k_pci 0000:0b:00.0: could not load pre cal data: -2
[ 11.349466] ath10k_pci 0000:0b:00.0: boot upload otp to 0x1234 len 7221 for board id
[ 11.382611] ath10k_pci 0000:0b:00.0: boot get otp board id result 0x00000001 board_id 0 chip_id 0 ext_bid_support 0
[ 11.382613] ath10k_pci 0000:0b:00.0: board id does not exist in otp, ignore it
[ 11.382643] ath10k_pci 0000:0b:00.0: SMBIOS bdf variant name not set.
[ 11.382645] ath10k_pci 0000:0b:00.0: DT bdf variant name not set.
[ 11.382648] ath10k_pci 0000:0b:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
[ 11.382651] ath10k_pci 0000:0b:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
[ 11.385028] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/board-2.bin': -12
[ 11.386268] ath10k_pci 0000:0b:00.0: boot fw request 'ath10k/QCA988X/hw2.0/board.bin': 0
[ 11.386270] ath10k_pci 0000:0b:00.0: using board api 1
[ 11.386280] ath10k_pci 0000:0b:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 11.388459] ath10k_pci 0000:0b:00.0: boot did not find a pre calibration file, try DT next: -12
[ 11.388460] ath10k_pci 0000:0b:00.0: unable to load pre cal data from DT: -2
[ 11.388462] ath10k_pci 0000:0b:00.0: failed to load pre cal data: -2
[ 11.388463] ath10k_pci 0000:0b:00.0: pre cal download procedure failed, try cal file: -2
[ 11.388520] ath10k_pci 0000:0b:00.0: boot push board extended data addr 0x0
[ 11.392688] ath10k_pci 0000:0b:00.0: boot cal file downloaded
[ 11.392690] ath10k_pci 0000:0b:00.0: boot using calibration mode file
[ 11.392695] ath10k_pci 0000:0b:00.0: boot uploading firmware image f23be241 len 241717
[ 12.424103] ath10k_pci 0000:0b:00.0: boot htc service 'Control' ul pipe 0 dl pipe 1 eid 0 ready
[ 12.424105] ath10k_pci 0000:0b:00.0: boot htc service 'Control' eid 0 TX flow control disabled
[ 12.424144] ath10k_pci 0000:0b:00.0: htt tx max num pending tx 1424
[ 12.424167] ath10k_pci 0000:0b:00.0: htt rx ring size 2048 fill_level 1023
[ 12.424169] ath10k_pci 0000:0b:00.0: boot hif start
[ 12.427169] ath10k_pci 0000:0b:00.0: boot htc service HTT Data does not allocate target credits
[ 12.427227] ath10k_pci 0000:0b:00.0: boot htc service 'HTT Data' ul pipe 4 dl pipe 5 eid 1 ready
[ 12.427229] ath10k_pci 0000:0b:00.0: boot htc service 'HTT Data' eid 1 TX flow control disabled
[ 12.427287] ath10k_pci 0000:0b:00.0: boot htc service 'WMI' ul pipe 3 dl pipe 2 eid 2 ready
[ 12.427289] ath10k_pci 0000:0b:00.0: unsupported HTC pktlog service id: 1536
[ 12.427409] ath10k_pci 0000:0b:00.0: firmware 10.2.4-1.0-00047 booted
[ 12.448538] ath10k_pci 0000:0b:00.0: htt target version 2.1
[ 12.448557] ath10k_pci 0000:0b:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 12.453909] ath10k_pci 0000:0b:00.0: boot suspend complete
[ 12.453941] ath10k_pci 0000:0b:00.0: boot hif stop
[ 12.454002] ath10k_pci 0000:0b:00.0: boot warm reset
[ 12.491371] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 12.491396] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 12.491414] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 12.491434] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 12.491477] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 12.491496] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 12.491516] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 12.491533] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 12.491538] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 12.491546] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 12.501478] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 12.501490] ath10k_pci 0000:0b:00.0: boot target initialised
[ 12.519407] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 12.519433] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 12.519456] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 12.519482] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 12.519530] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 12.519555] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 12.519580] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 12.519602] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 12.519607] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 12.519615] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 12.529547] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 12.529559] ath10k_pci 0000:0b:00.0: boot target initialised
[ 12.529563] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 12.531115] ath10k_pci 0000:0b:00.0: boot hif power down
[ 12.531142] ath10k_pci 0000:0b:00.0: failed to get wrd method 5
[ 12.531147] ath10k_pci 0000:0b:00.0: fallback to eeprom programmed regulatory settings
[ 12.531150] ath: EEPROM regdomain sanitized
[ 12.531152] ath: EEPROM regdomain: 0x64
[ 12.531154] ath: EEPROM indicates we should expect a direct regpair map
[ 12.531159] ath: Country alpha2 being used: 00
[ 12.531161] ath: Regpair used: 0x64
[ 12.531700] ath10k_pci 0000:0b:00.0: dfs region 0x0
[ 12.536882] batman_adv: B.A.T.M.A.N. advanced 2021.0-openwrt-1 (compatibility version 15) loaded
[ 12.541557] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 13.960272] br-lan: port 1(eth0) entered blocking state
[ 13.965126] br-lan: port 1(eth0) entered disabled state
[ 13.969961] device eth0 entered promiscuous mode
[ 14.286578] ath10k_pci 0000:0b:00.0: boot hif power up
[ 14.286591] ath10k_pci 0000:0b:00.0: boot 988x chip reset
[ 14.286593] ath10k_pci 0000:0b:00.0: boot warm reset
[ 14.323125] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 14.323146] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 14.323165] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 14.323188] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 14.323239] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 14.323258] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 14.323279] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 14.323297] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 14.323299] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 14.323304] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 14.333230] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 14.333239] ath10k_pci 0000:0b:00.0: boot target initialised
[ 14.351349] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 14.351379] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 14.351403] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 14.351429] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 14.351478] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 14.351508] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 14.351533] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 14.351555] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 14.351560] ath10k_pci 0000:0b:00.0: boot waiting target to initialise
[ 14.351569] ath10k_pci 0000:0b:00.0: boot target indicator 0
[ 14.361501] ath10k_pci 0000:0b:00.0: boot target indicator 2
[ 14.361514] ath10k_pci 0000:0b:00.0: boot target initialised
[ 14.361518] ath10k_pci 0000:0b:00.0: boot warm reset complete
[ 14.361545] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 14.361570] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 14.361592] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 14.361618] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 14.361659] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 14.361682] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 14.361708] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 14.361730] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 14.361807] ath10k_pci 0000:0b:00.0: boot chip reset complete (warm)
[ 14.361833] ath10k_pci 0000:0b:00.0: boot init ce src ring id 0 entries 16 base_addr 08b1156f
[ 14.361856] ath10k_pci 0000:0b:00.0: boot ce dest ring id 1 entries 512 base_addr 2f667780
[ 14.361879] ath10k_pci 0000:0b:00.0: boot ce dest ring id 2 entries 128 base_addr bcb0fa3c
[ 14.361904] ath10k_pci 0000:0b:00.0: boot init ce src ring id 3 entries 32 base_addr dbf61770
[ 14.361945] ath10k_pci 0000:0b:00.0: boot init ce src ring id 4 entries 8192 base_addr 8278ceca
[ 14.361968] ath10k_pci 0000:0b:00.0: boot ce dest ring id 5 entries 512 base_addr 50ae2def
[ 14.361994] ath10k_pci 0000:0b:00.0: boot init ce src ring id 7 entries 2 base_addr 42534532
[ 14.362016] ath10k_pci 0000:0b:00.0: boot ce dest ring id 7 entries 2 base_addr e3cf6bd9
[ 14.363415] ath10k_pci 0000:0b:00.0: boot did not find a pre calibration file, try DT next: -12
[ 14.363418] ath10k_pci 0000:0b:00.0: unable to load pre cal data from DT: -2
[ 14.363420] ath10k_pci 0000:0b:00.0: failed to load pre cal data: -2
[ 14.363423] ath10k_pci 0000:0b:00.0: pre cal download procedure failed, try cal file: -2
[ 14.363487] ath10k_pci 0000:0b:00.0: boot push board extended data addr 0x0
[ 14.367716] ath10k_pci 0000:0b:00.0: boot cal file downloaded
[ 14.367719] ath10k_pci 0000:0b:00.0: boot using calibration mode file
[ 14.367724] ath10k_pci 0000:0b:00.0: boot uploading firmware image f23be241 len 241717
[ 15.404143] ath10k_pci 0000:0b:00.0: boot htc service 'Control' ul pipe 0 dl pipe 1 eid 0 ready
[ 15.404145] ath10k_pci 0000:0b:00.0: boot htc service 'Control' eid 0 TX flow control disabled
[ 15.404164] ath10k_pci 0000:0b:00.0: htt tx max num pending tx 1424
[ 15.404171] ath10k_pci 0000:0b:00.0: htt rx ring size 2048 fill_level 1023
[ 15.404173] ath10k_pci 0000:0b:00.0: boot hif start
[ 15.407195] ath10k_pci 0000:0b:00.0: boot htc service HTT Data does not allocate target credits
[ 15.407252] ath10k_pci 0000:0b:00.0: boot htc service 'HTT Data' ul pipe 4 dl pipe 5 eid 1 ready
[ 15.407254] ath10k_pci 0000:0b:00.0: boot htc service 'HTT Data' eid 1 TX flow control disabled
[ 15.407308] ath10k_pci 0000:0b:00.0: boot htc service 'WMI' ul pipe 3 dl pipe 2 eid 2 ready
[ 15.407311] ath10k_pci 0000:0b:00.0: unsupported HTC pktlog service id: 1536
[ 15.407403] ath10k_pci 0000:0b:00.0: firmware 10.2.4-1.0-00047 booted
[ 15.428402] ath10k_pci 0000:0b:00.0: htt target version 2.1
[ 15.428510] ath10k_pci 0000:0b:00.0: pdev param 0 not supported by firmware
[ 15.446276] ath10k_pci 0000:0b:00.0: mac create vdev 0 map ffff
[ 15.446285] ath10k_pci 0000:0b:00.0: mac vdev create 0 (add interface) type 1 subtype 0 bcnmode single-buf
[ 15.446665] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.446670] ath10k_pci 0000:0b:00.0: mac vdev 0 recalc rts/cts prot 17
[ 15.446702] ath10k_pci 0000:0b:00.0: defer cts setup, vdev is not ready yet
[ 15.446705] ath10k_pci 0000:0b:00.0: mac vdev 0 slot_time 1
[ 15.446709] ath10k_pci 0000:0b:00.0: mac vdev 0 preamble 1n
[ 15.446920] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.446994] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.448111] br-lan: port 2(wlan0) entered blocking state
[ 15.450608] br-lan: port 2(wlan0) entered disabled state
[ 15.453237] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.453260] device wlan0 entered promiscuous mode
[ 15.458130] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.760254] ath10k_pci 0000:0b:00.0: mac chanctx add freq 5180 width 3 ptr b217c2b0
[ 15.760264] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.760271] ath10k_pci 0000:0b:00.0: mac chanctx assign ptr b217c2b0 vdev_id 0
[ 15.760278] ath10k_pci 0000:0b:00.0: mac vdev 0 start center_freq 5180 phymode 11ac-vht80
[ 15.767547] ath10k_pci 0000:0b:00.0: mac vdev 0 cts_protection 0
[ 15.767556] ath10k_pci 0000:0b:00.0: mac vdev_id 0 txpower 20
[ 15.767558] ath10k_pci 0000:0b:00.0: mac txpower 20
[ 15.767630] ath10k_pci 0000:0b:00.0: mac chanctx change freq 5180 width 3 ptr b217c2b0 changed 2
[ 15.767690] ath10k_pci 0000:0b:00.0: mac vdev 0 beacon_interval 100
[ 15.767693] ath10k_pci 0000:0b:00.0: vdev 0 set beacon tx mode to staggered
[ 15.767798] ath10k_pci 0000:0b:00.0: mac vdev 0 dtim_period 2
[ 15.767876] ath10k_pci 0000:0b:00.0: mac vdev 0 up
[ 15.767878] ath10k_pci 0000:0b:00.0: mac vdev_id 0 txpower 20
[ 15.767880] ath10k_pci 0000:0b:00.0: mac txpower 20
[ 15.768057] ath10k_pci 0000:0b:00.0: mac vdev 0 recalc rts/cts prot 17
[ 15.768062] ath10k_pci 0000:0b:00.0: mac vdev 0 cts_protection 0
[ 15.768197] ath10k_pci 0000:0b:00.0: mac vdev 0 slot_time 2
[ 15.768200] ath10k_pci 0000:0b:00.0: mac vdev 0 preamble 2n
[ 15.768505] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.771192] br-lan: port 2(wlan0) entered blocking state
[ 15.773710] br-lan: port 2(wlan0) entered forwarding state
[ 15.776311] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 15.777747] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 16.292243] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 16.297384] br-lan: port 1(eth0) entered blocking state
[ 16.299872] br-lan: port 1(eth0) entered forwarding state
[ 16.935640] ath10k_pci 0000:0b:00.0: mac monitor recalc started? 0 needed? 0 allowed? 1
[ 21.760311] ath10k_pci 0000:0b:00.0: vdev 0 set beacon tx mode to staggered
[ 21.760327] ath10k_pci 0000:0b:00.0: mac vdev 0 dtim_period 2
[ 21.760526] ath10k_pci 0000:0b:00.0: mac vdev 0 recalc rts/cts prot 17
[ 21.760535] ath10k_pci 0000:0b:00.0: mac vdev 0 cts
hope someone with experience in ah10k sees this.
br.
Is this a pcie card out of a router (like a Archer C7v2) or something? The retail QCA9880 cards will have the caldata on the card itself. So no caldata file will be/is/should be necessary for retail QCA988X.
as for your question: In the provided log:
[ 9.027491] ath10k_pci 0000:0c:00.0: boot fw request 'ath10k/cal-pci-0000:0c:00.0.bin': 0
[ 9.027493] ath10k_pci 0000:0c:00.0: found calibration file ath10k/cal-pci-0000:0c:00.0.bin
the driver says here, that it found the provided calibration data.
Several options.
you can do it by patching the caldata (openwrt has a helper function in /lib/functions/caldata.sh called ath10k_patch_mac.
i.e.:
. /lib/functions/caldata.sh
ath10k_patch_mac 00:11:22:33:44:55 /lib/firmware/ath10k/cal-pci-0000:0c:00.0.bin
(and then either reload ath10k or reboot the system)
another options would be through uci/luci. The "macaddr" option in the interface section can be used to override it. https://openwrt.org/docs/guide-user/base-system/basic-networking#options_valid_for_all_protocol_types
2 Likes
thnx for quick answer
card are have no embdded eeprom so exctracted file it is.
for dynamic mac allocation can i use somthing like
ath10kcal_patch_mac (macaddr_add (cat /sys/class/net/eth0/address) +1) /lib/firmware ath10k/cal-pci-0000:0b:00.0.bin
ath10kcal_patch_mac (macaddr_add (cat /sys/class/net/eth0/address) +2) /lib/firmware/ath10k/cal-pci-0000:0c:00.0.bin
ath10kcal_patch_mac (macaddr_add (cat /sys/class/net/eth0/address) +3) /lib/firmware/ath10k/cal-pci-0000:0d:00.0.bin
br.
get it finallay.
it a matter of patching cal data with wanted mac addr.
and forget about last part from last msg.
1 Like
This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.