Hello
I saw that the MR600V2 can be flashed with openwrt.
however there is no factory.bin file
I compiled ap51 under debian 11 but nothing happens in the router.
No change.
I saw that the gargoyle firmware (based on openwrt) offers a factory.bin file.
Can we patch it and switch to an openwrt version?
Can someone guide me?
Sorry for my english (french)
David
See https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d9a3af46d8a1001223c2a327f449b7048d0fd5f6 for MR600 v2 installation instructions.
Where can I find more details on ap51?
destination ip address?
Which file to send?
Otherwise I'll switch to TFTP....
on the github page linked to ?
note TFTP requires serial.
no information on ap51 usage ....
???
What does this mean?
(Veuillez utiliser des phrases complètes.)
serial port only with TX/RX?
Please use full sentences.
Serial requires:
Tx <> Rx
Rx <> Tx
Ground/Earth <> Ground/Earth
(Merci de créer un nouveau message pour transmettre de nouvelles informations.)
trial and error ?
it can't be rocket science ...
and there's a man page - https://github.com/ap51-flash/ap51-flash/blob/main/man/ap51-flash.8
Don't work with ap51 ...
If i specified mac, same problem
I tried to reboot for enter en tftp mode, same problem.
I don't have now a serial port ...
that's the 2 option ? can't find it on the man page ...
you might want to try wireshark and log the traffic, see what IP the requests are coming from.
I have logged the trafficbut any information on port 69 UDP and TCP ...
I will find a serial port ...
I have found an serial port
The log and password found on the net is admin/1234 but i can't find root password ...
The command "setenv" don't work ...
tftpboot same problem
This router could be flashed really?
Cordially
You have logged in to the OS, not the bootloader.
The bootloader is only active for a short time after power on. When you first turn the router power on, you should see some messages on serial from the bootloader then it will pause on the line "hit any key to stop autoboot" or "Autobooting in X seconds." Hit any key at that point for the bootloader shell/CLI. If you don't stop the autoboot within a few seconds, it will go on and boot the OS, which is not what you want. You will need to cut the power and try again.
I thought ap51flash was only for RedBoot not Uboot. But that was a long time ago it may have changed.
Thanks for your response, but i have tested, same problem
i can't stop the bootloader
[ 3.824000] GMAC1_MAC_ADRL -- : 0x4a3a47c2
[ 3.832000] PROC INIT OK!
[ 3.948000] usbcore: registered new interface driver cdc_wdm
[ 4.000000] usbcore: registered new interface driver usbserial
[ 4.004000] usbserial: USB Serial support registered for generic
[ 4.012000] usbcore: registered new interface driver usbserial_generic
[ 4.068000] dns_init
[ 4.072000] domain_name:tplinkmodem.net
[ 4.156000] l2tp_core: L2TP core driver, V2.0
[ 4.164000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
Please press Enter to activate this console.
starting pid 115, tty '': '/sbin/getty -L ttyS1 115200 vt100'
MT7621 login:
MT7621 login:
MT7621 login:
MT7621 login:
MT7621 login: [err] syslogd[main --1001] syslogd : syslogd_init
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
[ 6.592000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x10000, ret 0, retlen 0x10000
[ 6.624000] spiflash_ioctl_read, Read from 0x00fd0000 length 0xbef0, ret 0, retlen 0xbef0
[ dm_loadCfg ] 2504: currSwRevision = 55aa0105 currSwRevision = 55aa0105
[ 6.672000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x10000, ret 0, retlen 0x10000
[ 6.700000] spiflash_ioctl_read, Read from 0x00fd0000 length 0xbef0, ret 0, retlen 0xbef0
MT7621 login: [ 7.228000] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[ 7.252000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x870ad180, ep_ctx 0xa0c0d080, sch_ep 0x873fb400
[ 7.268000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x870ad1ac, ep_ctx 0xa0c0d060, sch_ep 0x873fb180
Hello
I can't login, my log from the boot:
U-Boot 1.1.3 (Sep 14 2021 - 16:13:01)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fa0000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
flash manufacture id: c8, device id 40 18
find flash: GD25Q128C
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Sep 14 2021 Time:16:13:01
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
#Reset_MT7530
set LAN/WAN WLLLL
0
disable Switch Phy
3: System Boot system code via Flash.
## Booting image at bc020200 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1942725 Bytes = 1.9 MB
Load Address: 81001000
Entry Point: 813cecd0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 813cecd0) ...
## Giving linux memsize in MB, 128
Starting kernel ...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
[ 0.000000] Linux version 3.10.14 (tp-link@Sohoidev) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Tue Sep 14 16:18:22 CST 2021
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @816a0000 s7040 r8192 d13440 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00032410
[ 0.000000] Readback ErrCtl register=00032410
[ 0.000000] Memory: 124064k/131072k available (3934k kernel code, 7008k reserved, 1323k data, 240k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.096000] Calibrating delay loop... 574.46 BogoMIPS (lpj=1148928)
[ 0.124000] pid_max: default: 32768 minimum: 301
[ 0.128000] Mount-cache hash table entries: 512
[ 0.132000] launch: starting cpu1
[ 0.136000] launch: cpu1 gone!
[ 0.136000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.136000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.136000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.136000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.168000] Synchronize counters for CPU 1: done.
[ 0.172000] launch: starting cpu2
[ 0.176000] launch: cpu2 gone!
[ 0.176000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.176000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.176000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.176000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.208000] Synchronize counters for CPU 2: done.
[ 0.212000] launch: starting cpu3
[ 0.216000] launch: cpu3 gone!
[ 0.216000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.216000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.216000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.216000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.244000] Synchronize counters for CPU 3: done.
[ 0.248000] Brought up 4 CPUs
[ 0.252000] devtmpfs: initialized
[ 0.256000] NET: Registered protocol family 16
[ 0.484000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.492000] PCIE PHY initialize
[ 0.492000] ***** Xtal 40MHz *****
[ 0.496000] start MT7621 PCIe register access
[ 0.952000] RALINK_RSTCTRL = 7000000
[ 0.956000] RALINK_CLKCFG1 = 77ffeff8
[ 0.960000]
[ 0.960000] *************** MT7621 PCIe RC mode *************
[ 1.340000] PCIE2 no card, disable it(RST&CLK)
[ 1.344000] pcie_link status = 0x3
[ 1.348000] RALINK_RSTCTRL= 3000000
[ 1.352000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.360000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.364000] PCIE0 enabled
[ 1.368000] PCIE1 enabled
[ 1.368000] interrupt enable status: 300000
[ 1.372000] Port 1 N_FTS = 1b105000
[ 1.376000] Port 0 N_FTS = 1b105000
[ 1.380000] config reg done
[ 1.384000] init_rt2880pci done
[ 1.396000] bio: create slab <bio-0> at 0
[ 1.404000] usbcore: registered new interface driver usbfs
[ 1.408000] usbcore: registered new interface driver hub
[ 1.412000] usbcore: registered new device driver usb
[ 1.420000] PCI host bridge to bus 0000:00
[ 1.424000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.428000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.436000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.444000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.452000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.460000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.464000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 1.472000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.480000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.484000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.492000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.496000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.504000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 1.512000] pci 0000:02:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 1.520000] pci 0000:02:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 1.528000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.532000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 1.540000] BAR0 at slot 0 = 0
[ 1.544000] bus=0x0, slot = 0x0
[ 1.544000] res[0]->start = 0
[ 1.548000] res[0]->end = 0
[ 1.552000] res[1]->start = 60300000
[ 1.556000] res[1]->end = 6030ffff
[ 1.560000] res[2]->start = 0
[ 1.560000] res[2]->end = 0
[ 1.564000] res[3]->start = 0
[ 1.568000] res[3]->end = 0
[ 1.568000] res[4]->start = 0
[ 1.572000] res[4]->end = 0
[ 1.576000] res[5]->start = 0
[ 1.580000] res[5]->end = 0
[ 1.580000] BAR0 at slot 1 = 0
[ 1.584000] bus=0x0, slot = 0x1
[ 1.588000] res[0]->start = 0
[ 1.592000] res[0]->end = 0
[ 1.592000] res[1]->start = 60310000
[ 1.596000] res[1]->end = 6031ffff
[ 1.600000] res[2]->start = 0
[ 1.604000] res[2]->end = 0
[ 1.604000] res[3]->start = 0
[ 1.608000] res[3]->end = 0
[ 1.612000] res[4]->start = 0
[ 1.616000] res[4]->end = 0
[ 1.616000] res[5]->start = 0
[ 1.620000] res[5]->end = 0
[ 1.624000] bus=0x1, slot = 0x0, irq=0x4
[ 1.628000] res[0]->start = 60000000
[ 1.632000] res[0]->end = 600fffff
[ 1.632000] res[1]->start = 0
[ 1.636000] res[1]->end = 0
[ 1.640000] res[2]->start = 0
[ 1.644000] res[2]->end = 0
[ 1.644000] res[3]->start = 0
[ 1.648000] res[3]->end = 0
[ 1.652000] res[4]->start = 0
[ 1.656000] res[4]->end = 0
[ 1.656000] res[5]->start = 0
[ 1.660000] res[5]->end = 0
[ 1.664000] bus=0x2, slot = 0x1, irq=0x18
[ 1.668000] res[0]->start = 60100000
[ 1.672000] res[0]->end = 601fffff
[ 1.672000] res[1]->start = 0
[ 1.676000] res[1]->end = 0
[ 1.680000] res[2]->start = 60200000
[ 1.684000] res[2]->end = 60203fff
[ 1.688000] res[3]->start = 0
[ 1.688000] res[3]->end = 0
[ 1.692000] res[4]->start = 60204000
[ 1.696000] res[4]->end = 60204fff
[ 1.700000] 00000] flash manufacture id: c8, device id 40 18
[ 2.004000] GD25Q128C(c8 40180000) (16384 Kbytes)
[ 2.008000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[ 2.020000] Creating 6 MTD partitions on "raspi":
[ 2.024000] 0x000000000000-0x000000020000 : "boot"
[ 2.028000] 0x000000020000-0x000000220000 : "kernel"
[ 2.036000] 0x000000220000-0x000000fc0000 : "rootfs"
[ 2.040000] mtd: partition "rootfs" set to be root filesystem
[ 2.048000] 0x000000fc0000-0x000000fd0000 : "romfile"
[ 2.052000] 0x000000fd0000-0x000000fe0000 : "config"
[ 2.056000] 0x000000fe0000-0x000000ff0000 : "radio"
[ 2.064000] Register flash device:flash0
[ 2.068000] DEV flash0: major 200
[ 2.072000] PPP generic driver version 2.4.2
[ 2.076000] PPP MPPE Compression module registered
[ 2.080000] NET: Registered protocol family 24
[ 2.084000] PPTP driver version 0.8.5
[ 2.088000] rdm_major = 253
[ 2.092000] lte_sd_kicking_writeback: set sd_kicking = 0!
[ 2.096000] lte_power_writeback: POWER OFF lte modem!
[ 2.104000] lte_wlan_status_writeback: set lte_wlan_status = 0!
[ 2.108000] Ralink gpio driver initialized
[ 2.112000] Mirror/redirect action on
[ 2.1160
starting pid 52, tty '': '/etc/init.d/rcS'
mount: mounting devpts on /dev/pts failed: No such file or directory
[ 2.768000] SCSI subsystem initialized
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/core/usbcore.ko': No such file or directory
[ 2.848000] Started WatchDog Timer.
[ 2.848000] Ralink APSoC Hardware Watchdog Timer
mount: mounting usbfs on /proc/bus/usb/ failed: No such device
[ 2.932000] *****run project phy.
[ 2.940000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 2.952000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 2.964000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 2.976000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 2.988000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.000000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.012000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.024000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.036000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.048000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.076000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.088000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.100000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.112000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.124000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.136000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.148000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.160000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.172000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.184000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.308000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 3.312000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 3.320000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 3.328000] hub 1-0:1.0: USB hub found
[ 3.332000] hub 1-0:1.0: 2 ports detected
[ 3.336000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 3.340000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 3.348000] hub 2-0:1.0: USB hub found
[ 3.352000] hub 2-0:1.0: 1 port detected
[ 3.360000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.372000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.384000] usbcore: registered new interface driver usb-storage
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/scsi/scsi_wait_scan.ko': No such file or directory
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/host/ifxusb_host.ko': No such file or directory
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/rt_rdm/rt_rdm.ko': No such file or directory
[ 3.436000] spiflash_ioctl_read, Read from 0x00fcf100 length 0x6, ret 0, retlen 0x6
[ 3.444000] Read MAC from flash(0xFCF100) ffffff90-ffffff9a-4a-3a-47-ffffffc2
[ 3.452000] GMAC1_MAC_ADRH -- : 0x0000909a
[ 3.456000] GMAC1_MAC_ADRL -- : 0x4a3a47c2
[ 3.460000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
[ 3.472000] spiflash_ioctl_read, Read from 0x00fcf100 length 0x6, ret 0, retlen 0x6
[ 3.480000] Read MAC from flash(0xFCF100) ffffff90-ffffff9a-4a-3a-47-ffffffc2
[ 3.484000] GMAC1_MAC_ADRH -- : 0x0000909a
[ 3.488000] GMAC1_MAC_ADRL -- : 0x4a3a47c2
[ 3.496000] PROC INIT OK!
[ 3.608000] usbcore: registered new interface driver cdc_wdm
[ 3.660000] usbcore: registered new interface driver usbserial
[ 3.668000] usbserial: USB Serial support registered for generic
[ 3.672000] usbcore: registered new interface driver usbserial_generic
[ 3.732000] dns_init
[ 3.736000] domain_name:tplinkmodem.net
[ 3.760000] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[ 3.792000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x871c0d00, ep_ctx 0xa0c0d080, sch_ep 0x871c3f80
[ 3.808000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x871c0d2c, ep_ctx 0xa0c0d060, sch_ep 0x871c3d00
[ 3.820000] l2tp_core: L2TP core driver, V2.0
[ 3.824000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x871c0c80, ep_ctx 0xa0c0d0a0, sch_ep 0x871c3a80
[ 3.840000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x871c0cac, ep_ctx 0xa0c0d0c0, sch_ep 0x871c3880
[ 3.856000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 3, maxp 10, interval 256, burst 0, mult 0, ep 0x87e93880, ep_ctx 0xa0c0d140, sch_ep 0x871c3600
[ 3.856000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.872000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x87e938ac, ep_ctx 0xa0c0d100, sch_ep 0x871c3380
[ 3.888000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x87e938d8, ep_ctx 0xa0c0d0e0, sch_ep 0x871c3180
[ 3.904000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 3, maxp 10, interval 256, burst 0, mult 0, ep 0x87e93780, ep_ctx 0xa0c0d1c0, sch_ep 0x871c4e00
[ 3.916000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x87e937ac, ep_ctx 0xa0c0d180, sch_ep 0x871c4b80
[ 3.932000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x87e937d8, ep_ctx 0xa0c0d120, sch_ep 0x871c4980
[ 3.948000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 3, maxp 8, interval 256, burst 0, mult 0, ep 0x87e93680, ep_ctx 0xa0c0d240, sch_ep 0x871c4700
[ 3.960000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x87e936ac, ep_ctx 0xa0c0d200, sch_ep 0x871c4480
[ 3.976000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x87e936d8, ep_ctx 0xa0c0d160, sch_ep 0x871c4280
[ 3.992000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x871c0c00, ep_ctx 0xa0c0d280, sch_ep 0x871e4f00
[ 4.004000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x871c0c2c, ep_ctx 0xa0c0d1a0, sch_ep 0x871e4c80
Please press Enter to activate this console.
starting pid 115, tty '': '/sbin/getty -L ttyS1 115200 vt100'
[ 4.044000] usbserial_generic 1-2:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.
[ 4.056000] usbserial_generic 1-2:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.
[ 4.064000] usbserial_generic 1-2:1.0: generic converter detected
[ 4.072000] usb 1-2: generic converter now attached to ttyUSB0
[ 4.076000] usb-storage 1-2:1.5: USB Mass Storage device detected
[ 4.084000] scsi0 : usb-storage 1-2:1.5
MT7621 login: [err] syslogd[main --1001] syslogd : syslogd_init
[ 5.096000] scsi 0:0:0:0: Direct-Access Linux File-Stor Gadget 0318 PQ: 0 ANSI: 2
[ 5.108000] sd 0:0:0:0: [sda] 143360 512-byte logical blocks: (73.4 MB/70.0 MiB)
[ 5.116000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.120000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.132000] sda:
[ 5.136000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
[ 6.424000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x10000, ret 0, retlen 0x10000
any key work ..
the uboot can't stop