How to define USB port on dts file of EX6200v2

EX6200v2 use CPU is same as EX6150v2/EX6100v2. so I want build firmware for EX6200v2 base on E6150v2 18.06.2.
Now the firmware can work normally on NAT and wifi, but USB port cannot working. plug in any usb devices, system not not any response.

I guess is dts issue, but I don't known how to fixed it. hope get help on here.

Following is my DTS file:

/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
 *
 * Permission to use, copy, modify, and/or distribute this software for any
 * purpose with or without fee is hereby granted, provided that the above
 * copyright notice and this permission notice appear in all copies.
 *
 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
 *
 */

#include "qcom-ipq4019.dtsi"
#include "qcom-ipq4019-bus.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>

/ {
	model = "Netgear EX6200v2";
	compatible = "netgear,ex6200v2", "qcom,ipq4019";

	aliases {
		led-boot = &power_amber;
		led-failsafe = &power_amber;
		led-running = &power_green;
		led-upgrade = &power_amber;
	};

	soc {
		mdio@90000 {
			status = "okay";
		};

		ess-psgmii@98000 {
			status = "okay";
		};

		tcsr@1949000 {
			compatible = "qcom,tcsr";
			reg = <0x1949000 0x100>;
			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
		};

		tcsr@194b000 {
			compatible = "qcom,tcsr";
			reg = <0x194b000 0x100>;
			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
		};

		ess_tcsr@1953000 {
			compatible = "qcom,tcsr";
			reg = <0x1953000 0x1000>;
			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
		};

		tcsr@1957000 {
			compatible = "qcom,tcsr";
			reg = <0x1957000 0x100>;
			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
		};


		serial@78af000 {
			pinctrl-0 = <&serial_pins>;
			pinctrl-names = "default";
			status = "okay";
		};

		usb2@60f8800 {
			status = "okay";
		};

		usb3@8af8800 {
			status = "okay";
		};

		crypto@8e3a000 {
			status = "okay";
		};

		wifi@a000000 {
			status = "okay";
			qcom,ath10k-calibration-variant = "Netgear-EX6200v2";
		};

		wifi@a800000 {
			status = "okay";
			qcom,ath10k-calibration-variant = "Netgear-EX6200v2";
		};

		watchdog@b017000 {
			status = "okay";
		};

		ess-switch@c000000 {
			status = "okay";
		};

		edma@c080000 {
			status = "okay";
		};
	};

	gpio-keys {
		compatible = "gpio-keys";

		reset {
			label = "reset";
			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_RESTART>;
		};

		wps {
			label = "wps";
			gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_WPS_BUTTON>;
		};
	};

    led_spi {
                compatible = "spi-gpio";
                #address-cells = <1>;
                ranges;

                gpio-sck = <&tlmm 5 GPIO_ACTIVE_HIGH>;
                gpio-mosi = <&tlmm 4 GPIO_ACTIVE_HIGH>;
                num-chipselects = <0>;

                led_gpio: led_gpio@0 {
                        compatible = "fairchild,74hc595";
                        reg = <0>;
                        gpio-controller;
                        #gpio-cells = <2>;
                        registers-number = <1>;
                        spi-max-frequency = <1000000>;
                };
        };

	gpio-leds {
		compatible = "gpio-leds";

		power_amber: power_amber {
                        label = "ex6200v2:amber:power";
                        gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
                };

                power_green: power_green {
                        label = "ex6200v2:green:power";
                        gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
                };

                right {
                        label = "ex6200v2:blue:right";
                        gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
                };

                left {
                        label = "ex6200v2:blue:left";
                        gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
                };

                client_green {
                        label = "ex6200v2:green:client";
                        gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
                };

                client_red {
                        label = "ex6200v2:red:client";
                        gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
                };

                router_green {
                        label = "ex6200v2:green:router";
                        gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
                };

                router_red {
                        label = "ex6200v2:red:router";
                        gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
                };

                wps {
                        label = "ex6200v2:green:wps";
                        gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
                };
	};
};

&cryptobam {
	status = "okay";
};

&blsp_dma {
	status = "okay";
};

&tlmm {
	serial_pins: serial_pinmux {
		mux {
			pins = "gpio60", "gpio61";
			function = "blsp_uart0";
			bias-disable;
		};
	};

	spi_0_pins: spi_0_pinmux {
		pin {
			function = "blsp_spi0";
			pins = "gpio55", "gpio56", "gpio57";
			drive-strength = <12>;
			bias-disable;
		};

		pin_cs {
			function = "gpio";
			pins = "gpio54", "gpio59";
			drive-strength = <2>;
			bias-disable;
			output-high;
		};
	};
};

&spi_0 { /* BLSP1 QUP1 */
	pinctrl-0 = <&spi_0_pins>;
	pinctrl-names = "default";
	status = "okay";
	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;

	 mx25l12805d@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <24000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition0@0 {
                                label = "SBL1";
                                reg = <0x00000000 0x00040000>;
                                read-only;
                        };

                        partition1@40000 {
                                label = "MIBIB";
                                reg = <0x00040000 0x00020000>;
                                read-only;
                        };

                        partition2@60000 {
                                label = "QSEE";
                                reg = <0x00060000 0x00060000>;
                                read-only;
                        };

                        partition3@c0000 {
                                label = "CDT";
                                reg = <0x000c0000 0x00010000>;
                                read-only;
                        };

                        partition4@d0000 {
                                label = "DDRPARAMS";
                                reg = <0x000d0000 0x00010000>;
                                read-only;
                        };

                        partition5@E0000 {
                                label = "APPSBLENV";
                                reg = <0x000e0000 0x00010000>;
                                read-only;
                        };

                        partition6@F0000 {
                                label = "APPSBL";
                                reg = <0x000f0000 0x00080000>;
                                read-only;
                        };

                        partition7@170000 {
                                label = "ART";
                                reg = <0x00170000 0x00010000>;
                                read-only;
                        };

                        partition8@180000 {
                                label = "config";
                                reg = <0x00180000 0x00010000>;
                                read-only;
                        };

                        partition9@190000 {
                                label = "pot";
                                reg = <0x00190000 0x00010000>;
                                read-only;
                        };

                        partition10@1a0000 {
                                label = "dnidata";
                                reg = <0x001a0000 0x00010000>;
                                read-only;
                        };

                        partition11@1b0000 {
                                label = "firmware";
                                reg = <0x001b0000 0x00e10000>;
                        };

                        partition12@fc0000 {
                                label = "language";
                                reg = <0x00fc0000 0x00040000>;
                                read-only;
                        };
		
		};
	};
};

&usb3_ss_phy {
	status = "okay";
};

&usb3_hs_phy {
	status = "okay";
};

&usb2_hs_phy {
	status = "okay";
};

Try with these changes for USB2?

	enable-usb-power {
		gpio-hog;
		gpios = <58 GPIO_ACTIVE_HIGH>;
		output-low;
		line-name = "enable USB2 power";
};

Thanks!
I try to add these code to dts. but usb cannot use also.

I have a question, if need add these code, but how to confirm what GPIO port be used by USB?

Not sure either since the other EX61XX devices don't have a USB port.

Yes!
Now, other function is OK. Only USB function is not working!
EX61**v2 serial only have one ethernet.

Looking at the 8devices-Jalapeno dts which has USB ports I cant see any additions ?

https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob_plain;f=target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts;h=7e2bdcc7cda60eaa5480c2c59c6e9e150e4ecc91;hb=1e341bb5ef9ba342a56ad2765c2876091fdc66db

hi tony
did you make usb work on ex6150v2?
thanks