Help please! Boot loop in a 4G LTE Router H3S R01 4G

Installing and Using OpenWrt
1

I'm Gabriel from Colombia.
I bought a router H3S R01 4G LTE (H3S.com.co), then I noticed that it runs OpenWRT. I got ssh acces and I tried to upgrade but I choosed the wrong bin, there is a MT7628NN inside and I used a MT7628AN image.
There isnt much information about the device. Its made by Shangai Notion Information Technology https://www.notioni.com/ .I've tried to contact H3S and Notion to info or tools but they dont response. Same that H3S there's a mark that use that oem device, Ergo r0516.
I have serial access and I got this:

[05010C07][05010C0A]
DDR Calibration DQS reg = 00008988


U-Boot 1.1.3 (Jul 14 2020 - 16:23:39)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
flash manufacture id: 20, device id 70 18
find flash: XM25QH128A
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jul 14 2020  Time:16:23:39
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 575 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!xiehj: forcegrade = restore
xiehj:key pressed

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: spi flash mcp test.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc800000 ...
   Image Name:   MIPS OpenWrt Linux-5.4.108
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1984719 Bytes =  1.9 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 5.4.108 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15952-6090337679)) #0 Sat Apr 3 15:06:39 2021
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is Mediatek MT7628AN evaluation board
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=000690d6
[    0.000000] Readback ErrCtl register=000690d6
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 57512K/65536K available (5052K kernel code, 203K rwdata, 632K rodata, 1208K init, 205K bss, 8024K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] intc: using register map from devicetree
[    0.000000] random: get_random_bytes called from 0x805c2984 with crng_init=0
[    0.000000] CPU Clock: 575MHz
[    0.000000] timer_probe: no matching timers found
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6647862422 ns
[    0.000010] sched_clock: 32 bits at 287MHz, resolution 3ns, wraps every 7469508094ns
[    0.015390] Calibrating delay loop... 382.46 BogoMIPS (lpj=764928)
[    0.055425] pid_max: default: 32768 minimum: 301
[    0.064762] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.079095] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.100574] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.119780] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.133289] pinctrl core: initialized pinctrl subsystem
[    0.146465] NET: Registered protocol family 16
[    0.181722] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.204693] clocksource: Switched to clocksource MIPS
[    0.215981] NET: Registered protocol family 2
[    0.225670] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.242154] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.257224] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.271148] TCP: Hash tables configured (established 1024 bind 1024)
[    0.283863] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.296720] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.310781] NET: Registered protocol family 1
[    0.319320] PCI: CLS 0 bytes, default 32
[    0.331678] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.353037] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.364470] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.399216] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.417086] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.428340] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.439583] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.450822] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.466384] printk: console [ttyS0] disabled
[    0.474820] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[    0.492618] printk: console [ttyS0] enabled
[    0.492618] printk: console [ttyS0] enabled
[    0.509106] printk: bootconsole [early0] disabled
[    0.509106] printk: bootconsole [early0] disabled
[    0.529232] spi-mt7621 10000b00.spi: sys_freq: 191666666
[    0.549324] spi-nor spi0.0: XM25QH128A (16384 Kbytes)
[    0.559435] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.572018] Creating 4 MTD partitions on "spi0.0":
[    0.581516] 0x000000000000-0x000000030000 : "u-boot"
[    0.592531] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.604283] 0x000000040000-0x000000050000 : "factory"
[    0.615502] 0x000000050000-0x000000800000 : "firmware"
[    0.630724] 2 uimage-fw partitions found on MTD device firmware
[    0.642515] Creating 2 MTD partitions on "firmware":
[    0.652362] 0x000000000000-0x00000014aef0 : "kernel"
[    0.663373] 0x00000014aef0-0x0000007b0000 : "rootfs"
[    0.674370] mtd: device 5 (rootfs) set to be root filesystem
[    0.687653] 1 squashfs-split partitions found on MTD device rootfs
[    0.699985] 0x000000650000-0x0000007b0000 : "rootfs_data"
[    0.712758] libphy: Fixed MDIO Bus: probed
[    0.732377] rt3050-esw 10110000.esw: link changed 0x00
[    0.743791] mtk_soc_eth 10100000.ethernet: generated random MAC address 62:f7:a8:cf:58:3b
[    0.760860] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.779382] NET: Registered protocol family 10
[    0.792773] Segment Routing with IPv6
[    0.800187] NET: Registered protocol family 17
[    0.809070] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.834737] 8021q: 802.1Q VLAN Support v1.8
[    0.846750] squashfs image failed sanity check
[    0.856023] VFS: Cannot open root device "(null)" or unknown-block(31,5): error -5
[    0.871074] Please append a correct "root=" boot option; here are the available partitions:
[    0.887625] 1f00             192 mtdblock0
[    0.887628]  (driver?)
[    0.900575] 1f01              64 mtdblock1
[    0.900577]  (driver?)
[    0.913526] 1f02              64 mtdblock2
[    0.913529]  (driver?)
[    0.926474] 1f03            7872 mtdblock3
[    0.926477]  (driver?)
[    0.939422] 1f04            1323 mtdblock4
[    0.939425]  (driver?)
[    0.952370] 1f05            6548 mtdblock5
[    0.952373]  (driver?)
[    0.965319] 1f06            1408 mtdblock6
[    0.965321]  (driver?)
[    0.978267] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
[    0.994797] Rebooting in 1 seconds..
[05010C07][05010C0A]

I thanks a lot if you can help me.

1 Like
2

TFTP boot looks like a good choice, you should start with 1, and use the initramfs image.
If there are no firmware images available from the manufacturer, you'll need to swap to openwrt, or look for a flash dump.

1 Like
3

Thank you so much! A question, where do I find more info about the initramfs image? And if I dont have firmware images available from the manufacturer how to swap to openwrt? Thank you again

4

It's basically an image with the file system attached to it, designed to run in memory only,
nothing is written to the flash.

Like I said, u-boot boot option 1, to start with, see if you can get it to run that way.
you will probably need to provide a TFTP server with the image renamed, but you'll see what it needs to be, when it will try to DL it (or run printenv/envprint in u-boot).
Same goes with IP, probably need to be static.

https://downloads.openwrt.org/releases/19.07.7/targets/ramips/mt76x8/ (<- URL updated)

1 Like
5

I got this, that means that I have to create a TFTP Server and put the file 'firmware.bin' in, Right? also I've watched that is required set the ip to a specific ip.

[05010C07][05010C0A]
DDR Calibration DQS reg = 00008988


U-Boot 1.1.3 (Jul 14 2020 - 16:23:39)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
flash manufacture id: 20, device id 70 18
find flash: XM25QH128A
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jul 14 2020  Time:16:23:39
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 575 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!xiehj: forcegrade = restore
xiehj:key pressed

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: spi flash mcp test.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 1
                                                                              0
xiehj:key pressed


2: System Load Linux Kernel then write to Flash via TFTP.
 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
 Please Input new ones /or Ctrl-C to discard
        Input device IP (10.10.10.123)  Input server IP (10.10.10.3)    Input Li                                                                                                 nux Kernel filename ()
 netboot_common, argc= 3

 NetTxPacket = 0x83FE5BC0

 KSEG1ADDR(NetTxPacket) = 0xA3FE5BC0

 NetLoop,call eth_halt !

 NetLoop,call eth_init !
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done


 ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'firmware.bin'.

 TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
6

correct, need to change the IP on your TFTP host, and rename the openwrt file.

Don't forget to disable the firewall on your TFTP host.

the TFTP parameters (and a lot of other things too) can be changed, once you jump to 4.

8

Try English....

9

Hey Gabo did you install dd-wrt Firmware on the H3S Router?

Please let me know,
thanks

1 Like
10

No yet.
Im trying right now

11 
[05000C07][05000C0B]
DDR Calibration DQS reg = 00008987


U-Boot 1.1.3 (Jul 14 2020 - 16:23:39)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
flash manufacture id: 20, device id 70 18
find flash: XM25QH128A
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jul 14 2020  Time:16:23:39
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 575 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!xiehj: forcegrade = restore

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: spi flash mcp test.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                                                                                                                      0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   OpenWrt Linux-3.10.14-p112871
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1355440 Bytes =  1.3 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
[    0.000000] Linux version 3.10.14 (jenkins@wh-cis01) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Tue Jul 14 16:29:16 CST 2020
[    0.000000]
[    0.000000]  The CPU feqenuce set to 575 MHz
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=000792d2
[    0.000000] Readback ErrCtl register=000792d2
[    0.000000] Memory: 60756k/65536k available (3023k kernel code, 4756k reserved, 711k data, 232k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.096000] Calibrating delay loop... 382.46 BogoMIPS (lpj=764928)
[    0.128000] pid_max: default: 32768 minimum: 301
[    0.132000] Mount-cache hash table entries: 512
[    0.136000] NET: Registered protocol family 16
[    0.140000] RALINK_GPIOMODE = 54054404
[    0.144000] RALINK_GPIOMODE = 54044404
[    0.244000] ***** Xtal 25MHz *****
[    0.248000] start PCIe register access
[    0.748000] RALINK_RSTCTRL = 2400000
[    0.752000] RALINK_CLKCFG1 = fdbfffc0
[    0.756000]
[    0.756000] *************** MT7628 PCIe RC mode *************
[    1.256000] PCIE0 no card, disable it(RST&CLK)
[    1.288000] bio: create slab <bio-0> at 0
[    1.292000] usbcore: registered new interface driver usbfs
[    1.296000] usbcore: registered new interface driver hub
[    1.300000] usbcore: registered new device driver usb
[    1.304000] cfg80211: Calling CRDA to update world regulatory domain
[    1.308000] Switching to clocksource MIPS
[    1.312000] NET: Registered protocol family 2
[    1.324000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.336000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.348000] TCP: Hash tables configured (established 512 bind 512)
[    1.360000] TCP: reno registered
[    1.368000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.392000] NET: Registered protocol family 1
[    1.400000] MTK/Ralink EHCI/OHCI init.
[    1.408000] MTK/Ralink leds init.
[    1.416000] MTK/Ralink keys init.
[    1.424000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.436000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.456000] msgmni has been set to 118
[    1.464000] io scheduler noop registered (default)
[    1.484000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.496000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[    1.508000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    1.524000] Ralink gpio driver initialized
[    1.532000] flash manufacture id: 20, device id 70 18
[    1.544000] XM25QH128A(20 70180000) (16384 Kbytes)
[    1.552000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[    1.572000] Creating 7 MTD partitions on "raspi":
[    1.580000] 0x000000000000-0x000001000000 : "ALL"
[    1.592000] 0x000000000000-0x000000030000 : "Bootloader"
[    1.604000] 0x000000030000-0x000000040000 : "Config"
[    1.616000] 0x000000040000-0x000000050000 : "Factory"
[    1.628000] 0x000000050000-0x000000800000 : "firmware1"
[    1.640000] 0x00000019aef0-0x000000800000 : "rootfs"
[    1.648000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.676000] mtd: partition "rootfs_data" created automatically, ofs=0x6a0000, len=0x160000
[    1.692000] 0x0000006a0000-0x000000800000 : "rootfs_data"
[    1.704000] 0x000000800000-0x000000fb0000 : "firmware2"
[    1.716000] 0x000000fb0000-0x000001000000 : "reserved"
[    1.728000] PPP generic driver version 2.4.2
[    1.736000] PPP MPPE Compression module registered
[    1.748000] NET: Registered protocol family 24
[    1.756000] PPTP driver version 0.8.5
[    1.764000] GMAC1_MAC_ADRH -- : 0x00008c88
[    1.772000] GMAC1_MAC_ADRL -- : 0x2b000019
[    1.780000] Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500!
[    1.800000] GMAC1_MAC_ADRH -- : 0x00008c88
[    1.808000] GMAC1_MAC_ADRL -- : 0x2b000019
[    1.816000] PROC INIT OK!
[    1.820000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.836000] ehci-pci: EHCI PCI platform driver
[    1.844000] ehci-platform: EHCI generic platform driver
[    1.872000] ******MT7628 mtk phy
[    1.880000] *****run project phy.
[    1.896000] FM_OUT value: u4FmOut = 0(0x00000000)
[    1.912000] FM_OUT value: u4FmOut = 147(0x00000093)
[    1.920000] FM detection done! loop = 1
[    1.936000] SR calibration value u1SrCalVal = 6
[    1.944000] *********Execute mt7628_phy_init!!
[    1.952000] ehci-platform ehci-platform: EHCI Host Controller
[    1.964000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    1.980000] ehci-platform ehci-platform: irq 18, io mem 0x101c0000
[    2.004000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    2.016000] hub 1-0:1.0: USB hub found
[    2.024000] hub 1-0:1.0: 1 port detected
[    2.032000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.064000] *********Execute mt7628_phy_init!!
[    2.072000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[    2.084000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    2.100000] ohci-platform ohci-platform: irq 18, io mem 0x101c1000
[    2.176000] hub 2-0:1.0: USB hub found
[    2.184000] hub 2-0:1.0: 1 port detected
[    2.192000] logger: created 256K log 'log_main'
[    2.200000] logger: created 256K log 'log_events'
[    2.212000] logger: created 256K log 'log_radio'
[    2.220000] logger: created 256K log 'log_system'
[    2.232000] ipip: IPv4 over IPv4 tunneling driver
[    2.240000] gre: GRE over IPv4 demultiplexor driver
[    2.252000] ip_gre: GRE over IPv4 tunneling driver
[    2.264000] TCP: cubic registered
[    2.268000] NET: Registered protocol family 10
[    2.280000] NET: Registered protocol family 17
[    2.288000] 8021q: 802.1Q VLAN Support v1.8
[    2.328000] registered taskstats version 1
[    2.344000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.360000] Freeing unused kernel memory: 232K (803a6000 - 803e0000)
[    3.156000] init: Console is alive
[    4.488000] xiehj : RALINK_REG_GPIOMODE = 0x55044410
[    4.496000] xiehj : RALINK_REG_GPIOMODE = 0x55044410
[    4.508000] wps_gpio = -1
[    4.512000] read_power = 5
[    4.520000] reset_cp_gpio = 46
[    4.528000] update_cp_gpio = 11
[    4.532000] register reboot notifier
[    4.548000] SCSI subsystem initialized
[    4.568000] usbcore: registered new interface driver usb-storage
[    4.592000] init: - preinit -
[    5.288000] Raeth v3.1 (Tasklet,SkbRecycle)
[    5.300000]
[    5.300000] phy_tx_ring = 0x03545000, tx_ring = 0xa3545000
[    5.312000]
[    5.312000] phy_rx_ring0 = 0x03546000, rx_ring0 = 0xa3546000
[    5.340000] GMAC1_MAC_ADRH -- : 0x00008c88
[    5.352000] GMAC1_MAC_ADRL -- : 0x2b000019
[    5.360000] RT305x_ESW: Link Status Changed

I get it from a H3S Router with original firmware.
Whats the next step? @frollic
I'll thank you.

12

well, nothing's changed.

you need to figure out why you can't transfer via TFTP to the device.

13

I got it, thank you so much!

14

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.