Hi everyone,
I am really new to here.
I can manage to boot into UART and showing cfg 04 by shoting boot_sel2 with GND.
However, tried to transfer "lede-lantiq-bthomehubv5a_ram-u-boot.asc" into the UART nothing happened (not showing anything) or just like this:
any ideas please?
In the past, I have successfully installed lede by tapping the wires to tx/rx points. But after updating the system, it won't boot into lede anymore with the log:
ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
DDR autotuning Rev 0.3d
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...
U-Boot 2010.06-LANTIQ-v-2.2.46 (Dec 06 2013 - 02:39:45 on tester@clean-machine)
CLOCK CPU 500M RAM 250M
secure boot
DRAM: 125 MiB
NAND: ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In: serial
Out: serial
Err: serial
Net: Internal phy(GE) firmware version: 0x841b
vr9 Switch
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000100000-0x000007f80000 : "mtd=0"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 126 MiB
UBI: number of good PEBs: 1012
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 4
UBI: available PEBs: 10
UBI: total number of reserved PEBs: 1002
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 382/258
Volume kernel found at volume id 0
read 0 bytes from volume 0 to 80800000(buf address)
Read [2064384] bytes
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.48
Created: 2018-06-07 19:44:04 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1996314 Bytes = 1.9 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.14.48 (buildbot@buildslave) (gcc version 7.3.0 (O penWrt GCC 7.3.0 r7137-e4259bed3f)) #0 SMP Thu Jun 7 19:44:04 2018
[ 0.000000] SoC: xRX200 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is BT Home Hub 5A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Detected 1 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x4a8 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu @8110e000 s25968 r8192 d23184 u5734 4
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=0007f802
[ 0.000000] Readback ErrCtl register=0007f802
[ 0.000000] Memory: 121872K/131072K available (4796K kernel code, 199K rwdata , 1340K rodata, 1264K init, 246K bss, 9200K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] Setting up vectored interrupts
[ 0.000000] Setting up IPI vectored interrupts
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 7645041786 ns
[ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 85899 34590ns
[ 0.007905] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.045962] pid_max: default: 32768 minimum: 301
[ 0.050879] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.057384] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.066581] Hierarchical SRCU implementation.
[ 0.071905] smp: Bringing up secondary CPUs ...
[ 0.077178] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.077191] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.077348] CPU1 revision is: 00019556 (MIPS 34Kc)
[ 0.108541] Synchronize counters for CPU 1: done.
[ 0.132840] smp: Brought up 1 node, 2 CPUs
[ 0.141519] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
[ 0.151175] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.157448] pinctrl core: initialized pinctrl subsystem
[ 0.164311] NET: Registered protocol family 16
[ 0.179226] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.185444] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.197236] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.210200] PCI host bridge /fpi@10000000/pci@e105400 ranges:
[ 0.215884] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.221144] IO 0x000000001ae00000..0x000000001affffff
[ 0.345263] PCI host bridge /fpi@10000000/pcie@d900000 ranges:
[ 0.374791] usbcore: registered new interface driver usbfs
[ 0.380340] usbcore: registered new interface driver hub
[ 0.385729] usbcore: registered new device driver usb
[ 0.391412] PCI host bridge to bus 0000:00
[ 0.395437] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.402342] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.409310] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.416141] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff]
[ 0.424804] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.431718] PCI host bridge to bus 0000:01
[ 0.435744] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.442659] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.449590] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.456443] pci_bus 0000:01: No busn resource found for root bus, will use [b us 01-ff]
[ 0.464525] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.482748] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), rec onfiguring
[ 0.491881] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c1fffff]
[ 0.498591] pci 0000:01:00.0: BAR 9: assigned [mem 0x1c200000-0x1c2fffff pref ]
[ 0.505863] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c1fffff 64bi t]
[ 0.513280] pci 0000:02:00.0: BAR 6: assigned [mem 0x1c200000-0x1c20ffff pref ]
[ 0.520516] pci 0000:01:00.0: PCI bridge to [bus 02]
[ 0.525577] pci 0000:01:00.0: bridge window [mem 0x1c000000-0x1c1fffff]
[ 0.532409] pci 0000:01:00.0: bridge window [mem 0x1c200000-0x1c2fffff pref ]
[ 0.541795] clocksource: Switched to clocksource MIPS
[ 0.549086] NET: Registered protocol family 2
[ 0.554859] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.561744] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.568154] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.574737] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.580523] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.587139] NET: Registered protocol family 1
[ 0.592354] gptu: totally 6 16-bit timers/counters
[ 0.597247] gptu: misc_register on minor 63
[ 0.601385] gptu: succeeded to request irq 126
[ 0.601796] random: fast init done
[ 0.609318] gptu: succeeded to request irq 127
[ 0.613895] gptu: succeeded to request irq 128
[ 0.618372] gptu: succeeded to request irq 129
[ 0.622900] gptu: succeeded to request irq 130
[ 0.627405] gptu: succeeded to request irq 131
[ 0.632092] No VPEs reserved for AP/SP, not initialize VPE loader
[ 0.632092] Pass maxvpes=<n> argument as kernel argument
[ 0.643459] No TCs reserved for AP/SP, not initializing RTLX.
[ 0.643459] Pass maxtcs=<n> argument as kernel argument
[ 0.656159] Crashlog allocated RAM at address 0x3f00000
[ 0.661980] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.678963] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.684747] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.700788] io scheduler noop registered
[ 0.704609] io scheduler deadline registered (default)
[ 0.713996] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.722978] console [ttyLTQ0] enabled
[ 0.722978] console [ttyLTQ0] enabled
[ 0.730245] bootconsole [early0] disabled
[ 0.730245] bootconsole [early0] disabled
[ 0.739239] cacheinfo: Failed to find cpu0 device node
[ 0.743015] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.751048] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.755962] nand: AMD/Spansion S34ML01G1
[ 0.759876] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64
[ 0.768014] Bad block table found at page 65472, version 0x01
[ 0.774023] Bad block table found at page 65408, version 0x01
[ 0.779229] 4 fixed-partitions partitions found on MTD device 14000000.nand
[ 0.785940] Creating 4 MTD partitions on "14000000.nand":
[ 0.791376] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.798026] 0x0000000a0000-0x0000000c0000 : "uboot-env"
[ 0.803410] 0x0000000c0000-0x000000100000 : "unused"
[ 0.808666] 0x000000100000-0x000007f80000 : "ubi"
[ 0.819011] libphy: Fixed MDIO Bus: probed
[ 0.826144] wdt 1f8803f0.watchdog: Init done
[ 0.835472] NET: Registered protocol family 10
[ 0.840381] Segment Routing with IPv6
[ 0.842818] NET: Registered protocol family 17
[ 0.847184] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.860058] 8021q: 802.1Q VLAN Support v1.8
[ 0.973189] libphy: lantiq,xrx200-mdio: probed
[ 0.982496] net-xrx200: invalid MAC, using random
[ 1.058444] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr =0:00, irq=POLL)
[ 1.142417] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr =0:01, irq=POLL)
[ 1.226398] Intel XWAY PHY11G (xRX v1.2 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:11, irq=POLL)
[ 1.310398] Intel XWAY PHY11G (xRX v1.2 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:13, irq=POLL)
[ 1.394421] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr =0:05, irq=POLL)
[ 1.411074] UBI: auto-attach mtd3
[ 1.412957] ubi0: attaching mtd3
[ 1.559788] ubi0: scanning is finished
[ 1.576035] ubi0: attached mtd3 (name "ubi", size 126 MiB)
[ 1.580155] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.587003] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.593708] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.600473] ubi0: good PEBs: 1012, bad PEBs: 0, corrupted PEBs: 0
[ 1.606579] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 12 8
[ 1.613815] ubi0: max/mean erase counter: 382/258, WL threshold: 4096, image sequence number: 1019015774
[ 1.623290] ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 20
[ 1.632690] ubi0: background thread "ubi_bgt0d" started, PID 423
[ 1.635330] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.635344] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.635810] USB_VBU[ 1.661938] VFS: Mounted root (squashfs filesystem) rea donly on device 254:0.
[ 1.671603] Freeing unused kernel memory: 1264K
[ 1.674729] This architecture does not have kernel memory protection.
[ 2.247372] init: Console is alive
[ 2.249670] init: - watchdog -
[ 3.451129] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.569263] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using du mmy regulator
[ 3.576296] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using du mmy regulator
[ 3.584802] dwc2 1e101000.usb: dwc2_core_reset() HANG! AHB Idle GRSTCTL=0
[ 3.793938] dwc2 1e101000.usb: DWC OTG Controller
[ 3.797239] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
[ 3.804347] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
[ 3.811167] hub 1-0:1.0: USB hub found
[ 3.813603] hub 1-0:1.0: 1 port detected
[ 3.819627] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.829621] init: - preinit -
[ 4.831396] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.836397] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link
[ 4.842126] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4.869656] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.088438] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 488
[ 8.118339] UBIFS (ubi0:2): recovery needed
[ 8.229710] UBIFS (ubi0:2): recovery completed
[ 8.232925] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "root fs_data"
[ 8.240605] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes
[ 8.250535] UBIFS (ubi0:2): FS size: 120508416 bytes (114 MiB, 934 LEBs), jou rnal size 6064128 bytes (5 MiB, 47 LEBs)
[ 8.261133] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 8.267756] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID C54E2 08A-8018-46C3-9E2D-7EA945EA6BD1, small LPT model
[ 8.281131] mount_root: switching to ubifs overlay
[ 8.322622] urandom-seed: Seeding with /etc/urandom.seed
[ 8.552443] procd: - early -
[ 8.554157] procd: - watchdog -
[ 8.921890] lantiq,xrx200-net 1e108000.eth eth0: port 4 lost link
[ 9.229171] procd: - watchdog -
[ 9.231511] procd: - ubus -
[ 9.268963] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.285156] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.290750] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.298421] procd: - init -
Please press Enter to activate this console.
[ 9.783623] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.792786] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 9.802512] NET: Registered protocol family 8
[ 9.805418] NET: Registered protocol family 20
[ 9.816063] PPP generic driver version 2.4.2
[ 9.825616] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.004196] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
[ 10.015070]
[ 10.015070]
[ 10.015070] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[ 10.032745]
[ 10.032745] Predefined debug level: 3
[ 10.044398] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 10.051086] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 10.060742] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.208217] Infineon Technologies DEU driver version 2.0.0
[ 10.214148] IFX DEU DES initialized (multiblock).
[ 10.218769] IFX DEU AES initialized (multiblock).
[ 10.222784] IFX DEU ARC4 initialized (multiblock).
[ 10.227269] IFX DEU SHA1 initialized.
[ 10.230926] IFX DEU MD5 initialized.
[ 10.234459] IFX DEU SHA1_HMAC initialized.
[ 10.238560] IFX DEU MD5_HMAC initialized.
[ 10.250817] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 10.382643] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 10.390088] owl-loader 0000:00:0e.0: fixup device configuration
[ 10.398372] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 10.404597] NET: Registered protocol family 24
[ 10.428972] xt_time: kernel timezone is -0000
[ 10.750683] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1
[ 10.755924] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
[ 10.763346] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 10.767975] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
[ 10.773848] ath10k_pci 0000:02:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 10.995965] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal- pci-0000:02:00.0.bin failed with error -2
[ 11.005326] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 11.199103] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_st ore: map pages failed
[ 11.208706] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/ hw2.0/firmware-6.bin failed with error -2
[ 11.218119] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 11.471656] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_st ore: map pages failed
[ 11.484566] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 11.492540] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 11.511733] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00037 api 5 feat ures no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb
[ 11.555427] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/ hw2.0/board-2.bin failed with error -2
[ 11.564581] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 11.760937] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store : map pages failed
[ 11.769177] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c 08
[ 12.820934] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file m ax-sta 128 raw 0 hwcrypto 1
[ 12.985102] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 12.996278] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
[ 13.027528] ieee80211 phy1: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30
[ 13.036287] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.612461] urandom_read: 5 callbacks suppressed
[ 14.612477] random: jshn: uninitialized urandom read (4 bytes read)
[ 21.795965] random: crng init done
[ 23.092444] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.104052] device eth0 entered promiscuous mode
[ 23.110392] br-lan: port 1(eth0.1) entered blocking state
[ 23.114511] br-lan: port 1(eth0.1) entered disabled state
[ 23.120452] device eth0.1 entered promiscuous mode
[ 23.129536] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 27.194287] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link
[ 27.199060] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.207626] br-lan: port 1(eth0.1) entered blocking state
[ 27.211655] br-lan: port 1(eth0.1) entered forwarding state
[ 27.220006] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
