Guest Wi-Fi on a wireless AP using LuCI

Installing and Using OpenWrt Network and Wireless Configuration
1

Unfortunately I am unable to set up a guest network by following the instructions at the following link: https://openwrt.org/docs/guide-user/network/wifi/guestwifi/guestwifi_dumbap

I am using OpenWrt 19.07.4, r11208-ce6496d796 on the Linksys WRT1900ACS.

I am able to follow all of the steps in the guide, but when I connect to the Guest network, there is no internet access.

I have attached my configuration data below.

network

config interface 'loopback'
	option ifname 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fdcc:f3fa:65a7::/48'

config interface 'lan'
	option type 'bridge'
	option ifname 'eth0.1'
	option proto 'static'
	option ipaddr '192.168.1.1'
	option netmask '255.255.255.0'
	option ip6assign '60'

config interface 'wan'
	option ifname 'eth1.2'
	option proto 'dhcp'

config interface 'wan6'
	option ifname 'eth1.2'
	option proto 'dhcpv6'

config switch
	option name 'switch0'
	option reset '1'
	option enable_vlan '1'

config switch_vlan
	option device 'switch0'
	option vlan '1'
	option ports '0 1 2 3 5t'

config switch_vlan
	option device 'switch0'
	option vlan '2'
	option ports '4 6t'

config interface 'guest'
	option proto 'static'
	option ipaddr '192.168.2.1'
	option netmask '255.255.255.0'

firewall

config defaults
	option input 'ACCEPT'
	option output 'ACCEPT'
	option forward 'REJECT'
	option synflood_protect '1'

config zone
	option name 'lan'
	list network 'lan'
	option input 'ACCEPT'
	option output 'ACCEPT'
	option forward 'ACCEPT'
	option masq '1'

config zone
	option name 'wan'
	list network 'wan'
	list network 'wan6'
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	option masq '1'
	option mtu_fix '1'

config forwarding
	option src 'lan'
	option dest 'wan'

config rule
	option name 'Allow-DHCP-Renew'
	option src 'wan'
	option proto 'udp'
	option dest_port '68'
	option target 'ACCEPT'
	option family 'ipv4'

config rule
	option name 'Allow-Ping'
	option src 'wan'
	option proto 'icmp'
	option icmp_type 'echo-request'
	option family 'ipv4'
	option target 'ACCEPT'

config rule
	option name 'Allow-IGMP'
	option src 'wan'
	option proto 'igmp'
	option family 'ipv4'
	option target 'ACCEPT'

config rule
	option name 'Allow-DHCPv6'
	option src 'wan'
	option proto 'udp'
	option src_ip 'fc00::/6'
	option dest_ip 'fc00::/6'
	option dest_port '546'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-MLD'
	option src 'wan'
	option proto 'icmp'
	option src_ip 'fe80::/10'
	list icmp_type '130/0'
	list icmp_type '131/0'
	list icmp_type '132/0'
	list icmp_type '143/0'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-ICMPv6-Input'
	option src 'wan'
	option proto 'icmp'
	list icmp_type 'echo-request'
	list icmp_type 'echo-reply'
	list icmp_type 'destination-unreachable'
	list icmp_type 'packet-too-big'
	list icmp_type 'time-exceeded'
	list icmp_type 'bad-header'
	list icmp_type 'unknown-header-type'
	list icmp_type 'router-solicitation'
	list icmp_type 'neighbour-solicitation'
	list icmp_type 'router-advertisement'
	list icmp_type 'neighbour-advertisement'
	option limit '1000/sec'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-ICMPv6-Forward'
	option src 'wan'
	option dest '*'
	option proto 'icmp'
	list icmp_type 'echo-request'
	list icmp_type 'echo-reply'
	list icmp_type 'destination-unreachable'
	list icmp_type 'packet-too-big'
	list icmp_type 'time-exceeded'
	list icmp_type 'bad-header'
	list icmp_type 'unknown-header-type'
	option limit '1000/sec'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-IPSec-ESP'
	option src 'wan'
	option dest 'lan'
	option proto 'esp'
	option target 'ACCEPT'

config rule
	option name 'Allow-ISAKMP'
	option src 'wan'
	option dest 'lan'
	option dest_port '500'
	option proto 'udp'
	option target 'ACCEPT'

config include
	option path '/etc/firewall.user'

config zone
	option network 'guest'
	option forward 'REJECT'
	option name 'guest'
	option output 'ACCEPT'
	option input 'REJECT'

config forwarding
	option dest 'lan'
	option src 'guest'

config rule
	option dest_port '67-68'
	option src 'guest'
	option name 'Guest DHCP'
	option target 'ACCEPT'
	list proto 'udp'

config rule
	option dest_port '53'
	option src 'guest'
	option name 'Guest DNS'
	option target 'ACCEPT'

config rule
	option src 'guest'
	option name 'Block Guest Access to Private Network'
	option dest 'lan'
	list dest_ip '192.168.1.0/24'
	option target 'DROP'

dhcp

config dnsmasq
	option domainneeded '1'
	option boguspriv '1'
	option filterwin2k '0'
	option localise_queries '1'
	option rebind_protection '1'
	option rebind_localhost '1'
	option local '/lan/'
	option domain 'lan'
	option expandhosts '1'
	option nonegcache '0'
	option authoritative '1'
	option readethers '1'
	option leasefile '/tmp/dhcp.leases'
	option resolvfile '/tmp/resolv.conf.auto'
	option nonwildcard '1'
	option localservice '1'

config dhcp 'lan'
	option interface 'lan'
	option start '100'
	option limit '150'
	option leasetime '12h'
	option dhcpv6 'server'
	option ra 'server'

config dhcp 'wan'
	option interface 'wan'
	option ignore '1'

config odhcpd 'odhcpd'
	option maindhcp '0'
	option leasefile '/tmp/hosts/odhcpd'
	option leasetrigger '/usr/sbin/odhcpd-update'
	option loglevel '4'

config dhcp 'guest'
	option start '100'
	option leasetime '12h'
	option limit '150'
	option interface 'guest'

Is there something in the guide that is wrong? Or did I miss a step somewhere? I have tried this a few times with a clean reset of the firmware to just make sure I hadn't somehow messed things up.

2

Post the output:

ip address show; ip route show; ip rule show
3

You have enable forwarding from GUEST to LAN, then blocked it. And you have not enabled any forwarding from GUEST to WAN.

4

Yes, that makes sense! Does the referenced documentation need to be updated? If I forward the Guest network to WAN, everything works, but I wanted to update the documentation if that is the correct method so that others don't get tripped up by the guide.

5

That guide is for a device working as a dumb AP, while yours seems to be running as a router.

2 Likes
6

Oh that makes total sense! So, all I need to do for my set up is forward the guest network to the wan? Do I turn off masquerading for the LAN in that case? Thank you!

7

Yes and yes.

1 Like
8

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.