mk24
63
This sounds like your serial input to the router is not working. Check your serial adapter by connecting Tx and Rx together (not to a router). You should see what you type. Breaking the connection, you should not see what you type.
Besides checking the hardware, make sure the PC software is set for flow control None.
Thanks mk24 for this guide...
wireless can be enabled via console by typing:
uci set wireless.radio0.disabled=0
uci commit
reboot
I will try to make new flash images with actual Openwrt version.
a then test it into my router.
[ 29.392356] br-lan: port 1(eth0.1) entered forwarding state
[ 29.403646] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 30.222376] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 33.830806] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 33.846445] NFSD: starting 10-second grace period (net 80477168)
aaaaaaaaaaaabbbbbbbbbbbbbbb mk24 mk24 JRD_mClaren[
if I disconnect the adapter, I can write
ok I connected and can write 
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 19.07.1, r10911-c155900f66
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# root[ 38.986524] br-lan: port 1(eth0.1) entered blocking state
[ 38.997466] br-lan: port 1(eth0.1) entered disabled state
[ 39.008560] device eth0.1 entered promiscuous mode
[ 39.018091] device eth0 entered promiscuous mode
[ 39.139667] br-lan: port 1(eth0.1) entered blocking state
[ 39.150432] br-lan: port 1(eth0.1) entered forwarding state
[ 39.161740] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 40.054804] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 43.621845] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 43.637497] NFSD: starting 10-second grace period (net 80477168)
/bin/ash: root: not found
root@OpenWrt:/# root
/bin/ash: root: not found
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr 8A:2E:11:77:0E:66
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fdc2:5f9:cb08::1/60 Scope:Global
inet6 addr: fe80::882e:11ff:fe77:e66/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1964 (1.9 KiB)
eth0 Link encap:Ethernet HWaddr 8A:2E:11:77:0E:66
inet6 addr: fe80::882e:11ff:fe77:e66/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:54 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:9795 (9.5 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr 8A:2E:11:77:0E:66
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1964 (1.9 KiB)
eth0.2 Link encap:Ethernet HWaddr 8A:2E:11:77:0E:67
inet6 addr: fe80::882e:11ff:fe77:e67/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:5220 (5.0 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:42 errors:0 dropped:0 overruns:0 frame:0
TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2860 (2.7 KiB) TX bytes:2860 (2.7 KiB)
root@OpenWrt:/#
try this
and then you can see OpenWrt wifi
root@OpenWrt:/# [ 89.714268] device wlan0 left promiscuous mode
[ 89.723282] br-lan: port 2(wlan0) entered disabled state
[ 97.709382] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 97.748398] br-lan: port 2(wlan0) entered blocking state
[ 97.759001] br-lan: port 2(wlan0) entered disabled state
[ 97.769933] device wlan0 entered promiscuous mode
[ 97.814360] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 97.827236] br-lan: port 2(wlan0) entered blocking state
[ 97.837805] br-lan: port 2(wlan0) entered forwarding state
[ 107.986012] device wlan0 left promiscuous mode
[ 107.995031] br-lan: port 2(wlan0) entered disabled state
[ 108.660180] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 108.698921] br-lan: port 2(wlan0) entered blocking state
[ 108.709524] br-lan: port 2(wlan0) entered disabled state
[ 108.720448] device wlan0 entered promiscuous mode
[ 108.729956] br-lan: port 2(wlan0) entered blocking state
[ 108.740509] br-lan: port 2(wlan0) entered forwarding state
[ 108.786515] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
I turn the wifi on and off, but I can't see it on the pc
Oooou ...
Something is wrong...
Ethernet ports does not work after factory reset ...
(or firmware upgrade) ...
Now I must find ..WHY ...
type ' uci show ' in console ...and try to find and post
wireless.radio0 settings
You’ve reached the maximum number of replies a new user can create on their first day. Please wait 18 hours before trying again.
new login
root@OpenWrt:/# uci show
ddns.global=ddns
ddns.global.ddns_dateformat='%F %R'
ddns.global.ddns_loglines='250'
ddns.global.upd_privateip='0'
ddns.myddns_ipv4=service
ddns.myddns_ipv4.lookup_host='yourhost.example.com'
ddns.myddns_ipv4.domain='yourhost.example.com'
ddns.myddns_ipv4.username='your_username'
ddns.myddns_ipv4.password='your_password'
ddns.myddns_ipv4.interface='wan'
ddns.myddns_ipv4.ip_source='network'
ddns.myddns_ipv4.ip_network='wan'
ddns.myddns_ipv4.service_name='dyn.com'
ddns.myddns_ipv6=service
ddns.myddns_ipv6.update_url='http://[USERNAME]:[PASSWORD]@your.provider.net/nic/update?hostname=[DOMAIN]&myip=[IP]'
ddns.myddns_ipv6.lookup_host='yourhost.example.com'
ddns.myddns_ipv6.domain='yourhost.example.com'
ddns.myddns_ipv6.username='your_username'
ddns.myddns_ipv6.password='your_password'
ddns.myddns_ipv6.use_ipv6='1'
ddns.myddns_ipv6.interface='wan6'
ddns.myddns_ipv6.ip_source='network'
ddns.myddns_ipv6.ip_network='wan6'
dhcp.@dnsmasq[0]=dnsmasq
dhcp.@dnsmasq[0].domainneeded='1'
dhcp.@dnsmasq[0].boguspriv='1'
dhcp.@dnsmasq[0].filterwin2k='0'
dhcp.@dnsmasq[0].localise_queries='1'
dhcp.@dnsmasq[0].rebind_protection='1'
dhcp.@dnsmasq[0].rebind_localhost='1'
dhcp.@dnsmasq[0].local='/lan/'
dhcp.@dnsmasq[0].domain='lan'
dhcp.@dnsmasq[0].expandhosts='1'
dhcp.@dnsmasq[0].nonegcache='0'
dhcp.@dnsmasq[0].authoritative='1'
dhcp.@dnsmasq[0].readethers='1'
dhcp.@dnsmasq[0].leasefile='/tmp/dhcp.leases'
dhcp.@dnsmasq[0].resolvfile='/tmp/resolv.conf.auto'
dhcp.@dnsmasq[0].nonwildcard='1'
dhcp.@dnsmasq[0].localservice='1'
dhcp.lan=dhcp
dhcp.lan.interface='lan'
dhcp.lan.start='100'
dhcp.lan.limit='150'
dhcp.lan.leasetime='12h'
dhcp.lan.dhcpv6='server'
dhcp.lan.ra='server'
dhcp.wan=dhcp
dhcp.wan.interface='wan'
dhcp.wan.ignore='1'
dhcp.odhcpd=odhcpd
dhcp.odhcpd.maindhcp='0'
dhcp.odhcpd.leasefile='/tmp/hosts/odhcpd'
dhcp.odhcpd.leasetrigger='/usr/sbin/odhcpd-update'
dhcp.odhcpd.loglevel='4'
dropbear.@dropbear[0]=dropbear
dropbear.@dropbear[0].PasswordAuth='on'
dropbear.@dropbear[0].RootPasswordAuth='on'
dropbear.@dropbear[0].Port='22'
firewall.@defaults[0]=defaults
firewall.@defaults[0].syn_flood='1'
firewall.@defaults[0].input='ACCEPT'
firewall.@defaults[0].output='ACCEPT'
firewall.@defaults[0].forward='REJECT'
firewall.@zone[0]=zone
firewall.@zone[0].name='lan'
firewall.@zone[0].network='lan'
firewall.@zone[0].input='ACCEPT'
firewall.@zone[0].output='ACCEPT'
firewall.@zone[0].forward='ACCEPT'
firewall.@zone[1]=zone
firewall.@zone[1].name='wan'
firewall.@zone[1].network='wan' 'wan6'
firewall.@zone[1].input='REJECT'
firewall.@zone[1].output='ACCEPT'
firewall.@zone[1].forward='REJECT'
firewall.@zone[1].masq='1'
firewall.@zone[1].mtu_fix='1'
firewall.@forwarding[0]=forwarding
firewall.@forwarding[0].src='lan'
firewall.@forwarding[0].dest='wan'
firewall.@rule[0]=rule
firewall.@rule[0].name='Allow-DHCP-Renew'
firewall.@rule[0].src='wan'
firewall.@rule[0].proto='udp'
firewall.@rule[0].dest_port='68'
firewall.@rule[0].target='ACCEPT'
firewall.@rule[0].family='ipv4'
firewall.@rule[1]=rule
firewall.@rule[1].name='Allow-Ping'
firewall.@rule[1].src='wan'
firewall.@rule[1].proto='icmp'
firewall.@rule[1].icmp_type='echo-request'
firewall.@rule[1].family='ipv4'
firewall.@rule[1].target='ACCEPT'
firewall.@rule[2]=rule
firewall.@rule[2].name='Allow-IGMP'
firewall.@rule[2].src='wan'
firewall.@rule[2].proto='igmp'
firewall.@rule[2].family='ipv4'
firewall.@rule[2].target='ACCEPT'
firewall.@rule[3]=rule
firewall.@rule[3].name='Allow-DHCPv6'
firewall.@rule[3].src='wan'
firewall.@rule[3].proto='udp'
firewall.@rule[3].src_ip='fc00::/6'
firewall.@rule[3].dest_ip='fc00::/6'
firewall.@rule[3].dest_port='546'
firewall.@rule[3].family='ipv6'
firewall.@rule[3].target='ACCEPT'
firewall.@rule[4]=rule
firewall.@rule[4].name='Allow-MLD'
firewall.@rule[4].src='wan'
firewall.@rule[4].proto='icmp'
firewall.@rule[4].src_ip='fe80::/10'
firewall.@rule[4].icmp_type='130/0' '131/0' '132/0' '143/0'
firewall.@rule[4].family='ipv6'
firewall.@rule[4].target='ACCEPT'
firewall.@rule[5]=rule
firewall.@rule[5].name='Allow-ICMPv6-Input'
firewall.@rule[5].src='wan'
firewall.@rule[5].proto='icmp'
firewall.@rule[5].icmp_type='echo-request' 'echo-reply' 'destination-unreachable' 'packet-too-big' 'time-exceeded' 'bad-header' 'unknown-header-type' 'router-solicitation' 'neighbour-solicitation' 'router-advertisement' 'neighbour-advertisement'
firewall.@rule[5].limit='1000/sec'
firewall.@rule[5].family='ipv6'
firewall.@rule[5].target='ACCEPT'
firewall.@rule[6]=rule
firewall.@rule[6].name='Allow-ICMPv6-Forward'
firewall.@rule[6].src='wan'
firewall.@rule[6].dest='*'
firewall.@rule[6].proto='icmp'
firewall.@rule[6].icmp_type='echo-request' 'echo-reply' 'destination-unreachable' 'packet-too-big' 'time-exceeded' 'bad-header' 'unknown-header-type'
firewall.@rule[6].limit='1000/sec'
firewall.@rule[6].family='ipv6'
firewall.@rule[6].target='ACCEPT'
firewall.@rule[7]=rule
firewall.@rule[7].name='Allow-IPSec-ESP'
firewall.@rule[7].src='wan'
firewall.@rule[7].dest='lan'
firewall.@rule[7].proto='esp'
firewall.@rule[7].target='ACCEPT'
firewall.@rule[8]=rule
firewall.@rule[8].name='Allow-ISAKMP'
firewall.@rule[8].src='wan'
firewall.@rule[8].dest='lan'
firewall.@rule[8].dest_port='500'
firewall.@rule[8].proto='udp'
firewall.@rule[8].target='ACCEPT'
firewall.@include[0]=include
firewall.@include[0].path='/etc/firewall.user'
fstab.@global[0]=global
fstab.@global[0].anon_swap='0'
fstab.@global[0].anon_mount='0'
fstab.@global[0].auto_swap='1'
fstab.@global[0].auto_mount='1'
fstab.@global[0].delay_root='5'
fstab.@global[0].check_fs='0'
luci.main=core
luci.main.lang='auto'
luci.main.mediaurlbase='/luci-static/bootstrap'
luci.main.resourcebase='/luci-static/resources'
luci.flash_keep=extern
luci.flash_keep.uci='/etc/config/'
luci.flash_keep.dropbear='/etc/dropbear/'
luci.flash_keep.openvpn='/etc/openvpn/'
luci.flash_keep.passwd='/etc/passwd'
luci.flash_keep.opkg='/etc/opkg.conf'
luci.flash_keep.firewall='/etc/firewall.user'
luci.flash_keep.uploads='/lib/uci/upload/'
luci.languages=internal
luci.sauth=internal
luci.sauth.sessionpath='/tmp/luci-sessions'
luci.sauth.sessiontime='3600'
luci.ccache=internal
luci.ccache.enable='1'
luci.themes=internal
luci.themes.Bootstrap='/luci-static/bootstrap'
luci.apply=internal
luci.apply.rollback='90'
luci.apply.holdoff='4'
luci.apply.timeout='5'
luci.apply.display='1.5'
luci.diag=internal
luci.diag.dns='openwrt.org'
luci.diag.ping='openwrt.org'
luci.diag.route='openwrt.org'
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fdc2:05f9:cb08::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0.1'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan_eth0_1_dev=device
network.lan_eth0_1_dev.name='eth0.1'
network.lan_eth0_1_dev.macaddr='8a:2e:11:77:0e:66'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.proto='dhcp'
network.wan_eth0_2_dev=device
network.wan_eth0_2_dev.name='eth0.2'
network.wan_eth0_2_dev.macaddr='8a:2e:11:77:0e:67'
network.wan6=interface
network.wan6.ifname='eth0.2'
network.wan6.proto='dhcpv6'
p910nd.@p910nd[0]=p910nd
p910nd.@p910nd[0].device='/dev/usb/lp0'
p910nd.@p910nd[0].port='0'
p910nd.@p910nd[0].bidirectional='1'
p910nd.@p910nd[0].enabled='0'
p910nd.@p910nd[0].runas_root='0'
p910nd.@p910nd[0].mdns='0'
p910nd.@p910nd[0].mdns_ty='My Printer Manufacturer/Model'
p910nd.@p910nd[0].mdns_note='Basement'
rpcd.@rpcd[0]=rpcd
rpcd.@rpcd[0].socket='/var/run/ubus.sock'
rpcd.@rpcd[0].timeout='30'
rpcd.@login[0]=login
rpcd.@login[0].username='root'
rpcd.@login[0].password='$p$root'
rpcd.@login[0].read='*'
rpcd.@login[0].write='*'
system.@system[0]=system
system.@system[0].hostname='OpenWrt'
system.@system[0].timezone='UTC'
system.@system[0].ttylogin='0'
system.@system[0].log_size='64'
system.@system[0].urandom_seed='0'
system.ntp=timeserver
system.ntp.enabled='1'
system.ntp.enable_server='0'
system.ntp.server='0.openwrt.pool.ntp.org' '1.openwrt.pool.ntp.org' '2.openwrt.pool.ntp.org' '3.openwrt.pool.ntp.org'
ucitrack.@network[0]=network
ucitrack.@network[0].init='network'
ucitrack.@network[0].affects='dhcp' 'radvd'
ucitrack.@wireless[0]=wireless
ucitrack.@wireless[0].affects='network'
ucitrack.@firewall[0]=firewall
ucitrack.@firewall[0].init='firewall'
ucitrack.@firewall[0].affects='luci-splash' 'qos' 'miniupnpd'
ucitrack.@olsr[0]=olsr
ucitrack.@olsr[0].init='olsrd'
ucitrack.@dhcp[0]=dhcp
ucitrack.@dhcp[0].init='dnsmasq'
ucitrack.@dhcp[0].affects='odhcpd'
ucitrack.@odhcpd[0]=odhcpd
ucitrack.@odhcpd[0].init='odhcpd'
ucitrack.@dropbear[0]=dropbear
ucitrack.@dropbear[0].init='dropbear'
ucitrack.@httpd[0]=httpd
ucitrack.@httpd[0].init='httpd'
ucitrack.@fstab[0]=fstab
ucitrack.@fstab[0].exec='/sbin/block mount'
ucitrack.@qos[0]=qos
ucitrack.@qos[0].init='qos'
ucitrack.@system[0]=system
ucitrack.@system[0].init='led'
ucitrack.@system[0].exec='/etc/init.d/log reload'
ucitrack.@system[0].affects='luci_statistics' 'dhcp'
ucitrack.@luci_splash[0]=luci_splash
ucitrack.@luci_splash[0].init='luci_splash'
ucitrack.@upnpd[0]=upnpd
ucitrack.@upnpd[0].init='miniupnpd'
ucitrack.@ntpclient[0]=ntpclient
ucitrack.@ntpclient[0].init='ntpclient'
ucitrack.@samba[0]=samba
ucitrack.@samba[0].init='samba'
ucitrack.@tinyproxy[0]=tinyproxy
ucitrack.@tinyproxy[0].init='tinyproxy'
ucitrack.@p910nd[0]=p910nd
ucitrack.@p910nd[0].init='p910nd'
uhttpd.main=uhttpd
uhttpd.main.listen_http='0.0.0.0:80' '[::]:80'
uhttpd.main.listen_https='0.0.0.0:443' '[::]:443'
uhttpd.main.redirect_https='1'
uhttpd.main.home='/www'
uhttpd.main.rfc1918_filter='1'
uhttpd.main.max_requests='3'
uhttpd.main.max_connections='100'
uhttpd.main.cert='/etc/uhttpd.crt'
uhttpd.main.key='/etc/uhttpd.key'
uhttpd.main.cgi_prefix='/cgi-bin'
uhttpd.main.lua_prefix='/cgi-bin/luci=/usr/lib/lua/luci/sgi/uhttpd.lua'
uhttpd.main.script_timeout='60'
uhttpd.main.network_timeout='30'
uhttpd.main.http_keepalive='20'
uhttpd.main.tcp_keepalive='1'
uhttpd.defaults=cert
uhttpd.defaults.days='730'
uhttpd.defaults.key_type='rsa'
uhttpd.defaults.bits='2048'
uhttpd.defaults.ec_curve='P-256'
uhttpd.defaults.country='ZZ'
uhttpd.defaults.state='Somewhere'
uhttpd.defaults.location='Unknown'
uhttpd.defaults.commonname='OpenWrt'
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.channel='11'
wireless.radio0.hwmode='11g'
wireless.radio0.path='platform/10300000.wmac'
wireless.radio0.htmode='HT20'
wireless.radio0.disabled='0'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.ssid='OpenWrt'
wireless.default_radio0.encryption='none'
root@OpenWrt:/#
Hi how to re-upload soft openwrt-19.07.0-ramips-mt76x8-ytxc-958-squashfs-sysupgrade by putty?
So .. I'm there ..
You can't see wifi network ..?? OpenWrt
you can load firmware image via TFTP server ..
My firmware image has problem with switch and vlan configuration.
"SWITCH" option is not visible in LUCi..
so .. eth0.1 and eth0.2 does not work ..
Can anybody help me with this issue ..??
I have a static ip address of 192.168.1.100
but if I connect the router, it's a bad interface
and I can't load the software
1: System Load Linux to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (10.10.10.123) ==:192.168.1.1
Input server IP (10.10.10.3) ==:192.168.1.100
Input Linux Kernel filename () ==:as.bin
netboot_common, argc= 3
NetTxPacket = 0x83FE5AC0
KSEG1ADDR(NetTxPacket) = 0xA3FE5AC0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'as.bin'.
TIMEOUT_COUNT=10,Load address: 0x80a00000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
T T T Got ARP REQUEST, return our IP
Got ARP REQUEST, return our IP
ArpTimeoutCheck
T Got ARP REQUEST, return our IP
T T
I changed the ip in the router to 192.168.20.1 but still the same is not connected
I have no idea, what's wrong in SWITCH settings after FACTORY RESET ...
..or first firmware flash ...
gustawa21, would you can edit /etc/config/network file ..?? (on router)
and add these lines:
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '0 1 2 3 6t'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '4 6t'
and then try to restart network ...
/etc/init.d/./network restart
root@OpenWrt:/# vi /etc/config/network
root@OpenWrt:/# /etc/init.d/./network restart
'radio0' is disabled
[ 337.520180] br-lan: port 1(eth0.1) entered disabled state
[ 337.552882] device eth0.1 left promiscuous mode
[ 337.562112] br-lan: port 1(eth0.1) entered disabled state
[ 337.586345] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 337.986543] device eth0 left promiscuous mode
Failed to load config file: : Parse error (EOF with unterminated ') at line 47, byte 27
root@OpenWrt:/# [ 342.755832] device eth0 entered promiscuous mode
[ 342.777321] br-lan: port 1(eth0.1) entered blocking state
[ 342.788092] br-lan: port 1(eth0.1) entered disabled state
[ 342.799177] device eth0.1 entered promiscuous mode
[ 342.868106] br-lan: port 1(eth0.1) entered blocking state
[ 342.878871] br-lan: port 1(eth0.1) entered forwarding state
[ 342.890145] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 343.822384] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 368.009432] rt3050-esw 10110000.esw: link changed 0x01
[ 371.040472] rt3050-esw 10110000.esw: link changed 0x01
[ 374.104280] rt3050-esw 10110000.esw: link changed 0x01
[ 376.594647] rt3050-esw 10110000.esw: link changed 0x01
[ 381.575383] rt3050-esw 10110000.esw: link changed 0x01
[ 384.110025] rt3050-esw 10110000.esw: link changed 0x01
[ 422.267223] rt3050-esw 10110000.esw: link changed 0x00
[ 424.419532] rt3050-esw 10110000.esw: link changed 0x01
[ 427.466966] rt3050-esw 10110000.esw: link changed 0x01
[ 430.514390] rt3050-esw 10110000.esw: link changed 0x01
[ 435.496406] rt3050-esw 10110000.esw: link changed 0x01
[ 437.985493] rt3050-esw 10110000.esw: link changed 0x01
[ 440.516625] rt3050-esw 10110000.esw: link changed 0x01
[ 511.723862] rt3050-esw 10110000.esw: link changed 0x00
[ 540.696789] rt3050-esw 10110000.esw: link changed 0x01
[ 543.744211] rt3050-esw 10110000.esw: link changed 0x01
[ 546.775251] rt3050-esw 10110000.esw: link changed 0x01
[ 549.282004] rt3050-esw 10110000.esw: link changed 0x01
[ 554.263765] rt3050-esw 10110000.esw: link changed 0x01
[ 556.789427] rt3050-esw 10110000.esw: link changed 0x01
28/5000
the same but I see some error
sorry I have some error in my last post ...
add one " ' " on last line in network file
and restart it again ..
now I working on new image file ...
I'm just learning and I don't really understand what to add ?
ok I added option ports '4 6t'
root@OpenWrt:/# vi /etc/config/network
root@OpenWrt:/# /etc/init.d/./network restart
'radio0' is disabled
[ 209.009146] br-lan: port 1(eth0.1) entered disabled state
[ 209.041760] device eth0.1 left promiscuous mode
[ 209.050991] br-lan: port 1(eth0.1) entered disabled state
[ 209.075525] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 209.477852] device eth0 left promiscuous mode
root@OpenWrt:/# [ 214.265879] device eth0 entered promiscuous mode
[ 214.282793] br-lan: port 1(eth0.1) entered blocking state
[ 214.293562] br-lan: port 1(eth0.1) entered disabled state
[ 214.304642] device eth0.1 entered promiscuous mode
[ 214.374144] br-lan: port 1(eth0.1) entered blocking state
[ 214.384909] br-lan: port 1(eth0.1) entered forwarding state
[ 214.396203] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 215.262389] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 221.072147] rt3050-esw 10110000.esw: link changed 0x01
[ 224.103187] rt3050-esw 10110000.esw: link changed 0x01
[ 227.134227] rt3050-esw 10110000.esw: link changed 0x01
[ 229.624595] rt3050-esw 10110000.esw: link changed 0x01
[ 234.605331] rt3050-esw 10110000.esw: link changed 0x01
[ 237.139021] rt3050-esw 10110000.esw: link changed 0x01
ok, I added but I still do not want to connect and the cable is good tp
..I'm not shure...
try and post
uci show network
uci show wireless
