Hi,
installed the last @r00t VS, I would like a help, because I found the response times slow and in the network configurations, use PPPoE the MAC address disappeared (see photo), and sorry the basic question, but since I read information contradictory, after installing FACTORY.bin, and do I need to install SYSUPGRADE?
I'm counting on you to help fine tune my setup.
thanks
Guedes
Checking the output of the DMESG I checked these errors in red, how to correct them?
19.174881] fast-classifier: starting up
[ 19.179062] fast-classifier: registered
[ 19.298113] PPP generic driver version 2.4.2
[ 19.316071] PPP MPPE Compression module registered
[ 19.333928] NET: Registered protocol family 24
[ 19.346834] PPTP driver version 0.8.5
[ 19.413591] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 19.419559] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 19.639745] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 19.650647] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 19.704311] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 19.821199] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 19.832100] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 19.904686] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 20.228001] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 20.237409] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 1 testmode 1
[ 20.250475] ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[ 20.298364] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 20.308984] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 20.363585] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 20.394670] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 21.466415] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 21.577453] ath: EEPROM regdomain: 0x0
[ 21.577459] ath: EEPROM indicates default country code should be used
[ 21.577462] ath: doing EEPROM country->regdmn map search
[ 21.577473] ath: country maps to regdmn code: 0x3a
[ 21.577477] ath: Country alpha2 being used: US
[ 21.577481] ath: Regpair used: 0x3a
[ 21.702372] l2tp_ppp: PPPoL2TP kernel driver, V2.0how is it running? once you have flashed the factory.bin, you only use sysupgrade.bin to upgrade versions for the individual router, currently in @r00t NIGHTLY folder on his github is the latest compiled backport of 4.9.65, so feel free to upgrade by flashing with the sysupgrade.bin file. It''s working great, he does a new compile about every 2-3 days or so. I have google home firesticks chromecasts etc all running on 5ghz, i never have an issue with buffering or anything atm. But i also use a raspberry pi for dns requests which helps with the load i think, rather than using simple adblock i remove that and run a pi hole ads blocker, seems to run without a hitch. I also use a 2.0 usb for /overlay which i believe helps the load too.
Hello,
thanks to the answer, its configuration and similar to mine, I use Archer / LEDE to manage the network with 2 smartTV, 2 phones, tablet and 4 computers, currently the main focus is on TV, because I use IPVT by software, There is no ISP that offers this service.
I put an 8GB USB to help the router manage everything, but I think I have not yet set this configuration, I am researching and reading the documentation of the LEDE site and forums on the subject, the update I will do today and see if I delete the MSG errors during boot.
And I will post the doubts and results because I know that I have the help of friends, and the answers and results can help someone else at another time.
thank you all for the help given in the forum, and we go ahead
update for last vs done!
but.....
Linux version 4.9.65 (r00t@skynet) (gcc version 7.2.0 (LEDE GCC 7.2.0 r5264-94491a1571) ) #0 Tue Nov 28 19:59:02 2017
I hope can help for next build
EDIT: after the last update the results of the speed test improved
17.01.4 archer c7 version 2 this is some what of a write up i did on external root for usb. i dont think the red lettering is an error i think its just informing you that fast classifier has started and registered with the device. Anyways hope it helps
apparently everything is working well, but I will investigate this "error"
BTW
Is there an addon to read the temperature of the router?
I saw that in DD-WRT it shows the temp. of the 5ghz wifi card, would it be possible to have something in the LEDE?
i havent seen anything and with the current build python isnt working so i cant use any 3rd party modules which sucks.
Just loaded this build... yes I know I am very late to the party and I am also completely new to LEDE but here goes:
I wanted to load usb printer support and followed the following tutorials:
Loaded usb support using this process:
The tried to load the actual usb printer support via this tutorial:
When typing in the line opkg install kmod-usb-printer kmod-lp p910nd I get the following output:
Installing kmod-usb-printer (4.9.65-1) to root...
Downloading http://downloads.lede-project.org/snapshots/targets/ar71xx/generic/packages/kmod-usb-printer_4.9.65-1_mips_24kc.ipk
Installing kmod-lp (4.9.65-1) to root...
Downloading http://downloads.lede-project.org/snapshots/targets/ar71xx/generic/packages/kmod-lp_4.9.65-1_mips_24kc.ipk
Package p910nd (0.97-5) installed in root is up to date.
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-usb-printer:
* kernel (= 4.9.65-1-1099a298c1a12dff817c08ff1e9b77ed) *
* opkg_install_cmd: Cannot install package kmod-usb-printer.
* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-lp:
* kernel (= 4.9.65-1-1099a298c1a12dff817c08ff1e9b77ed) *
* opkg_install_cmd: Cannot install package kmod-lp.
Now I am not much of an LEDE or LINUX guy but seems to me the kernel needs to be updated or I need a different package. Can someone help?
Just remember I am EXTREMELY inexperienced in BOTH LEDE and in LINUX so please keep it as simple as possible.
Thanks for the fast reply:
Looks to be the same command and gives me the exact same dependency error about kernel version
That seems a little counter intuitive. Someone took the time and effort to take the base and tweak it SPECIFICALLY to our model and version for the sole purpose of making it run better and more efficiently, why would I want to go back to the generic version. Ok I didn't mean it to sound like that let me state another way, If I had to choose between running the optimized or running a printer I would stick to the optimized for the fast path option. I was just hoping I could have both the fast path AND a usb printer.
Update: Found this in github for fastpath
Cannot install packages with Kernel Dependencies?
Use --nodeps in opkg
The builds uses the LEDE upstream repository unfortunately kernel config is hashed so any changes will make it uncompatible
Used that command and everything is now installed but jobs never get to the printer. Looks like since I do not want to lose Fast Path, and I dont believe Fast pPath is in any standard release, I will have to just hook up a jetdirect to the printer and just forget about usb printing.
Hi,
I wast just saying: download the generic build, see if that works.
If it worked, take the patches from the r00t repo, download the LEDE source, and build your own optimized firmware (with your custom packages).
It's not that hard, and takes just 1 hour to compile (core i7 using 8 cores and -j9).
Ok I see what you mean now, unfortunately this router is the sole source for internet for the house thus testing versions would be difficult. But worse then that in order to build as you say once I get the right packages I would assume I would need a linux machine setup for building the firmware and I don't even have a machine running linux currently.
Let me take another tact as I did get it to load but still no jobs get to the printer. My pc side does find the printer (at least no errors setting it up) so I am guessing it might be the device designation or the interface being used in the config on the router side.
Currently lists device as:
/dev/usb/lp0
Interface is set to:
Unspecified though also tried it on lan
Printer is an hp laserjet 2300 running over usb and this entire setup did work on gargoyle 1.10 which is based off of openwrt CC, thus I would think it is not a hardware issue of any kind.
Can someone confirm what the above 2 settings should be. Does the usb port the device is plugged into change the lp designation aka maybe it should be lp1 or lp2
Lastly is there a log somewhere i can look at to see what is happening with the jobs, they simply queue up, say waiting for printer and disappear from the queue. Nothing shows up at the printer at all
hey have you compiled a recent 4.9.67? if so you dont happen to have an upload do you?
@sycohexor
Here's my current build:
https://drive.google.com/file/d/1SuSblpmKfEn16rUtPpFZW2bopVc7fXqP/view?usp=sharing
If you have problems accesing internet, go to the web interface -> services -> DNSCrypt-Proxy and check your settings.
I currently use adguard-dns-ns1.
Btw, I'll use this post to write some things that I've found using LEDE:
New release is up & nightlies fixed (yet again).
kmod-usb-printer <- @adm1jtg
@r00t Thank you so much. I did have to load up luci-app-p910nd, I guess to change a config file as initially the entry/menu option didn't show up, but everything working perfectly now.
Thanks again