I'm having some weird issues with my WRT3200ACM, which I bought in 2016. Long story short, I'm trying to flash the stock firmware onto both partitions using a TTL serial cable.
When I try to do so, I don't get any errors when writing to the nand partitions, but when I boot up, I get stuck in a loop and am unable to access the web GUI. I have tried several firmware versions, all the same exact result.
Strangely, when I flash openWRT firmware onto the router, it DOES work fine, and I am able to access the web gui no problem right away, so I'm assuming Uboot is not the problem. It's only the stock linksys firmware for some reason. I also tried using SSH into OpenWRT to flash the firmware, with the same exact problem and outputs.
I'll paste all the Putty outputs below. As you can see in the 2nd code box (linksys firmware booting), at the end it just keeps looping "sending discover" whatever that means.
A couple possible notable lines / errors.
- "Error occurred at line 25" .
- "Bad block table found at page"... shows up in a couple places
- "Got a TERM signal, will terminate."
- "Warning! nfqrecv encountered errors when doing recv(): Interrupted system call"
Any ideas?
1. Here is the serial output for the uboot and flashing process:
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0
Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01 (Apr 08 2016 - 15:47:50) Marvell version: 2015_T1.QA.0p16
Boot version : v0.0.4
Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1866 [MHz]
L2 @ 933 [MHz]
TClock @ 200 [MHz]
DDR3 @ 933 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0
DEVINFO offset == 0x7e0000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
S-ENV offset == 0x220000
#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3
S-ENV offset == 0x220000
[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:1, next_record:63
[boot_count_write] erase:1, auto_recovery->block_offset:0x220000 offset=0x220000
Updating boot_count ...
[boot_count_write] offset:0x220000 , length:2048
done
PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode
Map: Code:0x1feab000:0x1ff75a20
BSS:0x1ffef164
Stack:0x1f9aaf20
Heap:0x1f9ab000:0x1feab000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
U-Boot Environment:0x00200000:0x00220000 (NAND)
Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 3 2 0
Marvell>> setenv ipaddr 192.168.1.1
Marvell>> setenv serverip 192.168.1.2
Marvell>> setenv firmwarre eName linksys.img
Marvell>> run update_both_images
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'linksys.img'.
Load address: 0x2000000
Loading: *#################################################################
#################################################################
#################################################################
4.2 MiB/s
done
Bytes transferred = 44040448 (2a00100 hex)
NAND erase: device 0 offset 0xa00000, size 0x5000000
Erasing at 0xa00000 -- 0% complete.
Erasing at 0xac0000 -- 1% complete.
[DELETED FOR THREAD]
Erasing at 0x59e0000 -- 100% complete.
OK
NAND erase: device 0 offset 0x5a00000, size 0x5000000
Erasing at 0x5a00000 -- 0% complete.
Erasing at 0x5ac0000 -- 1% complete.
[DELETED FOR THREAD]
Erasing at 0xa9e0000 -- 100% complete.
OK
NAND write: device 0 offset 0xa00000, size 0x2a00100
44040448 bytes written: OK
NAND write: device 0 offset 0x5a00000, size 0x2a00100
44040448 bytes written: OK
Marvell>>
2. Finally, here is the output of the linksys firmware trying to boot (after uboot):
NAND read: device 0 offset 0xa00000, size 0x600000
6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linksys WRT3200 Router
Created: 2019-12-05 23:30:57 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4640879 Bytes = 4.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.70 (root@build-vm) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Thu Dec 5 15:30:40 PST 2019
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvell Armada 385 Development Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1151000 s7488 r8192 d12992 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 1048576 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 508768k/508768k available, 15520k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc08417c8 (8422 kB)
[ 0.000000] .init : 0xc0842000 - 0xc0883d40 ( 264 kB)
[ 0.000000] .data : 0xc0884000 - 0xc08d82a0 ( 337 kB)
[ 0.000000] .bss : 0xc08d82a0 - 0xc099f14c ( 796 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000]
[ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7
[ 0.000000]
[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
[ 0.000000] Console: colour dummy device 80x30
[ 0.017256] Calibrating delay loop... 3726.54 BogoMIPS (lpj=18632704)
[ 0.082983] pid_max: default: 32768 minimum: 301
[ 0.087709] Mount-cache hash table entries: 512
[ 0.092535] Initializing cgroup subsys memory
[ 0.096971] CPU: Testing write buffer coherency: ok
[ 0.102000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.107713] Calibrating local timer... 933.34MHz.
[ 0.171175] Setting up static identity map for 0xc0643018 - 0xc0643070
[ 0.177864] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.184124] Initializing CPU Reset module
[ 0.188628] CPU1: Booted secondary processor
[ 0.241178] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.241230] Brought up 2 CPUs
[ 0.254311] SMP: Total of 2 processors activated (7453.08 BogoMIPS).
[ 0.260715] CPU: All CPU(s) started in SVC mode.
[ 0.265585] devtmpfs: initialized
[ 0.270697] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.276012] xor: measuring software checksum speed
[ 0.371158] arm4regs : 3309.200 MB/sec
[ 0.471160] 8regs : 2234.800 MB/sec
[ 0.571161] 32regs : 1905.600 MB/sec
[ 0.575407] xor: using function: arm4regs (3309.200 MB/sec)
[ 0.581036] pinctrl core: initialized pinctrl subsystem
[ 0.586481] regulator-dummy: no parameters
[ 0.590742] NET: Registered protocol family 16
[ 0.595678] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.604122] irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated
[ 0.611395] irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated
[ 0.628111] bio: create slab <bio-0> at 0
[ 0.801274] raid6: int32x1 232 MB/s
[ 0.971274] raid6: int32x2 344 MB/s
[ 1.141206] raid6: int32x4 437 MB/s
[ 1.311284] raid6: int32x8 444 MB/s
[ 1.315096] raid6: using algorithm int32x8 (444 MB/s)
[ 1.320205] raid6: using intx1 recovery algorithm
[ 1.325172] mvebu-pcie pcie-controller.6: PCIe0.0: link up
[ 1.330727] mvebu-pcie pcie-controller.6: PCIe1.0: link up
[ 1.336350] mvebu-pcie pcie-controller.6: PCI host bridge to bus 0000:00
[ 1.343108] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 1.349428] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 1.356384] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.362145] PCI: bus0: Fast back to back transfers disabled
[ 1.367777] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.375837] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.384118] PCI: bus1: Fast back to back transfers disabled
[ 1.389997] PCI: bus2: Fast back to back transfers disabled
[ 1.395700] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[ 1.402549] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
[ 1.409389] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
[ 1.417192] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
[ 1.424991] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.430015] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe02fffff]
[ 1.436864] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref]
[ 1.444665] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref]
[ 1.452464] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 1.457487] pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe06fffff]
[ 1.464334] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 1.470052] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
[ 1.476086] SCSI subsystem initialized
[ 1.480199] usbcore: registered new interface driver usbfs
[ 1.485786] usbcore: registered new interface driver hub
[ 1.491213] usbcore: registered new device driver usb
[ 1.496509] pps_core: LinuxPPS API ver. 1 registered
[ 1.501535] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.510734] PTP clock support registered
[ 1.515193] Bluetooth: Core ver 2.16
[ 1.518871] NET: Registered protocol family 31
[ 1.523381] Bluetooth: HCI device and connection manager initialized
[ 1.529789] Bluetooth: HCI socket layer initialized
[ 1.534730] Bluetooth: L2CAP socket layer initialized
[ 1.539845] Bluetooth: SCO socket layer initialized
[ 1.544993] Switching to clocksource armada_370_xp_clocksource
[ 1.550894] cfg80211: Calling CRDA to update world regulatory domain
[ 1.561130] NET: Registered protocol family 2
[ 1.565815] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.572947] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.579468] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.585894] TCP: reno registered
[ 1.589190] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.595087] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.601488] NET: Registered protocol family 1
[ 1.605997] RPC: Registered named UNIX socket transport module.
[ 1.611984] RPC: Registered udp transport module.
[ 1.616747] RPC: Registered tcp transport module.
[ 1.621518] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.628864] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.636022] fuse init (API version 7.22)
[ 1.640104] msgmni has been set to 993
[ 1.644223] async_tx: api initialized (async)
[ 1.648684] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 1.656134] io scheduler noop registered
[ 1.660119] io scheduler deadline registered
[ 1.664468] io scheduler cfq registered (default)
[ 1.669602] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 1.676748] mv_xor f1060800.xor: Marvell shared XOR driver
[ 1.721158] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
[ 1.751170] mv_xor f1060800.xor: freeing 1 in use descriptors!
[ 1.757061] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
[ 1.765097] mv_xor f1060900.xor: Marvell shared XOR driver
[ 1.811153] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
[ 1.841151] mv_xor f1060900.xor: freeing 1 in use descriptors!
[ 1.847041] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
[ 1.877916] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.905155] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
[ 1.912270] console [ttyS0] enabled, bootconsole disabled
[ 1.912270] console [ttyS0] enabled, bootconsole disabled
[ 1.923635] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.932473] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.942751] scsi0 : ahci_mv_platform
[ 1.946491] scsi1 : ahci_mv_platform
[ 1.950193] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
[ 1.958151] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
[ 1.966804] armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
[ 1.981185] NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64
[ 1.993888] Bad block table found at page 131008, version 0x01
[ 2.000134] Bad block table found at page 130944, version 0x01
[ 2.006257] 11 cmdlinepart partitions found on MTD device armada-nand
[ 2.012729] Creating 11 MTD partitions on "armada-nand":
[ 2.018063] 0x000000000000-0x000000200000 : "uboot"
[ 2.023303] 0x000000200000-0x000000220000 : "u_env"
[ 2.028486] 0x000000220000-0x000000260000 : "s_env"
[ 2.033678] 0x0000007e0000-0x000000820000 : "devinfo"
[ 2.039039] 0x000000820000-0x000000a00000 : "sysdiag"
[ 2.044418] 0x000000a00000-0x000005a00000 : "kernel"
[ 2.049718] 0x000001000000-0x000005a00000 : "rootfs"
[ 2.055029] 0x000005a00000-0x00000aa00000 : "alt_kernel"
[ 2.060686] 0x000006000000-0x00000aa00000 : "alt_rootfs"
[ 2.066353] 0x000000a00000-0x00000aa00000 : "ubifs"
[ 2.071636] 0x00000aa00000-0x000010000000 : "syscfg"
[ 2.077276] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 2.085960] tun: Universal TUN/TAP device driver, 1.6
[ 2.091041] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.097690] SoC: model = 0x6820, revision = 0x4
[ 2.102290] mvPncVirtBase = 0xe0c00000, pncTcamSize = 1024
[ 2.107796] o 3 Giga ports supported
[ 2.111561] o SKB recycle supported for SWF (Disabled)
[ 2.116891] o NETA acceleration mode 4
[ 2.120826] o BM supported for CPU: 4 BM pools
[ 2.125462] o PnC supported (Enabled)
[ 2.129311] o RX Queue support: 8 Queues * 2048 Descriptors
[ 2.135080] o TX Queue support: 8 Queues * 532 Descriptors
[ 2.140759] o GSO supported
[ 2.143736] o GRO supported
[ 2.146711] o Receive checksum offload supported
[ 2.151521] o Transmit checksum offload supported
[ 2.156415] o Driver ERROR statistics enabled
[ 2.160963] o Driver INFO statistics enabled
[ 2.165420] o Driver DEBUG statistics enabled
[ 2.169965]
[ 2.172347] port #0: is_sgmii=0, is_rgmii=1, phy_addr=0
[ 2.177616] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800
[ 2.185932]
[ 2.187426] o Port 0 is connected to Linux netdevice
[ 2.193325] o eth0, ifindex = 3, GbE port = 0
[ 2.201478] giga p=0: mtu=1500, mac=60:38:e0:b3:01:58 (hw config)
[ 2.207683]
[ 2.209258] port #2: is_sgmii=1, is_rgmii=0, phy_addr=1
[ 2.214549] o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048
[ 2.222869]
[ 2.224363] o Port 2 is connected to Linux netdevice
[ 2.230255] o eth1, ifindex = 4, GbE port = 2
[ 2.238409] giga p=2: mtu=1500, mac=ca:0a:37:0a:28:7d (random)
[ 2.244359]
[ 2.246120] (error) mv_switch_probe(5780) (rc=-22): read switch fdt file failed
[ 2.253475] mv_soho_switch: probe of switch.3 failed with error 1
[ 2.259605] o Loading Switch QuarterDeck driver
[ 2.268481] o Device ID : 0x352
[ 2.272334] o No. of Ports : 7
[ 2.275833] o CPU Port : 5
[ 2.281744] o Setting Switch Port #5 connected to GMAC port for 1000 Full with FC
[ 2.291797] o Setting Switch Port #6 connected to GMAC port for 1000 Full with FC
[ 2.310900] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.316337] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.329222] Switch driver init:
[ 2.332376] o preset mode = Transparent
[ 2.336573] o tag mode = No Tag
[ 2.346288] port #0 establish switch connection
[ 2.346288]
[ 2.352934] libphy: orion_mdio_bus: probed
[ 2.357183] mdio_bus f1072004.mdio-mi: cannot get PHY at address 0
[ 2.363565] mdio_bus f1072004.mdio-mi: cannot get PHY at address 1
[ 2.369950] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 2.377032] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 2.382850] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 2.388703] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 2.394696] PPP generic driver version 2.4.2
[ 2.399069] PPP BSD Compression module registered
[ 2.403817] PPP Deflate Compression module registered
[ 2.408888] NET: Registered protocol family 24
[ 2.413361] PPTP driver version 0.8.5
[ 2.417162] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.423724] ehci-pci: EHCI PCI platform driver
[ 2.428232] ehci-orion: EHCI orion driver
[ 2.432334] orion-ehci f1058000.usb: EHCI Host Controller
[ 2.437759] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 2.445411] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000
[ 2.470913] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 2.477070] hub 1-0:1.0: USB hub found
[ 2.480839] hub 1-0:1.0: 1 port detected
[ 2.484984] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.490326] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 2.497943] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
[ 2.503940] hub 2-0:1.0: USB hub found
[ 2.507706] hub 2-0:1.0: 1 port detected
[ 2.511697] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.517033] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 2.524745] hub 3-0:1.0: USB hub found
[ 2.528511] hub 3-0:1.0: 1 port detected
[ 2.532524] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.537860] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 2.545465] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
[ 2.551439] hub 4-0:1.0: USB hub found
[ 2.555205] hub 4-0:1.0: 1 port detected
[ 2.559185] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.564533] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 2.572246] hub 5-0:1.0: USB hub found
[ 2.576012] hub 5-0:1.0: 1 port detected
[ 3.081190] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[ 3.130979] i2c /dev entries driver
[ 3.145112] armada_thermal f10e4078.thermal: Overheat threshold between 92..107
[ 3.152620] md: raid0 personality registered for level 0
[ 3.157951] md: raid1 personality registered for level 1
[ 3.163288] md: raid6 personality registered for level 6
[ 3.168620] md: raid5 personality registered for level 5
[ 3.173974] md: raid4 personality registered for level 4
[ 3.179388] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 3.187896] dm_crypt using the OCF package.
[ 3.192102] Bluetooth: Virtual HCI driver ver 1.3
[ 3.196881] Bluetooth: HCI UART driver ver 2.2
[ 3.201396] usbcore: registered new interface driver bcm203x
[ 3.207118] usbcore: registered new interface driver bpa10x
[ 3.212758] usbcore: registered new interface driver bfusb
[ 3.218311] usbcore: registered new interface driver btusb
[ 3.223822] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 3.229564] cpuidle: using governor ladder
[ 3.233714] sdhci: Secure Digital Host Controller Interface driver
[ 3.239917] sdhci: Copyright(c) Pierre Ossman
[ 3.244371] mmc0: no vqmmc regulator found
[ 3.248482] mmc0: no vmmc regulator found
[ 3.290896] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 3.298471] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.316419] mmc0: new high speed SDIO card at address 0001
[ 3.340176] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2
[ 3.342519] Port 3: Link-up, Full-duplex, Speed-1000Mbps.
[ 3.354949] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1)
[ 3.364036] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xfffff
[ 3.373717] mvCesaInit: channels=2, session=640, queue=256
[ 3.387390] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode
[ 3.396367] cesadev_init(c085f284)
[ 3.400006] usbcore: registered new interface driver usbhid
[ 3.405655] usbhid: USB HID core driver
[ 3.409579] Loading Marvell spi device
[ 3.413636] NET: Registered protocol family 26
[ 3.418100] u32 classifier
[ 3.420817] Netfilter messages via NETLINK v0.30.
[ 3.425549] nfnl_acct: registering with nfnetlink.
[ 3.430377] nf_conntrack version 0.5.0 (7949 buckets, 31796 max)
[ 3.436480] ctnetlink v0.93: registering with nfnetlink.
[ 3.441824] nf_conntrack_rtsp v0.7 loading
[ 3.446005] ipip: IPv4 over IPv4 tunneling driver
[ 3.451001] gre: GRE over IPv4 demultiplexor driver
[ 3.455898] ip_gre: GRE over IPv4 tunneling driver
[ 3.461188] nf_nat_rtsp v0.7 loading
[ 3.464784] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.470186] arp_tables: (C) 2002 David S. Miller
[ 3.474827] TCP: cubic registered
[ 3.478176] NET: Registered protocol family 10
[ 3.483041] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.488544] sit: IPv6 over IPv4 tunneling driver
[ 3.493694] NET: Registered protocol family 17
[ 3.498185] Bridge firewalling registered
[ 3.502218] Ebtables v2.0 registered
[ 3.505868] Bluetooth: RFCOMM TTY layer initialized
[ 3.510771] Bluetooth: RFCOMM socket layer initialized
[ 3.515936] Bluetooth: RFCOMM ver 1.11
[ 3.519698] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.525034] Bluetooth: BNEP filters: protocol multicast
[ 3.530280] Bluetooth: BNEP socket layer initialized
[ 3.535266] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.541213] Bluetooth: HIDP socket layer initialized
[ 3.546206] l2tp_core: L2TP core driver, V2.0
[ 3.550580] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.555393] 8021q: 802.1Q VLAN Support v1.8
[ 3.559609] Key type dns_resolver registered
[ 3.563966] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 3.572048] regulator-dummy: disabling
[ 3.576267] input: gpio_keys.4 as /devices/soc.0/internal-regs.1/gpio_keys.4/input/input0
[ 3.584707] mvebu-rtc f10a3800.rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)
[ 3.592998] Waiting 1sec before mounting root device...
[ 4.600902] md: Waiting for all devices to be available before autodetect
[ 4.607717] md: If you don't use raid, use raid=noautodetect
[ 4.613657] md: Autodetecting RAID arrays.
[ 4.617768] md: Scanned 0 and added 0 devices.
[ 4.622235] md: autorun ...
[ 4.625036] md: ... autorun DONE.
[ 4.888644] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400000: 0x4c2e instead
[ 4.898172] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400004: 0x534b instead
[ 4.907695] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400008: 0x302e instead
[ 4.917215] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0240000c: 0x3030 instead
[ 4.926735] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400010: 0x5742 instead
[ 4.936254] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400014: 0x3233 instead
[ 4.945774] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400018: 0x4341 instead
[ 4.955293] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0240001c: 0x2020 instead
[ 4.964813] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400020: 0x3241 instead
[ 4.974333] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02400024: 0x4133 instead
[ 4.983852] jffs2: Further such events for this erase block will not be printed
[ 5.435014] VFS: Mounted root (jffs2 filesystem) readonly on device 31:6.
[ 5.441875] devtmpfs: mounted
[ 5.444942] Freeing unused kernel memory: 260K (c0842000 - c0883000)
*********************************************************************************
_ _ __ _ __ _____ __ __ _____
| | | || \ | | / // ____]\ \ / // ____]TM
| | | || \ | | / /| (___ \ V /| (____
| | | || |\ \| |\ \ \____ \ \ / \____ \
| |_____ | || | \ | \ \ ____) | | | ____) |
|_______||_||_| \__| \_\[____ / |_| [_____/
(c) 2014 Belkin International, Inc. and/or its affiliates. All rights reserved.
Booting rango (firmware version 1.0.8.198828)
*********************************************************************************
[utopia][init] System Initialization
[utopia][init] Creating /proc
[utopia][init] Creating /sys
[utopia][init] Creating /dev
[utopia][init] Creating /tmp
[utopia][init] Allocating 100M for /tmp
[utopia][init] Prepairing /dev/pts
[utopia][init] Setting /tmp and /var permissions
[utopia][init] Starting udev..
[ 6.449546] orion_wdt: Initial timeout 171 sec
Attempting mount of ubifs syscfg partition
UBI device number 0, total 680 LEBs (86343680 bytes, 82.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[utopia][init] Using persistent syscfg data from /var/config/syscfg
[utopia][init] Starting system logging
[utopia][init] Starting sysevent subsystem
net.netfilter.nf_conntrack_acct = 1
watchdog running
[utopia][init] Setting any unset system values to default
[utopia][init] no persistence config file (/var/config/pstcfg) found
mac_setup.sh, setting up MAC addresses for all interfaces based on 60:38:E0:B3:01:58
Updating NTP Servers if necessary
configuring switch port to router mode
checking for interactive script start up...
Updating BootCount Page[2]:1000 ... Done
attempting to sync sysinfo.cgi auth credentials
cpu temp monitor created
Thu Aug 8 18:37:00 UTC 2019
wdev0 no private ioctls.
wdev1 no private ioctls.
udhcpc (v1.15.2) started
Sending discover...
wan, sysevent received: phylink_wan_state
Sending discover...
Sending discover...
Lighttpd Model Base: WRT3200ACM
Generating Rainier lighttpd config
Build temporary www configuration directory:
$1$Z82zeWej$26y71a3HVh6AzsFdSx7T//
wifi, sysevent received: lan-started (Thu Aug 8 11:37:12 MST 2019)
wifi, service_start()
Registering Service WRT3200ACM._http._tcp.local port 80
Got a reply for WRT3200ACM._http._tcp.local.: Name now registered and active
starting /sbin/nmbd for bridge mode
Starting smbd ...
Not ready for JNAP. Sleeping for 15 seconds...
wifi, EEPROM powertables support
wifi, wdev0 regioncode: wdev0 getregioncode:16
wifi, wdev0 powertable: wdev0 gettxpower:0x00
wifi, wdev1 regioncode: wdev1 getregioncode:16
wifi, wdev1 powertable: wdev1 gettxpower:0x00
wifi, wifi_physical_start(wdev0)
wifi, wl1_state=down, do not start physical wdev0
wifi, wifi_virtual_start(wdev0)
wifi, wl1_state=down, do not start virtual wdev0ap0
wifi, wifi_physical_start(wdev1)
wifi, wl0_state=down, do not start physical wdev1
wifi, wifi_virtual_start(wdev1)
wifi, wl0_state=down, do not start virtual wdev1ap0
wifi, start_hostapd()
Bad argument `br0'
Error occurred at line: 25
Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information.
,Sending discover...
Sending discover...
Sending discover...
Restarting nfqrecv service...
Got a TERM signal, will terminate.
Warning! nfqrecv encountered errors when doing recv(): Interrupted system call
Sending discover...
Sending discover...
Sending discover...
Sending discover...