First try to support CPE210 v2 - will not boot

here goes the serial dump of factory firmware. wifi is working ok.. i only tryed it as AP and as Client. it is fine. il now put the sysupgrade and send serial dump also


U-Boot 1.1.4-g7613bad0-dirty (Jul 20 2017 - 17:08:57)

ap143-2.0 - Honey Bee 2.0

DRAM:  64 MB
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x50a1a100
is button pressed? 0
Autobooting in 1 seconds
## Booting image at 9f040000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.9.119 (robimarko@localhost.localdomain) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7822-6dac878c63) ) #0 Sat Aug 11 15:36:56 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=CPE210V3 mtdparts=spi0.0:128k(u-boot)ro,64k(partition-table)ro,64k(product-info)ro,7680k(firmware),192k(config)ro,64k(ART)ro console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59640K/65536K available (3362K kernel code, 165K rwdata, 812K rodata, 324K init, 213K bss, 5896K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:650.000MHz, DDR:390.771MHz, AHB:216.666MHz, Ref:25.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[    0.000010] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[    0.008274] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[    0.071121] pid_max: default: 32768 minimum: 301
[    0.076117] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.083092] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094030] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.104469] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.111629] NET: Registered protocol family 16
[    0.118172] MIPS: machine is TP-LINK CPE210 v3
[    0.376102] clocksource: Switched to clocksource MIPS
[    0.382782] NET: Registered protocol family 2
[    0.388332] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.395702] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.402495] TCP: Hash tables configured (established 1024 bind 1024)
[    0.409337] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.415514] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.422523] NET: Registered protocol family 1
[    0.433006] Crashlog allocated RAM at address 0x3f00000
[    0.440148] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.454182] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.460393] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.482723] io scheduler noop registered
[    0.486941] io scheduler deadline registered (default)
[    0.492718] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.499953] console [ttyS0] disabled
[    0.523899] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.533007] console [ttyS0] enabled
[    0.533007] console [ttyS0] enabled
[    0.540566] bootconsole [early0] disabled
[    0.540566] bootconsole [early0] disabled
[    0.553747] m25p80 spi0.0: found gd25q64, expected m25p80
[    0.561896] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[    0.566777] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.572890] Creating 6 MTD partitions on "spi0.0":
[    0.577870] 0x000000000000-0x000000020000 : "u-boot"
[    0.585540] 0x000000020000-0x000000030000 : "partition-table"
[    0.594098] 0x000000030000-0x000000040000 : "product-info"
[    0.602390] 0x000000040000-0x0000007c0000 : "firmware"
[    0.626673] 2 tplink-fw partitions found on MTD device firmware
[    0.632814] 0x000000040000-0x0000001a9647 : "kernel"
[    0.639693] 0x0000001b0000-0x0000007c0000 : "rootfs"
[    0.647004] mtd: device 5 (rootfs) set to be root filesystem
[    0.652912] 1 squashfs-split partitions found on MTD device rootfs
[    0.659392] 0x0000003e0000-0x0000007c0000 : "rootfs_data"
[    0.667798] 0x0000007c0000-0x0000007f0000 : "config"
[    0.675486] 0x0000007f0000-0x000000800000 : "ART"
[    0.684251] libphy: Fixed MDIO Bus: probed
[    0.716069] libphy: ag71xx_mdio: probed
[    1.349067] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.359360] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.367478] NET: Registered protocol family 10
[    1.376689] NET: Registered protocol family 17
[    1.381461] 8021q: 802.1Q VLAN Support v1.8
[    1.394201] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.404352] Freeing unused kernel memory: 324K
[    1.408991] This architecture does not have kernel memory protection.
[    2.096826] init: Console is alive
[    2.100649] init: - watchdog -
[    2.476114] random: fast init done
[    3.023957] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.077369] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.095649] init: - preinit -
[    3.746816] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    5.859845] eth0: link up (100Mbps/Full duplex)
[    5.864591] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.073590] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    7.091381] mount_root: switching to jffs2 overlay
[    7.129643] urandom-seed: Seeding with /etc/urandom.seed
[    7.310014] eth0: link down
[    7.327884] procd: - early -
[    7.330994] procd: - watchdog -
[    7.955011] procd: - watchdog -
[    7.958686] procd: - ubus -
[    8.067456] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.076003] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.083235] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.090862] procd: - init -
Please press Enter to activate this console.
[    8.469717] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.481862] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.501664] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[    8.510029] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[    8.520801] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.536730] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[    8.611047] xt_time: kernel timezone is -0000
[    8.692431] PPP generic driver version 2.4.2
[    8.700169] NET: Registered protocol family 24
[    8.777844] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[    8.866032] kmodloader: done loading kernel modules from /etc/modules.d/*
[    9.929901] urandom_read: 5 callbacks suppressed
[    9.929911] random: jshn: uninitialized urandom read (4 bytes read)
[    9.954776] random: ubusd: uninitialized urandom read (4 bytes read)
[   18.813581] br-lan: port 1(eth0) entered blocking state
[   18.819084] br-lan: port 1(eth0) entered disabled state
[   18.824975] device eth0 entered promiscuous mode
[   18.892918] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   20.899819] eth0: link up (100Mbps/Full duplex)
[   20.904592] br-lan: port 1(eth0) entered blocking state
[   20.910058] br-lan: port 1(eth0) entered forwarding state
[   20.966232] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


during and after firmware update... (sysupgrade)
it just loops after that form u-boot to kernel panic

Sending KILL to remaining processes ...
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...
Upgrade completed
Rebooting system...
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[  679.463135] reboot: Restarting system


U-Boot 1.1.4-g7613bad0-dirty (Jul 20 2017 - 17:08:57)

ap143-2.0 - Honey Bee 2.0

DRAM:  64 MB
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x50a1a100
is button pressed? 0
Autobooting in 1 seconds
## Booting image at 9f040000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.9.119 (robimarko@localhost.localdomain) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7822-6dac878c63) ) #0 Sat Aug 11 15:36:56 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=CPE210V3 mtdparts=spi0.0:128k(u-boot)ro,64k(partition-table)ro,64k(product-info)ro,7680k(firmware),192k(config)ro,64k(ART)ro console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59640K/65536K available (3362K kernel code, 165K rwdata, 812K rodata, 324K init, 213K bss, 5896K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:650.000MHz, DDR:390.771MHz, AHB:216.666MHz, Ref:25.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[    0.000010] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[    0.008274] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[    0.071121] pid_max: default: 32768 minimum: 301
[    0.076118] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.083092] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094035] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.104479] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.111638] NET: Registered protocol family 16
[    0.118178] MIPS: machine is TP-LINK CPE210 v3
[    0.376114] clocksource: Switched to clocksource MIPS
[    0.382787] NET: Registered protocol family 2
[    0.388342] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.395719] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.402512] TCP: Hash tables configured (established 1024 bind 1024)
[    0.409354] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.415530] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.422539] NET: Registered protocol family 1
[    0.433027] Crashlog allocated RAM at address 0x3f00000
[    0.440177] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.454212] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.460418] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.482748] io scheduler noop registered
[    0.486966] io scheduler deadline registered (default)
[    0.492744] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.499977] console [ttyS0] disabled
[    0.523923] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.533032] console [ttyS0] enabled
[    0.533032] console [ttyS0] enabled
[    0.540591] bootconsole [early0] disabled
[    0.540591] bootconsole [early0] disabled
[    0.553777] m25p80 spi0.0: found gd25q64, expected m25p80
[    0.561921] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[    0.566802] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.572915] Creating 6 MTD partitions on "spi0.0":
[    0.577895] 0x000000000000-0x000000020000 : "u-boot"
[    0.585565] 0x000000020000-0x000000030000 : "partition-table"
[    0.594123] 0x000000030000-0x000000040000 : "product-info"
[    0.602417] 0x000000040000-0x0000007c0000 : "firmware"
[    0.628506] 0x0000007c0000-0x0000007f0000 : "config"
[    0.636003] 0x0000007f0000-0x000000800000 : "ART"
[    0.644728] libphy: Fixed MDIO Bus: probed
[    0.676767] libphy: ag71xx_mdio: probed
[    1.309081] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.319355] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.327490] NET: Registered protocol family 10
[    1.336817] NET: Registered protocol family 17
[    1.341597] 8021q: 802.1Q VLAN Support v1.8
[    1.349177] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.356995] Please append a correct "root=" boot option; here are the available partitions:
[    1.365631] 1f00             128 mtdblock0 [    1.369782]  (driver?)
[    1.372226] 1f01              64 mtdblock1 [    1.376368]  (driver?)
[    1.378811] 1f02              64 mtdblock2 [    1.382941]  (driver?)
[    1.385377] 1f03            7680 mtdblock3 [    1.389520]  (driver?)
[    1.391963] 1f04             192 mtdblock4 [    1.396107]  (driver?)
[    1.398548] 1f05              64 mtdblock5 [    1.402680]  (driver?)
[    1.405123] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.414385] Rebooting in 1 seconds..



Well it looks like dynamic partition is not working

yea, i dont know what is going on. im just helping, wo any extensive programing knowlage :smile: tw should this thread be transfered to CPE210 V3 or something?

I will simply revert that patch and rebuild.
Provide you with fresh images today

no sweat. glad to be of service

Ok,fresh images
https://drive.google.com/drive/folders/1vds7-gIU-ybbnRmtuEkeqHs8kNe-BBXN?usp=sharing

This ones should work after sysupgrading

it is working fine...
no problems with wifi or anything

Great,so I will make a PR today to merge it.
Does sysupgrade image work?

yea. from original firmware i first upload FACTORY image after openwrt comes online at 192.168.1.1 i then upload SYSUPGRADE image. everything works wo any problems. fast and responsive.

Great,I opened a PR for it.

1 Like

This is getting better and better, great job, man...

Quick question though, is CPE220 v3 supported too? One of my relatives ordered one and got that version ._.

No,I am just working on CPE220 v2 since I have it but I have not seen a v3

The thing will come tomorrow, I can open it up, take pictures and maybe help you support it...

Sure, UART access would be awesome

For the support status of any device see the Table of Hardware.

In case you want to add support for CPE220 v3, please open a new topic for this device.

@robimarko made V3 work... im currently testing the image.. it is working fine...

CPE220 v3 stock firmware serial dump:
(U-Boot stuffs is gibberish, I'm using 115200 rate)

Linux version 2.6.31 (root@ubunt                                                                                                                     u) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Tue Jan 9 08:51:52 CST 2018
flash_size passed from bootloader = 8
CPU revision is: 00019374 (MIPS 24Kc)
ath_sys_frequency: cpu apb ddr apb cpu 650 ddr 392 ahb 216
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:04 rootfstype=squashfs init=/i                                                                                                                     nit mtdparts=ath-nor0:128k(u-boot),64k(pation-table),64k(product-info),1536k(ker                                                                                                                     nel),6144k(rootfs),192k(config),64k(ART) mem=64M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 61388k/65536k available (1832k kernel code, 4076k reserved, 473k data, 1                                                                                                                     12k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 432.12 BogoMIPS (lpj=864256)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
net_link: create socket ok.
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 120
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
7 cmdlinepart partitions found on MTD device ath-nor0
Creating 7 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000030000 : "pation-table"
0x000000030000-0x000000040000 : "product-info"
0x000000040000-0x0000001c0000 : "kernel"
0x0000001c0000-0x0000007c0000 : "rootfs"
0x0000007c0000-0x0000007f0000 : "config"
0x0000007f0000-0x000000800000 : "ART"
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
athwdt_timer_init: Starting WDT.
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 112k freed
init started:  BusyBox v1.01 (2018.01.09-00:52+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (1024 buckets, 30720 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
iptable_raw: version magic '2.6.31-gbb45668-dirty preempt mod_unload MIPS32_R2 3                                                                                                                     2BIT ' should be '2.6.31 preempt mod_unload MIPS32_R2 32BIT '
insmod: cannot insert `/lib/modules/2.6.31/kernel/iptable_raw.ko': Invalid modul                                                                                                                     e format (-1): Exec format error

Register vlan_manage hooks success.
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
WARN: TDB not supported!
WARN: TDB not supported!

 (none) mips #1 PREEMPT Tue Jan 9 08:51:52 CST 2018 (none)
(none) login: httpMudCreate: MUD 0x6613b0 was created
[info @ initModelParameters:205] init profile...

qca95xx_GMAC: Length per segment 1536
953x_GMAC: qca953x_gmac_attach
Link Int Enabled
qca953x_set_gmac_caps  CHECK DMA STATUS
mac:0 Registering S27....
qca95xx_GMAC: RX TASKLET - Pkts per Intr:18
qca95xx_GMAC: Mac address for unit 0:bfff0000
qca95xx_GMAC: ff:ff:ff:ff:ff:ff
qca95xx_GMAC: Max segments per packet :   1
qca95xx_GMAC: Max tx descriptor count :   128
qca95xx_GMAC: Max rx descriptor count :   128
qca95xx_GMAC: Mac capability flags    :   3581
953x_GMAC: qca953x_gmac_attach
Link Int Enabled
qca953x_set_gmac_caps  CHECK DMA STATUS
mac:1 Registering S27....
qca95xx_GMAC: RX TASKLET - Pkts per Intr:18
qca95xx_GMAC: Mac address for unit 1:bfff0006
qca95xx_GMAC: ff:ff:ff:ff:ff:ff
qca95xx_GMAC: Max segments per packet :   1
qca95xx_GMAC: Max tx descriptor count :   128
qca95xx_GMAC: Max rx descriptor count :   128
qca95xx_GMAC: Mac capability flags    :   3D81
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
athr_gmac_ring_alloc Allocated 2048 at 0x83a85800
athr_gmac_ring_alloc Allocated 2048 at 0x83a85000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_alloc Allocated 2048 at 0x83a99800
athr_gmac_ring_alloc Allocated 2048 at 0x83a99000
HONEYBEE ----> S27 PHY MDIO
ATHRS27: resetting s27
ATHRS27: s27 reset done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...

Disable VlanManage, data.enable(0), data.vid(0)
rmmod: br_dhcp_filter.ko: No such file or directory
[dhcpcKill:643]error: dhcpc status:3
command not supported

Board:
IMG_20180815_090526

Flash chip:
IMG_20180815_093645

Well it looks like V2.
Can you check what SoC is in it?

Will do later tonight...