I am using putty on windows 10. Serial adapter pins are double checked. I cannot stop it from booting.
U-Boot 1.1.4--LSDK-10.2-00082-4 (Jul 3 2020 - 14:45:22)
board953x - Honey Bee 2.0DRAM:
sri
Honey Bee 2.0
ath_ddr_initial_config(195): (16bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x6, 0x37)
Tap values = (0x1e, 0x1e, 0x1e, 0x1e)
devInfo: EAP110-Outdoor(TP-LINK|UN|N300-2):3.0
64 MB
Flash Manuf Id 0x1c, DeviceId0 0x70, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash: 8 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Setting 0x181162c0 to 0x50a1a100
Hit Ctrl+B to stop autoboot: 0
Loading .text @ 0x80248790 (4784 bytes)
Loading .rodata.str1.4 @ 0x80249a40 (212 bytes)
Loading .data @ 0x80249b20 (780290 bytes)
Clearing .bss @ 0x80308330 (4202512 bytes)
## Starting application at 0x80248790 ...
Booting QCA953x
[ 0.000000] Linux version 2.6.31 (jenkins@sohoiapbuild) (gcc version 4.3.3 (G CC) ) #1 PREEMPT Wed Feb 16 15:48:28 CST 2022
[ 0.000000] flash_size passed from bootloader = -1
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] ath_sys_frequency: cpu apb ddr apb cpu 650 ddr 391 ahb 216
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:04 rootfstype=s quashfs init=/init mtdparts=ath-nor0:128k(u-boot),64k(pation-table),64k(product- info),1536k(kernel),6144k(rootfs),192k(config),64k(ART) mem=64M
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 62436k/65536k available (1755k kernel code, 3028k reserve d, 461k data, 112k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 432.12 BogoMIPS (lpj=864256)
[ 0.084000] Mount-cache hash table entries: 512
[ 0.084000] NET: Registered protocol family 16
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] NET: Registered protocol family 2
[ 0.096000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.096000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.096000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.096000] TCP reno registered
[ 0.096000] NET: Registered protocol family 1
[ 0.096000] ATH GPIOC major 0
[ 0.096000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.096000] msgmni has been set to 122
[ 0.096000] alg: No test for lzma (lzma-generic)
[ 0.096000] alg: No test for stdrng (krng)
[ 0.096000] io scheduler noop registered
[ 0.096000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.100000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.100000] console [ttyS0] enabled
[ 0.364000] PPP generic driver version 2.4.2
[ 0.372000] NET: Registered protocol family 24
[ 0.376000] 7 cmdlinepart partitions found on MTD device ath-nor0
[ 0.384000] Creating 7 MTD partitions on "ath-nor0":
[ 0.388000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.392000] 0x000000020000-0x000000030000 : "pation-table"
[ 0.400000] 0x000000030000-0x000000040000 : "product-info"
[ 0.408000] 0x000000040000-0x0000001c0000 : "kernel"
[ 0.412000] 0x0000001c0000-0x0000007c0000 : "rootfs"
[ 0.420000] 0x0000007c0000-0x0000007f0000 : "config"
[ 0.424000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.432000] TCP cubic registered
[ 0.436000] NET: Registered protocol family 17
[ 0.440000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.448000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.452000] athwdt_init: Registering WDT success
[ 0.460000] athwdt_timer_init: Starting WDT.
[ 0.472000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.480000] Freeing unused kernel memory: 112k freed
[ 0.504000] __tty_open: Opening ttyS0 and default set O_NONBLOCK...
init started: BusyBox v1.20.2 (2022-02-16 15:54:50 CST)
starting pid 97, tty '': '/etc/rc.d/rcS >/dev/c[ 1.516000] __tty_open: Openin g ttyS0 and default set O_NONBLOCK...
onsole 2>&1'
[NM_Debug](main) 01042: getopt_long: c=C
[NM_Debug](main) 01042: getopt_long: c=▒
[NM_Debug](main) 01125: excute the command: start=====>
[NM_Debug](nm_lock_init) 00149: create semaphore...
[NM_Debug](nm_lib_getProductInfoFromNvram) 00928: productinfo from NVRAM is (EAP 110-Outdoor(TP-LINK|UN|N300-2):3.0
key=BgIAAAAkAABSU0ExAAQAAAEAAQDZtUNzD6KsxO4Tfx/Sp8S7w8TwPWwoppXy77wSPNs5WoV+Wr4k h09nu70vHVmSPji5KFUG+hmRjapsJsIJj+M0Zmd4EycKY8r0Ea3D4XO/uvloX4VHVPsDZkm8Krian5iN y6BgApVlebx0zQxto0GkgvPBq1nhoZxJNapLghGO7w==
rsaKey=BgIAAACkAABSU0ExAAQAAAEAAQC33Ux/UTRSBo17Xm/eESv+2ZRoomAXfr1LIk2PbKmBLSldP pfeCH/m4rhY4wLiXqAke7DiRZkK6xjdahNG3uzffdaRZaxTjzY/UqsWJaqlP08Q+p1tF8YfqqeEn3WqC G6nVxmCvoIH8t3xTZQ8RgDNWdO7v1IBARwN/8ffyjr4uQ==
HWID=9CBC53BF2C349A420BA617EBE88F9889)
This Board use 2.6.31
[ 2.564000] xt_time: kernel timezone is -0000
[ 2.804000] nf_conntrack version 0.5.0 (1024 buckets, 30720 max)
[ 3.388000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.644000] Ebtables v2.0 registered
insmod: can't insert '/lib/modules/2.6.31/kernel/ts_kmp.ko': No such file or directory
insmod: can't insert '/lib/modules/2.6.31/kernel/br_filter.ko': No such file or directory
[ 3.788000] ---portal module open ok
[ 3.876000] Register vlan_manage hooks success.
insmod: can't insert '/lib/modules/2.6.31/kernel/statistics.ko': No such file or directory
[ 3.996000] [Debug gpio_parse_conf:271] Open File /etc/EAP110-Outdoor_3.0/gpio.conf SUCCESS!!
[ 4.028000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 14, readCount 256
[ 4.036000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 44, readCount 256
[ 4.040000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 6 , readCount 256
[ 4.048000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 7 , readCount 256
[ 4.056000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 2 , readCount 256
[ 4.064000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 7 , readCount 256
[ 4.072000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 44, readCount 256
[ 4.080000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 6 , readCount 256
[ 4.088000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 7 , readCount 256
[ 4.096000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 2 , readCount 256
[ 4.104000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 7 , readCount 256
[ 4.112000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 44, readCount 256
[ 4.120000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 7 , readCount 250
[ 4.128000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 6 , readCount 243
[ 4.136000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 6 , readCount 237
[ 4.144000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 6 , readCount 231
[ 4.152000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 2 , readCount 225
[ 4.160000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 51, readCount 223
[ 4.168000] [Debug gpio_parse_conf:360] Ignore line (0), skipLen 44, readCount 172
[ 4.176000] [Debug gpio_parse_conf:388] GPIO Parse OK: led_green led(1) low (0) low (0) 12
[ 4.184000] [Debug gpio_parse_conf:388] GPIO Parse OK: led_yellow led(1) low (0) high(1) 11
[ 4.192000] [Debug gpio_parse_conf:388] GPIO Parse OK: btn_reset btn(2) low (0) high(1) 17
[ 4.200000] [Debug btn_netlink_init:179] btn: create netlink socket SUCCESS.
[ 4.208000] [Debug wdt_module_init:249] Create watchdog proc dir SUCCESS.
[ 4.216000] [Debug led_entry_handler:783] Create led_green proc dir SUCCESS.
[ 4.224000] [Debug led_entry_handler:783] Create led_yellow proc dir SUCCESS.
[ 4.232000] [Debug btn_entry_handler:913] Init button: btn_reset 2 17 0 success.
[ 4.316000] rate_limit: module license 'BSD' taints kernel.
[ 4.324000] Disabling lock debugging due to kernel taint
[ 4.528000] [Debug btn_netlink_receive:72] BTN netlink with user space daemon 210 SUCCESS.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode repeat, delayon 200, delayoff 200, blinkCount 0.
[Debug checkLedParamValid:345] Param: mode repeat, delayon 200, delayoff 200, blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode repeat, delayon 500, delayoff 500, blinkCount 0.
[Debug checkLedParamValid:345] Param: mode repeat, delayon 500, delayoff 500, blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode repeat, delayon 200, delayoff 200, blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode on , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode blink, delayon 500, delayoff 500, blinkCount 4.
[Debug checkLedParamValid:345] Param: mode disable, delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode enable, delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode blink, delayon 200, delayoff 200, blinkCount 3000.
[Debug checkLedParamValid:345] Param: mode stop , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0.
[Debug checkLedParamValid:345] Param: mode repeat, delayon 4200, delayoff 800, blinkCount 0.
[Debug checkLedParamValid:345] Param: mode stop , delayon 0 , delayoff 0 , blinkCount 0.
LED_RESET
{ led_green off 1 0 0 0 }
{ led_yellow off 1 0 0 0 }
{ led_yellow repeat 1 200 200 0 }
{ led_green repeat 1 200 200 0 }
LED_UPDATE_START
{ led_green off 1 0 0 0 }
{ led_yellow off 1 0 0 0 }
{ led_yellow repeat 1 500 500 0 }
{ led_green repeat 1 500 500 0 }
LED_UPDATE_FINISH
{ led_yellow off 1 0 0 0 }
{ led_green off 1 0 0 0 }
LED_DUT_NO_CALDATA
{ led_green off 0 0 0 0 }
{ led_yellow repeat 4 200 200 0 }
LED_SYS_INIT_PROCESS
{ led_yellow off 0 0 0 0 }
{ led_green on 0 0 0 0 }
LED_SYS_INIT_OK
{ led_yellow off 0 0 0 0 }
{ led_green blink[ 4.800000] __tty_open: Opening ttyS0 and default set O_NONBLOCK...
0 500 500 4 }
LED_DISABLE_ALL
{ led_green disable 2 0 0 0 }
LED_ENABLE_ALL
{ led_green enable 0 0 0 0 }
LED_LOCATE
{ led_green blink 19 200 200 3000 }
LED_LOCATE_STOP
{ led_green stop 1 0 0 0 }
LED_ISOLATED_START
{ led_yellow off 0 0 0 0 }
{ led_green repeat 2 4200 800 0 }
LED_ISOLATED_FINISH
{ led_green stop 0 0 0 0 }
mesh is not supported
ap_watchdog is not supported.
[NM_Debug](main) 01042: getopt_long: c=r
[NM_Debug](main) 01042: getopt_long: c=p
[NM_Debug](main) 01042: getopt_long: c=▒
[NM_Debug](main) 01125: excute the command: start=====>
[NM_Debug](nm_lib_readPtnUsedSize) 00553: partition name not found(name:region), read from special ptn.
[NM_Debug](nvrammanager_readPtnFromNvram) 00834: Ptn used size buflen = 8
Japan disaster mode is not enabled for region not match
starting pid 232, tty '': '/sbin/getty ttyS0 115200'
Into util_dbg_setMod, pModName(all), enable(1)
(none) mips #1 PREEMPT Wed Feb 16 15:48:28 CST 2022 (none)
(none) login: [Debug ledListenEventHandler:148] Accept a new client.
[Debug ledClientEventHandler:110] GPIOD received led rule: LED_SYS_INIT_PROCESS.
[ 6.656000] [Debug led_proc_write:651] Write led_yellow.
[ 6.664000] [Debug led_common_write_proc:490] Execute LED action: { 1 0 0 0 0 }
[ 6.700000] [Debug led_proc_write:651] Write led_green.
[ 6.704000] [Debug led_common_write_proc:490] Execute LED action: { 2 0 0 0 0 }
==============radio config============
radioType: 0x1
EIRP: 1
0. radioID:0
band:2
mimo:2
mimogain:3
anttgain:1
mode:7
blockAcsBand:0
chanlimit:0
dfsImproveSupp:0
thermalSupp:0
level[0] 0 0 0
level[1] 0 0 0
level[2] 0 0 0
level[3] 0 0 0
QCA HAL BB reg:
CCA: 0
00000000
AGC: 0
00000000
00000000
PSD 0
00000000
00000000
00000000
noAutoWradarSupp:0
==============radio config============
<debug>_radio_region_init(): 234 @ read next region flag, parse finish
<debug>_radio_region_init(): 263 @ region:276, parse channel num:13
GBK essid(TP-Link_2.4GHz_A9B2A8)
UTF8 essid(TP-Link_2.4GHz_A9B2A8)
[ 9.068000] [Debug led_proc_write:651] Write led_green.
[Debug ledClien[ 9.076000] [Debug led_common_write_proc:490] Execute LED action: tEventHandler:11 { 5 0 0 0 0 }
0] GPIOD receive[ 9.088000] [NOTICE led_common_write_proc:527] pledconf->backup.mode 0 1
d led rule: LED_ENABLE_ALL.
[ 9.196000] qca953x_GMAC: Length per segment 1536
[ 9.200000] 953x_GMAC: qca953x_gmac_attach
[ 9.208000] Link Int Enabled
[ 9.208000] qca953x_set_gmac_caps CHECK DMA STATUS
[ 9.216000] mac:0 Registering S27....
[ 9.220000] qca953x_GMAC: RX TASKLET - Pkts per Intr:18
[ 9.224000] qca953x_GMAC: RX TASKLET - Timer Freq r:376
[ 9.228000] qca953x_GMAC: RX TASKLET - Rx Desc :128
[ 9.232000] qca953x_GMAC: Mac address for unit 0:bfff0000
[ 9.240000] qca953x_GMAC: ff:ff:ff:ff:ff:ff
[ 9.244000] qca953x_GMAC: Max segments per packet : 1
[ 9.252000] qca953x_GMAC: Max tx descriptor count : 128
[ 9.256000] qca953x_GMAC: Max rx descriptor count : 128
[ 9.260000] qca953x_GMAC: Mac capability flags : 3581
[ 9.268000] 953x_GMAC: qca953x_gmac_attach
[ 9.272000] Link Int Enabled
[ 9.276000] qca953x_set_gmac_caps CHECK DMA STATUS
[ 9.280000] mac:1 Registering S27....
[ 9.284000] qca953x_GMAC: RX TASKLET - Pkts per Intr:18
[ 9.288000] qca953x_GMAC: RX TASKLET - Timer Freq r:376
[ 9.296000] qca953x_GMAC: RX TASKLET - Rx Desc :128
[ 9.300000] qca953x_GMAC: Mac address for unit 1:bfff0006
[ 9.304000] qca953x_GMAC: ff:ff:ff:ff:ff:ff
[ 9.312000] qca953x_GMAC: Max segments per packet : 1
[ 9.316000] qca953x_GMAC: Max tx descriptor count : 128
[ 9.320000] qca953x_GMAC: Max rx descriptor count : 128
[ 9.328000] qca953x_GMAC: Mac capability flags : 3D81
[ 10.292000] athr_gmac_ring_alloc Allocated 2048 at 0x83ac5000
[ 10.300000] athr_gmac_ring_alloc Allocated 2048 at 0x83ba7800
[ 10.604000] HONEYBEE ----> S27 PHY MDIO 20180115
[ 10.612000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 10.616000] Setting PHY...
[ 15.160000] athr_gmac_ring_alloc Allocated 2048 at 0x82c13000
[ 15.168000] athr_gmac_ring_alloc Allocated 2048 at 0x83b9a800
[ 15.472000] HONEYBEE ----> S27 PHY MDIO 20180115
[ 15.480000] ATHRS27: resetting s27
[ 15.584000] ATHRS27: s27 reset done
[ 15.596000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 15.604000] Setting PHY...
[ 18.188000]
[ 18.188000] Disable VlanManage, data.enable(0), data.vid(1)
[ 18.196000] CJ++ for mspi_read_id get id=0x1c
[ 18.200000] UID:
[ 18.204000] 1c 2d 31 30 4d 31 67 17 01 21 2c 3d uid = 0x1c 0x2d 0x31 0x30 0x4d 0x31 0x67 0x17 0x1 0x21 0x2c 0x3d 0x0 0x0 0x0 0x0
[NM_Debug](readFlashPublicKey) 00175: rsaKey=: BgIAAACkAABSU0ExAAQAAAEAAQC33Ux/UTRSBo17Xm/eESv+2ZRoomAXfr1LIk2PbKmBLSldPpfeCH/m4rhY4wLiXqAke7DiRZkK6xjdahNG3uzffdaRZaxTjzY/UqsWJaqlP08Q+p1tF8YfqqeEn3WqCG6nVxmCvoIH8t3xTZQ8RgDNWdO7v1IBARwN/8ffyjr4uQ==!
Rsa verify success
[ 18.368000] manage vlan set port: ssh (22), http (80), https (443)
[ 18.372000]
[ 18.372000] manage vlan set port: ssh (22), http (80), https (443)
[ 18.384000] CJ++ for mspi_read_id get id=0x1c
[ 18.388000] UID:
[ 18.392000] 1c 2d 31 30 4d 31 67 17 01 21 2c 3d uid = 0x1c 0x2d 0x31 0x30 0x4d 0x31 0x67 0x17 0x1 0x21 0x2c 0x3d 0x0 0x0 0x0 0x0
[NM_Debug](readFlashPublicKey) 00175: rsaKey=: BgIAAACkAABSU0ExAAQAAAEAAQC33Ux/UTRSBo17Xm/eESv+2ZRoomAXfr1LIk2PbKmBLSldPpfeCH/m4rhY4wLiXqAke7DiRZkK6xjdahNG3uzffdaRZaxTjzY/UqsWJaqlP08Q+p1tF8YfqqeEn3WqCG6nVxmCvoIH8t3xTZQ8RgDNWdO7v1IBARwN/8ffyjr4uQ==!
Rsa verify success
[ 20.844000] __ath_attach: Set global_scn[0]
[ 20.852000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
[ 20.860000] ACBKMinfree = 48
[ 20.864000] ACBEMinfree = 32
[ 20.868000] ACVIMinfree = 16
[ 20.868000] ACVOMinfree = 0
[ 20.872000] CABMinfree = 48
[ 20.876000] UAPSDMinfree = 0
[ 20.880000] ATH_TXBUF=512
[ 20.892000] SPECTRAL : get_capability not registered
[ 20.900000] HAL_CAP_PHYDIAG : Capable
[ 20.904000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231)
[ 20.912000] SPECTRAL : get_capability not registered
[ 20.916000] HAL_CAP_RADAR : Capable
[ 20.920000] SPECTRAL : Need to fix the capablity check for SPECTRAL
[ 20.920000] (spectral_attach : 236)
[ 20.932000] SPECTRAL : get_capability not registered
[ 20.936000] HAL_CAP_SPECTRAL_SCAN : Capable
[ 20.940000] SPECTRAL : get_tsf64 not registered
[ 20.944000] spectral_init_netlink 52 NULL SKB
[ 20.948000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT
[ 20.956000] SPECTRAL :----- module attached
[ 20.964000] ath_get_caps[6360] rx chainmask mismatch actual 3 sc_chainmak 0
[ 20.968000] ath_get_caps[6335] tx chainmask mismatch actual 3 sc_chainmak 0
[ 20.984000] ath_attach_dfs[12861] dfsdomain 1
[ 21.000000] SPECTRAL : module already attached
[ 21.012000] ATH_RESERVED_TXBUF = 1000
[ 21.016000] ath_tx_paprd_init sc 82df8000 PAPRD disabled in HAL
[ 21.176000] ath_attach_dfs[12861] dfsdomain 1
Interface doesn't accept private ioctl...
HALDbg (8BE0): Operation not permitted
[ 21.328000] wlan_vap_create : enter. devhandle=0x82ea02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 21.340000] wlan_vap_create : exit. devhandle=0x82ea02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 21.348000] VAP device ath0 created
ath0
[ 21.364000] ath_attach_dfs[12861] dfsdomain 2
[ 21.632000]
[ 21.632000] DES SSID SET=TP-Link_2.4GHz_A9B2A8
[ 21.688000] Set beacon rate: 1000
[ 21.700000] Set bcast rate: 1000
[ 21.712000] Set mcast rate: 1000
[ 21.728000] Set mgmt rate: 1000
[ 21.740000] Set data minrate: 0
[ 21.752000] Set sta minrate: 1000
[ 21.776000] Set disable CCK rate: 0
[ 21.980000]
[ 21.980000] manage vlan set ssid vlan: idx (0), intfName (ath0), vlan (0)
[ 22.008000] [Debug led_proc_write:651] Write led_yellow.
[Debug ledClien[ 22.012000] [Debug led_common_write_proc:490] Execute LED action: tEventHandler:11 { 1 0 0 0 0 }
0] GPIOD received led rule: LED_SYS_INIT_OK.
[ 22.028000] [Debug led_proc_write:651] Write led_green.
[ 22.036000] [Debug led_common_write_proc:490] Execute LED action: { 3 0 500 500 4 }
iptables: Bad rule (does a[ 24.036000] CJ++ for mspi_read_id get id=0x1c
matching rule e[ 24.044000] UID:
xist in that cha[ 24.048000] 1c in?).
2d 31 30 4d 31 67 17 01 21 2c 3d uid = 0x1c 0x2d 0x31 0x30 0x4d 0x31 0x67 0x17 0x1 0x21 0x2c 0x3d 0x0 0x0 0x0 0x0
[NM_Debug](readFlashPublicKey) 00175: rsaKey=: BgIAAACkAABSU0ExAAQAAAEAAQC33Ux/UTRSBo17Xm/eESv+2ZRoomAXfr1LIk2PbKmBLSldPpfeCH/m4rhY4wLiXqAke7DiRZkK6xjdahNG3uzffdaRZaxTjzY/UqsWJaqlP08Q+p1tF8YfqqeEn3WqCG6nVxmCvoIH8t3xTZQ8RgDNWdO7v1IBARwN/8ffyjr4uQ==!
Rsa verify success
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
now ok to start tddp---------------------
[TDDP_DEBUG]<debug>[main:1290] tddp init---
uclite init ok, now startup eap-cs ---------------------
httpMudCreate: MUD 0x4caf20 was created
[utilities_debug: httpSystemFirmwareInit:271]register rpm
httpServerCreate------------------
httpsServerCreate: https try to add port 443
<httpd>[debug]initModules(): 137 -> unix_sock_initSrv success, and then register / alias
<httpd>[debug]initModules(): 145 -> register / alias success
<httpd>[debug]http_inetd_addListenSocket(): 683 -> listen add port(22443), ssl(1)
<httpd>[debug]http_inetd_addListenSocket(): 683 -> listen add port(33443), ssl(1)
<httpd>[debug]http_inetd_addListenSocket(): 683 -> listen add port(44443), ssl(1)
<httpd>[debug]http_inetd_addListenSocket(): 683 -> listen add port(33080), ssl(0)
httpServerCreate: http try to add port 80
httpServerCreate: http try to add port 22080
route: SIOCDELRT: No such process
[UNIX_SOCK][unix_sock_connSrv:301]connect to file(/var/run/srv/22) failed after retry(0), errno(2):No such file or directory
Into util_dbg_setMod, pModName(all), enable(1)
I spam Ctrl-Brake but nothing.. Tried with two different serial to usb adapters.
