Just flashed 22.03.2 on a TP-Link Archer C7 v4
Kernel log below.
- [ 0.409954] - are the bad cell count messages something to be concerned about?
- [ 0.484742] - are the partitions not ending on erase/write blocks something to be concerned about?
- [ 1.972984] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. - AFAIK, I'm not doing any filtering on the bridge. Is this cruft?
- [ 81.975011] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware - is this a problem?
L.
[ 0.000000] Linux version 5.10.146 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19803-9a599fee93) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Fri Oct 14 22:44:41 2022
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link Archer C7 v4
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 121084K/131072K available (5850K kernel code, 611K rwdata, 744K rodata, 1232K init, 209K bss, 9988K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008273] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.074802] pid_max: default: 32768 minimum: 301
[ 0.079798] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.087513] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097630] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.108342] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.118753] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.126018] pinctrl core: initialized pinctrl subsystem
[ 0.135467] NET: Registered protocol family 16
[ 0.140868] thermal_sys: Registered thermal governor 'step_wise'
[ 0.192089] clocksource: Switched to clocksource MIPS
[ 0.204888] NET: Registered protocol family 2
[ 0.209686] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.218058] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.226982] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.235083] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.242532] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.249353] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.256292] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.263938] NET: Registered protocol family 1
[ 0.268556] PCI: CLS 0 bytes, default 32
[ 0.278457] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.288769] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.294977] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.306994] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.317355] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.324034] gpio-export gpio-export: 2 gpio(s) exported
[ 0.330327] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.339159] printk: console [ttyS0] disabled
[ 0.343778] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.352890] printk: console [ttyS0] enabled
[ 0.361935] printk: bootconsole [early0] disabled
[ 0.387559] led_gpio@0 enforce active low on chipselect handle
[ 0.398295] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.403355] 5 fixed-partitions partitions found on MTD device spi0.0
[ 0.409954] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.416840] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.424115] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.430965] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.438418] Creating 5 MTD partitions on "spi0.0":
[ 0.443435] 0x000000000000-0x000000020000 : "factory-uboot"
[ 0.454380] 0x000000020000-0x000000040000 : "u-boot"
[ 0.460447] 0x000000040000-0x000000f00000 : "firmware"
[ 0.468285] 2 uimage-fw partitions found on MTD device firmware
[ 0.474462] Creating 2 MTD partitions on "firmware":
[ 0.479598] 0x000000000000-0x000000223e5c : "kernel"
[ 0.484742] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[ 0.494951] 0x000000223e5c-0x000000ec0000 : "rootfs"
[ 0.500093] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 0.510473] mtd: device 4 (rootfs) set to be root filesystem
[ 0.517257] 1 squashfs-split partitions found on MTD device rootfs
[ 0.523701] 0x000000610000-0x000000ec0000 : "rootfs_data"
[ 0.530182] 0x000000f00000-0x000000ff0000 : "info"
[ 0.537617] 0x000000ff0000-0x000001000000 : "art"
[ 1.266152] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.923652] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.934921] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.941754] i2c /dev entries driver
[ 1.955169] NET: Registered protocol family 10
[ 1.964370] Segment Routing with IPv6
[ 1.968257] NET: Registered protocol family 17
[ 1.972984] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.986388] 8021q: 802.1Q VLAN Support v1.8
[ 1.991538] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[ 1.997917] MEM 0x0000000012000000..0x0000000013ffffff
[ 2.003328] IO 0x0000000000000000..0x0000000000000000
[ 2.008897] PCI host bridge to bus 0000:00
[ 2.013174] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 2.020274] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.026042] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.033063] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.041288] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 2.047537] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 2.054604] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.061595] pci 0000:00:00.0: supports D1 D2
[ 2.067026] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.073915] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 2.081479] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 2.101342] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.115425] Freeing unused kernel memory: 1232K
[ 2.120104] This architecture does not have kernel memory protection.
[ 2.126791] Run /sbin/init as init process
[ 2.131015] with arguments:
[ 2.131019] /sbin/init
[ 2.131023] with environment:
[ 2.131027] HOME=/
[ 2.131030] TERM=linux
[ 2.857206] init: Console is alive
[ 2.861152] init: - watchdog -
[ 4.345939] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.401116] usbcore: registered new interface driver usbfs
[ 4.406891] usbcore: registered new interface driver hub
[ 4.412505] usbcore: registered new device driver usb
[ 4.424870] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.434641] ehci-fsl: Freescale EHCI Host controller driver
[ 4.442544] ehci-platform: EHCI generic platform driver
[ 4.448271] ehci-platform 1b000000.usb: EHCI Host Controller
[ 4.454203] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 4.462423] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 4.492115] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 4.499378] hub 1-0:1.0: USB hub found
[ 4.504024] hub 1-0:1.0: 1 port detected
[ 4.508865] ehci-platform 1b400000.usb: EHCI Host Controller
[ 4.514797] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[ 4.523053] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
[ 4.552115] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[ 4.559311] hub 2-0:1.0: USB hub found
[ 4.564007] hub 2-0:1.0: 1 port detected
[ 4.571346] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.589320] init: - preinit -
[ 6.527661] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.009170] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.256946] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.543617] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.724283] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.902012] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 1 is up
[ 8.916608] eth0: link up (1000Mbps/Full duplex)
[ 8.921425] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.943872] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 8.972547] random: procd: uninitialized urandom read (4 bytes read)
[ 13.335800] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 13.343311] jffs2_build_filesystem(): unlocking the mtd device...
[ 13.343315] done.
[ 13.351668] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 40.229644] done.
[ 40.239428] jffs2: notice: (556) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 40.256926] mount_root: overlay filesystem has not been fully initialized yet
[ 40.271631] mount_root: switching to jffs2 overlay
[ 40.279637] overlayfs: upper fs does not support tmpfile.
[ 40.925496] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 41.050924] eth0: link down
[ 41.073749] procd: - early -
[ 41.077059] procd: - watchdog -
[ 41.699061] procd: - watchdog -
[ 41.703012] procd: - ubus -
[ 41.806882] random: ubusd: uninitialized urandom read (4 bytes read)
[ 41.816079] random: ubusd: uninitialized urandom read (4 bytes read)
[ 41.823248] random: ubusd: uninitialized urandom read (4 bytes read)
[ 41.837819] procd: - init -
[ 43.096805] random: jshn: uninitialized urandom read (4 bytes read)
[ 43.198040] kmodloader: loading kernel modules from /etc/modules.d/*
[ 43.596985] urngd: v1.0.2 started.
[ 43.722804] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[ 43.730631] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[ 43.797374] random: crng init done
[ 43.800905] random: 24 urandom warning(s) missed due to ratelimiting
[ 44.128612] PPP generic driver version 2.4.2
[ 44.136525] NET: Registered protocol family 24
[ 44.175448] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 44.185247] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 44.194022] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 48.027195] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 48.036782] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 48.048730] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[ 48.163983] ath10k_pci 0000:00:00.0: Loading BDF type 0
[ 49.052758] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 50.055890] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 50.072641] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 50.079075] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 50.087375] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 50.137208] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 50.150062] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 50.285771] ath: EEPROM regdomain: 0x0
[ 50.285783] ath: EEPROM indicates default country code should be used
[ 50.285787] ath: doing EEPROM country->regdmn map search
[ 50.285800] ath: country maps to regdmn code: 0x3a
[ 50.285806] ath: Country alpha2 being used: US
[ 50.285810] ath: Regpair used: 0x3a
[ 50.388925] ath: EEPROM regdomain: 0x0
[ 50.388938] ath: EEPROM indicates default country code should be used
[ 50.388942] ath: doing EEPROM country->regdmn map search
[ 50.388955] ath: country maps to regdmn code: 0x3a
[ 50.388962] ath: Country alpha2 being used: US
[ 50.388966] ath: Regpair used: 0x3a
[ 50.400518] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 50.402467] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[ 50.442664] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 72.619730] eth0: link up (1000Mbps/Full duplex)
[ 72.642643] br-lan: port 1(eth0.1) entered blocking state
[ 72.648298] br-lan: port 1(eth0.1) entered disabled state
[ 72.654202] device eth0.1 entered promiscuous mode
[ 72.659156] device eth0 entered promiscuous mode
[ 72.671120] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 72.748543] br-lan: port 1(eth0.1) entered blocking state
[ 72.754180] br-lan: port 1(eth0.1) entered forwarding state
[ 73.692180] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 76.628428] ath: EEPROM regdomain: 0x<redacted>
[ 76.632628] ath: EEPROM indicates we should expect a country code
[ 76.638918] ath: doing EEPROM country->regdmn map search
[ 76.644423] ath: country maps to regdmn code: 0x<redacted>
[ 76.649365] ath: Country alpha2 being used: <redacted>
[ 76.653962] ath: Regpair used: 0x<redacted>
[ 76.657562] ath: regdomain 0x<redacted> dynamically updated by user
[ 76.663584] ath: EEPROM regdomain: 0x<redacted>
[ 76.667721] ath: EEPROM indicates we should expect a country code
[ 76.674022] ath: doing EEPROM country->regdmn map search
[ 76.679505] ath: country maps to regdmn code: 0x<redacted>
[ 76.684461] ath: Country alpha2 being used: <redacted>
[ 76.689045] ath: Regpair used: 0x<redacted>
[ 76.692648] ath: regdomain 0x<redacted> dynamically updated by user
[ 78.490306] br-lan: port 2(wlan1) entered blocking state
[ 78.495948] br-lan: port 2(wlan1) entered disabled state
[ 78.501755] device wlan1 entered promiscuous mode
[ 79.025567] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 79.032384] br-lan: port 2(wlan1) entered blocking state
[ 79.037880] br-lan: port 2(wlan1) entered forwarding state
[ 81.878587] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 81.895677] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 81.902195] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 81.910486] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 81.975011] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[ 81.989387] ath10k_pci 0000:00:00.0: rts threshold -1
[ 82.015533] br-lan: port 3(wlan0) entered blocking state
[ 82.021030] br-lan: port 3(wlan0) entered disabled state
[ 82.026923] device wlan0 entered promiscuous mode
[ 82.443642] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 82.450623] br-lan: port 3(wlan0) entered blocking state
[ 82.456174] br-lan: port 3(wlan0) entered forwarding state