Hello dear community. I’m having a hard time with my ethernet connection. It’s there, it does show in the openwrt webui, but then when I connect the cable it doesn’t do anything. And when I have used it in Armbian alone (without openwrt) it does work. Meaning, it’s not broken. What am I missing?
I wanted or intended at least, to add a
log. But couldn’t find a way to download one from the web UI.
Please attach the output of ubus call system board.
It appears you are using firmware that is not from the official OpenWrt project.
When using forks/offshoots/vendor-specific builds that are "based on OpenWrt", there may be many differences compared to the official versions (hosted by OpenWrt.org). Some of these customizations may fundamentally change the way that OpenWrt works. You might need help from people with specific/specialized knowledge about the firmware you are using, so it is possible that advice you get here may not be useful.
You may find that the best options are:
If you believe that this specific issue is common to generic/official OpenWrt and/or the maintainers of your build have indicated as such, please feel free to clarify.
is this it?
BTW im using an extra usb eth wich is eth1 and a usb wifi adapter
[ 12.301939] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 12.369457] meson8b-dwmac c9410000.ethernet eth0: PHY [mdio_mux-0.e40908ff:08] driver [Meson GXL Internal PHY] (irq=35)
[ 13.894654] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found
[ 13.894717] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW
[ 13.896177] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rmii link mode
[ 18.003280] mount_root: mounting /dev/root
[ 18.016780] mount_root: loading kmods from internal overlay
[ 18.326730] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 18.334539] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 18.523460] block: attempting to load /etc/config/fstab
[ 18.527019] block: extroot: device not present, retrying in 5 seconds
[ 23.635637] block: extroot: cannot find device with UUID 9786f8e1-48ca-4bc6-a417-3e50d3f4e652
[ 23.660901] urandom-seed: Seeding with /etc/urandom.seed
[ 24.184277] procd: - early -
[ 24.773451] procd: - ubus -
[ 24.826277] procd: - init -
[ 25.086814] urngd: v1.0.2 started.
[ 25.734023] kmodloader: loading kernel modules from /etc/modules.d/*
[ 25.741871] "cryptomgr_test" (858) uses obsolete ecb(arc4) skcipher
[ 25.768179] Key type dns_resolver registered
[ 25.788880] Key type cifs.spnego registered
[ 25.788900] Key type cifs.idmap registered
[ 25.827646] RPC: Registered named UNIX socket transport module.
[ 25.827662] RPC: Registered udp transport module.
[ 25.827665] RPC: Registered tcp transport module.
[ 25.827668] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 25.839732] tun: Universal TUN/TAP device driver, 1.6
[ 25.869900] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 25.932228] NFS: Registering the id_resolver key type
[ 25.932265] Key type id_resolver registered
[ 25.932270] Key type id_legacy registered
[ 26.118275] cryptodev: driver 1.12 loaded.
[ 26.128100] ntfs3: Max link count 4000
[ 26.128119] ntfs3: Enabled Linux POSIX ACLs support
[ 26.128122] ntfs3: Read-only LZX/Xpress compression included
[ 26.141454] usbcore: registered new interface driver asix
[ 26.142834] usbcore: registered new interface driver ax88179_178a
[ 26.148084] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 26.149123] usbcore: registered new interface driver cdc_eem
[ 26.150903] usbcore: registered new interface driver cdc_ncm
[ 26.151789] usbcore: registered new interface driver cdc_subset
[ 26.153067] usbcore: registered new interface driver dm9601
[ 26.156449] e1000e: Intel(R) PRO/1000 Network Driver
[ 26.156463] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 26.157703] usbcore: registered new interface driver huawei_cdc_ncm
[ 26.160061] usbcore: registered new interface driver ipheth
[ 26.164633] usbcore: registered new interface driver kalmia
[ 26.165684] usbcore: registered new interface driver kaweth
[ 26.168163] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 26.200109] usbcore: registered new interface driver option
[ 26.200160] usbserial: USB Serial support registered for GSM modem (1-port)
[ 26.204282] pegasus: Pegasus/Pegasus II USB Ethernet driver
[ 26.204387] usbcore: registered new interface driver pegasus
[ 26.205440] usbcore: registered new interface driver plusb
[ 26.208972] usbcore: registered new interface driver qmi_wwan
[ 26.213535] usbcore: registered new interface driver rndis_host
[ 26.214632] usbcore: registered new interface driver rtl8150
[ 26.216219] usbcore: registered new interface driver sierra_net
[ 26.219995] usbcore: registered new interface driver smsc95xx
[ 26.224506] usbcore: registered new interface driver sr9700
[ 26.227639] usbcore: registered new interface driver ums-alauda
[ 26.228434] usbcore: registered new interface driver ums-cypress
[ 26.229264] usbcore: registered new interface driver ums-datafab
[ 26.230022] usbcore: registered new interface driver ums-freecom
[ 26.230969] usbcore: registered new interface driver ums-isd200
[ 26.231787] usbcore: registered new interface driver ums-jumpshot
[ 26.232560] usbcore: registered new interface driver ums-karma
[ 26.233460] usbcore: registered new interface driver ums-sddr09
[ 26.234270] usbcore: registered new interface driver ums-sddr55
[ 26.235124] usbcore: registered new interface driver ums-usbat
[ 26.239056] usbcore: registered new device driver usbip-host
[ 26.240136] usbcore: registered new interface driver usblp
[ 26.242157] vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
[ 26.242429] vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 2
[ 26.242492] vhci_hcd: created sysfs vhci_hcd.0
[ 26.242681] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 26.242698] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 26.242704] usb usb2: Product: USB/IP Virtual Host Controller
[ 26.242709] usb usb2: Manufacturer: Linux 6.1.65-ophub vhci_hcd
[ 26.242714] usb usb2: SerialNumber: vhci_hcd.0
[ 26.243269] hub 2-0:1.0: USB hub found
[ 26.243340] hub 2-0:1.0: 8 ports detected
[ 26.244160] vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
[ 26.244373] vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 3
[ 26.244462] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.244541] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 26.244552] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 26.244558] usb usb3: Product: USB/IP Virtual Host Controller
[ 26.244563] usb usb3: Manufacturer: Linux 6.1.65-ophub vhci_hcd
[ 26.244568] usb usb3: SerialNumber: vhci_hcd.0
[ 26.245106] hub 3-0:1.0: USB hub found
[ 26.245164] hub 3-0:1.0: 8 ports detected
[ 26.277550] xt_time: kernel timezone is -0000
[ 26.288703] Bluetooth: Core ver 2.22
[ 26.288721] Bluetooth: Starting self testing
[ 26.304943] Bluetooth: ECDH test passed in 15836 usecs
[ 26.310378] Bluetooth: SMP test passed in 5225 usecs
[ 26.310424] Bluetooth: Finished self testing
[ 26.310507] NET: Registered PF_BLUETOOTH protocol family
[ 26.310512] Bluetooth: HCI device and connection manager initialized
[ 26.310526] Bluetooth: HCI socket layer initialized
[ 26.310533] Bluetooth: L2CAP socket layer initialized
[ 26.310549] Bluetooth: SCO socket layer initialized
[ 26.311945] Bridge firewalling registered
[ 26.314423] usbcore: registered new interface driver cdc_mbim
[ 26.325189] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 26.365244] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 26.367538] hso: drivers/net/usb/hso.c: Option Wireless
[ 26.367665] usbcore: registered new interface driver hso
[ 26.396965] usbcore: registered new interface driver mt7601u
[ 26.403088] usbcore: registered new interface driver mt7663u
[ 26.414373] usbcore: registered new interface driver mt76x2u
[ 26.424598] PPP generic driver version 2.4.2
[ 26.425942] PPP MPPE Compression module registered
[ 26.427366] NET: Registered PF_PPPOX protocol family
[ 26.429280] r8723bs: module is from the staging directory, the quality is unknown, you have been warned.
[ 26.432738] pnetdev = 00000000c4a293ed
[ 26.476766] usbcore: registered new interface driver RSI-USB WLAN
[ 26.508436] usbcore: registered new interface driver ath10k_usb
[ 26.513521] usbcore: registered new interface driver ath6kl_usb
[ 26.519241] usbcore: registered new interface driver brcmfmac
[ 26.521431] usbcore: registered new interface driver carl9170
[ 26.525484] usbcore: registered new interface driver mt76x0u
[ 26.529365] usbcore: registered new interface driver rt2500usb
[ 26.666935] usb 1-2: reset high-speed USB device number 3 using xhci-hcd
[ 26.833212] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 26.843809] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 26.844291] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 26.845719] usbcore: registered new interface driver rt2800usb
[ 26.854411] usbcore: registered new interface driver rtl8192cu
[ 26.857673] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 27.261975] FAT-fs (mmcblk1p1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 27.286641] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 27.296748] BTRFS info (device mmcblk1p3): using crc32c (crc32c-generic) checksum algorithm
[ 27.299609] BTRFS info (device mmcblk1p3): using free space tree
[ 27.320437] BTRFS info (device mmcblk1p3): enabling ssd optimizations
[ 27.325979] BTRFS info (device mmcblk1p4): using crc32c (crc32c-generic) checksum algorithm
[ 27.329665] BTRFS info (device mmcblk1p4): using free space tree
[ 27.357176] BTRFS info (device mmcblk1p4): enabling ssd optimizations
[ 30.879062] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 30.945320] meson8b-dwmac c9410000.ethernet eth0: PHY [mdio_mux-0.e40908ff:08] driver [Meson GXL Internal PHY] (irq=35)
[ 32.486643] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found
[ 32.488691] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW
[ 32.495507] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rmii link mode
[ 32.504459] br-lan: port 1(eth0) entered blocking state
[ 32.508311] br-lan: port 1(eth0) entered disabled state
[ 32.513751] device eth0 entered promiscuous mode
[ 32.564983] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 32.566622] r8152 1-1:1.0 eth1: carrier on
[ 33.876183] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 33.883947] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.36
[ 34.136120] rtl8723bs: acquire FW from file:rtlwifi/rtl8723bs_nic.bin
[ 35.506054] br-lan: port 2(wlan0) entered blocking state
[ 35.506181] br-lan: port 2(wlan0) entered disabled state
[ 35.512178] device wlan0 entered promiscuous mode
[ 35.591098] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 35.592164] br-lan: port 2(wlan0) entered blocking state
[ 35.597208] br-lan: port 2(wlan0) entered forwarding state
[ 35.602904] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 36.468825] wlan1: authenticate with 7c:1c:f1:61:c4:9c
[ 36.468984] wlan1: 80 MHz not supported, disabling VHT
[ 36.487810] wlan1: send auth to 7c:1c:f1:61:c4:9c (try 1/3)
[ 36.564734] wlan1: authenticated
[ 36.570683] wlan1: associate with 7c:1c:f1:61:c4:9c (try 1/3)
[ 36.664881] wlan1: associate with 7c:1c:f1:61:c4:9c (try 2/3)
[ 36.769501] wlan1: associate with 7c:1c:f1:61:c4:9c (try 3/3)
[ 36.872462] wlan1: association with 7c:1c:f1:61:c4:9c timed out
[ 39.713851] wlan1: authenticate with 7c:1c:f1:61:c4:9c
[ 39.716270] wlan1: 80 MHz not supported, disabling VHT
[ 39.731433] wlan1: send auth to 7c:1c:f1:61:c4:9c (try 1/3)
[ 39.735754] wlan1: authenticated
[ 39.738625] wlan1: associate with 7c:1c:f1:61:c4:9c (try 1/3)
[ 39.746991] wlan1: RX AssocResp from 7c:1c:f1:61:c4:9c (capab=0x1431 status=0 aid=119)
[ 39.755286] wlan1: associated
[ 39.811121] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 39.858803] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by 7c:1c:f1:61:c4:9c
[ 50.155729] docker0: port 1(vethefdd02d) entered blocking state
[ 50.158915] docker0: port 1(vethefdd02d) entered disabled state
[ 50.165806] device vethefdd02d entered promiscuous mode
[ 51.696059] eth0: renamed from veth5ed627a
[ 51.711935] IPv6: ADDRCONF(NETDEV_CHANGE): vethefdd02d: link becomes ready
[ 51.716031] docker0: port 1(vethefdd02d) entered blocking state
[ 51.721617] docker0: port 1(vethefdd02d) entered forwarding state
[ 51.728200] IPv6: ADDRCONF(NETDEV_CHANGE): docker0: link becomes ready
oohhh!! the output to that, sorry i didnt get it the first time. now i had my coffee lol here it is
"kernel": "6.1.65-ophub",
"hostname": "OpenWrt",
"system": "ARMv8 Processor rev 4",
"model": "Amlogic Meson GXL (S905X) P212 Development Board",
"board_name": "amlogic,p212",
"rootfs_type": "btrfs",
"release": {
"distribution": "OpenWrt",
"version": "SNAPSHOT",
"target": "armvirt/64",
"revision": "R2023.12.06",
"description": "OpenWrt "
}
}
As stated above the ‘ophub’ fork is not from the openwrt project.
You need to ask those guys for support