Hi,
I'm having a problem relating to module MT7688H. When the module boot up, I show warning
jffs2: warning: (1) jffs2_get_inode_nodes:Eep. No valid nodes for ino #234
And then, it show in console: root@(none) and cannot connect to internet or wifi.
Could you suggest me how to fix it?
Reinstall OpenWrt.
Reinitialising the overlay should be sufficient, just run jffs2_reset or firstboot.
No need to reinstall.
do you mean run command on serial console?
thank for your suggestion, I think I will try softreset first.
thank for your suggestion, I think I will try softreset first.
Thank for your suggest, I will try and inform the result later.
Yes. Although the JFFS2 messages point to an overlay (writable storage) issue, so that isn't probably your real issue. You should share dmesg output, hopefully that has some pointers.
Note WiFi is never preconfigured on official OpenWrt images.
I use firstboot && reboot now command but it's not worked
Here is dmesg log
root@(none):/# dmesg
[ 0.000000] Linux version 3.18.21 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #5 Fri Nov 20 12:43:14 CET 2015
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] MIPS: machine is MediaTek LinkIt Smart 7688
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803022c0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS2,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=000442e0
[ 0.000000] Readback ErrCtl register=000442e0
[ 0.000000] Memory: 126332K/131072K available (2703K kernel code, 129K rwdata, 344K rodata, 144K init, 190K bss, 4740K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] intc: using register map from devicetree
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource_of_init: no matching clocksources found
[ 0.050000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] pinctrl core: initialized pinctrl subsystem
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] rt2880-pinmux pinctrl: try to register 47 pins ...
[ 0.100000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
[ 0.100000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
[ 0.100000] pinctrl core: add 8 pinmux maps
[ 0.100000] rt2880-pinmux pinctrl: found group selector 14 for gpio
[ 0.100000] rt2880-pinmux pinctrl: found group selector 6 for perst
[ 0.100000] rt2880-pinmux pinctrl: found group selector 5 for refclk
[ 0.100000] rt2880-pinmux pinctrl: found group selector 11 for i2s
[ 0.100000] rt2880-pinmux pinctrl: found group selector 13 for spis
[ 0.100000] rt2880-pinmux pinctrl: found group selector 16 for wled_kn
[ 0.100000] rt2880-pinmux pinctrl: found group selector 15 for wled_an
[ 0.100000] rt2880-pinmux pinctrl: found group selector 7 for wdt
[ 0.100000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 37 (io37) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 36 (io36) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 0 (io0) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 3 (io3) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 15 (io15) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 16 (io16) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 35 (io35) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 35 (io35) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: request pin 38 (io38) for pinctrl
[ 0.100000] rt2880-pinmux pinctrl: failed to lookup the sleep state
[ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.120000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.130000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.140000] Switched to clocksource MIPS
[ 0.150000] NET: Registered protocol family 2
[ 0.150000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.170000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.180000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.190000] TCP: reno registered
[ 0.200000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.220000] NET: Registered protocol family 1
[ 0.230000] PCI: CLS 0 bytes, default 32
[ 0.230000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[ 0.230000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.260000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.280000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.300000] msgmni has been set to 246
[ 0.310000] io scheduler noop registered
[ 0.320000] io scheduler deadline registered (default)
[ 0.330000] pinctrl core: add 1 pinmux maps
[ 0.330000] pinctrl core: add 1 pinmux maps
[ 0.330000] rt2880-pinmux pinctrl: found group selector 1 for pwm0
[ 0.330000] rt2880-pinmux pinctrl: found group selector 0 for pwm1
[ 0.330000] rt2880-pinmux pinctrl: request pin 18 (io18) for 10005000.pwm
[ 0.330000] rt2880-pinmux pinctrl: request pin 19 (io19) for 10005000.pwm
[ 0.330000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.350000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[ 0.350000] pinctrl core: add 1 pinmux maps
[ 0.350000] rt2880-pinmux pinctrl: found group selector 10 for uart0
[ 0.350000] rt2880-pinmux pinctrl: request pin 12 (io12) for 10000c00.uartlite
[ 0.350000] rt2880-pinmux pinctrl: request pin 13 (io13) for 10000c00.uartlite
[ 0.350000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[ 0.360000] pinctrl core: add 1 pinmux maps
[ 0.360000] rt2880-pinmux pinctrl: found group selector 3 for uart1
[ 0.360000] rt2880-pinmux pinctrl: request pin 45 (io45) for 10000d00.uart1
[ 0.360000] rt2880-pinmux pinctrl: request pin 46 (io46) for 10000d00.uart1
[ 0.360000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
[ 0.380000] pinctrl core: add 1 pinmux maps
[ 0.380000] rt2880-pinmux pinctrl: found group selector 2 for uart2
[ 0.380000] rt2880-pinmux pinctrl: request pin 20 (io20) for 10000e00.uart2
[ 0.380000] rt2880-pinmux pinctrl: request pin 21 (io21) for 10000e00.uart2
[ 0.380000] console [ttyS2] disabled
[ 0.390000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
[ 0.410000] console [ttyS2] enabled
[ 0.420000] bootconsole [early0] disabled
[ 0.440000] pinctrl core: add 1 pinmux maps
[ 0.440000] pinctrl core: add 1 pinmux maps
[ 0.440000] rt2880-pinmux pinctrl: found group selector 8 for spi
[ 0.440000] rt2880-pinmux pinctrl: found group selector 12 for spi cs1
[ 0.440000] rt2880-pinmux pinctrl: request pin 7 (io7) for 10000b00.spi
[ 0.440000] rt2880-pinmux pinctrl: request pin 8 (io8) for 10000b00.spi
[ 0.440000] rt2880-pinmux pinctrl: request pin 9 (io9) for 10000b00.spi
[ 0.440000] rt2880-pinmux pinctrl: request pin 10 (io10) for 10000b00.spi
[ 0.440000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi
[ 0.440000] spi-mt7621 10000b00.spi: sys_freq: 193333333
[ 0.450000] m25p80 spi32766.0: found w25q256, expected mx25l25635e
[ 0.470000] m25p80 spi32766.0: w25q256 (32768 Kbytes)
[ 0.480000] m25p80 spi32766.0: using chunked io
[ 0.490000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.500000] Creating 4 MTD partitions on "spi32766.0":
[ 0.510000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.520000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.530000] 0x000000040000-0x000000050000 : "factory"
[ 0.540000] 0x000000050000-0x000002000000 : "firmware"
[ 0.620000] 2 uimage-fw partitions found on MTD device firmware
[ 0.630000] 0x000000050000-0x00000016115b : "kernel"
[ 0.640000] 0x00000016115b-0x000002000000 : "rootfs"
[ 0.650000] mtd: device 5 (rootfs) set to be root filesystem
[ 0.660000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.680000] 0x000001500000-0x000002000000 : "rootfs_data"
[ 0.700000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.720000] mt7621_wdt 10000120.watchdog: Initialized
[ 0.730000] TCP: cubic registered
[ 0.730000] NET: Registered protocol family 17
[ 0.740000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.770000] Bridge firewalling registered
[ 0.770000] 8021q: 802.1Q VLAN Support v1.8
[ 0.790000] mtk-linkit bootstrap: Version :
[ 0.790000] mtk-linkit bootstrap: Revision :
[ 0.810000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.830000] Freeing unused kernel memory: 144K (8031c000 - 80340000)
[ 2.120000] init: Console is alive
[ 2.130000] init: - watchdog -
[ 4.150000] usbcore: registered new interface driver usbfs
[ 4.160000] usbcore: registered new interface driver hub
[ 4.170000] usbcore: registered new device driver usb
[ 4.190000] exFAT: Version 1.2.9
[ 4.210000] SCSI subsystem initialized
[ 4.220000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.230000] ehci-platform: EHCI generic platform driver
[ 4.440000] phy phy-usbphy.0: remote usb device wakeup disabled
[ 4.460000] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 4.460000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.480000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.490000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.520000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.530000] usb usb1: no of_node; not parsing pinctrl DT
[ 4.530000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
[ 4.530000] hub 1-0:1.0: USB hub found
[ 4.540000] hub 1-0:1.0: 1 port detected
[ 4.550000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.560000] ohci-platform: OHCI generic platform driver
[ 4.570000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 4.580000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.600000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.670000] usb usb2: no of_node; not parsing pinctrl DT
[ 4.670000] hub 2-0:1.0: no of_node; not parsing pinctrl DT
[ 4.670000] hub 2-0:1.0: USB hub found
[ 4.680000] hub 2-0:1.0: 1 port detected
[ 4.690000] platform gpio-leds: Driver leds-gpio requests probe deferral
[ 4.710000] MTK MSDC device init.
[ 4.720000] pinctrl core: add 1 pinmux maps
[ 4.720000] rt2880-pinmux pinctrl: found group selector 9 for sdmode
[ 4.720000] rt2880-pinmux pinctrl: request pin 22 (io22) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 23 (io23) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 24 (io24) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 25 (io25) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 26 (io26) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 27 (io27) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 28 (io28) for 10130000.sdhci
[ 4.720000] rt2880-pinmux pinctrl: request pin 29 (io29) for 10130000.sdhci
[ 4.760000] mtk-sd: MediaTek MT6575 MSDC Driver
[ 4.770000] sdhci: Secure Digital Host Controller Interface driver
[ 4.780000] sdhci: Copyright(c) Pierre Ossman
[ 4.790000] platform gpio-leds: Driver leds-gpio requests probe deferral
[ 4.810000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.820000] usbcore: registered new interface driver usb-storage
[ 5.180000] init: - preinit -
[ 6.220000] rt305x-esw 10110000.esw: link changed 0x00
[ 6.420000] random: mktemp urandom read with 10 bits of entropy available
[ 9.230000] rt305x-esw 10110000.esw: link changed 0x01
[ 9.890000] jffs2: error: (369) jffs2_build_inode_pass1: child dir "#87497a18" (ino #234) of dir ino #72 appears to be a hard link
[ 9.920000] jffs2: notice: (369) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.950000] mount_root: switching to jffs2 overlay
[ 9.980000] procd: - early -
[ 9.990000] procd: - watchdog -
[ 10.310000] jffs2: warning: (437) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 10.330000] jffs2: warning: (437) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 10.350000] jffs2: iget() failed for ino #234
[ 10.380000] jffs2: warning: (442) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 10.390000] jffs2: warning: (442) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 10.410000] jffs2: iget() failed for ino #234
[ 10.780000] procd: - ubus -
[ 10.790000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 10.810000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 10.820000] jffs2: iget() failed for ino #234
[ 11.800000] procd: - init -
[ 11.810000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 11.830000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 11.850000] jffs2: iget() failed for ino #234
[ 11.860000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 11.880000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 11.900000] jffs2: iget() failed for ino #234
[ 11.910000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 11.920000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 11.940000] jffs2: iget() failed for ino #234
[ 11.950000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 11.960000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 11.980000] jffs2: iget() failed for ino #234
[ 11.990000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.010000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.020000] jffs2: iget() failed for ino #234
[ 12.030000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.050000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.070000] jffs2: iget() failed for ino #234
[ 12.070000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.090000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.110000] jffs2: iget() failed for ino #234
[ 12.120000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.130000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.150000] jffs2: iget() failed for ino #234
[ 12.160000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.180000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.190000] jffs2: iget() failed for ino #234
[ 12.200000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.220000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.230000] jffs2: iget() failed for ino #234
[ 12.240000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.260000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.280000] jffs2: iget() failed for ino #234
[ 12.290000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.300000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.320000] jffs2: iget() failed for ino #234
[ 12.330000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.340000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.360000] jffs2: iget() failed for ino #234
[ 12.370000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.390000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.400000] jffs2: iget() failed for ino #234
[ 12.410000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.430000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.440000] jffs2: iget() failed for ino #234
[ 12.450000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.470000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.490000] jffs2: iget() failed for ino #234
[ 12.500000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.510000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.530000] jffs2: iget() failed for ino #234
[ 12.540000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.550000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.570000] jffs2: iget() failed for ino #234
[ 12.580000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.600000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.610000] jffs2: iget() failed for ino #234
[ 12.620000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.640000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.650000] jffs2: iget() failed for ino #234
[ 12.660000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.680000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.700000] jffs2: iget() failed for ino #234
[ 12.700000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.720000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.740000] jffs2: iget() failed for ino #234
[ 12.750000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.760000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.780000] jffs2: iget() failed for ino #234
[ 12.790000] jffs2: warning: (1) jffs2_get_inode_nodes: Eep. No valid nodes for ino #234.
[ 12.810000] jffs2: warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #234
[ 12.820000] jffs2: iget() failed for ino #234
[ 12.830000] procd: - init complete -
root@(none):/#
Nothing in there that points to any network interfaces being left unconfigured, from what I can tell.
What's the output of ip a s?
(Pretty ancient and outdated OpenWrt version btw.)
Like I said, reinstalling OpenWrt should work. While at it, I'd recommend installing the latest stable version, instead of that 7 years old one you have now! See https://openwrt.org/toh/seeed/linkit7688
Thank you, I will reinstall. I just want to try all other method before reinstall it
how can I find the version I'm using in the Module. cuz I'm affraid of conflict in packages I developing firmware for MT7688
Doesn't say the exact version, but what you have installed was compiled in 2015, so that's very old.
Hi all
I temporary solved problem by replace module MT7688 with new module
I'm curious why you think it would. The JFFS2 errors are overlay errors. OpenWrt can function without a working overlay (just SquashFS), you just won't be able any settings. So how would reinstalling fix the networking issues?
Because running firstboot apparently didn't fix the overlay, which it should have, if the issue was solely with the overlay?
Edit: I took a second look and OP didn't unmount the overlay first, so perhaps it didn't get reformatted and firstboot only attempted to delete files in it, in which case umounting it and running firstboot would've possibly worked.
That said, OP already said they tossed the module with the issue and switched to another one, so I don't see the point in continuing the discussion, unless OP decides to come back to it.
Hi,
I've tried unmount and then firstboot but the result still the same.
Here is how I did: https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset
Flashing a new sysupgrade image (even if it is the same build as already installed) will cause a re-format of the jffs2.
Sure, but so would jfss2_reset or firstboot, to my knowledge... And with less hassle.
Either way, @LocLe, please fix your topic title so it actually covers your issue(s).
As for your networking problem, you haven't shared any ip output like I asked earlier, nor explained what you tried to configure any network interfaces and what errors you saw?