Hello, @flipy thanks for the build! I'm going to get my hands on the device(s) soon, what would be the best way to install openwrt on it? does it have two partitions like the WRT series? does advanced-reboot work? can I seamlessly switch partitions by following on/off procedures like the WRT series?
It does have two partitions and you can switch between them with the usual 3 reboots or by writing to NVRAM.
Unaware of what advanced-reboot is though.
Best way for both versions is to flash from stock, and my advise is to always keep stock firmware in one of the partitions.
1 Like
Any chance of official support?
@flipy Thanks for building images and supporting this device. I have WHW03 V2, I have 2 router.
I need your help with figuring out the issue that I am facing with currently, excuse my nubeness in advance.
I have decided to open one router about year ago to gain serial access and I have managed to connect to the router. I was playing around to see how firmware was built(more precisely I was trying to understand how I need install your image).
In boot loader section, I have done something wrong, now my router is giving me this error shown in the attached log file. Log file
If you can Identify the problem and help me out with sorting it out, I will be very grateful.
@flipy I just flashed a node and I'm having trouble accessing luci. I've set my ip to static 192.168.1.2 and I'm not getting anything. I'm disassembling it now for serial access. Any tips?
Here's the boot log:
U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] WNC_VELOP_V2_20180718_V1.4 (Jul 18 2018 - 11:26:52)
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010006
NAND: ID = 9590dcad
Vendor = ad
Device = dc
ONFI device found
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
512 MiB
MMC: qca_mmc: 0
[devinfo_relocate] devinfo_relocate[146] malloced DEVINFO at 86ff1240
[devinfo_relocate_spec] ret: 0 , total: 262144 , CONFIG_DEVINFO_SIZE: 262144
PCI0 Link Intialized
In: serial
Out: serial
Err: serial
machid: 8010006
flash_type: 2
#### auto_recovery ####
enabled:1, boot_part:2, maxpartialboots:3
boot_count_buffer_size = 2048, total number = 128
i=6, offset = 0x683000, last_offset = 0x682800
Updating boot_count...
boot->Count:2 ,boot->CheckSum:20110813, offset:0x683000
#### ~~~~~~~~~~~~~ ####
#### auto_recovery check ####
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0xa800000, size 0xd00000
13631488 bytes read: OK
## Booting kernel from FIT Image at 81000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-5.4.137
Type: Kernel Image
Compression: uncompressed
Data Start: 0x810000e4
Data Size: 2702160 Bytes = 2.6 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 78702e66
Hash algo: sha1
Hash value: 3b5ed3963b135b5c88b8057ad94c641671787f52
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 81000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt linksys_whw03v2 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x81293d70
Data Size: 18417 Bytes = 18 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 4a38141b
Hash algo: sha1
Hash value: 50ea672a1dc27e54c0acf3d28538a81d72369c80
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x81293d70
Loading Kernel Image ... OK
OK
Loading Device Tree to 86fe7000, end 86fee7f0 ... OK
Andrew: mtdparts="mtdparts=nand0:1024K@0x0(0:SBL1),1024K@0x100000(0:MIBIB),1024K@0x200000(0:QSEE),512K@0x300000(0:CDT),2M@0x380000(0:APPSBL),512K@0x580000(0:ART),512K@0x600000(u_env),256K@0x680000(s_env),256K@0x6c0000(devinfo),161M@0x700000(kernel),155M@0xd00000(rootfs),161M@0xa800000(alt_kernel),155M@0xae00000(alt_rootfs),2M@0x14900000(sysdiag),181M@0x14b00000(syscfg),"
Device nand2 not found!
Using machid 0x8010006 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.137 (acalvo@runtoo) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15879-3b6c93298c)) #0 SMP Wed Aug 4 07:31:51 2021
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys WHW03 V2 (Velop)
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 15 pages/cpu s30092 r8192 d23156 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129408
[ 0.000000] Kernel command line: init=/sbin/init rootfstype=ubifs ubi.mtd=alt_rootfs root=ubi0:ubifs rootwait rw root=/dev/ubiblock0_0 rootfstype=squashfs ro
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 507252K/522240K available (5570K kernel code, 185K rwdata, 1468K rodata, 1024K init, 232K bss, 14988K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x2f0/0x49c with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000022] Switching to timer-based delay loop, resolution 20ns
[ 0.000245] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000261] pid_max: default: 32768 minimum: 301
[ 0.000465] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000480] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001480] CPU: Testing write buffer coherency: ok
[ 0.002512] Setting up static identity map for 0x80300000 - 0x80300060
[ 0.002651] rcu: Hierarchical SRCU implementation.
[ 0.003087] smp: Bringing up secondary CPUs ...
[ 0.006149] smp: Brought up 1 node, 4 CPUs
[ 0.006169] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.006177] CPU: All CPU(s) started in SVC mode.
[ 0.011400] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.011558] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.011583] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.011788] pinctrl core: initialized pinctrl subsystem
[ 0.012834] NET: Registered protocol family 16
[ 0.013199] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.014429] cpuidle: using governor ladder
[ 0.014475] cpuidle: using governor menu
[ 0.035072] cryptd: max_cpu_qlen set to 1000
[ 0.038442] usbcore: registered new interface driver usbfs
[ 0.038509] usbcore: registered new interface driver hub
[ 0.038567] usbcore: registered new device driver usb
[ 0.038615] pps_core: LinuxPPS API ver. 1 registered
[ 0.038624] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.038651] PTP clock support registered
[ 0.039357] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.040538] clocksource: Switched to clocksource arch_sys_counter
[ 0.041323] thermal_sys: Registered thermal governor 'step_wise'
[ 0.041615] NET: Registered protocol family 2
[ 0.041791] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.042533] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.042576] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.042638] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.042727] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.042838] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.042876] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.043127] NET: Registered protocol family 1
[ 0.043169] PCI: CLS 0 bytes, default 64
[ 0.045191] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.051013] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.051027] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.103600] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges:
[ 0.103652] qcom-pcie 40000000.pci: IO 0x40200000..0x402fffff -> 0x40200000
[ 0.103682] qcom-pcie 40000000.pci: MEM 0x40300000..0x40ffffff -> 0x40300000
[ 0.382111] qcom-pcie 40000000.pci: Link up
[ 0.382277] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[ 0.382297] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.382316] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff])
[ 0.382330] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff]
[ 0.382373] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400
[ 0.382413] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 0.382488] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.384079] PCI: bus0: Fast back to back transfers disabled
[ 0.384307] pci 0000:01:00.0: [168c:0056] type 00 class 0x028000
[ 0.384525] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.385237] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.386979] PCI: bus1: Fast back to back transfers disabled
[ 0.387031] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff]
[ 0.387049] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff]
[ 0.387070] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit]
[ 0.387148] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.387165] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff]
[ 0.389974] pcieport 0000:00:00.0: AER: enabled with IRQ 95
[ 0.391797] bam-dma-engine 8e04000.dma: num-channels unspecified in dt
[ 0.391818] bam-dma-engine 8e04000.dma: num-ees unspecified in dt
[ 0.393103] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.393197] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.393282] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.393369] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.393702] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.394274] msm_serial 78af000.serial: msm_serial: detected port #0
[ 0.394317] msm_serial 78af000.serial: uartclk = 1843200
[ 0.394368] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM
[ 0.394392] msm_serial: console setup on port #0
[ 1.029388] printk: console [ttyMSM0] enabled
[ 1.034326] msm_serial: driver initialized
[ 1.043379] loop: module loaded
[ 1.044578] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc
[ 1.045340] nand: Hynix H27U4G8F2EDA-BC
[ 1.051995] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 1.055568] ------------[ cut here ]------------
[ 1.063182] WARNING: CPU: 0 PID: 1 at drivers/mtd/nand/raw/nand_base.c:5579 nand_scan_with_ids+0x178c/0x1790
[ 1.068001] No oob scheme defined for oobsize 0
[ 1.077818] Modules linked in:
[ 1.082075] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.137 #0
[ 1.085180] Hardware name: Generic DT based system
[ 1.091364] [<c030e524>] (unwind_backtrace) from [<c030afa8>] (show_stack+0x10/0x14)
[ 1.095961] [<c030afa8>] (show_stack) from [<c0855224>] (dump_stack+0x94/0xa8)
[ 1.103857] [<c0855224>] (dump_stack) from [<c03213cc>] (__warn+0xbc/0xd8)
[ 1.110884] [<c03213cc>] (__warn) from [<c032146c>] (warn_slowpath_fmt+0x84/0x94)
[ 1.117746] [<c032146c>] (warn_slowpath_fmt) from [<c065b444>] (nand_scan_with_ids+0x178c/0x1790)
[ 1.125300] [<c065b444>] (nand_scan_with_ids) from [<c0661ddc>] (qcom_nandc_probe+0x514/0x93c)
[ 1.134157] [<c0661ddc>] (qcom_nandc_probe) from [<c06294a8>] (platform_drv_probe+0x34/0x70)
[ 1.142662] [<c06294a8>] (platform_drv_probe) from [<c0627b24>] (really_probe+0x1f0/0x358)
[ 1.151253] [<c0627b24>] (really_probe) from [<c0628070>] (device_driver_attach+0x58/0x60)
[ 1.159327] [<c0628070>] (device_driver_attach) from [<c06280d0>] (__driver_attach+0x58/0xcc)
[ 1.167569] [<c06280d0>] (__driver_attach) from [<c0626068>] (bus_for_each_dev+0x68/0x8c)
[ 1.176166] [<c0626068>] (bus_for_each_dev) from [<c0626fec>] (bus_add_driver+0x1c8/0x1d8)
[ 1.184325] [<c0626fec>] (bus_add_driver) from [<c0628658>] (driver_register+0x74/0x108)
[ 1.192484] [<c0628658>] (driver_register) from [<c0302764>] (do_one_initcall+0x84/0x1d8)
[ 1.200736] [<c0302764>] (do_one_initcall) from [<c0b00fdc>] (kernel_init_freeable+0x1d4/0x27c)
[ 1.208808] [<c0b00fdc>] (kernel_init_freeable) from [<c086b064>] (kernel_init+0x8/0x114)
[ 1.217311] [<c086b064>] (kernel_init) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 1.225638] Exception stack(0xdf43bfb0 to 0xdf43bff8)
[ 1.233102] bfa0: 00000000 00000000 00000000 00000000
[ 1.238229] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.246386] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 1.254594] ---[ end trace fcb001e2a5155f6b ]---
[ 1.260991] 8<--- cut here ---
[ 1.265822] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[ 1.268694] pgd = (ptrval)
[ 1.276928] [00000008] *pgd=00000000
[ 1.279457] Internal error: Oops: 5 [#1] SMP ARM
[ 1.283182] Modules linked in:
[ 1.287785] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 5.4.137 #0
[ 1.290651] Hardware name: Generic DT based system
[ 1.298207] PC is at devres_remove+0x34/0xb4
[ 1.302802] LR is at devres_remove+0x78/0xb4
[ 1.307227] pc : [<c062a7f4>] lr : [<c062a838>] psr: 00000093
[ 1.311484] sp : df43bde8 ip : 00000000 fp : 20000013
[ 1.317471] r10: df5818f0 r9 : c062a8a4 r8 : c062b578
[ 1.322679] r7 : df416840 r6 : df5818f4 r5 : df581810 r4 : 00000000
[ 1.327893] r3 : 00000000 r2 : df416840 r1 : df416840 r0 : df581810
[ 1.334492] Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
[ 1.341003] Control: 10c5387d Table: 8020406a DAC: 00000051
[ 1.348201] Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
[ 1.354019] Stack: (0xdf43bde8 to 0xdf43c000)
[ 1.360100] bde0: df416840 ffffffea df5ec580 dfb752c4 df581800 df517840
[ 1.364360] be00: df5ec598 df416840 c090d3b0 c062b0d0 ffffffea c062b20c ffffffea c06620b4
[ 1.372520] be20: 00000000 00000000 df75c480 df581810 dfb75098 c096e370 c06641a4 df581810
[ 1.380679] be40: c0c223a4 df581810 c0c223a4 c0c632bc 00000000 00000000 c0c223a4 00000000
[ 1.388837] be60: dfffcd80 c06294a8 c0c632c4 df581810 c0c632bc c0627b24 df581810 00000000
[ 1.396996] be80: c0c223a4 00000000 00000000 c0b2d834 00000007 c0628070 00000000 c0c223a4
[ 1.405158] bea0: df581810 c06280d0 df581810 c0c223a4 c0628078 c0626068 df409d58 df510d34
[ 1.413319] bec0: c0c223a4 df726800 c0c20590 c0626fec c096e434 00000000 c0c223a4 c0c223a4
[ 1.421476] bee0: c0c2f014 ffffe000 c0b17438 c0628658 c0c04e48 c0c2f014 ffffe000 c0302764
[ 1.429637] bf00: dfffcdfa 00000000 c09df1e8 00000000 dfffcdfa c033cdb4 00000000 c0982f20
[ 1.437796] bf20: 00000006 00000006 c0910ab4 00000000 c091ac44 c0910b28 dfffcdfa 00000000
[ 1.445957] bf40: 00000000 00000006 c0b004a8 9152114c c0b383d0 c0b004a8 c0c2f028 c0c2f010
[ 1.454114] bf60: c0b2d854 c0b00fdc 00000006 00000006 00000000 c0b004a8 00000000 00000072
[ 1.462276] bf80: 00000000 00000000 c086b05c 00000000 00000000 00000000 00000000 00000000
[ 1.470434] bfa0: 00000000 c086b064 00000000 c03010e8 00000000 00000000 00000000 00000000
[ 1.478596] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.486753] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 1.494920] [<c062a7f4>] (devres_remove) from [<c062b0d0>] (devres_destroy+0x8/0x24)
[ 1.503074] [<c062b0d0>] (devres_destroy) from [<c062b20c>] (devm_kfree+0x3c/0x60)
[ 1.510885] [<c062b20c>] (devm_kfree) from [<c06620b4>] (qcom_nandc_probe+0x7ec/0x93c)
[ 1.518263] [<c06620b4>] (qcom_nandc_probe) from [<c06294a8>] (platform_drv_probe+0x34/0x70)
[ 1.526163] [<c06294a8>] (platform_drv_probe) from [<c0627b24>] (really_probe+0x1f0/0x358)
[ 1.534759] [<c0627b24>] (really_probe) from [<c0628070>] (device_driver_attach+0x58/0x60)
[ 1.542830] [<c0628070>] (device_driver_attach) from [<c06280d0>] (__driver_attach+0x58/0xcc)
[ 1.551079] [<c06280d0>] (__driver_attach) from [<c0626068>] (bus_for_each_dev+0x68/0x8c)
[ 1.559670] [<c0626068>] (bus_for_each_dev) from [<c0626fec>] (bus_add_driver+0x1c8/0x1d8)
[ 1.567830] [<c0626fec>] (bus_add_driver) from [<c0628658>] (driver_register+0x74/0x108)
[ 1.575994] [<c0628658>] (driver_register) from [<c0302764>] (do_one_initcall+0x84/0x1d8)
[ 1.584241] [<c0302764>] (do_one_initcall) from [<c0b00fdc>] (kernel_init_freeable+0x1d4/0x27c)
[ 1.592311] [<c0b00fdc>] (kernel_init_freeable) from [<c086b064>] (kernel_init+0x8/0x114)
[ 1.600818] [<c086b064>] (kernel_init) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 1.609142] Exception stack(0xdf43bfb0 to 0xdf43bff8)
[ 1.616606] bfa0: 00000000 00000000 00000000 00000000
[ 1.621739] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.629895] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 1.638056] Code: e28560e4 e1560004 e1a0b000 0a000008 (e5943008)
[ 1.644473] ---[ end trace fcb001e2a5155f6c ]---
[ 1.650720] Kernel panic - not syncing: Fatal exception
[ 1.655416] CPU3: stopping
[ 1.660354] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G D W 5.4.137 #0
[ 1.663133] Hardware name: Generic DT based system
[ 1.670695] [<c030e524>] (unwind_backtrace) from [<c030afa8>] (show_stack+0x10/0x14)
[ 1.675296] [<c030afa8>] (show_stack) from [<c0855224>] (dump_stack+0x94/0xa8)
[ 1.683197] [<c0855224>] (dump_stack) from [<c030d7d8>] (handle_IPI+0x164/0x19c)
[ 1.690232] [<c030d7d8>] (handle_IPI) from [<c05af9c4>] (gic_handle_irq+0x8c/0x90)
[ 1.697782] [<c05af9c4>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[ 1.705149] Exception stack(0xdf475f60 to 0xdf475fa8)
[ 1.712704] 5f60: 00000000 00000280 dfb64234 c0313c40 ffffe000 c0c04e68 c0c04ea8 00000008
[ 1.717744] 5f80: 00000000 c0b3ede8 c0c0df40 00000000 00000000 df475fb0 c03083c0 c03083c4
[ 1.725898] 5fa0: 60000013 ffffffff
[ 1.734057] [<c0301a8c>] (__irq_svc) from [<c03083c4>] (arch_cpu_idle+0x38/0x3c)
[ 1.737365] [<c03083c4>] (arch_cpu_idle) from [<c0349e08>] (do_idle+0x1e4/0x21c)
[ 1.745002] [<c0349e08>] (do_idle) from [<c034a0d0>] (cpu_startup_entry+0x18/0x1c)
[ 1.752379] [<c034a0d0>] (cpu_startup_entry) from [<803024ac>] (0x803024ac)
[ 1.759754] CPU2: stopping
[ 1.766604] CPU: 2 PID: 0 Comm: swapper/2 Tainted: G D W 5.4.137 #0
[ 1.769383] Hardware name: Generic DT based system
[ 1.776944] [<c030e524>] (unwind_backtrace) from [<c030afa8>] (show_stack+0x10/0x14)
[ 1.781547] [<c030afa8>] (show_stack) from [<c0855224>] (dump_stack+0x94/0xa8)
[ 1.789444] [<c0855224>] (dump_stack) from [<c030d7d8>] (handle_IPI+0x164/0x19c)
[ 1.796478] [<c030d7d8>] (handle_IPI) from [<c05af9c4>] (gic_handle_irq+0x8c/0x90)
[ 1.804031] [<c05af9c4>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[ 1.811398] Exception stack(0xdf473f60 to 0xdf473fa8)
[ 1.818956] 3f60: 00000000 00000138 dfb55234 c0313c40 ffffe000 c0c04e68 c0c04ea8 00000004
[ 1.823993] 3f80: 00000000 c0b3ede8 c0c0df40 00000000 c0c04e78 df473fb0 c03083c0 c03083c4
[ 1.832148] 3fa0: 60000013 ffffffff
[ 1.840307] [<c0301a8c>] (__irq_svc) from [<c03083c4>] (arch_cpu_idle+0x38/0x3c)
[ 1.843611] [<c03083c4>] (arch_cpu_idle) from [<c0349e08>] (do_idle+0x1e4/0x21c)
[ 1.851250] [<c0349e08>] (do_idle) from [<c034a0d0>] (cpu_startup_entry+0x18/0x1c)
[ 1.858625] [<c034a0d0>] (cpu_startup_entry) from [<803024ac>] (0x803024ac)
[ 1.866002] CPU1: stopping
[ 1.872853] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D W 5.4.137 #0
[ 1.875635] Hardware name: Generic DT based system
[ 1.883193] [<c030e524>] (unwind_backtrace) from [<c030afa8>] (show_stack+0x10/0x14)
[ 1.887798] [<c030afa8>] (show_stack) from [<c0855224>] (dump_stack+0x94/0xa8)
[ 1.895695] [<c0855224>] (dump_stack) from [<c030d7d8>] (handle_IPI+0x164/0x19c)
[ 1.902727] [<c030d7d8>] (handle_IPI) from [<c05af9c4>] (gic_handle_irq+0x8c/0x90)
[ 1.910280] [<c05af9c4>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[ 1.917649] Exception stack(0xdf471f60 to 0xdf471fa8)
[ 1.925204] 1f60: 00000000 000000a4 dfb46234 c0313c40 ffffe000 c0c04e68 c0c04ea8 00000002
[ 1.930245] 1f80: 00000000 c0b3ede8 c0c0df40 00000000 c0c04f10 df471fb0 c03083c0 c03083c4
[ 1.938397] 1fa0: 60000013 ffffffff
[ 1.946557] [<c0301a8c>] (__irq_svc) from [<c03083c4>] (arch_cpu_idle+0x38/0x3c)
[ 1.949863] [<c03083c4>] (arch_cpu_idle) from [<c0349e08>] (do_idle+0x1e4/0x21c)
[ 1.957498] [<c0349e08>] (do_idle) from [<c034a0d0>] (cpu_startup_entry+0x18/0x1c)
[ 1.964876] [<c034a0d0>] (cpu_startup_entry) from [<803024ac>] (0x803024ac)
[ 1.972255] Rebooting in 1 seconds..
[ 3.979280] Reboot failed -- System halted
I have a v2 device, and after installing the 0.0.6 v2 firmware, I too get a solid blue light, and the device is inaccessible. After 3 power cycles, I'm able to get back to the Linksys OEM firmware.
@flipy , I've seen that you have commits in your repository in October, and your latest release is from August. Do you have a newer release?
Could you resend the log file again?
Looks like it is not loading the partition on the NAND correctly, and cannot boot successfully.
It is not the first time someone has reported a similar situation.
Could you share your device hw version?
I'm afraid there is a difference with the versions I have and I'll need to create a new device model.
I do try to update from the official 21.02 branch from time to time, but latest release should work.
It might be related to @Nico1320 problem, can you provide a boot log?
It's WHW03v2, I've tried to boot initramfs to no avail.
Hi!
If the kernel still crashes loading from initram will not help.
If you have access to a shell on the Linksys firmware, by using the support password, you could get the device tree and I'd be able to work a identify the difference and build an image.
Unfortunately I returned the device already.
I have access to shell, but how do I exactly dump everything? I know dts-related files are in /proc/device-tree
@flipy I compiled and compared the device tree that @jms19 provided and it's basically the same as mine
Is there any guide I can check on how to convert the @flipy files to a .img that I can load using the /fwupdate.html URL from the Velop factory firmware? Or how to use the .bin files? Apologies for the newbie questions in advance. I have the Velop V1 WHW03 but do not have the background on how to use the builds.
You should flash *factory.bin for your hardware version. in your case; https://github.com/flipy/openwrt/releases/download/whw03-0.0.7/openwrt-ipq40xx-generic-linksys_whw03-squashfs-factory.bin
I tried using the .bin file but get the error
Blockquote "result": "ErrorUnauthorized"
I am using the /fwupdate.html web based link available from the factory firmware. Is there a different method that allow the .bin file upload to the equipment?