Reboots when using LuCI might point toward something in the authentication components, rpcd etc. that time care for the ACL stuff, or uhttpd But my build contains nothing special regarding them. And if there would be a generic bug in those, there would likely be more bug reports about it (especially strange is 19.07.x).
Thanks for the replies I will try to do some more testing later this afternoon.
It must be a fault with my device or issue with my browsers or extensions (Vivaldi, but I also tested with chrome on my PC and phone) As there are no other reports except https://forum.openwrt.org/t/build-for-netgear-r7800/316/2557
I would love to find out why but may have to admit defeat and stick with the standard build and add the packages I need.
So far I haven't installed the SSL package for LuCI on the standard build. Do you think this could be the cause of any of my issues?
Hard to say. It might be SSL, but in that case there would surely be more reports.
Seems a bit weird that the router reboots tho', what would really cause the linux kernel to do that just by simply going to a webpage that's hosted on the router?
I think I have the same problem.
It is not that the router reboots, but LuCI isn't loading correctly and has issues, CLI seems to work.
But I prefer LuCI.
I also have SSL package installed, to create a VPN Server.
Restored the backup created before the sysupgrade to r14533.
OpenVPN seems to be missing.
Still got some LuCI issues so did a sysupgrade back to previous version: r14023
Everything seems to work normal again, without OpenVPN. Will now try to upgrade to r14533.
Upgrade to version R14533 gives some issues.
See screenshots.
Can only add 1 images, other screenshots gives the error:
Error
XHR request aborted by browser
I have just flashed owrt1907-r11211-34a9652904-20200919 via TFTP.
Here is the kernel log (truncated due to character restriction on post)
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.195 (perus@ub2004) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11104-e752fc1ff9)) #0 SMP Sat Sep 19 16:55:48 2020
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c0b25580, node_mem_map dda39000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x40c with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29324 r8192 d23924 u61440
[ 0.000000] pcpu-alloc: s29324 r8192 d23924 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line:
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 476368K/491520K available (4846K kernel code, 151K rwdata, 1268K rodata, 1024K init, 228K bss, 15152K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc07bb978 (5839 kB)
[ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB)
[ 0.000000] .data : 0xc0b00000 - 0xc0b25e80 ( 152 kB)
[ 0.000000] .bss : 0xc0b27000 - 0xc0b60118 ( 229 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000022] Switching to timer-based delay loop, resolution 160ns
[ 0.000220] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000246] pid_max: default: 32768 minimum: 301
[ 0.000373] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000388] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000949] CPU: Testing write buffer coherency: ok
[ 0.001705] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.001861] Hierarchical SRCU implementation.
[ 0.002576] smp: Bringing up secondary CPUs ...
[ 0.004396] smp: Brought up 1 node, 2 CPUs
[ 0.004413] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.004424] CPU: All CPU(s) started in SVC mode.
[ 0.014506] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.014668] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.014693] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.014792] pinctrl core: initialized pinctrl subsystem
[ 0.015763] NET: Registered protocol family 16
[ 0.016018] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.017271] cpuidle: using governor ladder
[ 0.017335] cpuidle: using governor menu
[ 0.039259] msm_bus_fabric_init_driver
[ 0.040630] usbcore: registered new interface driver usbfs
[ 0.040709] usbcore: registered new interface driver hub
[ 0.040795] usbcore: registered new device driver usb
[ 0.040852] pps_core: LinuxPPS API ver. 1 registered
[ 0.040863] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.040896] PTP clock support registered
[ 0.042742] clocksource: Switched to clocksource dg_timer
[ 0.045689] NET: Registered protocol family 2
[ 0.046212] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.046256] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.046309] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.046396] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.046424] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.046608] NET: Registered protocol family 1
[ 0.046656] PCI: CLS 0 bytes, default 64
[ 0.047769] No memory allocated for crashlog
[ 0.048047] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.052242] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.052259] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.060873] io scheduler noop registered
[ 0.060892] io scheduler deadline registered (default)
[ 0.062577] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.062687] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.062778] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.063657] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[ 0.063698] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.063723] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.171091] qcom-pcie 1b500000.pci: link up
[ 0.171240] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.171263] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.171283] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.171299] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.171316] pci_bus 0000:00: scanning bus
[ 0.171365] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.171460] pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x44
[ 0.171531] pci 0000:00:00.0: supports D1
[ 0.171541] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.171558] pci 0000:00:00.0: PME# disabled
[ 0.171798] pci_bus 0000:00: fixups for bus
[ 0.171821] PCI: bus0: Fast back to back transfers disabled
[ 0.171842] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.171964] pci_bus 0000:01: scanning bus
[ 0.172143] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.172495] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.173066] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x44
[ 0.173708] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.173749] pci 0000:01:00.0: PME# disabled
[ 0.174064] pci_bus 0000:01: fixups for bus
[ 0.174136] PCI: bus1: Fast back to back transfers disabled
[ 0.174156] pci_bus 0000:01: bus scan returning with max=01
[ 0.174174] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.174191] pci_bus 0000:00: bus scan returning with max=ff
[ 0.174239] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.174264] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.174392] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.174414] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.174452] pci 0000:00:00.0: calling qcom_pcie_fixup_final+0x0/0x94
[ 0.174636] pcieport 0000:00:00.0: assign IRQ: got 67
[ 0.174950] pcieport 0000:00:00.0: AER enabled with IRQ 35
[ 0.175066] pci 0000:01:00.0: calling qcom_pcie_fixup_final+0x0/0x94
[ 0.175481] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.175592] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.175684] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.176417] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[ 0.176453] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.176478] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.286236] qcom-pcie 1b700000.pci: link up
[ 0.286381] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.286401] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.286418] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.286434] pci_bus 0001:00: scanning bus
[ 0.286475] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.286552] pci 0001:00:00.0: calling pci_fixup_ide_bases+0x0/0x44
[ 0.286616] pci 0001:00:00.0: supports D1
[ 0.286627] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.286641] pci 0001:00:00.0: PME# disabled
[ 0.286860] pci_bus 0001:00: fixups for bus
[ 0.286879] PCI: bus0: Fast back to back transfers disabled
[ 0.286896] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.287009] pci_bus 0001:01: scanning bus
[ 0.287195] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.287565] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.288068] pci 0001:01:00.0: calling pci_fixup_ide_bases+0x0/0x44
[ 0.288759] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.288801] pci 0001:01:00.0: PME# disabled
[ 0.289127] pci_bus 0001:01: fixups for bus
[ 0.289203] PCI: bus1: Fast back to back transfers disabled
[ 0.289217] pci_bus 0001:01: bus scan returning with max=01
[ 0.289233] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.289250] pci_bus 0001:00: bus scan returning with max=ff
[ 0.289287] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.289311] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.289443] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.289463] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.289494] pci 0001:00:00.0: calling qcom_pcie_fixup_final+0x0/0x94
[ 0.289675] pcieport 0001:00:00.0: assign IRQ: got 100
[ 0.289940] pcieport 0001:00:00.0: AER enabled with IRQ 68
[ 0.290053] pci 0001:01:00.0: calling qcom_pcie_fixup_final+0x0/0x94
[ 0.292269] L2 @ QSB rate. Forcing new rate.
[ 0.292483] L2 @ 384000 KHz
[ 0.292656] CPU0 @ 800000 KHz
[ 0.292669] CPU1 @ QSB rate. Forcing new rate.
[ 0.292795] CPU1 @ 384000 KHz
[ 0.296694] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.298580] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.299367] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.299469] msm_serial 16340000.serial: uartclk = 7372800
[ 0.299555] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 101, base_baud = 460800) is a MSM
[ 0.299596] msm_serial: console setup on port #0
[ 1.020209] console [ttyMSM0] enabled
[ 1.024973] msm_serial: driver initialized
[ 1.033237] loop: module loaded
[ 1.035291] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.035326] nand: AMD/Spansion S34MS01G2
[ 1.041894] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.045994] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.053279] Creating 8 MTD partitions on "qcom_nand.0":
[ 1.060041] 0x000000000000-0x000000c80000 : "qcadata"
[ 1.070210] random: fast init done
[ 1.088170] 0x000000c80000-0x000001180000 : "APPSBL"
[ 1.097747] 0x000001180000-0x000001200000 : "APPSBLENV"
[ 1.099349] 0x000001200000-0x000001340000 : "art"
[ 1.104695] 0x000001340000-0x000001480000 : "artbak"
[ 1.109561] 0x000001480000-0x000001880000 : "kernel"
[ 1.119468] 0x000001880000-0x000007900000 : "ubi"
[ 1.290757] 0x000007900000-0x000008000000 : "reserve"
[ 1.305109] libphy: GPIO Bitbanged MDIO: probed
[ 1.326522] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.184960] ar8327: qca,phy-rgmii-en is not specified
[ 2.185343] libphy: Fixed MDIO Bus: probed
[ 2.191172] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 2.193373] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.199499] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 2.204634] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 2.210611] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 2.218678] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 2.226242] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 2.233268] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 2.241075] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 2.246983] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 2.254359] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.262625] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 2.269931] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.276036] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 2.281008] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 2.287156] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 2.295154] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 2.302622] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 2.309744] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 2.317616] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 2.323457] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 2.330749] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.338239] i2c /dev entries driver
[ 2.347018] Calibration not found.
[ 2.350452] Speed bin: 0
[ 2.352785] PVS bin: 3
[ 2.356919] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.357723] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.365509] sdhci: Secure Digital Host Controller Interface driver
[ 2.372149] sdhci: Copyright(c) Pierre Ossman
[ 2.378470] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.384241] NET: Registered protocol family 10
[ 2.389936] Segment Routing with IPv6
[ 2.392878] NET: Registered protocol family 17
[ 2.397304] 8021q: 802.1Q VLAN Support v1.8
[ 2.400914] Registering SWP/SWPB emulation handler
[ 2.417819] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[ 2.433936] s1a: supplied by regulator-dummy
[ 2.434030] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.437533] s1b: supplied by regulator-dummy
[ 2.442271] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.446809] s2a: supplied by regulator-dummy
[ 2.451486] s2a: Bringing 0uV into 775000-775000uV
[ 2.455998] s2b: supplied by regulator-dummy
[ 2.460340] s2b: Bringing 0uV into 775000-775000uV
[ 2.469355] UBI: auto-attach mtd6
[ 2.469375] ubi0: attaching mtd6
[ 2.517808] random: crng init done
[ 2.526906] UBI: EOF marker found, PEBs from 60 will be erased
[ 2.630837] ubi0: scanning is finished
[ 2.657487] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 690 LEBs
[ 2.658034] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[ 2.662896] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.668437] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.675218] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.681995] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 2.688831] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.695081] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 2020257135
[ 2.702051] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[ 2.711492] ubi0: background thread "ubi_bgt0d" started, PID 59
[ 2.712071] block ubiblock0_0: created from ubi0:0(rootfs)
[ 2.726269] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 2.731763] hctosys: unable to open rtc device (rtc0)
[ 5.001156] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.001924] Freeing unused kernel memory: 1024K
[ 5.415789] init: Console is alive
[ 5.416009] init: - watchdog -
[ 6.332189] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.438241] exFAT: Version 1.2.9
[ 6.445691] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.447503] SCSI subsystem initialized
[ 6.453397] libata version 3.00 loaded.
[ 6.455342] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 6.455386] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 6.460309] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 6.469459] scsi host0: ahci
[ 6.477353] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
[ 6.805109] ata1: SATA link down (SStatus 0 SControl 300)
[ 6.806532] ehci-platform: EHCI generic platform driver
[ 6.811748] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.815020] ohci-platform: OHCI generic platform driver
[ 6.950169] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.950244] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 6.954943] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 6.962196] xhci-hcd xhci-hcd.0.auto: irq 105, io mem 0x11000000
[ 6.972151] hub 1-0:1.0: USB hub found
[ 6.977801] hub 1-0:1.0: 1 port detected
[ 6.981470] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.985443] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 6.990664] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 6.998352] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.005187] hub 2-0:1.0: USB hub found
[ 7.013220] hub 2-0:1.0: 1 port detected
[ 7.016910] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.020792] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 7.026274] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 7.033720] xhci-hcd xhci-hcd.1.auto: irq 106, io mem 0x10000000
[ 7.043392] hub 3-0:1.0: USB hub found
[ 7.049274] hub 3-0:1.0: 1 port detected
[ 7.052961] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.056974] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 7.062192] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 7.069876] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.076688] hub 4-0:1.0: USB hub found
[ 7.084801] hub 4-0:1.0: 1 port detected
[ 7.090606] usbcore: registered new interface driver usb-storage
[ 7.092397] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.105723] init: - preinit -
[ 8.675928] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 8.676619] dwmac1000: Master AXI performs any burst length
[ 8.684897] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 8.690278] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 8.699648] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 9.763309] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 9.765553] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 14.875916] mount_root: loading kmods from internal overlay
[ 14.891607] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 14.893785] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 14.932104] print_req_error: I/O error, dev mtdblock0, sector 0
[ 14.932540] print_req_error: I/O error, dev mtdblock0, sector 8
[ 14.937295] print_req_error: I/O error, dev mtdblock0, sector 16
[ 14.943178] print_req_error: I/O error, dev mtdblock0, sector 24
[ 14.949534] print_req_error: I/O error, dev mtdblock0, sector 0
[ 14.954965] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.032550] print_req_error: I/O error, dev mtdblock0, sector 0
[ 15.032576] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.037858] print_req_error: I/O error, dev mtdblock1, sector 0
[ 15.045025] print_req_error: I/O error, dev mtdblock1, sector 8
[ 15.050864] print_req_error: I/O error, dev mtdblock1, sector 16
[ 15.056833] print_req_error: I/O error, dev mtdblock1, sector 24
[ 15.063053] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.070891] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.249856] UBIFS (ubi0:1): default file-system created
[ 15.250912] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 147
[ 15.327469] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.327494] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.334348] UBIFS (ubi0:1): FS size: 86216704 bytes (82 MiB, 679 LEBs), journal size 4317184 bytes (4 MiB, 34 LEBs)
[ 15.344219] UBIFS (ubi0:1): reserved for root: 4072227 bytes (3976 KiB)
[ 15.354468] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID CBF837C0-62C3-4312-9694-D4E409A1D3E0, small LPT model
[ 15.361880] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 15.372600] block: unable to load configuration (fstab: Entry not found)
[ 15.379341] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 15.386296] block: unable to load configuration (fstab: Entry not found)
[ 15.392546] block: attempting to load /etc/config/fstab
[ 15.418818] block: extroot: not configured
[ 15.456103] UBIFS (ubi0:1): un-mount UBI device 0
[ 15.458463] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 15.495122] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 148
[ 15.581340] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.581366] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.588210] UBIFS (ubi0:1): FS size: 86216704 bytes (82 MiB, 679 LEBs), journal size 4317184 bytes (4 MiB, 34 LEBs)
[ 15.598108] UBIFS (ubi0:1): reserved for root: 4072227 bytes (3976 KiB)
[ 15.608323] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID CBF837C0-62C3-4312-9694-D4E409A1D3E0, small LPT model
[ 15.628622] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.634079] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.637809] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.644407] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.814962] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 15.815045] block: unable to load configuration (fstab: Entry not found)
[ 15.820758] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 15.827792] block: unable to load configuration (fstab: Entry not found)
[ 15.834097] block: attempting to load /etc/config/fstab
[ 15.840962] block: extroot: not configured
[ 15.884628] mount_root: overlay filesystem has not been fully initialized yet
[ 15.885095] mount_root: switching to ubifs overlay
[ 15.912164] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 16.015740] procd: - early -
[ 16.015799] procd: - watchdog -
[ 16.690114] procd: - watchdog -
[ 16.690631] procd: - ubus -
[ 16.916251] procd: - init -
[ 17.149231] urngd: v1.0.2 started.
[ 17.168409] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.180955] tun: Universal TUN/TAP device driver, 1.6
[ 17.182676] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 17.188096] gre: GRE over IPv4 demultiplexor driver
[ 17.191363] ip_gre: GRE over IPv4 tunneling driver
[ 17.199796] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.204289] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 17.224866] Netfilter messages via NETLINK v0.30.
[ 17.225739] ip_set: protocol 6
[ 17.238836] Mirror/redirect action on
[ 17.242989] u32 classifier
[ 17.243007] input device check on
[ 17.244655] Actions configured
[ 17.253158] fuse init (API version 7.26)
[ 17.255116] usbcore: registered new interface driver chaoskey
[ 17.256857] Loading modules backported from Linux version v4.19.137-0-gc076c79e03c6
[ 17.261782] Backport generated by backports.git v4.19.137-1-0-g60c3a249
[ 17.270742] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.279156] ctnetlink v0.93: registering with nfnetlink.
[ 17.301682] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information.
[ 17.301708] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 17.321991] xt_time: kernel timezone is -0000
[ 17.343132] PPP generic driver version 2.4.2
[ 17.344149] PPP MPPE Compression module registered
[ 17.347144] NET: Registered protocol family 24
[ 17.351768] PPTP driver version 0.8.5
I compared this with the log when using the standard build of 19.07.4 and the only thing that jumps out is the I/O errors on mtdblock1. These are not in the kernel log with standard build. But I believe this have been addressed before and are considered normal.
Also noticed these differences
[ 0.171964] pci_bus 0000:01: scanning bus
[ 0.172143] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.172495] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.173066] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x44
[ 0.173708] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.173749] pci 0000:01:00.0: PME# disabled
compared with standard build
[ 0.286686] pci_bus 0001:00: scanning bus
[ 0.286728] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.286801] pci 0001:00:00.0: calling 0xc030d3c0
[ 0.286864] pci 0001:00:00.0: supports D1
[ 0.286874] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.286888] pci 0001:00:00.0: PME# disabled
The rest of the log
[ 17.364333] ath10k_pci 0000:01:00.0: assign IRQ: got 67
[ 17.364355] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
[ 17.365087] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 17.371219] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 17.371671] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 17.544656] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[ 17.544688] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 17.750186] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[ 17.750355] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 17.758142] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 17.964460] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/ct-firmware-5.bin failed with error -2
[ 17.964496] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 17.987935] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 17.988100] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/ct-firmware-2.bin failed with error -2
[ 17.996214] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 18.020590] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 18.020754] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2
[ 18.028912] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 18.053026] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 18.289376] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 18.289410] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 18.300148] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-795874169 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 f3d4b769
[ 20.637659] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[ 26.507426] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 26.507455] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 26.589560] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 26.590399] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
[ 26.847043] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 26.941903] ath: EEPROM regdomain: 0x0
[ 26.941916] ath: EEPROM indicates default country code should be used
[ 26.941925] ath: doing EEPROM country->regdmn map search
[ 26.941939] ath: country maps to regdmn code: 0x3a
[ 26.941950] ath: Country alpha2 being used: US
[ 26.941959] ath: Regpair used: 0x3a
[ 26.946524] ath10k_pci 0001:01:00.0: assign IRQ: got 100
[ 26.946560] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
[ 26.947358] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 26.953581] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 26.954214] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 27.125403] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0001:01:00.0.txt failed with error -2
[ 27.125432] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 27.249000] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[ 27.249171] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[ 27.256940] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 27.454144] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/ct-firmware-5.bin failed with error -2
[ 27.454177] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 27.477701] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 27.477844] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/ct-firmware-2.bin failed with error -2
[ 27.485971] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 27.510508] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 27.510655] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2
[ 27.518779] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 27.542945] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 27.543170] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 27.550802] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 27.562802] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-795874169 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 f3d4b769
[ 29.886973] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
[ 35.728696] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 35.728721] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 35.812854] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 35.813732] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
[ 36.026352] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 36.182135] ath: EEPROM regdomain: 0x0
[ 36.182147] ath: EEPROM indicates default country code should be used
[ 36.182155] ath: doing EEPROM country->regdmn map search
[ 36.182170] ath: country maps to regdmn code: 0x3a
[ 36.182181] ath: Country alpha2 being used: US
[ 36.182189] ath: Regpair used: 0x3a
[ 36.190295] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 44.206361] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 44.207048] dwmac1000: Master AXI performs any burst length
[ 44.215345] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 44.220726] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 44.229798] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 44.238100] br-lan: port 1(eth1.1) entered blocking state
[ 44.242418] br-lan: port 1(eth1.1) entered disabled state
[ 44.248138] device eth1.1 entered promiscuous mode
[ 44.253356] device eth1 entered promiscuous mode
[ 44.258943] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 44.267152] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 44.269523] dwmac1000: Master AXI performs any burst length
[ 44.278644] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 44.284112] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 44.293397] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 44.305869] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 44.480373] print_req_error: 14 callbacks suppressed
[ 44.480378] print_req_error: I/O error, dev mtdblock0, sector 0
[ 44.484946] print_req_error: I/O error, dev mtdblock0, sector 8
[ 44.492039] print_req_error: I/O error, dev mtdblock0, sector 16
[ 44.496440] print_req_error: I/O error, dev mtdblock0, sector 24
[ 44.505908] print_req_error: I/O error, dev mtdblock0, sector 0
[ 44.508189] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 44.519734] print_req_error: I/O error, dev mtdblock0, sector 0
[ 44.521121] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 44.529682] print_req_error: I/O error, dev mtdblock1, sector 0
[ 44.539755] print_req_error: I/O error, dev mtdblock1, sector 8
[ 44.540623] print_req_error: I/O error, dev mtdblock1, sector 16
[ 44.546608] print_req_error: I/O error, dev mtdblock1, sector 24
[ 44.555515] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 44.560750] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 45.296780] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 45.299958] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 45.308296] br-lan: port 1(eth1.1) entered blocking state
[ 45.310714] br-lan: port 1(eth1.1) entered forwarding state
[ 45.322191] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 45.389884] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 45.389929] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 45.401091] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
root@OpenWrt:~#
I sometimes get these messages when using LuCI and one of the crashes I have been experiencing happens. I guess because the ajax request did not get a response before it was timed out. A symptom rather than a cause for me at least
If you look at the output again you will see, there are too pci scans, you compared first scan from mine with second scan from your. I see two differences your ubi is larger than mine, it is possible, that the part size changed at some point and my ubifs is so old that it was created before that change. I also see some chaoskey driver load in your output, that module is not included in my build.
Is there anything special attached to your unit e.g. usb device? Does it crash at logon or at certain pages.
I'm a bit confused now, but @KONG, you do realize you're writing in @hnyman's R7800 build thread?
If you and @iamtomb are talking about your build, i suggest you make a new thread about it.
2 Likes
LOL. Sorry I thought you replied to me after I posted the message regarding stable,master and so on:-)
Then it's all good. If it crashes on hnyman build, then maybe he needs to clean his build dir. Official builds are created with buildbot which always starts from a clean tree. Thus they don't run into problems like "not linking against updated libs", which can cause this.
Nope.
I always start from a clean build tree. Have done so the 10 years that I have been publishing community builds here... (For wndr3700 and now for R7800).
2 Likes
The latest release i've applied appears to have trashed my ddns config. when I go in to try and fix it "DDNS Service Provider" drop down only gives me the option of "-- custom --" where I would expect to see options for providers like previously. I wonder if the package has got broken?
It has. See the DDNS discussions in the packages & LuCI bug trackers.
E.g.
and
https://lists.openwrt.org/pipermail/openwrt-devel/2020-September/031507.html
(Nothing to do specifically with my build.)
Thanks for the prompt response 
master-r14627-d6a9a92e32-20201003
There have been recent fixes to the DDNS package, both the package itself and the LuCI side.
Hopefully those fixes do fix your issues.
(I do not use DDNS myself, so no personal experience)
1 Like