Hello, maybe someone can help me.
Router BananaPi BPI R2 Pro with OpenWrt (openwrt-24.10.0-rockchip-armv8-sinovoip_bpi-r2-pro-ext4-sysupgrade.img.gz).
A hard drive is installed in the router.
The problem is data transfer via Samba (SMB).
When I transfer data over the single eth0 interface, I get good transfer rates of 100MB/s both from the PC to the BPI and vice versa. I think that's OK.
When I transfer data over an interface of the 4-port switch, I also get 100MB/s from the PC to the BPI. In the opposite direction, from the BPI to the PC, the transfer rate is initially 355KB/s and then aborts with errors. I've tried every conceivable variation, sometimes with a bridge in between and sometimes without. The result is always the same. It also makes no difference whether I use Ksmbd or samba4 – both as before.
To test whether there's a hardware defect, I installed an Armbian OS provided by Bananapi (Armbian_23.02.0-trunk_Bananapir2pro_jammy_current_6.1.12.img.xz) on the BPI. And then a Samba server on the Armbian. Data transfer works on all interfaces. So I think the board and its hardware are fine.
Unfortunately, I'm just a user with limited knowledge; I'm more comfortable with the GUI than the CLI.
DDR 2d653b3476 typ 24/01/20-15:04:19,fwver: v1.21
In
LP4/4x derate en, other dram:1x trefi
ddrconfig:0
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
tdqss: cs0 dqs0: 24ps, dqs1: -72ps, dqs2: -24ps, dqs3: -120ps,
change to: 324MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x61
rx vref: 31.9%
tx vref: 38.0%
change to: 528MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
rx vref: 31.9%
tx vref: 38.0%
change to: 780MHz
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
rx vref: 13.4%
tx vref: 38.0%
change to: 1560MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x1c
rx vref: 13.4%
tx vref: 33.0%
cs 0:
the read training result:
DQS0:0x30, DQS1:0x2f, DQS2:0x35, DQS3:0x2d,
min : 0xf 0xf 0x13 0xf 0x1 0x6 0xb 0x8 , 0xc 0x9 0x2 0x3 0xf 0xe 0xe 0xd ,
0x13 0x10 0xd 0xa 0x3 0x1 0x3 0x7 , 0xc 0xb 0x9 0x2 0xe 0x13 0xc 0x11 ,
mid :0x29 0x28 0x2c 0x28 0x1b 0x20 0x24 0x22 ,0x26 0x23 0x1c 0x1d 0x29 0x26 0x27 0x25 ,
0x2f 0x2c 0x27 0x26 0x1f 0x1c 0x1d 0x23 ,0x27 0x24 0x22 0x1c 0x29 0x2b 0x27 0x2a ,
max :0x44 0x42 0x45 0x42 0x36 0x3b 0x3d 0x3c ,0x40 0x3d 0x36 0x37 0x43 0x3e 0x41 0x3e ,
0x4b 0x49 0x42 0x42 0x3b 0x38 0x38 0x3f ,0x42 0x3e 0x3c 0x36 0x44 0x44 0x43 0x44 ,
range:0x35 0x33 0x32 0x33 0x35 0x35 0x32 0x34 ,0x34 0x34 0x34 0x34 0x34 0x30 0x33 0x31 ,
0x38 0x39 0x35 0x38 0x38 0x37 0x35 0x38 ,0x36 0x33 0x33 0x34 0x36 0x31 0x37 0x33 ,
the write training result:
DQS0:0x20, DQS1:0xe, DQS2:0x18, DQS3:0x5,
min :0x6c 0x6d 0x71 0x6c 0x5e 0x62 0x65 0x63 0x64 ,0x54 0x52 0x4c 0x4d 0x58 0x54 0x57 0x54 0x51 ,
0x60 0x5f 0x58 0x57 0x50 0x4f 0x51 0x54 0x57 ,0x4d 0x4b 0x49 0x43 0x4f 0x51 0x4c 0x52 0x49 ,
mid :0x87 0x88 0x8a 0x86 0x76 0x7a 0x7e 0x7c 0x7b ,0x6e 0x6c 0x63 0x65 0x71 0x6c 0x6f 0x6d 0x6a ,
0x7c 0x7a 0x71 0x71 0x6a 0x68 0x69 0x6c 0x6f ,0x66 0x63 0x60 0x5b 0x69 0x6a 0x66 0x6b 0x61 ,
max :0xa2 0xa3 0xa4 0xa1 0x8e 0x93 0x97 0x96 0x93 ,0x88 0x87 0x7b 0x7d 0x8b 0x85 0x87 0x87 0x83 ,
0x98 0x96 0x8b 0x8b 0x84 0x81 0x82 0x85 0x88 ,0x80 0x7c 0x78 0x73 0x84 0x84 0x80 0x85 0x7a ,
range:0x36 0x36 0x33 0x35 0x30 0x31 0x32 0x33 0x2f ,0x34 0x35 0x2f 0x30 0x33 0x31 0x30 0x33 0x32 ,
0x38 0x37 0x33 0x34 0x34 0x32 0x31 0x31 0x31 ,0x33 0x31 0x2f 0x30 0x35 0x33 0x34 0x33 0x31 ,
CA Training result:
cs:0 min :0x3b 0x38 0x33 0x2b 0x2f 0x28 0x3b ,0x3e 0x36 0x32 0x2b 0x2f 0x28 0x37 ,
cs:0 mid :0x79 0x79 0x6f 0x6b 0x6c 0x68 0x65 ,0x7a 0x75 0x6f 0x6a 0x6c 0x67 0x62 ,
cs:0 max :0xb8 0xbb 0xac 0xab 0xaa 0xa8 0x8f ,0xb7 0xb5 0xac 0xa9 0xa9 0xa7 0x8d ,
cs:0 range:0x7d 0x83 0x79 0x80 0x7b 0x80 0x54 ,0x79 0x7f 0x7a 0x7e 0x7a 0x7f 0x56 ,
out
U-Boot SPL 2024.10-OpenWrt-r28427-6df0e3d02a (Feb 03 2025 - 23:09:37 +0000)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
## Checking hash(es) for Image atf-5 ... sha256+ OK
## Checking hash(es) for Image atf-6 ... sha256+ OK
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-645-g8cea6ab0b:cl, fwver: v1.44
NOTICE: BL31: Built : 16:36:43, Sep 19 2023
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid 220114
INFO: l3 cache partition cfg-0
INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2024.10-OpenWrt-r28427-6df0e3d02a (Feb 03 2025 - 23:09:37 +0000)
Model: Bananapi-R2 Pro (RK3568) DDR4 Board
DRAM: 2 GiB
PMIC: RK809 (on=0x40, off=0x00)
Core: 336 devices, 31 uclasses, devicetree: separate
MMC: mmc@fe2b0000: 1, mmc@fe310000: 0
Loading Environment from nowhere... OK
In: serial@fe660000
Out: serial@fe660000
Err: serial@fe660000
Model: Bananapi-R2 Pro (RK3568) DDR4 Board
Net: eth1: ethernet@fe010000, eth0: ethernet@fe2a0000
Hit any key to stop autoboot: 0
Scanning for bootflows in all bootdevs
Seq Method State Uclass Part Name Filename
--- ----------- ------ -------- ---- ------------------------ ----------------
Scanning global bootmeth 'efi_mgr':
Card did not respond to voltage select! : -110
No EFI system partition
No EFI system partition
Failed to persist EFI variables
No EFI system partition
Failed to persist EFI variables
No EFI system partition
Failed to persist EFI variables
0 efi_mgr ready (none) 0 <NULL>
** Booting bootflow '<NULL>' with efi_mgr
Loading Boot0000 'mmc 0' failed
EFI boot manager: Cannot load any image
Boot failed (err=-14)
Scanning bootdev 'mmc@fe2b0000.bootdev':
Card did not respond to voltage select! : -110
Scanning bootdev 'mmc@fe310000.bootdev':
1 script ready mmc 1 mmc@fe310000.bootdev.part /boot.scr
** Booting bootflow 'mmc@fe310000.bootdev.part_1' with script
4540128 bytes read in 109 ms (39.7 MiB/s)
## Loading kernel from FIT Image at 02000000 ...
Using 'config-1' configuration
Verifying Hash Integrity ... OK
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.73
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x020000e8
Data Size: 4476755 Bytes = 4.3 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x03200000
Entry Point: 0x03200000
Hash algo: crc32
Hash value: 5861435d
Hash algo: sha1
Hash value: ad3055f9142bd507f8e20e35a515b98b048118d2
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 02000000 ...
Using 'config-1' configuration
Verifying Hash Integrity ... OK
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt sinovoip_bpi-r2-pro device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x02445180
Data Size: 61461 Bytes = 60 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 5dc59c44
Hash algo: sha1
Hash value: ce6d4c8c9f561badeb2454ee60a42ac7eb645781
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x2445180
Working FDT set to 2445180
Uncompressing Kernel Image to 3200000
Loading Device Tree to 000000007ce9f000, end 000000007ceb1014 ... OK
Working FDT set to 7ce9f000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 6.6.73 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28427-6df0e3d02a) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Feb 3 23:09:37 2025
[ 0.000000] Machine model: Bananapi-R2 Pro (RK3568) DDR4 Board
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000200000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000200000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
[ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
[ 0.000000] cma: Reserved 16 MiB at 0x000000007be00000 on node -1
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 19 pages/cpu s38120 r8192 d31512 u77824
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyS2,1500000 earlycon=uart8250,mmio32,0xfe660000 root=PARTUUID=4aa16d86-02 rw rootwait
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515592
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x000000007d600000-0x000000007d800000] (2MB)
[ 0.000000] Memory: 2018584K/2095104K available (9792K kernel code, 2448K rwdata, 1888K rodata, 2240K init, 741K bss, 60136K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 320 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: MBI range [296:319]
[ 0.000000] GICv3: Using MBI frame 0x00000000fd410000
[ 0.000000] Root IRQ handler: 0xffff800080010088
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 0.000000] ITS: No ITS available, not enabling LPIs
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.001489] Console: colour dummy device 80x25
[ 0.001985] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.003003] pid_max: default: 32768 minimum: 301
[ 0.008364] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.009108] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.014596] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.015806] rcu: Hierarchical SRCU implementation.
[ 0.016282] rcu: Max phase no-delay instances is 1000.
[ 0.018019] smp: Bringing up secondary CPUs ...
[ 0.019309] Detected VIPT I-cache on CPU1
[ 0.019400] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 0.019455] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.020321] Detected VIPT I-cache on CPU2
[ 0.020398] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 0.020440] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 0.021256] Detected VIPT I-cache on CPU3
[ 0.021328] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 0.021367] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 0.021495] smp: Brought up 1 node, 4 CPUs
[ 0.027019] SMP: Total of 4 processors activated.
[ 0.027482] CPU features: detected: 32-bit EL0 Support
[ 0.027985] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.028887] CPU features: detected: Common not Private translations
[ 0.029504] CPU features: detected: CRC32 instructions
[ 0.030010] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.030572] CPU features: detected: Privileged Access Never
[ 0.031116] CPU features: detected: RAS Extension Support
[ 0.031646] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.032437] CPU: All CPU(s) started at EL2
[ 0.032845] alternatives: applying system-wide alternatives
[ 0.049844] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.050834] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.053927] pinctrl core: initialized pinctrl subsystem
[ 0.056590] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.058381] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[ 0.059293] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.060253] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.063169] thermal_sys: Registered thermal governor 'step_wise'
[ 0.063179] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.063825] cpuidle: using governor menu
[ 0.065011] ASID allocator initialised with 65536 entries
[ 0.066196] Serial: AMBA PL011 UART driver
[ 0.079237] /vop@fe040000: Fixed dependency cycle(s) with /hdmi@fe0a0000
[ 0.079990] /hdmi@fe0a0000: Fixed dependency cycle(s) with /vop@fe040000
[ 0.093323] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.094460] rockchip-gpio fdd60000.gpio: probed /pinctrl/gpio@fdd60000
[ 0.095485] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.096581] rockchip-gpio fe740000.gpio: probed /pinctrl/gpio@fe740000
[ 0.097570] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.098660] rockchip-gpio fe750000.gpio: probed /pinctrl/gpio@fe750000
[ 0.099795] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.100883] rockchip-gpio fe760000.gpio: probed /pinctrl/gpio@fe760000
[ 0.101863] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.102933] rockchip-gpio fe770000.gpio: probed /pinctrl/gpio@fe770000
[ 0.108840] /hdmi@fe0a0000: Fixed dependency cycle(s) with /hdmi-con
[ 0.109605] /hdmi-con: Fixed dependency cycle(s) with /hdmi@fe0a0000
[ 0.114775] Modules: 28432 pages in range for non-PLT usage
[ 0.114788] Modules: 519952 pages in range for PLT usage
[ 0.116637] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.117824] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[ 0.118439] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.119100] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
[ 0.119755] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.120419] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.121032] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.121694] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[ 0.124761] cryptd: max_cpu_qlen set to 1000
[ 0.127258] iommu: Default domain type: Passthrough
[ 0.128081] SCSI subsystem initialized
[ 0.128834] usbcore: registered new interface driver usbfs
[ 0.129435] usbcore: registered new interface driver hub
[ 0.130099] usbcore: registered new device driver usb
[ 0.130768] pps_core: LinuxPPS API ver. 1 registered
[ 0.131260] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.132169] PTP clock support registered
[ 0.133128] scmi_core: SCMI protocol bus registered
[ 0.135441] clocksource: Switched to clocksource arch_sys_counter
[ 0.138313] VFS: Disk quotas dquot_6.6.0
[ 0.138873] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.145864] NET: Registered PF_INET protocol family
[ 0.146586] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.151009] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.151875] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.152647] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.153560] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[ 0.154772] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.156071] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear)
[ 0.157005] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.157709] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.159038] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.159639] PCI: CLS 0 bytes, default 64
[ 0.162309] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 0.171087] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.171670] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.178068] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.179125] io scheduler mq-deadline registered
[ 0.475593] phy phy-fe8c0000.phy.7: lane number 0, val 1
[ 0.476137] phy phy-fe8c0000.phy.7: lane number 1, val 2
[ 0.476660] phy phy-fe8c0000.phy.7: bifurcation enabled
[ 0.477294] rockchip-dw-pcie 3c0400000.pcie: host bridge /pcie@fe270000 ranges:
[ 0.478046] rockchip-dw-pcie 3c0400000.pcie: IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[ 0.478922] rockchip-dw-pcie 3c0400000.pcie: MEM 0x00f2200000..0x00f3ffffff -> 0x00f2200000
[ 0.479791] rockchip-dw-pcie 3c0400000.pcie: MEM 0x0340000000..0x037fffffff -> 0x0040000000
[ 0.488991] rockchip-dw-pcie 3c0400000.pcie: iATU: unroll T, 8 ob, 8 ib, align 64K, limit 8G
[ 1.605648] rockchip-dw-pcie 3c0400000.pcie: Phy link never came up
[ 1.606665] rockchip-dw-pcie 3c0400000.pcie: PCI host bridge to bus 0001:00
[ 1.607357] pci_bus 0001:00: root bus resource [bus 00-0f]
[ 1.607903] pci_bus 0001:00: root bus resource [io 0x0000-0xfffff] (bus address [0xf2100000-0xf21fffff])
[ 1.608840] pci_bus 0001:00: root bus resource [mem 0xf2200000-0xf3ffffff]
[ 1.609514] pci_bus 0001:00: root bus resource [mem 0x340000000-0x37fffffff] (bus address [0x40000000-0x7fffffff])
[ 1.610561] pci 0001:00:00.0: [1d87:3566] type 01 class 0x060400
[ 1.611178] pci 0001:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 1.611909] pci 0001:00:00.0: supports D1 D2
[ 1.612334] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 1.618134] pci_bus 0001:01: busn_res: can not insert [bus 01-ff] under [bus 00-0f] (conflicts with (null) [bus 00-0f])
[ 1.619407] pci 0001:00:00.0: BAR 6: assigned [mem 0xf2200000-0xf220ffff pref]
[ 1.620129] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 1.620655] pci_bus 0001:00: resource 4 [io 0x0000-0xfffff]
[ 1.621213] pci_bus 0001:00: resource 5 [mem 0xf2200000-0xf3ffffff]
[ 1.621829] pci_bus 0001:00: resource 6 [mem 0x340000000-0x37fffffff]
[ 1.625094] pcieport 0001:00:00.0: PME: Signaling with IRQ 22
[ 1.626106] pcieport 0001:00:00.0: AER: enabled with IRQ 22
[ 1.695801] rockchip-dw-pcie 3c0800000.pcie: host bridge /pcie@fe280000 ranges:
[ 1.696568] rockchip-dw-pcie 3c0800000.pcie: IO 0x00f0100000..0x00f01fffff -> 0x00f0100000
[ 1.697447] rockchip-dw-pcie 3c0800000.pcie: MEM 0x00f0200000..0x00f1ffffff -> 0x00f0200000
[ 1.698316] rockchip-dw-pcie 3c0800000.pcie: MEM 0x0380000000..0x03bfffffff -> 0x0040000000
[ 1.707634] rockchip-dw-pcie 3c0800000.pcie: iATU: unroll T, 8 ob, 8 ib, align 64K, limit 8G
[ 2.825648] rockchip-dw-pcie 3c0800000.pcie: Phy link never came up
[ 2.826422] rockchip-dw-pcie 3c0800000.pcie: PCI host bridge to bus 0002:00
[ 2.827113] pci_bus 0002:00: root bus resource [bus 00-0f]
[ 2.827658] pci_bus 0002:00: root bus resource [io 0x100000-0x1fffff] (bus address [0xf0100000-0xf01fffff])
[ 2.828620] pci_bus 0002:00: root bus resource [mem 0xf0200000-0xf1ffffff]
[ 2.829296] pci_bus 0002:00: root bus resource [mem 0x380000000-0x3bfffffff] (bus address [0x40000000-0x7fffffff])
[ 2.830343] pci 0002:00:00.0: [1d87:3566] type 01 class 0x060400
[ 2.830950] pci 0002:00:00.0: reg 0x10: [mem 0x00000000-0x3fffffff]
[ 2.831572] pci 0002:00:00.0: reg 0x14: [mem 0x00000000-0x3fffffff]
[ 2.832195] pci 0002:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 2.832927] pci 0002:00:00.0: supports D1 D2
[ 2.833351] pci 0002:00:00.0: PME# supported from D0 D1 D3hot
[ 2.839203] pci_bus 0002:01: busn_res: can not insert [bus 01-ff] under [bus 00-0f] (conflicts with (null) [bus 00-0f])
[ 2.840505] pci 0002:00:00.0: BAR 0: assigned [mem 0x380000000-0x3bfffffff]
[ 2.841203] pci 0002:00:00.0: BAR 1: no space for [mem size 0x40000000]
[ 2.841854] pci 0002:00:00.0: BAR 1: failed to assign [mem size 0x40000000]
[ 2.842541] pci 0002:00:00.0: BAR 6: assigned [mem 0xf0200000-0xf020ffff pref]
[ 2.843258] pci 0002:00:00.0: PCI bridge to [bus 01-ff]
[ 2.843783] pci_bus 0002:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 2.844666] pci_bus 0002:00: resource 4 [io 0x100000-0x1fffff]
[ 2.845250] pci_bus 0002:00: resource 5 [mem 0xf0200000-0xf1ffffff]
[ 2.845894] pci_bus 0002:00: resource 6 [mem 0x380000000-0x3bfffffff]
[ 2.848843] pcieport 0002:00:00.0: PME: Signaling with IRQ 24
[ 2.849853] pcieport 0002:00:00.0: AER: enabled with IRQ 24
[ 2.855148] dma-pl330 fe530000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 2.855983] dma-pl330 fe530000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.859508] dma-pl330 fe550000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 2.860259] dma-pl330 fe550000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.862770] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.869226] printk: console [ttyS2] disabled
[ 2.870036] fe660000.serial: ttyS2 at MMIO 0xfe660000 (irq = 29, base_baud = 1500000) is a 16550A
[ 2.871149] printk: console [ttyS2] enabled
[ 2.871149] printk: console [ttyS2] enabled
[ 2.871935] printk: bootconsole [uart8250] disabled
[ 2.871935] printk: bootconsole [uart8250] disabled
[ 2.878420] random: crng init done
[ 2.884355] loop: module loaded
[ 2.884662] mtip32xx Version 1.3.1
[ 2.890768] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[ 2.891584] rk_gmac-dwmac fe010000.ethernet: supply phy not found, using dummy regulator
[ 2.892445] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
[ 2.893082] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c).
[ 2.893586] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f).
[ 2.894098] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 2.899694] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 2.900469] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 2.901112] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 2.901573] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 2.902233] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 2.902891] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 2.903512] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 2.904081] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 2.904566] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.905271] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10)
[ 2.905935] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 2.906472] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/device width
[ 3.071770] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found
[ 3.072732] rk_gmac-dwmac fe2a0000.ethernet: supply phy not found, using dummy regulator
[ 3.073594] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input).
[ 3.074224] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f).
[ 3.074730] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf).
[ 3.075230] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
[ 3.075852] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY
[ 3.081403] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII
[ 3.082157] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 3.082806] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5
[ 3.083268] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register supported
[ 3.083928] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine supported
[ 3.084587] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
[ 3.085207] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
[ 3.085802] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
[ 3.086292] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.086999] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10)
[ 3.087631] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
[ 3.088163] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/device width
Due to the 32,000 character limit, I had to shorten the boot log at the end.
Thanks in advance
Carsten