Ath79 builds with all kmod packages through opkg [flow offloading]

RelentlesS · November 20, 2018, 8:59am

juppin · November 20, 2018, 6:14pm

ar71xx is also on kernel 4.14
https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/Makefile#L16

RelentlesS · November 21, 2018, 8:06am

Apparently I got a bunch of kern.warn and kern.err in my System Log today.

@juppin Build: 2018/11/17 (4.14.81-1-3f6379f96c9cbdee2d544e6019d873e7)

Model: TP-Link Archer C7 Version 2
Firmware Version: OpenWrt SNAPSHOT r8466-251c350727 / LuCI Master (git-18.321.57475-18c6544)
Kernel Version: 4.14.81

System Log

Wed Nov 21 08:40:19 2018 kern.warn kernel: [170152.389052] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:19 2018 kern.warn kernel: [170152.491456] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170152.593856] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170152.696247] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170152.798648] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170152.901056] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170153.003459] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170153.105865] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170153.208256] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170153.310667] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:20 2018 kern.warn kernel: [170153.413077] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170153.515470] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170153.617878] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170153.720271] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170153.822689] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170153.925087] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170154.027495] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170154.129894] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170154.232283] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170154.334688] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:21 2018 kern.warn kernel: [170154.437093] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170154.539498] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170154.641891] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170154.744281] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170154.846690] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170154.949083] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170155.051480] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170155.153891] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:22 2018 kern.warn kernel: [170155.256276] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.337221] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, attempting to fake crash and restart firmware.
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.348107] ath10k_pci 0000:00:00.0: firmware crashed! (guid 9d2be0d6-4a12-4a74-b511-cc4d59ecd1e7)
Wed Nov 21 08:40:23 2018 kern.info kernel: [170155.357324] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
Wed Nov 21 08:40:23 2018 kern.info kernel: [170155.366789] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Wed Nov 21 08:40:23 2018 kern.info kernel: [170155.379291] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-021-e2174c5 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT crc32 83fdb9cc
Wed Nov 21 08:40:23 2018 kern.info kernel: [170155.406481] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
Wed Nov 21 08:40:23 2018 kern.info kernel: [170155.414001] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.425738] ath10k_pci 0000:00:00.0: firmware register dump:
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.431589] ath10k_pci 0000:00:00.0: [00]: 0x00940750 0x00400C00 0x00980000 0x009B6DCC
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.439724] ath10k_pci 0000:00:00.0: [04]: 0x009B6E3C 0x009B6F60 0x00941B6C 0x00941B20
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.447854] ath10k_pci 0000:00:00.0: [08]: 0x00941B00 0x009423A4 0x009422DC 0x009422C4
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.455973] ath10k_pci 0000:00:00.0: [12]: 0x00941B90 0x009423F4 0x009423D4 0x009423DC
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.464108] ath10k_pci 0000:00:00.0: [16]: 0x009423E4 0x009423EC 0x00942888 0x00942520
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.472240] ath10k_pci 0000:00:00.0: [20]: 0x009424FC 0x0094241C 0x00942540 0x00942498
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.480371] ath10k_pci 0000:00:00.0: [24]: 0x00942450 0x0094250C 0x009424D0 0x00942750
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.488501] ath10k_pci 0000:00:00.0: [28]: 0x00942798 0x00942844 0x009428C4 0x00942594
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.496620] ath10k_pci 0000:00:00.0: [32]: 0x0094258C 0x00942C28 0x00942F4C 0x00942F7C
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.504755] ath10k_pci 0000:00:00.0: [36]: 0x00942F90 0x00942FE4 0x00942FF8 0x00943040
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.512882] ath10k_pci 0000:00:00.0: [40]: 0x0094077C 0x00940790 0x00943084 0x00942F00
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.521017] ath10k_pci 0000:00:00.0: [44]: 0x009B6F8C 0x00942A80 0x00942D40 0x00942D64
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.529155] ath10k_pci 0000:00:00.0: [48]: 0x00942D78 0x00942D9C 0x00957E18 0x00957E28
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.537294] ath10k_pci 0000:00:00.0: [52]: 0x00957E20 0x00940788 0x009430EC 0x00000000
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.545414] ath10k_pci 0000:00:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.553540] ath10k_pci 0000:00:00.0: Copy Engine register dump:
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.559654] ath10k_pci 0000:00:00.0: [00]: 0x00057400  11  11   3   3
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.566285] ath10k_pci 0000:00:00.0: [01]: 0x00057800   8   8 298 299
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.572925] ath10k_pci 0000:00:00.0: [02]: 0x00057c00  24  24  20  24
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.579569] ath10k_pci 0000:00:00.0: [03]: 0x00058000  18  18  18  18
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.586199] ath10k_pci 0000:00:00.0: [04]: 0x00058400 573 573  72  32
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.592839] ath10k_pci 0000:00:00.0: [05]: 0x00058800  27  27 427 443
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.599484] ath10k_pci 0000:00:00.0: [06]: 0x00058c00   2   2   2   2
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.606113] ath10k_pci 0000:00:00.0: [07]: 0x00059000   0   0   0   0
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.614765] ath10k_pci 0000:00:00.0: debug log header, dbuf: 0x4126c0  dropped: 0
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.623472] ath10k_pci 0000:00:00.0: [0] next: 0x4126d8 buf: 0x410524 sz: 1500 len: 280 count: 17 free: 0
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.634296] ath10k_pci 0000:00:00.0: ath10k_pci ATH10K_DBG_BUFFER:
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.640676] ath10k: [0000]: DBB86202 3204FC13 DEDD1091 DBB8620A 83AD620A 28719B00 B1B96202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.649954] ath10k: [0008]: 0A000000 0B000000 C6B96202 204CFC0B 0A000000 0B000000 DAB96202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.659228] ath10k: [0016]: 0A000000 0B000000 EFB96202 204CFC0B 0A000000 0B000000 03BA6202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.668503] ath10k: [0024]: 0A000000 0B000000 18BA6202 204CFC0B 0A000000 0B000000 2CBA6202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.677779] ath10k: [0032]: 0A000000 0B000000 41BA6202 204CFC0B 0A000000 0B000000 55BA6202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.687043] ath10k: [0040]: 0A000000 0B000000 6ABA6202 204CFC0B 0A000000 0B000000 7EBA6202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.696313] ath10k: [0048]: 0A000000 0B000000 93BA6202 204CFC0B 0A000000 0B000000 A7BA6202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.705586] ath10k: [0056]: 0A000000 0B000000 BCBA6202 204CFC0B 0A000000 0B000000 D0BA6202 204CFC0B
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.714861] ath10k: [0064]: 0A000000 0B000000 E5BA6202 204CFC0B 0A000000 0B000000
Wed Nov 21 08:40:23 2018 kern.err kernel: [170155.722545] ath10k_pci 0000:00:00.0: ATH10K_END
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.728257] ath10k_pci 0000:00:00.0: [1] next: 0x4126c0 buf: 0x410b14 sz: 1500 len: 0 count: 0 free: 0
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.762407] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.769964] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.777504] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.785009] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.793728] ath10k_pci 0000:00:00.0: failed to delete peer 38:71:de:13:60:1c for vdev 0: -11
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.802506] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.810399] ath10k_pci 0000:00:00.0: found sta peer 38:71:de:13:60:1c (ptr 86133e00 id 248) entry on vdev 0 after it was supposedly removed
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.828584] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.835115] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 858e3000 vdev: 0 addr: bc:f5:ac:f7:6e:02
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.846360] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 8622f200 vdev: 0 addr: c4:6e:1f:ea:df:f5
Wed Nov 21 08:40:23 2018 kern.info kernel: [170155.990888] ieee80211 phy0: Hardware restart was requested
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170155.996767] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.005018] net_ratelimit: 23 callbacks suppressed
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.005032] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.005041] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.005048] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.373931] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.381301] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.387519] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.393709] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.401085] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.407283] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.413882] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.421280] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:23 2018 kern.warn kernel: [170156.427482] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170156.541174] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170156.548541] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170156.554731] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170157.129861] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170157.137240] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170157.143422] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:24 2018 kern.warn kernel: [170157.152017] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
Wed Nov 21 08:40:24 2018 kern.info kernel: [170157.168898] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
Wed Nov 21 08:40:24 2018 kern.info kernel: [170157.175281] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
Wed Nov 21 08:40:24 2018 kern.info kernel: [170157.183539] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 23868 iram: 26712'
Wed Nov 21 08:40:25 2018 kern.warn kernel: [170158.057274] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
Wed Nov 21 08:40:25 2018 kern.warn kernel: [170158.064622] ath10k_pci 0000:00:00.0: failed to submit frame: -19
Wed Nov 21 08:40:25 2018 kern.warn kernel: [170158.070829] ath10k_pci 0000:00:00.0: failed to push frame: -19
Wed Nov 21 08:40:25 2018 kern.info kernel: [170158.256776] ath10k_pci 0000:00:00.0: device successfully recovered

opkg list-installed

ath10k-firmware-qca988x-ct - 2018-10-10-d366b80d-1
base-files - 196-r8466-251c350727
busybox - 1.29.3-3
dnsmasq - 2.80-1
dropbear - 2017.75-8
firewall - 2018-08-13-1c4d5bcd-2
fstools - 2018-09-29-29e53af0-3
fwtool - 1
hostapd-common - 2018-05-21-62566bc2-6
ip6tables - 1.6.2-3
iptables - 1.6.2-3
iptables-mod-conntrack-extra - 1.6.2-3
iptables-mod-ipopt - 1.6.2-3
iw - 4.14-1
iwinfo - 2018-07-31-65b8333f-1
jshn - 2018-07-25-c83a84af-2
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.14.81-1-3f6379f96c9cbdee2d544e6019d873e7
kmod-ath - 4.14.81+4.19-rc5-1-1
kmod-ath10k-ct - 4.14.81+2018-09-29-b9989fbd-3
kmod-ath9k - 4.14.81+4.19-rc5-1-1
kmod-ath9k-common - 4.14.81+4.19-rc5-1-1
kmod-cfg80211 - 4.14.81+4.19-rc5-1-1
kmod-gpio-button-hotplug - 4.14.81-2
kmod-hwmon-core - 4.14.81-1
kmod-ifb - 4.14.81-1
kmod-ip6tables - 4.14.81-1
kmod-ipt-conntrack - 4.14.81-1
kmod-ipt-conntrack-extra - 4.14.81-1
kmod-ipt-core - 4.14.81-1
kmod-ipt-ipopt - 4.14.81-1
kmod-ipt-nat - 4.14.81-1
kmod-ipt-offload - 4.14.81-1
kmod-ipt-raw - 4.14.81-1
kmod-lib-crc-ccitt - 4.14.81-1
kmod-mac80211 - 4.14.81+4.19-rc5-1-1
kmod-nf-conntrack - 4.14.81-1
kmod-nf-conntrack6 - 4.14.81-1
kmod-nf-flow - 4.14.81-1
kmod-nf-ipt - 4.14.81-1
kmod-nf-ipt6 - 4.14.81-1
kmod-nf-nat - 4.14.81-1
kmod-nf-reject - 4.14.81-1
kmod-nf-reject6 - 4.14.81-1
kmod-nls-base - 4.14.81-1
kmod-phy-ath79-usb - 4.14.81-1
kmod-ppp - 4.14.81-1
kmod-pppoe - 4.14.81-1
kmod-pppox - 4.14.81-1
kmod-sched-cake - 4.14.81+2018-10-02-ddf4c951-1
kmod-sched-core - 4.14.81-1
kmod-slhc - 4.14.81-1
kmod-usb-core - 4.14.81-1
kmod-usb-ehci - 4.14.81-1
kmod-usb-ledtrig-usbport - 4.14.81-1
kmod-usb2 - 4.14.81-1
libblobmsg-json - 2018-07-25-c83a84af-2
libc - 1.1.20-1
libgcc - 7.3.0-1
libip4tc - 1.6.2-3
libip6tc - 1.6.2-3
libiwinfo - 2018-07-31-65b8333f-1
libiwinfo-lua - 2018-07-31-65b8333f-1
libjson-c - 0.12.1-2
libjson-script - 2018-07-25-c83a84af-2
liblua - 5.1.5-1
liblucihttp - 2018-05-18-cb119ded-1
liblucihttp-lua - 2018-05-18-cb119ded-1
libmnl - 1.0.4-1
libnl-tiny - 0.1-5
libpthread - 1.1.20-1
libubox - 2018-07-25-c83a84af-2
libubus - 2018-10-06-221ce7e7-1
libubus-lua - 2018-10-06-221ce7e7-1
libuci - 2018-08-11-4c8b4d6e-1
libuclient - 2018-08-03-ae1c656f-1
libxtables - 1.6.2-3
logd - 2018-02-14-128bc35f-2
lua - 5.1.5-1
luci - git-18.321.57475-18c6544-1
luci-app-firewall - git-18.321.57475-18c6544-1
luci-app-opkg - git-18.321.57475-18c6544-1
luci-app-sqm - 1.2.4-1
luci-base - git-18.321.57475-18c6544-1
luci-lib-ip - git-18.321.57475-18c6544-1
luci-lib-jsonc - git-18.321.57475-18c6544-1
luci-lib-nixio - git-18.321.57475-18c6544-1
luci-mod-admin-full - git-18.321.57475-18c6544-1
luci-mod-network - git-18.321.57475-18c6544-1
luci-mod-status - git-18.321.57475-18c6544-1
luci-mod-system - git-18.321.57475-18c6544-1
luci-proto-ipv6 - git-18.321.57475-18c6544-1
luci-proto-ppp - git-18.321.57475-18c6544-1
luci-theme-bootstrap - git-18.321.57475-18c6544-1
mtd - 23
netifd - 2018-10-17-841b5d15-2
odhcp6c - 2018-07-14-67ae6a71-16
odhcpd-ipv6only - 1.12-3
openwrt-keyring - 2018-05-18-103a32e9-1
opkg - 2017-12-07-3b417b9f-2
ppp - 2.4.7-14
ppp-mod-pppoe - 2.4.7-14
procd - 2018-11-08-20192e47-1
rpcd - 2018-08-16-41333abe-1
rpcd-mod-rrdns - 20170710
sqm-scripts - 1.2.4-1
swconfig - 11
tc - 4.19.0-5
uboot-envtools - 2018.03-2
ubox - 2018-02-14-128bc35f-2
ubus - 2018-10-06-221ce7e7-1
ubusd - 2018-10-06-221ce7e7-1
uci - 2018-08-11-4c8b4d6e-1
uclient-fetch - 2018-08-03-ae1c656f-1
uhttpd - 2018-08-23-b741dec3-1
usign - 2015-07-04-ef641914-1
wireless-regdb - 2017-10-20-4343d359
wpad-basic - 2018-05-21-62566bc2-6

RelentlesS · November 21, 2018, 1:45pm

Kernel Log

[42683.174987] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.277383] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.379794] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.482184] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.584597] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.687001] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.789397] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.891797] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42683.994195] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.096602] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.198994] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.301398] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.403801] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.506197] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.608603] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.711004] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.813399] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42684.915797] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.018200] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.120611] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.222998] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.325409] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.427795] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.530210] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.632608] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.735006] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.837417] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.939807] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42685.997237] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, attempting to fake crash and restart firmware.
[42686.008205] ath10k_pci 0000:00:00.0: firmware crashed! (guid 4d1563e2-81df-40ee-ad40-eba24dd7a3b0)
[42686.017370] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[42686.026740] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[42686.039161] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-021-e2174c5 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT crc32 83fdb9cc
[42686.066279] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[42686.073714] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[42686.085377] ath10k_pci 0000:00:00.0: firmware register dump:
[42686.091147] ath10k_pci 0000:00:00.0: [00]: 0x00940750 0x00400C00 0x00980000 0x009B6DCC
[42686.099192] ath10k_pci 0000:00:00.0: [04]: 0x009B6E3C 0x009B6F60 0x00941B6C 0x00941B20
[42686.107242] ath10k_pci 0000:00:00.0: [08]: 0x00941B00 0x009423A4 0x009422DC 0x009422C4
[42686.115271] ath10k_pci 0000:00:00.0: [12]: 0x00941B90 0x009423F4 0x009423D4 0x009423DC
[42686.123319] ath10k_pci 0000:00:00.0: [16]: 0x009423E4 0x009423EC 0x00942888 0x00942520
[42686.131370] ath10k_pci 0000:00:00.0: [20]: 0x009424FC 0x0094241C 0x00942540 0x00942498
[42686.139410] ath10k_pci 0000:00:00.0: [24]: 0x00942450 0x0094250C 0x009424D0 0x00942750
[42686.147464] ath10k_pci 0000:00:00.0: [28]: 0x00942798 0x00942844 0x009428C4 0x00942594
[42686.155502] ath10k_pci 0000:00:00.0: [32]: 0x0094258C 0x00942C28 0x00942F4C 0x00942F7C
[42686.163545] ath10k_pci 0000:00:00.0: [36]: 0x00942F90 0x00942FE4 0x00942FF8 0x00943040
[42686.171599] ath10k_pci 0000:00:00.0: [40]: 0x0094077C 0x00940790 0x00943084 0x00942F00
[42686.179642] ath10k_pci 0000:00:00.0: [44]: 0x009B6F8C 0x00942A80 0x00942D40 0x00942D64
[42686.187683] ath10k_pci 0000:00:00.0: [48]: 0x00942D78 0x00942D9C 0x00957E18 0x00957E28
[42686.195718] ath10k_pci 0000:00:00.0: [52]: 0x00957E20 0x00940788 0x009430EC 0x00000000
[42686.203761] ath10k_pci 0000:00:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
[42686.211807] ath10k_pci 0000:00:00.0: Copy Engine register dump:
[42686.217833] ath10k_pci 0000:00:00.0: [00]: 0x00057400  11  11   3   3
[42686.224376] ath10k_pci 0000:00:00.0: [01]: 0x00057800  26  26 412 413
[42686.230933] ath10k_pci 0000:00:00.0: [02]: 0x00057c00  63  63  59  63
[42686.237488] ath10k_pci 0000:00:00.0: [03]: 0x00058000  21  21  21  21
[42686.244029] ath10k_pci 0000:00:00.0: [04]: 0x00058400 7739 7739  71  31
[42686.250766] ath10k_pci 0000:00:00.0: [05]: 0x00058800  31  31 217 223
[42686.257317] ath10k_pci 0000:00:00.0: [06]: 0x00058c00  14  14  14  14
[42686.263861] ath10k_pci 0000:00:00.0: [07]: 0x00059000   0   0   0   0
[42686.272437] ath10k_pci 0000:00:00.0: debug log header, dbuf: 0x4126c0  dropped: 0
[42686.281055] ath10k_pci 0000:00:00.0: [0] next: 0x4126d8 buf: 0x410524 sz: 1500 len: 688 count: 43 free: 0
[42686.291810] ath10k_pci 0000:00:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[42686.298109] ath10k: [0000]: 410D9B02 E84F0008 00020301 00000000 410D9B02 E84F0008 00000300 00000000
[42686.307304] ath10k: [0008]: 410D9B02 E84F0008 00020301 06000000 410D9B02 E84F0008 00000300 06000000
[42686.316482] ath10k: [0016]: 410D9B02 E84F0008 00020301 11000000 410D9B02 E84F0008 00000300 11000000
[42686.325675] ath10k: [0024]: 410D9B02 204CFC0B 0A000000 0B000000 420D9B02 E86B0008 00000401 00000200
[42686.334870] ath10k: [0032]: 420D9B02 E86B0008 00020400 01000200 420D9B02 E86B0008 00010201 01000200
[42686.344069] ath10k: [0040]: 420D9B02 E86B0008 00030200 01000200 420D9B02 E86B0008 00030301 01000200
[42686.353255] ath10k: [0048]: 420D9B02 E86B0008 00040300 00000200 560D9B02 204CFC0B 0A000000 0B000000
[42686.362441] ath10k: [0056]: 6A0D9B02 204CFC0B 0A000000 0B000000 6F0D9B02 E84F0008 00010001 00000000
[42686.371628] ath10k: [0064]: 6F0D9B02 E84F0008 00030000 00000000 6F0D9B02 E84F0008 00010001 06000000
[42686.380815] ath10k: [0072]: 6F0D9B02 E84F0008 00030000 06000000 6F0D9B02 E84F0008 00010001 11000000
[42686.390003] ath10k: [0080]: 6F0D9B02 E84F0008 00030000 11000000 7F0D9B02 204CFC0B 0A000000 0B000000
[42686.399184] ath10k: [0088]: 930D9B02 204CFC0B 0A000000 0B000000 A80D9B02 204CFC0B 0A000000 0B000000
[42686.408368] ath10k: [0096]: BC0D9B02 204CFC0B 0A000000 0B000000 D10D9B02 204CFC0B 0A000000 0B000000
[42686.417555] ath10k: [0104]: E50D9B02 204CFC0B 0A000000 0B000000 F30D9B02 E84F0008 00020301 00000000
[42686.426730] ath10k: [0112]: F30D9B02 E84F0008 00000300 00000000 F30D9B02 E84F0008 00020301 06000000
[42686.435912] ath10k: [0120]: F30D9B02 E84F0008 00000300 06000000 F30D9B02 E84F0008 00020301 11000000
[42686.445099] ath10k: [0128]: F30D9B02 E84F0008 00000300 11000000 FA0D9B02 204CFC0B 0A000000 0B000000
[42686.454285] ath10k: [0136]: 0E0E9B02 204CFC0B 0A000000 0B000000 210E9B02 E84F0008 00010001 00000000
[42686.463472] ath10k: [0144]: 210E9B02 E84F0008 00030000 00000000 210E9B02 E84F0008 00010001 06000000
[42686.472661] ath10k: [0152]: 210E9B02 E84F0008 00030000 06000000 210E9B02 E84F0008 00010001 11000000
[42686.481848] ath10k: [0160]: 210E9B02 E84F0008 00030000 11000000 230E9B02 204CFC0B 0A000000 0B000000
[42686.491032] ath10k: [0168]: 370E9B02 204CFC0B 0A000000 0B000000
[42686.497038] ath10k_pci 0000:00:00.0: ATH10K_END
[42686.502663] ath10k_pci 0000:00:00.0: [1] next: 0x4126c0 buf: 0x410b14 sz: 1500 len: 0 count: 0 free: 0
[42686.536970] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.544442] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.551888] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.559327] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.566765] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.575063] ath10k_pci 0000:00:00.0: failed to delete peer 40:4e:36:1b:64:18 for vdev 0: -11
[42686.583766] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.592434] ath10k_pci 0000:00:00.0: found sta peer 40:4e:36:1b:64:18 (ptr 8622fa00 id 249) entry on vdev 0 after it was supposedly removed
[42686.605599] ------------[ cut here ]------------
[42686.610461] WARNING: CPU: 0 PID: 2862 at backports-4.19-rc5-1/net/mac80211/sta_info.c:1004 sta_set_sinfo+0xaec/0xb98 [mac80211]
[42686.622231] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables crc_ccitt compat sch_cake nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex
[42686.694678] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.702349]  cls_flow cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress ledtrig_usbport ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables ifb ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[42686.727013] CPU: 0 PID: 2862 Comm: hostapd Not tainted 4.14.81 #0
[42686.733502] Stack : 80540000 804fdb04 00000000 00000000 804d3050 870e5b04 87ee2edc 80529987
[42686.742049]         804cf460 00000b2e 80683670 000003ec 870e5cb4 00000001 870e5ab8 dc641f23
[42686.750892]         00000000 00000000 80680000 00009470 00000000 00000000 00000008 00000000
[42686.759485] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.766934]         00000192 57f6cfa4 00000191 00000000 80000000 00000000 877639e8 877079a4
[42686.775929]         00000009 000003ec 870e5cb4 87cd6000 00000000 80273c04 00000000 80680000
[42686.784766]         ...
[42686.787286] Call Trace:
[42686.789809] [<8006a92c>] show_stack+0x58/0x100
[42686.794338] [<800809a0>] __warn+0xe4/0x118
[42686.798729] [<80080a64>] warn_slowpath_null+0x1c/0x28
[42686.803984] [<877079a4>] sta_set_sinfo+0xaec/0xb98 [mac80211]
[42686.809972] [<87707b30>] sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
[42686.816771] [<8768f100>] cfg80211_check_station_change+0x1be4/0x2c58 [cfg80211]
[42686.824345] ---[ end trace 5376ce152cbaf3fa ]---
[42686.837335] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
[42686.843558] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 8673e200 vdev: 0 addr: 38:de:ad:69:13:b0 
[42686.854707] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 84cfc000 vdev: 0 addr: 38:71:de:13:60:1c 
[42686.865838] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 86721800 vdev: 0 addr: a4:34:d9:e9:e0:67 
[42686.876968] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 87067c00 vdev: 0 addr: c4:6e:1f:ea:df:f5 
[42686.888299] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42686.896247] ath10k_pci 0000:00:00.0: Invalid state: 2 in ath10k_htt_tx_32, warning will not be repeated.
[42686.905923] ------------[ cut here ]------------
[42686.910689] WARNING: CPU: 0 PID: 1397 at /home/johann/dev/openwrt/openwrt/build_dir/target-mips_24kc_musl/linux-ath79_generic/ath10k-ct-2018-09-29-b9989fbd/ath10k-4.16/htt_tx.c:1250 ath10k_convert_hw_rate_to_rate_info+0x178/0x9ec [ath10k_core]
[42686.932552] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables crc_ccitt compat sch_cake nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex
[42687.004965]  cls_flow cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress ledtrig_usbport ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables ifb ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[42687.029358] CPU: 0 PID: 1397 Comm: kworker/u2:3 Tainted: G        W       4.14.81 #0
[42687.037247] Workqueue: ath10k_wq ath10k_core_create [ath10k_core]
[42687.043433] Stack : 00000009 000004e2 87db0468 800ae0d4 804d3050 87053674 87da4ddc 80529987
[42687.051938]         804cf3cc 8705364c 80520000 800aef34 87db0468 00000000 87053628 922e8c0d
[42687.060438]         00000000 00000000 00000000 0000a328 00000000 00000000 00000008 00000000
[42687.068929]         000001ae 80530000 000001ad 00000000 00000000 00000000 877cc1ac 877a2978
[42687.077427]         00000009 000004e2 87db0468 85004134 00000000 80273c04 00000000 80680000
[42687.085911]         ...
[42687.088406] Call Trace:
[42687.090912] [<8006a92c>] show_stack+0x58/0x100
[42687.095437] [<800809a0>] __warn+0xe4/0x118
[42687.099614] [<80080a64>] warn_slowpath_null+0x1c/0x28
[42687.104772] [<877a2978>] ath10k_convert_hw_rate_to_rate_info+0x178/0x9ec [ath10k_core]
[42687.112843] [<8778475c>] 0x8778475c
[42687.116399] ---[ end trace 5376ce152cbaf3fb ]---
[42687.121103] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.128362] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.134450] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.141729] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42687.149213] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42687.156950] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.164257] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.170388] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.176378] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.183648] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.189755] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.195738] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.203007] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.209110] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.215091] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.222357] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.228460] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.236565] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[42687.244175] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.251458] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.257563] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.263576] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.270847] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.276938] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.282965] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped new beacon
[42687.290599] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.297870] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.303963] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.311440] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.318728] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.324837] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.331000] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[42687.338288] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.344385] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.355961] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.362134] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.372509] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.378676] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.385792] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.391968] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.399119] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.405254] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.525222] ieee80211 phy0: Hardware restart was requested
[42687.532119] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
[42687.572330] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.578463] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.589772] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.595883] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.713044] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.719194] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.725304] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.731456] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42687.822978] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42687.829111] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.191235] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.197365] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.326755] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.332897] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.415599] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.421742] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.453447] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.459588] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.653498] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.659629] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.665830] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.671967] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.679160] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.685263] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.691969] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.698127] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.704423] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.710569] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.717236] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.723335] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.729877] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42688.735992] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42688.742553] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[42688.759360] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[42688.765659] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[42688.773829] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[42689.111976] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42689.118122] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42689.244113] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42689.250251] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42689.338869] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[42689.344995] ath10k_pci 0000:00:00.0: failed to push frame: -19
[42689.848238] ath10k_pci 0000:00:00.0: device successfully recovered
[170152.389052] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170152.491456] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170152.593856] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170152.696247] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170152.798648] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170152.901056] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.003459] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.105865] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.208256] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.310667] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.413077] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.515470] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.617878] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.720271] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.822689] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170153.925087] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.027495] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.129894] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.232283] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.334688] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.437093] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.539498] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.641891] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.744281] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.846690] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170154.949083] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.051480] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.153891] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.256276] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.337221] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, attempting to fake crash and restart firmware.
[170155.348107] ath10k_pci 0000:00:00.0: firmware crashed! (guid 9d2be0d6-4a12-4a74-b511-cc4d59ecd1e7)
[170155.357324] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[170155.366789] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[170155.379291] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-021-e2174c5 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT crc32 83fdb9cc
[170155.406481] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[170155.414001] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[170155.425738] ath10k_pci 0000:00:00.0: firmware register dump:
[170155.431589] ath10k_pci 0000:00:00.0: [00]: 0x00940750 0x00400C00 0x00980000 0x009B6DCC
[170155.439724] ath10k_pci 0000:00:00.0: [04]: 0x009B6E3C 0x009B6F60 0x00941B6C 0x00941B20
[170155.447854] ath10k_pci 0000:00:00.0: [08]: 0x00941B00 0x009423A4 0x009422DC 0x009422C4
[170155.455973] ath10k_pci 0000:00:00.0: [12]: 0x00941B90 0x009423F4 0x009423D4 0x009423DC
[170155.464108] ath10k_pci 0000:00:00.0: [16]: 0x009423E4 0x009423EC 0x00942888 0x00942520
[170155.472240] ath10k_pci 0000:00:00.0: [20]: 0x009424FC 0x0094241C 0x00942540 0x00942498
[170155.480371] ath10k_pci 0000:00:00.0: [24]: 0x00942450 0x0094250C 0x009424D0 0x00942750
[170155.488501] ath10k_pci 0000:00:00.0: [28]: 0x00942798 0x00942844 0x009428C4 0x00942594
[170155.496620] ath10k_pci 0000:00:00.0: [32]: 0x0094258C 0x00942C28 0x00942F4C 0x00942F7C
[170155.504755] ath10k_pci 0000:00:00.0: [36]: 0x00942F90 0x00942FE4 0x00942FF8 0x00943040
[170155.512882] ath10k_pci 0000:00:00.0: [40]: 0x0094077C 0x00940790 0x00943084 0x00942F00
[170155.521017] ath10k_pci 0000:00:00.0: [44]: 0x009B6F8C 0x00942A80 0x00942D40 0x00942D64
[170155.529155] ath10k_pci 0000:00:00.0: [48]: 0x00942D78 0x00942D9C 0x00957E18 0x00957E28
[170155.537294] ath10k_pci 0000:00:00.0: [52]: 0x00957E20 0x00940788 0x009430EC 0x00000000
[170155.545414] ath10k_pci 0000:00:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000
[170155.553540] ath10k_pci 0000:00:00.0: Copy Engine register dump:
[170155.559654] ath10k_pci 0000:00:00.0: [00]: 0x00057400  11  11   3   3
[170155.566285] ath10k_pci 0000:00:00.0: [01]: 0x00057800   8   8 298 299
[170155.572925] ath10k_pci 0000:00:00.0: [02]: 0x00057c00  24  24  20  24
[170155.579569] ath10k_pci 0000:00:00.0: [03]: 0x00058000  18  18  18  18
[170155.586199] ath10k_pci 0000:00:00.0: [04]: 0x00058400 573 573  72  32
[170155.592839] ath10k_pci 0000:00:00.0: [05]: 0x00058800  27  27 427 443
[170155.599484] ath10k_pci 0000:00:00.0: [06]: 0x00058c00   2   2   2   2
[170155.606113] ath10k_pci 0000:00:00.0: [07]: 0x00059000   0   0   0   0
[170155.614765] ath10k_pci 0000:00:00.0: debug log header, dbuf: 0x4126c0  dropped: 0
[170155.623472] ath10k_pci 0000:00:00.0: [0] next: 0x4126d8 buf: 0x410524 sz: 1500 len: 280 count: 17 free: 0
[170155.634296] ath10k_pci 0000:00:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[170155.640676] ath10k: [0000]: DBB86202 3204FC13 DEDD1091 DBB8620A 83AD620A 28719B00 B1B96202 204CFC0B
[170155.649954] ath10k: [0008]: 0A000000 0B000000 C6B96202 204CFC0B 0A000000 0B000000 DAB96202 204CFC0B
[170155.659228] ath10k: [0016]: 0A000000 0B000000 EFB96202 204CFC0B 0A000000 0B000000 03BA6202 204CFC0B
[170155.668503] ath10k: [0024]: 0A000000 0B000000 18BA6202 204CFC0B 0A000000 0B000000 2CBA6202 204CFC0B
[170155.677779] ath10k: [0032]: 0A000000 0B000000 41BA6202 204CFC0B 0A000000 0B000000 55BA6202 204CFC0B
[170155.687043] ath10k: [0040]: 0A000000 0B000000 6ABA6202 204CFC0B 0A000000 0B000000 7EBA6202 204CFC0B
[170155.696313] ath10k: [0048]: 0A000000 0B000000 93BA6202 204CFC0B 0A000000 0B000000 A7BA6202 204CFC0B
[170155.705586] ath10k: [0056]: 0A000000 0B000000 BCBA6202 204CFC0B 0A000000 0B000000 D0BA6202 204CFC0B
[170155.714861] ath10k: [0064]: 0A000000 0B000000 E5BA6202 204CFC0B 0A000000 0B000000
[170155.722545] ath10k_pci 0000:00:00.0: ATH10K_END
[170155.728257] ath10k_pci 0000:00:00.0: [1] next: 0x4126c0 buf: 0x410b14 sz: 1500 len: 0 count: 0 free: 0
[170155.762407] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.769964] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.777504] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.785009] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.793728] ath10k_pci 0000:00:00.0: failed to delete peer 38:71:de:13:60:1c for vdev 0: -11
[170155.802506] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[170155.810399] ath10k_pci 0000:00:00.0: found sta peer 38:71:de:13:60:1c (ptr 86133e00 id 248) entry on vdev 0 after it was supposedly removed
[170155.828584] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
[170155.835115] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 858e3000 vdev: 0 addr: bc:f5:ac:f7:6e:02 
[170155.846360] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 8622f200 vdev: 0 addr: c4:6e:1f:ea:df:f5 
[170155.990888] ieee80211 phy0: Hardware restart was requested
[170155.996767] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
[170156.005018] net_ratelimit: 23 callbacks suppressed
[170156.005032] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170156.005041] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170156.005048] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170156.373931] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170156.381301] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170156.387519] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170156.393709] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170156.401085] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170156.407283] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170156.413882] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170156.421280] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170156.427482] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170156.541174] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170156.548541] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170156.554731] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170157.129861] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170157.137240] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170157.143422] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170157.152017] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[170157.168898] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[170157.175281] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[170157.183539] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[170158.057274] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[170158.064622] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[170158.070829] ath10k_pci 0000:00:00.0: failed to push frame: -19
[170158.256776] ath10k_pci 0000:00:00.0: device successfully recovered

Note that I flashed this build on Mon Nov 19 an the error occurred on Wed Nov 21

juppin · November 21, 2018, 4:03pm

Did you tested also ar71xx snapshots? If not, can you test if this error occurs also on this target?

Enig123 · November 21, 2018, 5:33pm

There're no such error messages found with previous 4.14.80 kernel on which I am still lying.

juppin · November 21, 2018, 9:34pm

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.81&id=ef5d27e1ed9c97c0670d0aa1f433f68e29de5bfb

Here is a commit related to this problem... But i think this should solve a problem that exists for some time...
I´ll take a look at this tomorrow but i don´t have a device with ath10 for testing.

Probably this error exist also on 4.14.80!?

Could you post a complete kernel boot log?
The part where the firmware get loaded is important.

Enig123 · November 21, 2018, 10:59pm

Kernel Logs are as following:

Kernel Logs

[ 0.000000] Linux version 4.14.80 (johann@johann-nb) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8438-c97c672f9b)) #0 Mon Nov 12 22:44:01 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link Archer C7 Version 2
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 80547a40, node_mem_map 81008da0
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x47c with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=132768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 122984K/131072K available (3929K kernel code, 158K rwdata, 940K rodata, 1236K init, 211K bss, 8088K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 720.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008298] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.074985] pid_max: default: 32768 minimum: 301
[ 0.080069] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.087104] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.098251] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.108743] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.115299] pinctrl core: initialized pinctrl subsystem
[ 0.122661] NET: Registered protocol family 16
[ 0.133200] PCI host bridge /ahb/apb/pcie-controller@18250000 ranges:
[ 0.140065] MEM 0x0000000012000000..0x0000000013ffffff
[ 0.145653] IO 0x0000000000000000..0x0000000000000000
[ 0.165410] PCI host bridge to bus 0000:00
[ 0.169809] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.177115] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.183050] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.190270] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.198733] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 0.198787] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.198842] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.198915] pci 0000:00:00.0: supports D1 D2
[ 0.199083] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.199106] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.206896] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.216740] clocksource: Switched to clocksource MIPS
[ 0.222917] NET: Registered protocol family 2
[ 0.228296] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.235721] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.242525] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.249404] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.255622] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.262525] NET: Registered protocol family 1
[ 0.267220] PCI: CLS 0 bytes, default 32
[ 0.269475] Crashlog allocated RAM at address 0x3f00000
[ 0.276017] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.287026] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.293224] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.310857] io scheduler noop registered
[ 0.315032] io scheduler deadline registered (default)
[ 0.320821] ar7200-usb-phy ahb:apb:usb-phy0: phy reset is missing
[ 0.327381] ar7200-usb-phy ahb:apb:usb-phy1: phy reset is missing
[ 0.335438] pinctrl-single 1804002c.pinmux: 512 pins at pa b804002c size 64
[ 0.343370] gpio-export gpio-export: 2 gpio(s) exported
[ 0.349707] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.358498] console [ttyS0] disabled
[ 0.362331] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 2500000) is a 16550A
[ 0.371542] console [ttyS0] enabled
[ 0.378961] bootconsole [early0] disabled
[ 0.405505] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.410346] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.416803] Creating 3 MTD partitions on "spi0.0":
[ 0.421662] 0x000000000000-0x000000020000 : "u-boot"
[ 0.427355] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.483928] 2 tplink-fw partitions found on MTD device firmware
[ 0.489963] 0x000000020000-0x0000001b9e3d : "kernel"
[ 0.495602] 0x0000001b9e40-0x000000ff0000 : "rootfs"
[ 0.501250] mtd: device 3 (rootfs) set to be root filesystem
[ 0.507064] 1 squashfs-split partitions found on MTD device rootfs
[ 0.513332] 0x000000480000-0x000000ff0000 : "rootfs_data"
[ 0.519428] 0x000000ff0000-0x000001000000 : "art"
[ 0.525742] libphy: Fixed MDIO Bus: probed
[ 0.867099] libphy: ag71xx_mdio: probed
[ 0.873508] switch0: Atheros AR8327 rev. 4 switch registered on mdio-bus.0
[ 1.857907] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 1.869288] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.208322] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 2.217939] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 2.226175] NET: Registered protocol family 10
[ 2.234634] Segment Routing with IPv6
[ 2.238479] NET: Registered protocol family 17
[ 2.243019] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.256171] 8021q: 802.1Q VLAN Support v1.8
[ 2.268595] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.280176] Freeing unused kernel memory: 1236K
[ 2.284773] This architecture does not have kernel memory protection.
[ 2.566757] random: fast init done
[ 2.998250] init: Console is alive
[ 3.001863] init: - watchdog -
[ 4.165183] kmodloader: loading kernel modules from /etc/modules-boot.d/
[ 4.302719] usbcore: registered new interface driver usbfs
[ 4.308391] usbcore: registered new interface driver hub
[ 4.313866] usbcore: registered new device driver usb
[ 4.323909] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.331913] ehci-platform: EHCI generic platform driver
[ 4.337476] ehci-platform 1b000000.usb: EHCI Host Controller
[ 4.343264] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 4.351295] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 4.386761] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 4.393719] hub 1-0:1.0: USB hub found
[ 4.397840] hub 1-0:1.0: 1 port detected
[ 4.402327] ehci-platform 1b400000.usb: EHCI Host Controller
[ 4.408144] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[ 4.416165] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
[ 4.446763] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[ 4.453750] hub 2-0:1.0: USB hub found
[ 4.457868] hub 2-0:1.0: 1 port detected
[ 4.462785] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.480496] init: - preinit -
[ 5.717834] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.956129] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.119408] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.371400] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 7.377425] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 7.421122] urandom_read: 4 callbacks suppressed
[ 7.421129] random: procd: uninitialized urandom read (4 bytes read)
[ 8.437877] eth1: link up (1000Mbps/Full duplex)
[ 8.442585] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 8.450981] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
[ 10.605266] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 10.612642] jffs2_build_filesystem(): unlocking the mtd device...
[ 10.612711] done.
[ 10.620942] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 55.930830] done.
[ 55.940419] jffs2: notice: (482) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 55.957334] mount_root: overlay filesystem has not been fully initialized yet
[ 55.976887] mount_root: switching to jffs2 overlay
[ 56.002732] overlayfs: upper fs does not support tmpfile.
[ 56.502765] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 56.612983] procd: - early -
[ 56.615976] procd: - watchdog -
[ 57.178212] procd: - watchdog -
[ 57.181609] procd: - ubus -
[ 57.236260] random: ubusd: uninitialized urandom read (4 bytes read)
[ 57.243548] random: ubusd: uninitialized urandom read (4 bytes read)
[ 57.251180] procd: - init -
[ 57.445134] eth1: link down
[ 57.587084] kmodloader: loading kernel modules from /etc/modules.d/*
[ 57.597549] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 57.613758] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85
[ 57.621559] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
[ 57.630847] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 57.649527] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 57.704022] xt_time: kernel timezone is -0000
[ 57.755911] PPP generic driver version 2.4.2
[ 57.762331] NET: Registered protocol family 24
[ 57.789224] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 57.798408] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 57.806357] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 58.080120] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
[ 58.090823] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 58.228786] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[ 58.237961] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[ 58.248837] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 58.414857] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 58.424210] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[ 58.434737] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 65.029762] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[ 65.040914] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 65.167495] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 65.177148] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[ 65.188299] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 65.353489] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 65.363115] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 65.373994] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 65.539895] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 65.549248] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[ 65.560123] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 65.725927] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[ 65.735282] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[ 65.746164] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 65.912118] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[ 65.921471] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[ 65.932353] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 66.104069] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[ 66.119027] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 66.128422] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 66.140817] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-021-e2174c5 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT crc32 83fdb9cc
[ 66.256910] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 66.267524] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 66.360925] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 66.370174] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 67.305034] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 67.322474] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 67.328802] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 67.336955] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[ 67.404957] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 67.549594] ath: EEPROM regdomain: 0x0
[ 67.549599] ath: EEPROM indicates default country code should be used
[ 67.549602] ath: doing EEPROM country->regdmn map search
[ 67.549615] ath: country maps to regdmn code: 0x3a
[ 67.549620] ath: Country alpha2 being used: US
[ 67.549623] ath: Regpair used: 0x3a
[ 67.609775] ath: EEPROM regdomain: 0x0
[ 67.609781] ath: EEPROM indicates default country code should be used
[ 67.609785] ath: doing EEPROM country->regdmn map search
[ 67.609797] ath: country maps to regdmn code: 0x3a
[ 67.609802] ath: Country alpha2 being used: US
[ 67.609805] ath: Regpair used: 0x3a
[ 67.627663] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 67.629137] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=12
[ 67.692275] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 75.832757] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 75.839873] eth1: link up (1000Mbps/Full duplex)
[ 75.844572] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 75.869236] br-lan: port 1(eth1.1) entered blocking state
[ 75.874721] br-lan: port 1(eth1.1) entered disabled state
[ 75.880592] device eth1.1 entered promiscuous mode
[ 75.885454] device eth1 entered promiscuous mode
[ 75.899010] br-lan: port 1(eth1.1) entered blocking state
[ 75.904493] br-lan: port 1(eth1.1) entered forwarding state
[ 75.910390] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 75.988831] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 76.006305] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 76.025643] IPv6: ADDRCONF(NETDEV_UP): br-guest: link is not ready
[ 76.836923] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 77.079778] eth0: link up (1000Mbps/Full duplex)
[ 77.100344] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 77.236866] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 80.714278] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 80.814942] br-guest: port 1(wlan1) entered blocking state
[ 80.820598] br-guest: port 1(wlan1) entered disabled state
[ 80.826488] device wlan1 entered promiscuous mode
[ 80.831675] br-guest: port 1(wlan1) entered blocking state
[ 80.837275] br-guest: port 1(wlan1) entered forwarding state
[ 82.957828] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 82.975256] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 82.981630] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 82.989792] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[ 83.100798] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 83.109026] br-guest: port 1(wlan1) entered disabled state
[ 83.200473] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 83.207143] br-guest: port 1(wlan1) entered blocking state
[ 83.212706] br-guest: port 1(wlan1) entered forwarding state
[ 83.222486] br-guest: port 2(wlan0) entered blocking state
[ 83.228107] br-guest: port 2(wlan0) entered disabled state
[ 83.233946] device wlan0 entered promiscuous mode
[ 83.287600] IPv6: ADDRCONF(NETDEV_CHANGE): br-guest: link becomes ready
[ 83.943977] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 84.394551] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 84.401192] br-guest: port 2(wlan0) entered blocking state
[ 84.406791] br-guest: port 2(wlan0) entered forwarding state
[ 96.131823] random: crng init done

RelentlesS · November 22, 2018, 7:37am

Entire Kernel Log of 4.14.81 ath79 Build (Ubuntu Pastebin Link due to character limit of this forum. 1Month available)

The commit you mentioned seems related to me.. especially the

The issue is hard to reproduce and shows up once in a few days [...]
This implies a connectivity outage of about 1.4s in AP mode, but brings back the interface and the whole system to a usable state.

paragraph of the commit message.

I'm going to test
archer-c7-v2-squashfs-factory.bin a4c40c79f9b80f37dcf3eeab4af033ab4cfc0a01dcc4b2ab52999ec917c35dbd 15872.0 KB Wed Nov 21 16:42:24 2018
snapshot build now.

RelentlesS · November 22, 2018, 8:33am

No errors up until now. I'll update you if errors show up in the comming days.

Kernel Log 4.14.81 ar71xx Snapshot from Wed Nov 21

[    0.000000] Linux version 4.14.81 (buildbot@slashdirt-03) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8474-0191a06)) #0 Wed Nov 21 14:15:05 2018
[    0.000000] MyLoader: sysp=02000000, boardp=00000000, parts=00000000
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 8053c910, node_mem_map 81000020
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x47c with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=ARCHER-C7-V2  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 123976K/131072K available (3865K kernel code, 190K rwdata, 924K rodata, 324K init, 211K bss, 7096K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008293] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.074984] pid_max: default: 32768 minimum: 301
[    0.080074] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.087114] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.096385] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.106877] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.114305] NET: Registered protocol family 16
[    0.120148] MIPS: machine is TP-LINK Archer C7
[    0.127931] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.133431] registering PCI controller with io_map_base unset
[    0.139665] registering PCI controller with io_map_base unset
[    0.639169] PCI host bridge to bus 0000:00
[    0.643532] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.650878] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.656806] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.664031] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.672468] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.672566] PCI host bridge to bus 0000:01
[    0.676946] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[    0.684256] pci_bus 0000:01: root bus resource [io  0x0001]
[    0.690187] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.697402] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.705857] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
[    0.705912] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.705966] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    0.706038] pci 0000:01:00.0: supports D1 D2
[    0.706204] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.706225] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.714019] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[    0.724477] clocksource: Switched to clocksource MIPS
[    0.730690] NET: Registered protocol family 2
[    0.736070] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.743491] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750295] TCP: Hash tables configured (established 1024 bind 1024)
[    0.757171] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.763394] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.770282] NET: Registered protocol family 1
[    0.774980] PCI: CLS 0 bytes, default 32
[    0.777296] Crashlog allocated RAM at address 0x3f00000
[    0.783853] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.794950] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.801155] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.819003] io scheduler noop registered
[    0.823172] io scheduler deadline registered (default)
[    0.829022] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.837513] console [ttyS0] disabled
[    0.861395] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.870578] console [ttyS0] enabled
[    0.877996] bootconsole [early0] disabled
[    0.891811] m25p80 spi0.0: found s25fl128s, expected m25p80
[    0.897548] m25p80 spi0.0: s25fl128s (16384 Kbytes)
[    0.903448] 5 tp-link partitions found on MTD device spi0.0
[    0.909136] Creating 5 MTD partitions on "spi0.0":
[    0.914003] 0x000000000000-0x000000020000 : "u-boot"
[    0.920143] 0x000000020000-0x0000001b9550 : "kernel"
[    0.926805] 0x0000001b9550-0x000000ff0000 : "rootfs"
[    0.932461] mtd: device 2 (rootfs) set to be root filesystem
[    0.938284] 1 squashfs-split partitions found on MTD device rootfs
[    0.944569] 0x000000410000-0x000000ff0000 : "rootfs_data"
[    0.951889] 0x000000ff0000-0x000001000000 : "art"
[    0.957784] 0x000000020000-0x000000ff0000 : "firmware"
[    0.965364] libphy: Fixed MDIO Bus: probed
[    0.979861] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.674003] libphy: ag71xx_mdio: probed
[    2.306001] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.317246] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.604474] random: fast init done
[    2.946017] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[    2.953932] NET: Registered protocol family 10
[    2.962348] Segment Routing with IPv6
[    2.966190] NET: Registered protocol family 17
[    2.970745] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.984153] 8021q: 802.1Q VLAN Support v1.8
[    2.989743] hctosys: unable to open rtc device (rtc0)
[    2.999674] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.008049] Freeing unused kernel memory: 324K
[    3.012557] This architecture does not have kernel memory protection.
[    3.686354] init: Console is alive
[    3.689977] init: - watchdog -
[    4.843089] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.899088] usbcore: registered new interface driver usbfs
[    4.904760] usbcore: registered new interface driver hub
[    4.910234] usbcore: registered new device driver usb
[    4.919539] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.927537] ehci-platform: EHCI generic platform driver
[    4.932911] ehci-platform ehci-platform.0: EHCI Host Controller
[    4.938980] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    4.949251] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[    4.955374] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    4.984514] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    4.991659] hub 1-0:1.0: USB hub found
[    4.995816] hub 1-0:1.0: 1 port detected
[    5.000190] ehci-platform ehci-platform.1: EHCI Host Controller
[    5.006270] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[    5.016560] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[    5.022659] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    5.054521] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[    5.061715] hub 2-0:1.0: USB hub found
[    5.065829] hub 2-0:1.0: 1 port detected
[    5.070697] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.088407] init: - preinit -
[    6.286259] eth1: link up (1000Mbps/Full duplex)
[    6.309853] random: procd: uninitialized urandom read (4 bytes read)
[    9.687358] jffs2: notice: (467) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (3 unchecked, 3 orphan) and 44 of xref (3 dead, 0 orphan) found.
[    9.708540] mount_root: switching to jffs2 overlay
[    9.735361] overlayfs: upper fs does not support tmpfile.
[    9.752060] urandom-seed: Seeding with /etc/urandom.seed
[    9.802605] eth1: link down
[    9.822038] procd: - early -
[    9.825099] procd: - watchdog -
[   10.429535] procd: - watchdog -
[   10.432940] procd: - ubus -
[   10.475679] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.487303] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.494124] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.501372] procd: - init -
[   11.112882] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.199964] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.248213] u32 classifier
[   11.250959]     input device check on
[   11.254716]     Actions configured
[   11.270278] Mirror/redirect action on
[   11.285277] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   11.360274] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85
[   11.368081] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
[   11.397389] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.546378] xt_time: kernel timezone is -0000
[   11.713658] PPP generic driver version 2.4.2
[   11.720204] NET: Registered protocol family 24
[   11.748300] pci 0000:01:00.0: using irq 41 for pin 1
[   11.753347] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x3c.
[   11.762535] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   11.768484] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   12.049111] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[   12.059827] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.198058] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[   12.207251] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[   12.218129] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.359596] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[   12.370764] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[   12.381916] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.521835] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   12.532818] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[   12.543962] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.684597] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   12.694172] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[   12.705054] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.844440] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   12.853799] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[   12.864675] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.013649] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[   13.023055] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[   13.033936] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.175952] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[   13.185311] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[   13.196188] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.334549] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[   13.347444] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   13.356824] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   13.369210] ath10k_pci 0000:01:00.0: firmware ver 10.1-ct-8x-__fW-021-e2174c5 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT crc32 83fdb9cc
[   13.474685] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.485301] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.564141] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.594026] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.540994] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   14.557759] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410'
[   14.564050] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   14.572198] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[   14.634927] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   14.777340] ath: EEPROM regdomain: 0x0
[   14.777346] ath: EEPROM indicates default country code should be used
[   14.777349] ath: doing EEPROM country->regdmn map search
[   14.777362] ath: country maps to regdmn code: 0x3a
[   14.777366] ath: Country alpha2 being used: US
[   14.777369] ath: Regpair used: 0x3a
[   14.839679] ath: EEPROM regdomain: 0x0
[   14.839686] ath: EEPROM indicates default country code should be used
[   14.839689] ath: doing EEPROM country->regdmn map search
[   14.839701] ath: country maps to regdmn code: 0x3a
[   14.839706] ath: Country alpha2 being used: US
[   14.839709] ath: Regpair used: 0x3a
[   14.857189] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   14.858818] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[   14.963307] kmodloader: done loading kernel modules from /etc/modules.d/*
[   16.184461] urandom_read: 5 callbacks suppressed
[   16.189200] random: jshn: uninitialized urandom read (4 bytes read)
[   22.453912] eth1: link up (1000Mbps/Full duplex)
[   22.458725] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   22.483732] br-lan: port 1(eth1.1) entered blocking state
[   22.489260] br-lan: port 1(eth1.1) entered disabled state
[   22.495020] device eth1.1 entered promiscuous mode
[   22.499886] device eth1 entered promiscuous mode
[   22.549417] br-lan: port 1(eth1.1) entered blocking state
[   22.554932] br-lan: port 1(eth1.1) entered forwarding state
[   22.560715] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.608733] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.637041] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   23.763496] eth0: link up (1000Mbps/Full duplex)
[   23.779550] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   23.786344] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   23.793098] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   23.913079] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   25.324458] ath: EEPROM regdomain: 0x8114
[   25.328566] ath: EEPROM indicates we should expect a country code
[   25.334757] ath: doing EEPROM country->regdmn map search
[   25.340138] ath: country maps to regdmn code: 0x37
[   25.345006] ath: Country alpha2 being used: DE
[   25.349508] ath: Regpair used: 0x37
[   25.353039] ath: regdomain 0x8114 dynamically updated by user
[   25.358947] ath: EEPROM regdomain: 0x8114
[   25.363007] ath: EEPROM indicates we should expect a country code
[   25.369201] ath: doing EEPROM country->regdmn map search
[   25.374588] ath: country maps to regdmn code: 0x37
[   25.379445] ath: Country alpha2 being used: DE
[   25.383951] ath: Regpair used: 0x37
[   25.387502] ath: regdomain 0x8114 dynamically updated by user
[   28.409709] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   28.557504] br-lan: port 2(wlan1) entered blocking state
[   28.562904] br-lan: port 2(wlan1) entered disabled state
[   28.568679] device wlan1 entered promiscuous mode
[   28.573606] br-lan: port 2(wlan1) entered blocking state
[   28.579047] br-lan: port 2(wlan1) entered forwarding state
[   28.618336] br-lan: port 2(wlan1) entered disabled state
[   30.755326] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   30.772155] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410'
[   30.778534] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   30.786695] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[   30.871730] ath10k_pci 0000:01:00.0: set-coverage-class, phyclk: 88  value: 1
[   30.879591] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   30.960760] br-lan: port 3(wlan0) entered blocking state
[   30.966269] br-lan: port 3(wlan0) entered disabled state
[   30.971984] device wlan0 entered promiscuous mode
[   31.188324] ath10k_pci 0000:01:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   32.564798] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   32.571403] br-lan: port 2(wlan1) entered blocking state
[   32.576840] br-lan: port 2(wlan1) entered forwarding state
[   62.774516] random: crng init done
[   95.575098] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   95.581780] br-lan: port 3(wlan0) entered blocking state
[   95.587217] br-lan: port 3(wlan0) entered forwarding state

h8red · November 23, 2018, 4:24pm

Hi all. Still struggling to make USB storage work on ath79 Tp-link wr842nd v2. The same config and packages ar71xx works seamllesly. I am at a loss. More info:
https://forum.openwrt.org/t/porting-guide-ar71xx-to-ath79/13013/815

juppin · November 23, 2018, 4:29pm

New build:

Changelog:

kernel version 4.14.82

2018/11/23 (4.14.82-1-3f6379f96c9cbdee2d544e6019d873e7)

Included features / packages (build with: -O2):

default build:

same packages as on openwrt snapshot / trunk builds
support for ath9k dynack
luci

minimal build:

same packages as on openwrt snapshot / trunk builds
support for ath9k dynack

Supported device images:

D-LINK DIR-825 B1
NETGEAR WNDR3700
NETGEAR WNDR3700 V2
NETGEAR WNDR3800
Phicomm K2T
TP-Link Archer C7 V2
TP-Link RE450 V2
TP-Link WDR3600
TP-Link WDR4300
TP-Link WDR4900 V2
TP-Link WR1043 V1
TP-Link WR1043 V2
TP-Link WR1043 V3
TP-Link WR1043 V4
TP-Link WR2543 V1
Ubiquiti UniFi AC Pro
Ubiquiti UniFi AC-Mesh
Ubiquiti UniFi AC-Mesh Pro
Ubiquiti UniFi AC-Lite
Ubiquiti UniFi RouterStation Pro

Download 4.14.82 (default build)

Download 4.14.82 (minimal build)

olek87 · November 23, 2018, 8:00pm

Hi,
I installed this build on my archer c7 v2 - its working well with one exeption: wds on 5ghz.
systemlog: daemon.err hostapd: Failed to create interface wlan0-1.sta1: -122 (Not supported)
if i understand correctly there is a problem with dynamic vlan creation. i found this thread regarding the issue: https://patchwork.kernel.org/patch/10380037/ - is this a valid patch?

thank you for your great work!

SaberJ2X · November 24, 2018, 3:44pm

will the WNDR3700v4 be considered for this? or no nand driver for 4.14?

anon20279570 · November 26, 2018, 8:49am

I also have this question. Yesterday i build firmware for my WNDR3700v4 and looks like it's already on 4.14 kernel but i chose ar71xx as target. What is the difference between ar71xx and ath79 except that LEDs can't be controlled on ath79?

Pilot6 · November 26, 2018, 7:05pm

The probably can't be controlled because of nbd ccab68f2d commit. If you revert it, LEDs should work.

maciekph · November 26, 2018, 10:35pm

How should I flash it correctly having snapshot of ar71xx installed on WDR4300 ?
Factory file or systemupgrade one via LUCI?

Thnx!

slh · November 26, 2018, 10:47pm

sysupgrade, using the sysupgrade image - you might need to use -F | --force (Flash image even if image checks fail, this is dangerous!) as the device names have changed for many devices, you definately need to use -n (do not save configuration over reflash) as (wireless) device path have changed.

Pilot6 · November 27, 2018, 9:24am

You can upgrade it a normal way using Luci. It is highly recommnded to uncheck "keep settings".
Thee is no need to force it. But if you want to return to ar71xx, you'll need to use the force option.

RelentlesS · November 28, 2018, 11:48am

Kernel Log 4.14.81 ar71xx Snapshot from Wed Nov 21

You may look for:

firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon

Kernel Log 4.14.81 ar71xx Snapshot from Wed Nov 21 after reboot on Mon Nov 26

[    0.000000] Linux version 4.14.81 (buildbot@slashdirt-03) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8474-0191a06)) #0 Wed Nov 21 14:15:05 2018
[    0.000000] MyLoader: sysp=02000000, boardp=00000000, parts=00000000
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 8053c910, node_mem_map 81000020
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x47c with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=ARCHER-C7-V2  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 123976K/131072K available (3865K kernel code, 190K rwdata, 924K rodata, 324K init, 211K bss, 7096K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008293] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.074984] pid_max: default: 32768 minimum: 301
[    0.080076] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.087114] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.096387] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.106878] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.114304] NET: Registered protocol family 16
[    0.120147] MIPS: machine is TP-LINK Archer C7
[    0.127931] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.133431] registering PCI controller with io_map_base unset
[    0.139666] registering PCI controller with io_map_base unset
[    0.639173] PCI host bridge to bus 0000:00
[    0.643540] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.650886] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.656815] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.664040] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.672476] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.672576] PCI host bridge to bus 0000:01
[    0.676955] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[    0.684264] pci_bus 0000:01: root bus resource [io  0x0001]
[    0.690195] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.697411] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.705866] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
[    0.705921] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.705975] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    0.706048] pci 0000:01:00.0: supports D1 D2
[    0.706214] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.706235] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.714028] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[    0.724486] clocksource: Switched to clocksource MIPS
[    0.730701] NET: Registered protocol family 2
[    0.736088] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.743508] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750313] TCP: Hash tables configured (established 1024 bind 1024)
[    0.757188] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.763411] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.770298] NET: Registered protocol family 1
[    0.774997] PCI: CLS 0 bytes, default 32
[    0.777317] Crashlog allocated RAM at address 0x3f00000
[    0.783879] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.794955] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.801156] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.818999] io scheduler noop registered
[    0.823173] io scheduler deadline registered (default)
[    0.829022] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.837507] console [ttyS0] disabled
[    0.861380] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.870565] console [ttyS0] enabled
[    0.877983] bootconsole [early0] disabled
[    0.891793] m25p80 spi0.0: found s25fl128s, expected m25p80
[    0.897526] m25p80 spi0.0: s25fl128s (16384 Kbytes)
[    0.903420] 5 tp-link partitions found on MTD device spi0.0
[    0.909105] Creating 5 MTD partitions on "spi0.0":
[    0.913972] 0x000000000000-0x000000020000 : "u-boot"
[    0.920110] 0x000000020000-0x0000001b9550 : "kernel"
[    0.926770] 0x0000001b9550-0x000000ff0000 : "rootfs"
[    0.932428] mtd: device 2 (rootfs) set to be root filesystem
[    0.938255] 1 squashfs-split partitions found on MTD device rootfs
[    0.944538] 0x000000410000-0x000000ff0000 : "rootfs_data"
[    0.951856] 0x000000ff0000-0x000001000000 : "art"
[    0.957742] 0x000000020000-0x000000ff0000 : "firmware"
[    0.965312] libphy: Fixed MDIO Bus: probed
[    0.979806] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.674009] libphy: ag71xx_mdio: probed
[    2.306010] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.317260] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.604483] random: fast init done
[    2.946027] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[    2.953948] NET: Registered protocol family 10
[    2.962369] Segment Routing with IPv6
[    2.966212] NET: Registered protocol family 17
[    2.970767] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.984177] 8021q: 802.1Q VLAN Support v1.8
[    2.989743] hctosys: unable to open rtc device (rtc0)
[    2.999675] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.008037] Freeing unused kernel memory: 324K
[    3.012544] This architecture does not have kernel memory protection.
[    3.686160] init: Console is alive
[    3.689775] init: - watchdog -
[    4.842481] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.897615] usbcore: registered new interface driver usbfs
[    4.903262] usbcore: registered new interface driver hub
[    4.908768] usbcore: registered new device driver usb
[    4.918208] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.926207] ehci-platform: EHCI generic platform driver
[    4.931579] ehci-platform ehci-platform.0: EHCI Host Controller
[    4.937646] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    4.947917] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[    4.954016] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    4.984523] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    4.991706] hub 1-0:1.0: USB hub found
[    4.995837] hub 1-0:1.0: 1 port detected
[    5.000206] ehci-platform ehci-platform.1: EHCI Host Controller
[    5.006281] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[    5.016572] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[    5.022673] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    5.054530] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[    5.061719] hub 2-0:1.0: USB hub found
[    5.065832] hub 2-0:1.0: 1 port detected
[    5.070688] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.088405] init: - preinit -
[    6.286596] eth1: link up (1000Mbps/Full duplex)
[    6.310280] random: procd: uninitialized urandom read (4 bytes read)
[    9.687896] jffs2: notice: (467) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (3 unchecked, 4 orphan) and 45 of xref (4 dead, 0 orphan) found.
[    9.709079] mount_root: switching to jffs2 overlay
[    9.736384] overlayfs: upper fs does not support tmpfile.
[    9.751522] urandom-seed: Seeding with /etc/urandom.seed
[    9.800869] eth1: link down
[    9.821712] procd: - early -
[    9.824767] procd: - watchdog -
[   10.429430] procd: - watchdog -
[   10.432839] procd: - ubus -
[   10.476214] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.487228] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.494048] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.501268] procd: - init -
[   11.113257] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.200344] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.249402] u32 classifier
[   11.252152]     input device check on
[   11.255908]     Actions configured
[   11.270450] Mirror/redirect action on
[   11.285350] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   11.355772] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85
[   11.363542] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
[   11.397383] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.547915] xt_time: kernel timezone is -0000
[   11.714174] PPP generic driver version 2.4.2
[   11.720716] NET: Registered protocol family 24
[   11.747758] pci 0000:01:00.0: using irq 41 for pin 1
[   11.752807] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x3c.
[   11.761995] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   11.767936] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   12.049129] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[   12.059839] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.199835] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[   12.209024] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[   12.219902] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.361161] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[   12.372333] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[   12.383487] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.522388] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   12.533371] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[   12.544521] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.685076] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   12.694692] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[   12.705563] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.846767] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   12.856153] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[   12.867030] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.014975] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[   13.024300] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[   13.035186] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.178471] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[   13.187858] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[   13.198735] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.341515] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[   13.354438] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   13.363837] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   13.376244] ath10k_pci 0000:01:00.0: firmware ver 10.1-ct-8x-__fW-021-e2174c5 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT crc32 83fdb9cc
[   13.481390] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.492021] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.570014] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.598912] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.544926] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   14.561659] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410'
[   14.567990] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   14.576135] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[   14.639869] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   14.777351] ath: EEPROM regdomain: 0x0
[   14.777357] ath: EEPROM indicates default country code should be used
[   14.777360] ath: doing EEPROM country->regdmn map search
[   14.777373] ath: country maps to regdmn code: 0x3a
[   14.777378] ath: Country alpha2 being used: US
[   14.777381] ath: Regpair used: 0x3a
[   14.840131] ath: EEPROM regdomain: 0x0
[   14.840137] ath: EEPROM indicates default country code should be used
[   14.840140] ath: doing EEPROM country->regdmn map search
[   14.840153] ath: country maps to regdmn code: 0x3a
[   14.840157] ath: Country alpha2 being used: US
[   14.840161] ath: Regpair used: 0x3a
[   14.857593] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   14.859214] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[   14.963727] kmodloader: done loading kernel modules from /etc/modules.d/*
[   16.250858] urandom_read: 5 callbacks suppressed
[   16.250864] random: jshn: uninitialized urandom read (4 bytes read)
[   22.512901] eth1: link up (1000Mbps/Full duplex)
[   22.517714] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   22.545434] br-lan: port 1(eth1.1) entered blocking state
[   22.550916] br-lan: port 1(eth1.1) entered disabled state
[   22.556690] device eth1.1 entered promiscuous mode
[   22.561552] device eth1 entered promiscuous mode
[   22.612229] br-lan: port 1(eth1.1) entered blocking state
[   22.617756] br-lan: port 1(eth1.1) entered forwarding state
[   22.623542] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.675879] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.709984] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   23.564570] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   23.571323] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   23.826010] eth0: link up (1000Mbps/Full duplex)
[   23.836779] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   23.893705] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   25.259469] ath: EEPROM regdomain: 0x8114
[   25.263539] ath: EEPROM indicates we should expect a country code
[   25.269757] ath: doing EEPROM country->regdmn map search
[   25.275148] ath: country maps to regdmn code: 0x37
[   25.280004] ath: Country alpha2 being used: DE
[   25.284518] ath: Regpair used: 0x37
[   25.288056] ath: regdomain 0x8114 dynamically updated by user
[   25.293951] ath: EEPROM regdomain: 0x8114
[   25.298030] ath: EEPROM indicates we should expect a country code
[   25.304202] ath: doing EEPROM country->regdmn map search
[   25.309598] ath: country maps to regdmn code: 0x37
[   25.314454] ath: Country alpha2 being used: DE
[   25.318970] ath: Regpair used: 0x37
[   25.322507] ath: regdomain 0x8114 dynamically updated by user
[   28.391360] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   28.547502] br-lan: port 2(wlan1) entered blocking state
[   28.552894] br-lan: port 2(wlan1) entered disabled state
[   28.558597] device wlan1 entered promiscuous mode
[   28.563532] br-lan: port 2(wlan1) entered blocking state
[   28.568964] br-lan: port 2(wlan1) entered forwarding state
[   28.645809] br-lan: port 2(wlan1) entered disabled state
[   30.838591] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   30.855385] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410'
[   30.861831] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   30.870004] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 23868 iram: 26712'
[   30.958850] ath10k_pci 0000:01:00.0: set-coverage-class, phyclk: 88  value: 1
[   30.971939] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   31.097604] br-lan: port 3(wlan0) entered blocking state
[   31.103004] br-lan: port 3(wlan0) entered disabled state
[   31.108704] device wlan0 entered promiscuous mode
[   31.223705] ath10k_pci 0000:01:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   32.549494] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   32.556126] br-lan: port 2(wlan1) entered blocking state
[   32.561524] br-lan: port 2(wlan1) entered forwarding state
[   72.954843] random: crng init done
[   95.554172] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   95.561125] br-lan: port 3(wlan0) entered blocking state
[   95.566559] br-lan: port 3(wlan0) entered forwarding state
[85827.471084] ath10k_pci 0000:01:00.0: rx ring became corrupted: -5

You may look for:

ath10k_pci 0000:01:00.0: rx ring became corrupted: -5

since this last Log entry the 5GHz WiFi is not available

@juppin can I switch back to your ath79 build or are you interested in any more ar71xx comparison logs?