Hello everyone. I am trying to setup an adhoc network with meshing on a Turris Omnia and noticed that ath10k fails to load its firmware. I have the kernel log pasted below. Does anyone know why this might be?
[ 9.247317] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 9.483204] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[ 9.493936] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 9.520946] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 9.530025] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[ 9.540418] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 9.550420] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 9.559737] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 9.570479] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 9.580423] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 9.590296] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 9.599562] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 9.609082] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb
[ 9.653858] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 9.664327] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 9.674588] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 9.709276] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 10.845287] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 10.961123] ath: EEPROM regdomain: 0x0
[ 10.961126] ath: EEPROM indicates default country code should be used
[ 10.961128] ath: doing EEPROM country->regdmn map search
[ 10.961131] ath: country maps to regdmn code: 0x3a
[ 10.961133] ath: Country alpha2 being used: US
[ 10.961135] ath: Regpair used: 0x3a
[ 11.063463] ath: EEPROM regdomain: 0x0
[ 11.063467] ath: EEPROM indicates default country code should be used
[ 11.063469] ath: doing EEPROM country->regdmn map search
[ 11.063473] ath: country maps to regdmn code: 0x3a
[ 11.063475] ath: Country alpha2 being used: US
[ 11.063476] ath: Regpair used: 0x3a
I also read through the other thread on ath10k crashing. Its a similar yet different problem I think. Here ath10k never completely crashes and the only error codes I get are -2.