Hi,
I just bought Asus RT-AC59U V2
I knew openwrt has not support this one...
the device have some nice standard software feature (not advertise on its website) :
but NO PrintServer support for USB
may be someone interested with its hardware info and produce Openwrt build ?
(next post)
--== dmesg ==--
Linux version 3.3.8 (root@asus) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed Sep 16 13:54:15 CST 2020
CPU revision is: 00019750 (MIPS 74Kc)
SoC: Qualcomm Atheros QCA5502 rev 0
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00008000
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00008000
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat 803c03f0, node_mem_map 81000000
Normal zone: 256 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512
Kernel command line: board=APJET01 console=ttyS0,115200 root=/dev/mtdblock4 roo tfstype=squashfs mem=128M
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 125644k/131072k available (2687k kernel code, 5428k reserved, 771k data, 204k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Invalid signature of oopsbuf: 13-41-08-A2-49-04-98-83 (len -784330396)
NR_IRQS:83
Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
gpiochip_add: registered GPIOs 0 to 19 on device: ath79
MIPS: machine is Qualcomm Atheros APJET01 reference board
WLAN firmware dump buffer allocation of 2097152 bytes @ address 0x87e00000- SUCC ESS !!!
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
pci_bus 0000:00: root bus resource [io 0x0001]
pci 0000:00:00.0: [168c:0056] type 0 class 0x000280
pci 0000:00:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit]
pci 0000:00:00.0: PME# supported from D0 D3hot
pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
pci 0000:00:00.0: using irq 40 for pin 1
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 245
alg: No test for xz (xz-generic)
alg: No test for stdrng (krng)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled
brd: module loaded
ath79-spi ath79-spi: cs1 >= max 1
ath79-spi ath79-spi: can't create new device for m25p80
m25p80 spi0.0: found mx25l25635e, expected m25p80
m25p80 spi0.0: mx25l25635e (32768 Kbytes)
Creating 7 MTD partitions on "ath79-nor0":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000050000 : "nvram"
0x000000050000-0x000000060000 : "Factory"
0x000000060000-0x000001d00000 : "linux"
0x00000019ab80-0x000001d00000 : "rootfs"
0x000001d00000-0x000002000000 : "jffs2"
0x000000000000-0x000002000000 : "ALL"
IMQ driver loaded successfully. (numdevs = 8, numqueues = 1)
Hooking IMQ after NAT on PREROUTING.
Hooking IMQ before NAT on POSTROUTING.
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4, MAC 00:E7:F7:XX:XX:XX
eth0: Atheros AR8327/AR8337 switch driver attached.
ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, drive r=Atheros AR8216/AR8236/AR8316]
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
u32 classifier
nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
xt_time: kernel timezone is -0000
GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Bridge firewalling registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
L2TP netlink interface
8021q: 802.1Q VLAN Support v1.8
### of_selftest(): No testcase data in device tree; not running tests
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 204k freed
offset 0x1000 elapse 0ms
found private data block and skip it
bled: GPIO#15: netdev ath0.
bled: GPIO#5: netdev ath1.
ssdk_switch_device_num_init[985]:INFO:ess-switch dts node number: 1
ssdk_plat_init start
ssdk_driver_register[2427]:INFO:Register QCA PHY driver
f1_phy_api_ops_init[1513]:INFO:qca probe f1 phy driver succeeded!
regi_init[3370]:INFO:qca-ssdk module init succeeded!
mem_manager: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_spectral: Version 2.0.0
Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Right s Reserved
ath_tx99: Version 2.0
Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserve d
JET_PRINT: init_ath_wmac[240]: Checking devid: 40
__ath_attach: Set global_scn[0]
*** All the minfree values should be <= ATH_TXBUF-32, otherwise default value wi ll be used instead ***
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ATH_TXBUF=2700
JET_PRINT: ath_hal_attach[389]: Jet support is enabled. devid: 40
Enterprise mode: 0x03bda000
Restoring Cal data from DRAM
ath_mtd_read: read [Factory] from 0x1000 len 1868
ART Version : -48.0.0
SW Image Version : -48.0.0.0.0
Board Revision :
ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
HAL_CAP_TXDESCLEN : 128
HAL_CAP_TXSTATUSLEN : 36
HAL_CAP_RXSTATUSLEN : 56
SPECTRAL : get_capability not registered
HAL_CAP_PHYDIAG : Capable
SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 242)
SPECTRAL : get_capability not registered
HAL_CAP_RADAR : Capable
SPECTRAL : Need to fix the capablity check for SPECTRAL
(spectral_attach : 247)
SPECTRAL : get_capability not registered
HAL_CAP_SPECTRAL_SCAN : Capable
SPECTRAL : get_tsf64 not registered
spectral_init_netlink 85 NULL SKB
SPECTRAL : No ADVANCED SPECTRAL SUPPORT
SPECTRAL :----- module attached
Green-AP : Green-AP : Attached
Starting random number generator thread
ath_get_caps[6248] rx chainmask mismatch actual 15 sc_chainmak 0
ath_get_caps[6211] tx chainmask mismatch actual 15 sc_chainmak 0
ieee80211_cbs_init CBS Inited
band steering initialized for direct attach hardware
ieee80211_bsteering_attach: Band steering initialized
acfg_attach: 2979: Netlink socket created:86b82600
ath_attach_dfs[12767] dfsdomain 1
dfs_attach: event log enabled by default
SPECTRAL : module already attached
ath_attach: Set global_ic[1]..gloabl_ic ptr:8675fe30
osif_wrap_attach:444 osif wrap attached
osif_wrap_devt_init:405 osif wrap dev table init done
Wrap Attached: Wrap_com =86b82e00 ic->ic_wrap_com=86b82e00 &wrap_com->wc_devt=8 6b82e00
ath_tx_paprd_init sc 86ad0000 PAPRD disabled in HAL
ath_thermal_mitigation_attach: --
wifi0: Qualcomm Atheros 5500: mem_start: =0xb8100000, mem_end: =0xb8120000, irq= 47
ath_da_pci: (Atheros/multi-bss)
ath_ol_pci: (Atheros/multi-bss)
hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56
ath_ol_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci _enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_ tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW s ignal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hi a: Ehif_set_hia_extnd: E
chip_id 0xc chip_revision 0x0
CLOCK PLL skipped
hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff
hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL
hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_leg acy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_creat e: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_n api_create: napi instance 32 created on pipe 4
hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: settin g configuration to ON
__ol_ath_attach() Allocated scn 85f00380
__ol_ath_attach: dev name wifi1
ol_ath_attach interface_id 1
ol_target_init() BMI inited.
ol_target_init() BMI Get Target Info.
Chip id: 0xc, chip version: 0x1000000
CE WAR Disabled
NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
ol_target_init() configure Target .
Target Version is 1000000
Flash Download Address c0000
ol_transfer_bin_file: flash data file defined
ath_mtd_read: read [Factory] from 0x5000 len 12064
qc98xx_verify_checksum: flash checksum passed: 0x93e8
ol_transfer_bin_file 3927: Download Flash data len 12064
Board extended Data download address: 0x0
Board data initialized
ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
Selecting OTP binary for CHIP Version 0
ol_transfer_bin_file 3733: downloading file 0, Download data len 9116
First OTP send param 8000
ol_ath_download_firmware :First OTP download and Execute is good address:0x4000 return param 4660
ol_ath_download_firmware:##Board Id 16 , CHIP Id 0
ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
wifi1: Selecting board data file name boardData_2_0_QCA9888_5G_Y9690.bin
ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9 888/hw.2/boardData_2_0_QCA9888_5G_Y9690.bin
ol_transfer_bin_file 3733: downloading file 3, Download data len 12064
Board extended Data download address: 0x0
ol_ath_download_firmware: Using 0x1234 for the remainder of init
Selecting OTP binary for CHIP Version 0
ol_transfer_bin_file 3733: downloading file 0, Download data len 9116
[Flash] : Ignore Module param
Second otp download Param 10000
ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
Mission mode: Firmware CHIP Version 0
ol_swap_seg_alloc: Successfully allocated memory for SWAP size=524288
ol_swap_wlan_memory_expansion: length:278491 size_left:278511 dma_size_left:5242 88 fw_temp:c082c004 fw_entry_size:278515
ol_swap_wlan_memory_expansion: dma_virt_addr :a5900000 fw_temp: c082c008 length: 278491
Swap: bytes_left to copy: fw:16; dma_page:245797
ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:245797 fw_tem p:c086ffe7 fw_entry_size:278515
Swap: wrong length read:0
ol_swap_wlan_memory_expansion: Swap total_bytes copied: 278491 Target address 41 af58
scn=85f00380 target_write_addr=41af58 seg_info=85f79610
ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/a thwlan.codeswap.bin
ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
ol_transfer_bin_file 3733: downloading file 1, Download data len 395380
ol_target_init() Download FW done.
ol_ath_attach() WMI attached. wmi_handle 863d2000
wmi_unified_register_event_handler: Event id 62 is unavailable
+htc_create .. HIF :85f50000-htc_create: (0x863b6000)
htc_wmi_init() HT Create . 863b6000
htc_wmi_init 8437 host_enable 0 nss_nwifi_offload 0
ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module para m (umac.ko)
OL_ACBKMinfree : 0
OL_ACBEMinfree : 0
OL_ACVIMinfree : 0
OL_ACVOMinfree : 0
hif_enable_fastpath, Enabling fastpath mode
+HWT
hif_completion_thread_startup: pipe_num:0 pipe_info:0x85f5306chif_completion_thr ead_startup: pipe_num:3 pipe_info:0x85f5312chif_completion_thread_startup: pipe_ num:4 pipe_info:0x85f5316c
-HWT
Startup Mode-0 set
htt_peer_map_timer_init Enter pdev 85770000 hrtimer 85774970
htt_alloc_peer_map_mem : Alloc Success : host q vaddr 85a6c000 paddr 5a6c000
htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 84fe0000
Firmware_Build_Number:83
FW wireless modes: 0x1f9001
num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979b2 vht_su pp_mcs:0x0000fffa
wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0
Sending Ext resource cfg: HOST PLATFORM as 1
fw_feature_bitmap as 50 to TGT
ol_ath_service_ready_event: tt_support: 1
ol_ath_service_ready_event: periodic_chan_stats: 1
ol_ath_service_ready_event: sw_cal_support_check_flag: 1
Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, nu m_vdevs = 17
EXT NSS Supported
idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53
ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,
idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53
ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,
idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53
ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,
idx 6 req 9 num_units 1 num_unit_info 8 unit size 819200 actual units 1
ol_ath_alloc_host_mem_chunk req_id 9 idx 3 num_units 1 unit_len 819200,
idx 0 req 1 num_units 0 num_unit_info 2 unit size 880 actual units 531
ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 531 unit_len 880,
idx 4 req 5 num_units 0 num_unit_info 2 unit size 2076 actual units 531
ol_ath_alloc_host_mem_chunk req_id 5 idx 5 num_units 531 unit_len 2076,
Support not added yet for Service 91
Support not added yet for Service 92
No EXT_MSG send INIT now
chunk 0 len 13568 requested , ptr 0x5ed4000
chunk 1 len 54272 requested , ptr 0x4840000
chunk 2 len 217088 requested , ptr 0x4880000
chunk 3 len 819200 requested , ptr 0x4900000
chunk 4 len 467280 requested , ptr 0x4a00000
chunk 5 len 1102356 requested , ptr 0x4400000
chunk 6 len 0 requested , ptr 0xffffffff
ol_ath_service_ready_event[4288] WAPI MBSSID 2
smart_log_init: Smart logging Enabled buf=pK-error (size=65536)
Version = 16777216 3 status = 0
ol_ath_connect_htc() WMI is ready
htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1
target uses HTT version 2.2; host uses 2.2
ol_ath_attach() connect HTC.
bypasswmi : 0
ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Add VHT80 channel: 5690
Add VHT80 channel: 5775
Skipping VHT80 channel 5825
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100
ol_ath_phyerr_attach: called
freq=58
freq=106
freq=122
OL Resmgr Init-ed
ieee80211_cbs_init CBS Inited
ieee80211_bsteering_attach: Band steering initialized
acfg_attach: using existing sock 86b82600
ol_if_spectral_setup
SPECTRAL : get_capability not registered
HAL_CAP_PHYDIAG : Capable
SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 242)
SPECTRAL : get_capability not registered
HAL_CAP_RADAR : Capable
SPECTRAL : Need to fix the capablity check for SPECTRAL
(spectral_attach : 247)
SPECTRAL : get_capability not registered
HAL_CAP_SPECTRAL_SCAN : Capable
SPECTRAL : get_tsf64 not registered
spectral_init_netlink 85 NULL SKB
Green-AP : Green-AP : Attached
Green-AP : Attached
rate power table override is only supported for AR98XX
ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.
ol_if_dfs_setup: called
ol_if_dfs_attach: called; ptr=848c997c, radar_info=86d85b38
dfs_attach: event log enabled by default
ol_ath_rtt_meas_report_attach: called
ol_ath_lowi_wmi_event_attach: called
>>>> CB Set 00000000
ol_ath_attach() UMAC attach .
BURSTING enabled by default
ol_ath_attach: Set global_ic[2] ..ptr:8675fe30
ath_lowi_if_netlink_init LOWI Netlink successfully created
osif_wrap_attach:444 osif wrap attached
osif_wrap_devt_init:405 osif wrap dev table init done
Wrap Attached: Wrap_com =863b0000 ic->ic_wrap_com=863b0000 &wrap_com->wc_devt=8 63b0000
__ol_ath_attach: needed_headroom reservation 60
ol_ath_thermal_mitigation_attach: --
ol_ath_pci_probe num_radios=0, wifi_radios[0].sc = 85f00380 wifi_radio_type = 2
ath_sysfs_diag_init: diag_fsattr
Suspending Target scn=85f00380
waiting for target paused event from target
ol_ath_thermal_mitigation_detach: ++
ol_ath_thermal_mitigation_detach: --
freq=58
freq=106
freq=122
ol_if_dfs_clist_update: called, cmd=1, nollist=00000000, nentries=0
ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deini t: Smart logging Disabled
ol_tx_me_exit: Already Disabled !!!
hif_pci_device_reset: Reset Devicehif_pci_disable_bus: Xhif_disable: Xhif_napi_d estroy: NAPI 6 destroyed
hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr
ath_net80211_dfs_clist_update: called, cmd=1, nollist=00000000, nentries=0
ath_attach_dfs[12767] dfsdomain 1
dfs_attach: event log enabled by default
sc nodebug 0
Starting the target before sending the command
hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56
ath_ol_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci _enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_ tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW s ignal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hi a: Ehif_set_hia_extnd: E
chip_id 0xc chip_revision 0x0
CLOCK PLL skipped
hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff
hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL
hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_leg acy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_creat e: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_n api_create: napi instance 32 created on pipe 4
hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: settin g configuration to ON
ol_target_init() BMI inited.
ol_target_init() BMI Get Target Info.
Chip id: 0xc, chip version: 0x1000000
CE WAR Disabled
NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
ol_target_init() configure Target .
dmesg continue....
Target Version is 1000000
Flash Download Address c0000
ol_transfer_bin_file: flash data file defined
ath_mtd_read: read [Factory] from 0x5000 len 12064
qc98xx_verify_checksum: flash checksum passed: 0x93e8
ol_transfer_bin_file 3927: Download Flash data len 12064
Board extended Data download address: 0x0
Board data initialized
ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
Selecting OTP binary for CHIP Version 0
ol_transfer_bin_file 3733: downloading file 0, Download data len 9116
First OTP send param 8000
ol_ath_download_firmware :First OTP download and Execute is good address:0x4000 return param 4660
ol_ath_download_firmware:##Board Id 16 , CHIP Id 0
ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
wifi1: Selecting board data file name boardData_2_0_QCA9888_5G_Y9690.bin
ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9 888/hw.2/boardData_2_0_QCA9888_5G_Y9690.bin
ol_transfer_bin_file 3733: downloading file 3, Download data len 12064
Board extended Data download address: 0x0
ol_ath_download_firmware: Using 0x1234 for the remainder of init
Selecting OTP binary for CHIP Version 0
ol_transfer_bin_file 3733: downloading file 0, Download data len 9116
[Flash] : Ignore Module param
Second otp download Param 10000
ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
Mission mode: Firmware CHIP Version 0
ol_swap_wlan_memory_expansion: length:278491 size_left:278511 dma_size_left:5242 88 fw_temp:c0955004 fw_entry_size:278515
ol_swap_wlan_memory_expansion: dma_virt_addr :a5900000 fw_temp: c0955008 length: 278491
Swap: bytes_left to copy: fw:16; dma_page:245797
ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:245797 fw_tem p:c0998fe7 fw_entry_size:278515
Swap: wrong length read:0
ol_swap_wlan_memory_expansion: Swap total_bytes copied: 278491 Target address 41 af58
scn=85f00380 target_write_addr=41af58 seg_info=85f79610
ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/a thwlan.codeswap.bin
ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
ol_transfer_bin_file 3733: downloading file 1, Download data len 395380
ol_target_init() Download FW done.
+htc_create .. HIF :85d28000-htc_create: (0x84ac9000)
htc_wmi_init() HT Create . 84ac9000
htc_wmi_init 8437 host_enable 0 nss_nwifi_offload 0
ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module para m (umac.ko)
OL_ACBKMinfree : 0
OL_ACBEMinfree : 0
OL_ACVIMinfree : 0
OL_ACVOMinfree : 0
hif_enable_fastpath, Enabling fastpath mode
+HWT
hif_completion_thread_startup: pipe_num:0 pipe_info:0x85d2b06chif_completion_thr ead_startup: pipe_num:3 pipe_info:0x85d2b12chif_completion_thread_startup: pipe_ num:4 pipe_info:0x85d2b16c
-HWT
wmi_unified_register_event_handler : event handler already registered 0x8002
Startup Mode-0 set
htt_peer_map_timer_init Enter pdev 84f70000 hrtimer 84f74970
htt_alloc_peer_map_mem : Alloc Success : host q vaddr 848c4000 paddr 48c4000
htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 84ea0000
Firmware_Build_Number:83
FW wireless modes: 0x1f9001
num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979b2 vht_su pp_mcs:0x0000fffa
wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0
Sending Ext resource cfg: HOST PLATFORM as 1
fw_feature_bitmap as 50 to TGT
ol_ath_service_ready_event: tt_support: 1
ol_ath_service_ready_event: periodic_chan_stats: 1
ol_ath_service_ready_event: sw_cal_support_check_flag: 1
Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, nu m_vdevs = 17
EXT NSS Supported
idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53
ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,
idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53
ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,
idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53
ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,
idx 6 req 9 num_units 1 num_unit_info 8 unit size 819200 actual units 1
ol_ath_alloc_host_mem_chunk req_id 9 idx 3 num_units 1 unit_len 819200,
idx 0 req 1 num_units 0 num_unit_info 2 unit size 880 actual units 531
ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 531 unit_len 880,
idx 4 req 5 num_units 0 num_unit_info 2 unit size 2076 actual units 531
ol_ath_alloc_host_mem_chunk req_id 5 idx 5 num_units 531 unit_len 2076,
Support not added yet for Service 91
Support not added yet for Service 92
No EXT_MSG send INIT now
chunk 0 len 13568 requested , ptr 0x5ed4000
chunk 1 len 54272 requested , ptr 0x4840000
chunk 2 len 217088 requested , ptr 0x4880000
chunk 3 len 819200 requested , ptr 0x4900000
chunk 4 len 467280 requested , ptr 0x4a00000
chunk 5 len 1102356 requested , ptr 0x4400000
chunk 6 len 0 requested , ptr 0xffffffff
ol_ath_service_ready_event[4288] WAPI MBSSID 2
smart_log_init: Smart logging Enabled buf=pK-error (size=65536)
Version = 16777216 3 status = 0
ol_ath_connect_htc() WMI is ready
htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1
target uses HTT version 2.2; host uses 2.2
wmi_unified_register_event_handler : event handler already registered 0x900b
wmi_unified_register_event_handler : event handler already registered 0x9042
>>>> CB Set 00000000
ol_ath_thermal_mitigation_attach: --
ol_if_dfs_setup: called
ath_sysfs_diag_init: diag_fsattr
+hif_update_pipe_callback pipeid 8
-hif_update_pipe_callback
isCountryCodeValid: EEPROM regdomain 0x0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5775
Skipping VHT80 channel 5825
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100
wlan_vap_create : enter. devhandle=0x86b50380, opmode=IEEE80211_M_HOSTAP, flags= 0x1
ieee80211_mbo_vattach:MBO Initialized
ieee80211_oce_vattach: OCE Initialized
wlan_vap_create : exit. devhandle=0x86b50380, vap=0x84c00000, opmode=IEEE80211_M _HOSTAP, flags=0x1.
__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
VAP device ath0 created osifp: (84ac9b80) os_if: (84c00000)
[wifi1] FWLOG: [5261] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[wifi1] FWLOG: [5261] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[wifi1] FWLOG: [5261] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[wifi1] FWLOG: [5261] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[wifi1] FWLOG: [5261] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )
[wifi1] FWLOG: [5393] WAL_DBGID_PDEV_INFO_PRINT ( 0x14, 0xa10, 0x610, 0x10, 0x0 )
[wifi1] FWLOG: [5393] WAL_DBGID_PDEV_INFO_PRINT ( 0x14, 0x10, 0x0, 0x10, 0x12 )
wlan_vap_create : enter. devhandle=0x85f00380, opmode=IEEE80211_M_HOSTAP, flags= 0x1
send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 50:eb:f6:6 6:55:14:
ieee80211_mbo_vattach:MBO Initialized
ieee80211_oce_vattach: OCE Initialized
wlan_vap_create : exit. devhandle=0x85f00380, vap=0x84c18000, opmode=IEEE80211_M _HOSTAP, flags=0x1.
__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
Enabling TX checksum bit for the vap ath1 features 4000
Enabling SG bit for the vap ath1 features 4000
Enabling SG bit for the vap ath1 features 4000
Enabling TSO bit for the vap ath1 features 4000
Enabling LRO bit for the vap ath1 features 4000
VAP device ath1 created osifp: (863b6380) os_if: (84c18000)
JFFS2 version 2.2 (NAND) (ZLIB) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Switching to Tx Mode-0
nvram_commit(): pid 1 comm [init]
found private data block and skip it
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform ehci-platform.0: Generic Platform EHCI Controller
ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): vlan1: link is not ready
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device ath0 entered promiscuous mode
device ath1 entered promiscuous mode
ADDRCONF(NETDEV_UP): br0: link is not ready
DCS for CW interference mitigation: 0
DCS for WLAN interference mitigation: 0
set TXBF_SND_PERIOD: value 100 wmi_status 0
[wifi1] FWLOG: [11888] WAL_DBGID_DEV_RESET ( 0xc01d, 0x472 )
eth0: link up (1000Mbps/Full duplex)
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
br0: topology change detected, propagating
br0: port 1(vlan1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[DEBUG] vap-0(ath0):set SIOC80211NWID, 7 characters
DES SSID SET=asus24g
br0: topology change detected, propagating
br0: port 2(ath0) entered forwarding state
br0: port 2(ath0) entered forwarding state
8021q: adding VLAN 0 to HW filter on device ath0
---- ACS CALCULATE ----
Chan 11 pre_param 5 param 5
Best Channel Selected 11
ieee80211_derive_chan : Overriding HT40 channel with HT20 channel
__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_ncm
ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
br0: port 2(ath0) entered disabled state
DEVICE IS DOWN ifname=ath0
DEVICE IS DOWN ifname=ath0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Warning: node not in table 0x8466e000
br0: topology change detected, propagating
br0: port 2(ath0) entered forwarding state
br0: port 2(ath0) entered forwarding state
8021q: adding VLAN 0 to HW filter on device ath0
[DEBUG] vap-0(ath1):set SIOC80211NWID, 7 characters
DES SSID SET=asus_5G
Sending SCAN START cmd
br0: topology change detected, propagating
br0: port 3(ath1) entered forwarding state
br0: port 3(ath1) entered forwarding state
8021q: adding VLAN 0 to HW filter on device ath1
ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
[UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=8 6690a10 arg=84860000
osif_vap_stop: Scan in progress.. Cancelling it. vap: 0x84c18000
send_vdev_down_cmd_non_tlv for vap 0
br0: port 3(ath1) entered disabled state
DEVICE IS DOWN ifname=ath1
DEVICE IS DOWN ifname=ath1
Sending SCAN START cmd
br0: topology change detected, propagating
br0: port 3(ath1) entered forwarding state
br0: port 3(ath1) entered forwarding state
8021q: adding VLAN 0 to HW filter on device ath1
[wifi1] FWLOG: [22445] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [22537] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[wifi1] FWLOG: [22537] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[wifi1] FWLOG: [23038] WAL_DBGID_SECURITY_ENCR_EN ( )
[wifi1] FWLOG: [23038] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
[wifi1] FWLOG: [23392] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_o k=1
ieee80211_derive_chan : Overriding HT40 channel with HT20 channel
__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
[wifi1] FWLOG: [23707] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [24021] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [24335] WAL channel change freq=5745, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [24649] WAL channel change freq=5765, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [24963] WAL channel change freq=5785, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [25277] WAL channel change freq=5805, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [25297] WAL_DBGID_BB_WDOG_TRIGGERED ( 0x62d1, 0x13000309, 0x0, 0x 1 )
[wifi1] FWLOG: [25297] WAL_DBGID_BB_WDOG_TRIGGERED ( 0x8000, 0x0 )
[wifi1] FWLOG: [25297] WAL_DBGID_RdOrCrOtCtAgSrHgRdsSsAbFoFbFp ( 0x80838080, 0x8 0838180, 0x80808080, 0x8080 )
send_vdev_down_cmd_non_tlv for vap 0
---- ACS CALCULATE ----
Chan 36 pre_param 0 param 0
Chan 40 pre_param 0 param 0
Chan 44 pre_param 0 param 0
Chan 48 pre_param 0 param 0
Chan 149 pre_param 0 param 0
Chan 153 pre_param 0 param 0
Chan 157 pre_param 0 param 0
Chan 161 pre_param 0 param 0
Selected dot11 channel 36
OL vap_start +
VDEV START
OL vap_start -
ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
ol_vdev_start_resp_ev for vap 0 (pK-error)
send_wmm_update_cmd_non_tlv:
su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
send_vdev_up_cmd_non_tlv for vap 0
Beacon mode set to staggered. Cannot enable FD
__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
[wifi1] FWLOG: [25592] WAL channel change freq=5825, mode=0 flags=0 rx_ok=1 tx_o k=1
[wifi1] FWLOG: [25902] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[wifi1] FWLOG: [25902] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[wifi1] FWLOG: [25933] vap-0 VDEV_MGR_VDEV_START ( 0x143c, 0x2, 0x0, 0x0 )
[wifi1] FWLOG: [25939] WAL channel change freq=5180, mode=10 flags=0 rx_ok=1 tx_ ok=1
[wifi1] FWLOG: [26152] VDEV_MGR_VDEV_START_RESP ( 0x0 )
[wifi1] FWLOG: [26169] VDEV_MGR_HP_START_TIME ( 0x0, 0x143c, 0x1388000 )
[wifi1] FWLOG: [26169] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
[wifi1] FWLOG: [26169] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[wifi1] FWLOG: [26169] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x143c, 0x0, 0x0 )
ol_ath_vap_set_param: Now supported MCAST RATE is 6000(kbps) and rate code: 0x3
nvram_commit(): pid 455 comm [httpd]
found private data block and skip it
nvram_commit(): pid 1 comm [init]
found private data block and skip it
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
--== lsmod ==--
Module Size Used by Tainted: P
nf_nat_sip 5344 0
nf_conntrack_sip 16573 1 nf_nat_sip
nf_nat_h323 4608 0
nf_conntrack_h323 34095 1 nf_nat_h323
nf_nat_rtsp 3216 0
nf_conntrack_rtsp 4073 1 nf_nat_rtsp
nf_nat_ftp 1072 0
nf_conntrack_ftp 4672 1 nf_nat_ftp
ip6table_mangle 992 0
hfsplus 72740 0
hfs 41816 0
vfat 8256 0
fat 44382 1 vfat
ext2 55484 0
ext4 252942 0
jbd2 41787 1 ext4
ext3 112174 0
jbd 35167 1 ext3
mbcache 4132 3 ext2,ext4,ext3
usb_storage 35160 0
sg 19856 0
sd_mod 23088 0
scsi_wait_scan 400 0
cdc_ncm 6768 0
rndis_host 4953 0
cdc_ether 3308 1 rndis_host
asix 11808 0
cdc_acm 11760 0
usbnet 13026 4 cdc_ncm,rndis_host,cdc_ether,asix
shortcut_fe_cm 6021 0
shortcut_fe_ipv6 556561 1 shortcut_fe_cm
shortcut_fe 427441 1 shortcut_fe_cm
ip6t_LOG 6400 0
ip6table_filter 608 1
ohci_hcd 16752 0
ehci_hcd 35088 0
usbcore 108469 10 usb_storage,cdc_ncm,rndis_host,cdc_ether,asix,cdc_acm,usbnet,ohci_hcd,ehci_hcd
usb_common 529 1 usbcore
jffs2 86310 1
nf_nat_pptp 1360 0
nf_conntrack_pptp 3344 1 nf_nat_pptp
nf_nat_proto_gre 912 1 nf_nat_pptp
nf_conntrack_proto_gre 2725 1 nf_conntrack_pptp
qca_ol 971518 0
qca_da 195224 0
ath_dev 283977 1 qca_da
hst_tx99 7652 2 qca_da,ath_dev
ath_rate_atheros 47364 2 qca_da,ath_dev
ath_hal 846982 5 qca_ol,qca_da,ath_dev,hst_tx99,ath_rate_atheros
umac 1545943 4 qca_ol,qca_da,ath_dev,ath_rate_atheros
ath_spectral 31259 3 qca_ol,qca_da,ath_dev
ath_dfs 62657 3 qca_ol,qca_da,umac
qdf 20370 9 qca_ol,qca_da,ath_dev,hst_tx99,ath_rate_atheros,ath_hal,umac,ath_spectral,ath_dfs
asf 6634 7 qca_ol,qca_da,ath_dev,ath_hal,umac,ath_spectral,ath_dfs
mem_manager 5820 2 qca_ol,umac
qca_ssdk 1339137 0
bled 19644 0
nvram_linux 18387 42
--== df -h ==--
Filesystem Size Used Available Use% Mounted on
rootfs 18.5M 18.5M 0 100% /
/dev/root 18.5M 18.5M 0 100% /
tmpfs 61.4M 368.0K 61.1M 1% /tmp
devfs 61.4M 0 61.4M 0% /dev
/dev/mtdblock5 3.0M 336.0K 2.7M 11% /jffs
--== cat /proc/meminfo ==--
MemTotal: 125848 kB
MemFree: 32596 kB
Buffers: 9172 kB
Cached: 26424 kB
SwapCached: 0 kB
Active: 23332 kB
Inactive: 25964 kB
Active(anon): 13896 kB
Inactive(anon): 244 kB
Active(file): 9436 kB
Inactive(file): 25720 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 13716 kB
Mapped: 6192 kB
Shmem: 440 kB
Slab: 22016 kB
SReclaimable: 1552 kB
SUnreclaim: 20464 kB
KernelStack: 656 kB
PageTables: 812 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 62924 kB
Committed_AS: 41276 kB
VmallocTotal: 1048372 kB
VmallocUsed: 760 kB
VmallocChunk: 1034664 kB
The TechInfoDepot specs on the RT-AC59U (version not specified)...
With 16 MB of flash and 128MB of RAM, it's on the lower end of the current requirements for running OpenWRT.
Also, the CPU is 775 MHz.
this is Asus RT-AC59U V2
it has 32MB Flash (from the website)
but df -h it looks like 64MB
I have no idea how to read the df -h
You can always post a request for adding support on the "For Developers" forum.
Might be a rebadged older QCA MIPS SoC:
@hanhan_spm This device is basically the same as v1 except it has more storage. We're working on it in this thread which is the same thread that Borromini pointed to. Expect non-functional 2.4 GHz Wi-Fi for quite some time, everything else will be supported at some point.
Quick summary on models and versions:
16 MiB storage: RT-AC57U v2 == RT-AC58U v2 == RT-AC59U v1
32 MiB storage: RT-AC57U v3 == RT-AC58U v3 == RT-AC59U v2
There's no need to have multiple topics open for the same device.
Therefore please head over to the already existing topic Asus RT-AC59U Support or to the RT-AC57U v2 topic linked above.