Hi Today I compile and install image to TP-Link Archer C9v1
WAN and LAN work OK but wireless not working 2,4 and 5GHz.
\After reboot router not start:
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.32 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2242) ) #0 SMP Sat Nov 19 13:19:27 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: TP-LINK Archer C9 V1
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
[ 0.000000] PERCPU: Embedded 11 pages/cpu @c7eda000 s12928 r8192 d23936 u45056
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 earlycon
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 124568K/131072K available (3318K kernel code, 110K rwdata, 1252K rodata, 228K init, 285K bss, 6504K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[......]
[ 0.586952] bcma: bus0: Flash type not supported
[ 0.592734] m25p80 spi32766.0: s25fl128s (16384 Kbytes)
[ 0.711647] 6 bcm47xxpart partitions found on MTD device spi32766.0
[ 0.717936] Creating 6 MTD partitions on "spi32766.0":
[ 0.723100] 0x000000000000-0x000000040000 : "boot"
[ 0.728757] 0x000000040000-0x000000240000 : "firmware"
[ 0.734725] 0x00000004001c-0x000000240000 : "linux"
[ 0.740356] 0x000000240000-0x000000e40000 : "rootfs"
[ 0.746037] mtd: device 3 (rootfs) set to be root filesystem
[ 0.751774] 1 squashfs-split partitions found on MTD device rootfs
[ 0.757977] 0x0000003c0000-0x000000e40000 : "rootfs_data"
[ 0.764125] 0x000000e40000-0x000000ff0000 : "tplink"
[ 0.769791] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.820228] bgmac_bcma bcma0:3: Found PHY addr: 30 (NOREGS)
[ 0.825823] bgmac_bcma bcma0:3: Support for Roboswitch not implemented
[ 0.834329] b53_common: found switch: BCM53012, rev 5
[ 0.840118] bgmac_bcma bcma0:4: Found PHY addr: 0
[ 0.844852] bgmac_bcma bcma0:4: Support for Roboswitch not implemented
[ 0.851480] bgmac_bcma bcma0:4: Invalid MAC addr: 00:00:00:00:00:00
[ 0.857783] bgmac_bcma bcma0:4: Using random MAC: 0e:d7:db:ac:7f:00
[ 0.865422] bgmac_bcma bcma0:5: Found PHY addr: 0
[ 0.870190] bgmac_bcma bcma0:5: Support for Roboswitch not implemented
[ 0.876799] bgmac_bcma bcma0:5: Invalid MAC addr: 00:00:00:00:00:00
[ 0.883116] bgmac_bcma bcma0:5: Using random MAC: 22:68:cc:fd:ae:d7
[ 0.890733] bgmac_bcma bcma0:6: Unsupported core_unit 3
[ 0.896000] bgmac_bcma: probe of bcma0:6 failed with error -524
[ 1.009639] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00
[ 1.015940] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[ 1.022854] pcie_iproc_bcma bcma0:7: link: UP
[ 1.027448] PCI: bus0: Fast back to back transfers disabled
[ 1.033055] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.041498] PCI: bus1: Fast back to back transfers disabled
[ 1.047139] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
[ 1.053966] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
[ 1.061309] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.066291] pci 0000:00:00.0: bridge window [mem 0x08000000-0x080fffff]
[ 1.179629] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00
[ 1.185921] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff]
[ 1.192830] pcie_iproc_bcma bcma0:8: link: UP
[ 1.197425] PCI: bus0: Fast back to back transfers disabled
[ 1.203026] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.211476] PCI: bus1: Fast back to back transfers disabled
[ 1.217117] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
[ 1.223946] pci 0001:01:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
[ 1.231290] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 1.236272] pci 0001:00:00.0: bridge window [mem 0x40000000-0x400fffff]
[ 1.349626] pcie_iproc_bcma bcma0:9: PCI host bridge to bus 0002:00
[ 1.355918] pci_bus 0002:00: root bus resource [mem 0x48000000-0x4fffffff]
[ 1.362821] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[ 1.369021] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[ 1.375027] pcie_iproc_bcma bcma0:9: PCIe controller setup failed
[ 1.382151] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.391162] bcma: bus0: Bus registered
[ 1.395056] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 1.400751] bcma-pci-bridge 0000:01:00.0: enabling device (0140 -> 0142)
[ 1.407493] bcma: bus1: Found chip with id 0x4360, rev 0x03 and package 0x01
[ 1.414592] bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0)
[ 1.423153] bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0)
[ 1.431813] bcma: bus1: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0)
[ 1.440125] bcma: bus1: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0)
[ 1.448598] bcma: bus1: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[ 1.488992] bcma: bus1: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[ 1.508491] bcma: bus1: Bus registered
[ 1.512322] pci 0001:00:00.0: enabling device (0140 -> 0142)
[ 1.518008] bcma-pci-bridge 0001:01:00.0: enabling device (0140 -> 0142)
[ 1.524762] bcma: bus2: Found chip with id 0x4360, rev 0x03 and package 0x01
[ 1.531860] bcma: bus2: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0)
[ 1.540422] bcma: bus2: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0)
[ 1.549076] bcma: bus2: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0)
[ 1.557387] bcma: bus2: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0)
[ 1.565863] bcma: bus2: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[ 1.606254] bcma: bus2: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[ 1.625316] bcma: bus2: Bus registered
[ 1.630024] NET: Registered protocol family 10
[ 1.635489] NET: Registered protocol family 17
[ 1.640028] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.652688] 8021q: 802.1Q VLAN Support v1.8
[ 1.656953] Registering SWP/SWPB emulation handler
[ 1.668063] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.675402] Freeing unused kernel memory: 228K (c047f000 - c04b8000)
[ 2.201294] init: Console is alive
[ 2.204841] init: - watchdog -
[ 2.464088] usbcore: registered new interface driver usbfs
[ 2.469707] usbcore: registered new interface driver hub
[ 2.475112] usbcore: registered new device driver usb
[ 2.482589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.489779] ehci-platform: EHCI generic platform driver
[ 2.496269] ehci-platform 18021000.ehci: EHCI Host Controller
[ 2.496815] bcm_ns_usb3 18105000.usb3-phy: Registered Broadcom Northstar USB 3.0 PHY driver
[ 2.497857] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.498380] ohci-platform: OHCI generic platform driver
[ 2.498536] ohci-platform 18022000.ohci: Generic Platform OHCI controller
[ 2.498560] ohci-platform 18022000.ohci: new USB bus registered, assigned bus number 1
[ 2.498675] ohci-platform 18022000.ohci: irq 29, io mem 0x18022000
[ 2.542832] ehci-platform 18021000.ehci: new USB bus registered, assigned bus number 2
[ 2.550907] ehci-platform 18021000.ehci: irq 29, io mem 0x18021000
[ 2.554106] hub 1-0:1.0: USB hub found
[ 2.554178] hub 1-0:1.0: 2 ports detected
[ 2.557982] xhci-hcd 18023000.xhci: xHCI Host Controller
[ 2.558010] xhci-hcd 18023000.xhci: new USB bus registered, assigned bus number 3
[ 2.558264] xhci-hcd 18023000.xhci: hcc params 0x02501164 hci version 0x100 quirks 0x01010010
[ 2.558304] xhci-hcd 18023000.xhci: irq 30, io mem 0x18023000
[ 2.559072] hub 3-0:1.0: USB hub found
[ 2.559154] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 2.559313] xhci-hcd 18023000.xhci: xHCI Host Controller
[ 2.559328] xhci-hcd 18023000.xhci: new USB bus registered, assigned bus number 4
[ 2.569625] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.570209] hub 4-0:1.0: USB hub found
[ 2.570287] hub 4-0:1.0: 1 port detected
[ 2.579703] init: - preinit -
[ 2.649644] ehci-platform 18021000.ehci: USB 2.0 started, EHCI 1.00
[ 2.657215] hub 2-0:1.0: USB hub found
[ 2.709611] hub 2-0:1.0: 2 ports detected
[ 2.979906] random: jshn: uninitialized urandom read (4 bytes read, 0 bits of entropy available)
[ 3.040399] random: jshn: uninitialized urandom read (4 bytes read, 0 bits of entropy available)
[ 3.074231] random: jshn: uninitialized urandom read (4 bytes read, 0 bits of entropy available)
[ 3.233248] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.239187] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 3.264240] random: procd: uninitialized urandom read (4 bytes read, 0 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 4.839565] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[ 4.846924] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4.853434] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 6.402265] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 6.411993] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.494001] procd: - early -
[ 6.496947] procd: - watchdog -
[ 7.109747] procd: - ubus -
[ 7.170052] random: ubusd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
[ 7.179141] random: ubusd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
[ 7.188112] random: ubusd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
[ 7.197246] random: ubusd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
[ 7.206207] random: ubusd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
[ 7.215226] random: ubusd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
[ 7.224420] procd: - init -
Please press Enter to activate this console.
[ 7.307646] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.319272] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.328709] nf_conntrack version 0.5.0 (1949 buckets, 7796 max)
[ 7.428768] xt_time: kernel timezone is -0000
[ 7.438151] PPP generic driver version 2.4.2
[ 7.443373] NET: Registered protocol family 24
[ 11.167105] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 11.174095] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 11.180771] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 11.332270] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.374528] device eth0.1 entered promiscuous mode
[ 11.379345] device eth0 entered promiscuous mode
[ 11.401436] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 11.433236] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 11.839650] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[ 11.860080] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.866932] br-lan: port 1(eth0.1) entered forwarding state
[ 11.872570] br-lan: port 1(eth0.1) entered forwarding state
[ 11.878530] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 11.891338] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 13.869531] br-lan: port 1(eth0.1) entered forwarding state
[ 34.072481] done.
[ 34.074437] jffs2: notice: (895) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
BusyBox v1.25.1 () built-in shell (ash)
_________ / /\ _ ___ ___ ___/ LE / \ | | | | | |
/ DE / \ | || _|| |) | _|
/_/ LE \ |||/|| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (HEAD, r2242)
________/ -----------------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.root@lede:/# [ 137.126566] random: nonblocking pool is initialized
reboot
root@lede:/# [ 138.188727] br-lan: port 1(eth0.1) entered disabled state
[ 138.198068] device eth0.1 left promiscuous mode
[ 138.202687] device eth0 left promiscuous mode
[ 138.207172] br-lan: port 1(eth0.1) entered disabled state
[ 138.213859] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 142.610810] reboot: Restarting system
After reboot:
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.32 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2242) ) #0 SMP Sat Nov 19 13:19:27 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: TP-LINK Archer C9 V1
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
[ 0.000000] PERCPU: Embedded 11 pages/cpu @c7eda000 s12928 r8192 d23936 u45056
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 earlycon
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 124568K/131072K available (3318K kernel code, 110K rwdata, 1252K rodata, 228K init, 285K bss, 6504K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc047ee44 (4572 kB)
[ 0.000000] .init : 0xc047f000 - 0xc04b8000 ( 228 kB)
[ 0.000000] .data : 0xc04b8000 - 0xc04d3848 ( 111 kB)
[ 0.000000] .bss : 0xc04d3848 - 0xc051aff8 ( 286 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x0a530000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001
[....]
[ 0.597211] bcma: bus0: Flash type not supported
[ 0.603032] m25p80 spi32766.0: s25fl128s (16384 Kbytes)
[ 0.718004] 5 bcm47xxpart partitions found on MTD device spi32766.0
[ 0.724298] Creating 5 MTD partitions on "spi32766.0":
[ 0.729455] 0x000000000000-0x000000040000 : "boot"
[ 0.735213] 0x000000040000-0x000000e40000 : "firmware"
[ 0.741138] 0x00000004001c-0x000000e40000 : "linux"
[ 0.746706] 0x000000e40000-0x000000ff0000 : "tplink"
[ 0.752431] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.802846] bgmac_bcma bcma0:3: Found PHY addr: 30 (NOREGS)
[ 0.808447] bgmac_bcma bcma0:3: Support for Roboswitch not implemented
[ 0.816953] b53_common: found switch: BCM53012, rev 5
[ 0.822729] bgmac_bcma bcma0:4: Found PHY addr: 0
[ 0.827456] bgmac_bcma bcma0:4: Support for Roboswitch not implemented
[ 0.834079] bgmac_bcma bcma0:4: Invalid MAC addr: 00:00:00:00:00:00
[ 0.840390] bgmac_bcma bcma0:4: Using random MAC: ce:9f:e4:83:59:97
[ 0.847993] bgmac_bcma bcma0:5: Found PHY addr: 0
[ 0.852767] bgmac_bcma bcma0:5: Support for Roboswitch not implemented
[ 0.859383] bgmac_bcma bcma0:5: Invalid MAC addr: 00:00:00:00:00:00
[ 0.865698] bgmac_bcma bcma0:5: Using random MAC: 12:12:51:21:38:85
[ 0.873316] bgmac_bcma bcma0:6: Unsupported core_unit 3
[ 0.878587] bgmac_bcma: probe of bcma0:6 failed with error -524
[ 0.989521] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00
[ 0.995821] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[ 1.002734] pcie_iproc_bcma bcma0:7: link: UP
[ 1.007323] PCI: bus0: Fast back to back transfers disabled
[ 1.012927] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.021365] PCI: bus1: Fast back to back transfers disabled
[ 1.027008] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
[ 1.033836] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
[ 1.041180] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.046162] pci 0000:00:00.0: bridge window [mem 0x08000000-0x080fffff]
[ 1.159510] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00
[ 1.165801] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff]
[ 1.172712] pcie_iproc_bcma bcma0:8: link: UP
[ 1.177300] PCI: bus0: Fast back to back transfers disabled
[ 1.182907] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.191340] PCI: bus1: Fast back to back transfers disabled
[ 1.196981] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
[ 1.203807] pci 0001:01:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
[ 1.211150] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 1.216134] pci 0001:00:00.0: bridge window [mem 0x40000000-0x400fffff]
[ 1.329509] pcie_iproc_bcma bcma0:9: PCI host bridge to bus 0002:00
[ 1.335807] pci_bus 0002:00: root bus resource [mem 0x48000000-0x4fffffff]
[ 1.342711] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[ 1.348910] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[ 1.354915] pcie_iproc_bcma bcma0:9: PCIe controller setup failed
[ 1.362062] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.371077] bcma: bus0: Bus registered
[ 1.374964] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 1.380659] bcma-pci-bridge 0000:01:00.0: enabling device (0140 -> 0142)
[ 1.387401] bcma: bus1: Found chip with id 0x4360, rev 0x03 and package 0x01
[ 1.394499] bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0)
[ 1.403059] bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0)
[ 1.411727] bcma: bus1: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0)
[ 1.420041] bcma: bus1: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0)
[ 1.428513] bcma: bus1: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[ 1.468905] bcma: bus1: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[ 1.488382] bcma: bus1: Bus registered
[ 1.492211] pci 0001:00:00.0: enabling device (0140 -> 0142)
[ 1.497898] bcma-pci-bridge 0001:01:00.0: enabling device (0140 -> 0142)
[ 1.504648] bcma: bus2: Found chip with id 0x4360, rev 0x03 and package 0x01
[ 1.511748] bcma: bus2: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0)
[ 1.520311] bcma: bus2: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0)
[ 1.528965] bcma: bus2: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0)
[ 1.537275] bcma: bus2: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0)
[ 1.545752] bcma: bus2: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[ 1.586138] bcma: bus2: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[ 1.605189] bcma: bus2: Bus registered
[ 1.609908] NET: Registered protocol family 10
[ 1.615370] NET: Registered protocol family 17
[ 1.619908] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.632567] 8021q: 802.1Q VLAN Support v1.8
[ 1.636833] Registering SWP/SWPB emulation handler
[ 1.644108] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.651645] Please append a correct "root=" boot option; here are the available partitions:
[ 1.660037] 1f00 256 mtdblock0 (driver?)
[ 1.665113] 1f01 14336 mtdblock1 (driver?)
[ 1.670192] 1f02 14335 mtdblock2 (driver?)
[ 1.675260] 1f03 1728 mtdblock3 (driver?)
[ 1.680340] 1f04 64 mtdblock4 (driver?)
[ 1.685410] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 1.693694] CPU0: stopping
[ 1.696413] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.32 #0
[ 1.702343] Hardware name: BCM5301X
[ 1.705833] Backtrace:
[ 1.708314] [] (dump_backtrace) from [] (show_stack+0x18/0x1c)
[ 1.715896] r7:c04b9f20 r6:00000000 r5:60000193 r4:00000000
[ 1.721612] [] (show_stack) from [] (dump_stack+0x84/0xa4)
[ 1.728855] [] (dump_stack) from [] (handle_IPI+0xf4/0x19c)
[ 1.736175] r5:00000000 r4:c04d39e8
[ 1.739777] [] (handle_IPI) from [] (gic_handle_irq+0x80/0x9c)
[ 1.747360] r7:c04c55ac r6:c04b9f20 r5:c04ba708 r4:c8802100
[ 1.753067] [] (gic_handle_irq) from [] (__irq_svc+0x54/0x70)
[ 1.760565] Exception stack(0xc04b9f20 to 0xc04b9f68)
[ 1.765627] 9f20: 00000000 00000516 c7eda254 c000ae40 c04b3224 c04ba498 c04ba3c0 c04d3894
[ 1.773825] 9f40: c7ffe880 c04a8a28 c04d3890 c04b9f7c c04b9f80 c04b9f70 c0014638 c001463c
[ 1.782021] 9f60: 60000013 ffffffff
[ 1.785510] r9:c04a8a28 r8:c7ffe880 r7:c04b9f54 r6:ffffffff r5:60000013 r4:c001463c
[ 1.793321] [] (arch_cpu_idle) from [] (default_idle_call+0x30/0x34)
[ 1.801436] [] (default_idle_call) from [] (cpu_startup_entry+0x130/0x194)
[ 1.810078] [] (cpu_startup_entry) from [] (rest_init+0x6c/0x84)
[ 1.817857] [] (rest_init) from [] (start_kernel+0x370/0x3f0)
[ 1.825362] [] (start_kernel) from [<0000807c>] (0x807c)
[ 1.831554] r10:00000000 r9:413fc090 r8:0000406a r7:c04bcdd4 r6:c04a8a24 r5:c04ba444
[ 1.839439] r4:c04d39a0
[ 1.842760] Rebooting in 1 seconds..