Is it possible that 2.4GHz wifi is using the wrong circuit?
MT7612 Wi-Fi Frequency: 2.4GHz, 5GHz
MT7628 Wi-Fi Freqency: 2.4GHz (antennas are connected here)
2 Likes
Experiencing the same here, with an EU edition, also had stock firmware with 2.4GHz performance absolutely fine before, unit in the same location, stock firmware was latest and greatest, openwrt is 19.07.3. Tried all suggestions here, to no avail!
low signal 2.4 ghz on my c50 v4 EU
i bought this router because it's supported
why not mention the low signal problem in wiki
The wiki does mention this for the v4. It references this forum thread.
1 Like
i see it now ... my eyes has low signal too 
is there a chance to fix this problem ? i read c50 v3 has the same problem wich is solved by flashing 18.06.8 ... I think this hardware with stable release can do great performance
Minor and unimportant update:
Bought EU v4.20 version and the 2.4GHz problem persists with latest build.
Too bad 
1 Like
same thing here i bought this device too i didn't realize the notification about low signal in the wiki ...
same thing here
I've got 6 of these Archer C50 v4.{0,1,2} devices, 2 of them working fine with OpenWrt, the others have the low signal problem with identical firmware.
After digging into the problem I found there is a difference in the contents of the eeprom partition /dev/mtd9. The first two bytes in the eeprom are the chip id. The working devices have 0x7628 there, whereas the non-working devices have 0x7600 there. This chip id gets checked by the function mt7603_check_eeprom() which leads the driver to ignore the contents of the eeprom partition and load default values from otp.
After patching the driver to also accept 0x7600 as valid chip id, all of my devices are working fine.
What is the right way to submit a patch for mt76 driver?
8 Likes
Perhaps report your findings in original bug report 2781, and hope a developer will pick it up and submit the fix for you:
https://bugs.openwrt.org/index.php?do=details&task_id=2781
1 Like
Please submit that patch, the 2.4 GHz is terrible.
1 Like
I submitted a pull request on https://github.com/openwrt/mt76 but I'm not sure I did it correctly. Could you have a look/comment on the pull request?
1 Like
@dtrautmann Would you mind taking some more time outline the steps to you took to patch the driver so I and other can duplicate your work? Or provide instruction on how to use the patched driver?
Thank You.
1 Like
Thank you for the patch. Once the patch is merged, is there any possibility of the pre built image for c50 v4 ?
To build your OpenWrt image including the patched driver, download the patch from https://github.com/openwrt/mt76/pull/442.patch and copy it to the directory packages/kernel/mt76/patches of your OpenWrt source.
Then rebuild the image.
4 Likes
Eventually worked out how to build a new version as above, and is now working perfectly for me 
Wonderful to hear @VintageRain. I haven’t found the time to apply it myself. Hope it will make it in the next release so others avoid the issue.
Would you mind sharing your compiled patched version? I've been trying all day without succes. It'd be very nice of you or anyone who can share a patched version of the kmod or the firmware.
Yep I can do that... I'll share a link. Bear in mind this is for the v4, is based on 19.07.4 and I can't accept any responsibility etc etc 
But I wish you luck! I just uploaded this using the LuCI web portal..
https://mega.nz/file/ZEwz2IhB#S-nb5UfDJRUUyuEIRvh9MfPj4pUTlXAV_RblBlJezKM
4 Likes
Thank you very much. You've really made my day 
It worked well as expected for my Archer C50 v4
1 Like