hey frollic, thank you for everything….
Well, now a new issue showed up ... The router will boot with USB and I use the same new version 24.10 for SysupGrade, ok… but after uploading and installation, router doesn't boot like before(with usb) ... that is, it doesn't save anything from these operations.(No changes to settings will be stored and are lost after rebooting)
Just to clarify , you booted the router from USB, installed the OpenWrt sysupgrade file via webui, removed the USB, and then rebooted, but now the router isn’t booting or something? 
You mentioned that no settings are saved and everything resets after a reboot, that suggests there could be a problem with the storage🤔
If you didn’t remove the USB before rebooting, the router will boot from the USB again, no matter what firmware is installed on the router. And any settings you save won’t actually be saved. Remove the USB first, then power off or reboot, and power it on again.
Are there any LED lights on? What colors and which LEDs exactly?Can you connect to the router using a LAN cable?
And also, did you follow the Expanded MTD layout guide? If you did, then you’ll need to set up USB boot again.But since you said OpenWrt flashed successfully, it should boot without any issues now.
yeah exactly…. 
true…
alright, will do it again … 
yes, just power ⛮ led…. it's green like before… no led are turned on except that ... yes, almost…
If the TTL to USB connection isn't done correctly, it will not show you any log ...I have been working with it for a few months now ...
first boot without using usb flash
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
[do_boot_unsignedimg(887)] debug:0
setenv - set environment variables
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
IPQ807x#
and now want to do it again >>>>>>>>>>
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 3446 - bootable_media_detect_success, Start
B - 3451 - elf_loader_entry, Start
B - 7619 - auth_hash_seg_entry, Start
B - 7864 - auth_hash_seg_exit, Start
B - 69641 - elf_segs_hash_verify_entry, Start
B - 132483 - PBL, End
B - 145088 - SBL1, Start
B - 197426 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 203953 - pm_device_init, Start
B - 326228 - PM_SET_VAL:Skip
D - 121756 - pm_device_init, Delta
B - 328637 - pm_driver_init, Start
D - 5337 - pm_driver_init, Delta
B - 334951 - clock_init, Start
D - 2104 - clock_init, Delta
B - 338946 - boot_flash_init, Start
D - 16561 - boot_flash_init, Delta
B - 359259 - boot_config_data_table_init, Start
D - 3995 - boot_config_data_table_init, Delta - (575 Bytes)
B - 366640 - Boot Setting : 0x00000618
B - 370758 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 377590 - sbl1_ddr_set_params, Start
B - 381402 - CPR configuration: 0x30c
B - 384849 - cpr_init, Start
B - 387624 - Rail:0 Mode: 5 Voltage: 792000
B - 392840 - CL CPR settled at 744000mV
B - 395676 - Rail:1 Mode: 5 Voltage: 880000
B - 399855 - Rail:1 Mode: 7 Voltage: 896000
D - 16531 - cpr_init, Delta
B - 406748 - Pre_DDR_clock_init, Start
B - 410774 - Pre_DDR_clock_init, End
B - 414068 - DDR Type : PCDDR3
B - 419832 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 424590 - DDR: Start of HAL DDR Boot Training
B - 429318 - DDR: End of HAL DDR Boot Training
B - 434991 - DDR: Checksum to be stored on flash is 1789927307
B - 445330 - Image Load, Start
D - 215940 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 661362 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 669048 - Image Load, Start
D - 11986 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 681126 - Image Load, Start
D - 23058 - RPM Image Loaded, Delta - (86584 Bytes)
B - 704275 - Image Load, Start
D - 88724 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 793091 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 798886 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 805291 - SBL1, End
D - 662491 - SBL1, Delta
S - Flash Throughput, 6903 KB/s (2053791 Bytes, 297521 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
[do_boot_unsignedimg(887)] debug:0
setenv - set environment variables
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# setenv bootusb 'usb start && usbboot 0x44000000 0 && bootm 0x44000000'
IPQ807x# setenv bootcmd 'run bootusb; bootipq'
IPQ807x# saveenv
Saving Environment to NAND...
Erasing NAND...
Erasing at 0xd40000 -- 100% complete.
Writing to NAND... OK
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x#
After a few attempts and reseting the router >>>>>>>
After a few attempts and reseting the router >>>>>>>
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2734 - bootable_media_detect_entry, Start
B - 3446 - bootable_media_detect_success, Start
B - 3450 - elf_loader_entry, Start
B - 7622 - auth_hash_seg_entry, Start
B - 7867 - auth_hash_seg_exit, Start
B - 69693 - elf_segs_hash_verify_entry, Start
B - 132534 - PBL, End
B - 216580 - SBL1, Start
B - 294386 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 304085 - pm_device_init, Start
B - 486109 - PM_SET_VAL:Skip
D - 180163 - pm_device_init, Delta
B - 488518 - pm_driver_init, Start
D - 5337 - pm_driver_init, Delta
B - 494893 - clock_init, Start
D - 2104 - clock_init, Delta
B - 498888 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 519110 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 526491 - Boot Setting : 0x00000618
B - 530608 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 537410 - sbl1_ddr_set_params, Start
B - 541222 - CPR configuration: 0x30c
B - 544699 - cpr_init, Start
B - 547475 - Rail:0 Mode: 5 Voltage: 792000
B - 552690 - CL CPR settled at 744000mV
B - 555496 - Rail:1 Mode: 5 Voltage: 880000
B - 559705 - Rail:1 Mode: 7 Voltage: 896000
D - 16561 - cpr_init, Delta
B - 566568 - Pre_DDR_clock_init, Start
B - 570594 - Pre_DDR_clock_init, End
B - 573888 - DDR Type : PCDDR3
B - 579652 - do ddr sanity test, Start
D - 1037 - do ddr sanity test, Delta
B - 584410 - DDR: Start of HAL DDR Boot Training
B - 589138 - DDR: End of HAL DDR Boot Training
B - 594841 - DDR: Checksum to be stored on flash is 1789927307
B - 605242 - Image Load, Start
D - 215909 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 821243 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 828929 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 841037 - Image Load, Start
D - 23028 - RPM Image Loaded, Delta - (86584 Bytes)
B - 864156 - Image Load, Start
D - 88694 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 952972 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 958767 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 965172 - SBL1, End
D - 750910 - SBL1, Delta
S - Flash Throughput, 6903 KB/s (2053791 Bytes, 297519 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... cannot reset port 1!?
2 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
Loading from usb device 0, partition 0: Name: Whole Disk Type: U-Boot
Fit image detected...
FIT description: ARM64 OpenWrt FIT (Flattened Image Tree)
Image 0 (kernel-1)
Description: ARM64 OpenWrt Linux-6.6.104
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 13293044 Bytes = 12.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: d3522b67
Hash algo: sha1
Hash value: 026459c92f0fb956e513faff5119b8893388fb8a
Image 1 (fdt-1)
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44cad81c
Data Size: 45589 Bytes = 44.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: a5a6c97f
Hash algo: sha1
Hash value: 60c14d260a80884c3acb5353804d7cb04703543e
Default Configuration: 'config@hk09'
Configuration 0 (config@hk09)
Description: OpenWrt arcadyan_aw1000
Kernel: kernel-1
FDT: fdt-1
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.104
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 13293044 Bytes = 12.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: d3522b67
Hash algo: sha1
Hash value: 026459c92f0fb956e513faff5119b8893388fb8a
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44cad81c
Data Size: 45589 Bytes = 44.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: a5a6c97f
Hash algo: sha1
Hash value: 60c14d260a80884c3acb5353804d7cb04703543e
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x44cad81c
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f1000, end 4a3ff214 ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.104 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28872-daca7c049b) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Fri Sep 19 21:19:38 2025
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000
[ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000
[ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000
[ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000
[ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000
[ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
[ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000
[ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 18 pages/cpu s36136 r8192 d29400 u73728
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[ 0.000000] Memory: 877964K/1048576K available (8640K kernel code, 922K rwdata, 1660K rodata, 9536K init, 293K bss, 170612K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: 0xffffffc080010000
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000124] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000138] pid_max: default: 32768 minimum: 301
[ 0.005100] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.005114] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.009394] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.009623] rcu: Hierarchical SRCU implementation.
[ 0.009628] rcu: Max phase no-delay instances is 1000.
[ 0.010531] smp: Bringing up secondary CPUs ...
[ 0.011204] Detected VIPT I-cache on CPU1
[ 0.011308] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.011989] Detected VIPT I-cache on CPU2
[ 0.012059] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.012724] Detected VIPT I-cache on CPU3
[ 0.012791] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.012862] smp: Brought up 1 node, 4 CPUs
[ 0.012870] SMP: Total of 4 processors activated.
[ 0.012875] CPU features: detected: 32-bit EL0 Support
[ 0.012880] CPU features: detected: CRC32 instructions
[ 0.012940] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.012946] CPU: All CPU(s) started at EL1
[ 0.012949] alternatives: applying system-wide alternatives
[ 0.023847] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.023874] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.025602] pinctrl core: initialized pinctrl subsystem
[ 0.027656] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.028346] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.028385] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.028420] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.028842] thermal_sys: Registered thermal governor 'step_wise'
[ 0.028901] cpuidle: using governor menu
[ 0.029199] ASID allocator initialised with 65536 entries
[ 0.056067] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.058928] Modules: 27456 pages in range for non-PLT usage
[ 0.058937] Modules: 518976 pages in range for PLT usage
[ 0.062628] SCSI subsystem initialized
[ 0.062846] usbcore: registered new interface driver usbfs
[ 0.062889] usbcore: registered new interface driver hub
[ 0.062941] usbcore: registered new device driver usb
[ 0.063405] qcom_scm: convention: smc arm 64
[ 0.065212] clocksource: Switched to clocksource arch_sys_counter
[ 0.069155] NET: Registered PF_INET protocol family
[ 0.069299] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.072177] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.072203] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.072218] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.072305] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.072579] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.073082] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[ 0.073255] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.073293] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.073628] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.073679] PCI: CLS 0 bytes, default 64
[ 0.087879] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.088621] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.088627] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.092552] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.096376] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.096576] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.097557] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.097697] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.098838] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator
[ 0.098974] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.099056] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.099235] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.099465] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.099575] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.099615] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.099800] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.102180] gpio-export gpio-export: 4 gpio(s) exported
[ 0.109413] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.113484] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.113529] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.113915] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.113951] msm_serial: console setup on port #0
[ 0.113994] printk: console [ttyMSM0] enabled
[ 0.967653] msm_serial: driver initialized
[ 0.977245] loop: module loaded
[ 0.978533] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 0.979203] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 0.985819] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.002304] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 1.106765] i2c_dev: i2c /dev entries driver
[ 1.113142] sdhci: Secure Digital Host Controller Interface driver
[ 1.113182] sdhci: Copyright(c) Pierre Ossman
[ 1.118257] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.124624] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 1.132065] NET: Registered PF_INET6 protocol family
[ 1.135400] Segment Routing with IPv6
[ 1.139263] In-situ OAM (IOAM) with IPv6
[ 1.142885] NET: Registered PF_PACKET protocol family
[ 1.146882] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.151972] 8021q: 802.1Q VLAN Support v1.8
[ 1.196454] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 1.196815] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.202583] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.209202] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.216851] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.224348] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.233493] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.240441] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 816000 uV
[ 1.250423] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 880000 uV
[ 1.260231] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 960000 uV
[ 1.270089] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 746, quot_offset[ 7]= 0
[ 1.279853] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 964, quot_offset[ 7]= 215
[ 1.290703] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1076, quot_offset[ 7]= 110
[ 1.301640] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1224, quot_offset[ 7]= 145
[ 1.312787] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.315329] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 1.330471] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 1.336720] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.351860] 26 qcomsmem partitions found on MTD device qcom_nand.0
[ 1.351910] Creating 26 MTD partitions on "qcom_nand.0":
[ 1.357007] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.363532] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.368308] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.373023] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.378400] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.384867] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.390160] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.394005] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.399210] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.404664] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.409603] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.414540] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.419340] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.424514] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.429246] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.434433] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.440083] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.445053] 0x000000f80000-0x000001000000 : "0:art"
[ 1.450341] 0x000001000000-0x000007400000 : "rootfs"
[ 1.496449] mtd: setting mtd18 (rootfs) as root device
[ 1.496978] mtdsplit: no squashfs found in "rootfs"
[ 1.500524] 0x000007400000-0x000008c80000 : "0:wififw"
[ 1.515995] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 1.558116] 0x00000f080000-0x000010900000 : "0:wififw_1"
[ 1.568915] 0x000010900000-0x000010b40000 : "0:ethphyfw"
[ 1.570412] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 1.574216] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 1.582491] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 1.893793] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 1.895650] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 1.903786] ubi0: attaching mtd18
[ 2.319776] ubi0: scanning is finished
[ 2.326209] ubi0: attached mtd18 (name "rootfs", size 100 MiB)
[ 2.326251] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 2.330941] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 2.337818] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 2.344656] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 2.351434] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.357686] ubi0: max/mean erase counter: 72/45, WL threshold: 4096, image sequence number: 308896951
[ 2.364714] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
[ 2.374024] ubi0: background thread "ubi_bgt0d" started, PID 709
[ 2.375020] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.389298] ubi: mtd18 is already attached to ubi0
[ 2.394565] UBI error: cannot attach mtd18
[ 2.399349] ubi: mtd18 is already attached to ubi0
[ 2.403419] UBI error: cannot attach ▒[ 2.415857] Freeing unused kernel memory: 9536K
[ 2.416069] Run /init as init process
[ 2.626748] init: Console is alive
[ 2.626882] init: - watchdog -
[ 2.634535] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.647432] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.658423] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist
[ 3.785288] regi_init[2525]:INFO:Initializing HPPE Done!!
[ 3.785424] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[ 3.791709] EDMA ver 1 hw init
[ 3.796000] EDMA HW Reset completed succesfully
[ 3.798646] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 3.803042] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 3.808686] dp1: ppe offload disabled: 0 for macid 1
[ 3.812418] dp1: Switch attached to macid 1 status: 0
[ 3.985996] Qualcomm QCA8075 90000.mdio-1:00: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:00, irq=POLL)
[ 3.986894] dp2: ppe offload disabled: 0 for macid 2
[ 3.994885] dp2: Switch attached to macid 2 status: 0
[ 4.075562] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL)
[ 4.076448] dp3: ppe offload disabled: 0 for macid 3
[ 4.084455] dp3: Switch attached to macid 3 status: 0
[ 4.165571] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL)
[ 4.166488] dp4: ppe offload disabled: 0 for macid 4
[ 4.174478] dp4: Switch attached to macid 4 status: 0
[ 4.255551] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[ 4.256456] dp6-syn: ppe offload disabled: 0 for macid 6
[ 4.264446] dp6-syn: Switch attached to macid 6 status: 0
[ 4.367261] Qualcomm QCA8081 90000.mdio-1:1c: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:1c, irq=POLL)
[ 4.368116] **********************************************************
[ 4.376175] * NSS Data Plane driver
[ 4.382658] **********************************************************
[ 4.402049] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.402098] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 4.406598] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.414029] xhci-hcd xhci-hcd.1.auto: irq 41, io mem 0x08a00000
[ 4.423457] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.429280] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 4.434823] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.442798] hub 1-0:1.0: USB hub found
[ 4.448992] hub 1-0:1.0: 1 port detected
[ 4.452936] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.457247] hub 2-0:1.0: USB hub found
[ 4.464864] hub 2-0:1.0: 1 port detected
[ 4.468831] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.472498] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[ 4.477955] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.485387] xhci-hcd xhci-hcd.2.auto: irq 42, io mem 0x08c00000
[ 4.494796] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.500625] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[ 4.506189] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 4.514141] hub 3-0:1.0: USB hub found
[ 4.520366] hub 3-0:1.0: 1 port detected
[ 4.524348] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.528451] hub 4-0:1.0: USB hub found
[ 4.536227] hub 4-0:1.0: 1 port detected
[ 4.541455] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.548516] init: - preinit -
[ 4.925207] random: crng init done
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.565272] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 8.165405] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 9.093129] nss-dp 3a001000.dp1 lan1: PHY Link is down
[ 9.096912] procd: - early -
[ 9.097237] procd: - watchdog -
[ 9.627513] procd: - watchdog -
[ 9.627756] procd: - ubus -
[ 9.781458] procd: - init -
Please press Enter to activate this console.
[ 9.912280] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.991732] usbcore: registered new interface driver cdc_wdm
[ 9.992067] Loading modules backported from Linux version v6.12.44-0-g11a24528d080
[ 9.996476] Backport generated by backports.git v6.1.110-1-35-g410656ef
[ 10.008087] NET: Registered PF_QIPCRTR protocol family
[ 10.016343] usbcore: registered new interface driver usbserial_generic
[ 10.016403] usbserial: USB Serial support registered for generic
[ 10.057912] PPP generic driver version 2.4.2
[ 10.059013] NET: Registered PF_PPPOX protocol family
[ 10.062147] usbcore: registered new interface driver qmi_wwan
[ 10.070756] urngd: v1.0.2 started.
[ 10.085586] ath11k c000000.wifi: ipq8074 hw2.0
[ 10.085628] ath11k c000000.wifi: FW memory mode: 0
[ 10.227662] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 10.227781] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 10.579251] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 10.623211] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 10.630682] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 soc_id 0xffffffff
[ 10.630718] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 10.945341] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 15.776023] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss
[ 15.776066] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 15.782206] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 16.132230] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 16.133932] usbcore: registered new interface driver option
[ 16.138766] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.144153] option 4-1:1.0: GSM modem (1-port) converter detected
[ 16.151095] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 16.157402] option 4-1:1.1: GSM modem (1-port) converter detected
[ 16.164200] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 16.170253] option 4-1:1.2: GSM modem (1-port) converter detected
[ 16.175931] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 16.177029] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 16.188467] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 soc_id 0xffffffff
[ 16.189160] option 4-1:1.3: GSM modem (1-port) converter detected
[ 16.195864] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 16.204566] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB3
[ 16.225379] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.498593] ath11k c000000.wifi: htt event 48 not handled
[ 21.907865] br-lan: port 1(lan1) entered blocking state
[ 21.907909] br-lan: port 1(lan1) entered disabled state
[ 21.911950] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
[ 21.917477] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
[ 21.929416] br-lan: port 2(lan2) entered blocking state
[ 21.929459] br-lan: port 2(lan2) entered disabled state
[ 21.934082] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
[ 21.939573] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
[ 21.949756] br-lan: port 3(lan3) entered blocking state
[ 21.951057] br-lan: port 3(lan3) entered disabled state
[ 21.956290] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
[ 21.961618] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
[ 21.971045] br-lan: port 4(lan4) entered blocking state
[ 21.973192] br-lan: port 4(lan4) entered disabled state
[ 21.978449] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
[ 21.983744] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
[ 25.045612] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 25.045667] br-lan: port 1(lan1) entered blocking state
[ 25.050349] br-lan: port 1(lan1) entered forwarding state
[ 32.485250] l11: disabling
now, checking in with WebUI (interface) >>>>>>>>>>>>>>>>>
01
02
03
04
05
06
07
logs while performing Sysupgrad >>>>>>>>>>>>>>>>>>>>
Watchdog handover: fd=3
- watchdog -
Watchdog did not previously reset the system
Thu Jan 1 00:07:53 UTC 1970 upgrade: Sending TERM to remaining processes ...
Thu Jan 1 00:07:57 UTC 1970 upgrade: Sending KILL to remaining processes ...
[ 483.361024] stage2 (3976): drop_caches: 3
Thu Jan 1 00:08:03 UTC 1970 upgrade: Switching to ramdisk...
Thu Jan 1 00:08:04 UTC 1970 upgrade: Performing system upgrade...
verifying sysupgrade tar file integrity
[ 484.955362] block ubiblock0_1: released
Volume ID 0, size 21 LEBs (5332992 bytes, 5.0 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "kernel", alignment 1
[ 485.216289] block ubiblock0_1: created from ubi0:1(rootfs)
Volume ID 1, size 30 LEBs (7618560 bytes, 7.2 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 67297280
Volume ID 2, size 265 LEBs (67297280 bytes, 64.1 MiB), LEB size 253952 bytes (24 8.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 487.730707] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcs s
[ 488.205458] reboot: Restarting system
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2736 - bootable_media_detect_entry, Start
B - 3449 - bootable_media_detect_success, Start
B - 3453 - elf_loader_entry, Start
B - 7632 - auth_hash_seg_entry, Start
B - 7877 - auth_hash_seg_exit, Start
B - 69791 - elf_segs_hash_verify_entry, Start
B - 132633 - PBL, End
B - 222436 - SBL1, Start
B - 303200 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 313265 - pm_device_init, Start
B - 496906 - PM_SET_VAL:Skip
D - 181627 - pm_device_init, Delta
B - 499315 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 505690 - clock_init, Start
D - 2135 - clock_init, Delta
B - 509624 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 529937 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 537318 - Boot Setting : 0x00000618
B - 541436 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 548237 - sbl1_ddr_set_params, Start
B - 552050 - CPR configuration: 0x30c
B - 555527 - cpr_init, Start
B - 558302 - Rail:0 Mode: 5 Voltage: 792000
B - 563518 - CL CPR settled at 744000mV
B - 566324 - Rail:1 Mode: 5 Voltage: 880000
B - 570533 - Rail:1 Mode: 7 Voltage: 896000
D - 16531 - cpr_init, Delta
B - 577395 - Pre_DDR_clock_init, Start
B - 581421 - Pre_DDR_clock_init, End
B - 584715 - DDR Type : PCDDR3
B - 590480 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 595238 - DDR: Start of HAL DDR Boot Training
B - 599965 - DDR: End of HAL DDR Boot Training
B - 605638 - DDR: Checksum to be stored on flash is 1789927307
B - 616039 - Image Load, Start
D - 216001 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 832131 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 839817 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 851926 - Image Load, Start
D - 23027 - RPM Image Loaded, Delta - (86584 Bytes)
B - 875045 - Image Load, Start
D - 88724 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 963891 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 969686 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 976091 - SBL1, End
D - 755943 - SBL1, Delta
S - Flash Throughput, 6903 KB/s (2053791 Bytes, 297487 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... cannot reset port 1!?
2 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
Loading from usb device 0, partition 0: Name: Whole Disk Type: U-Boot
Fit image detected...
FIT description: ARM64 OpenWrt FIT (Flattened Image Tree)
Image 0 (kernel-1)
Description: ARM64 OpenWrt Linux-6.6.104
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 13293044 Bytes = 12.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: d3522b67
Hash algo: sha1
Hash value: 026459c92f0fb956e513faff5119b8893388fb8a
Image 1 (fdt-1)
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44cad81c
Data Size: 45589 Bytes = 44.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: a5a6c97f
Hash algo: sha1
Hash value: 60c14d260a80884c3acb5353804d7cb04703543e
Default Configuration: 'config@hk09'
Configuration 0 (config@hk09)
Description: OpenWrt arcadyan_aw1000
Kernel: kernel-1
FDT: fdt-1
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.104
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 13293044 Bytes = 12.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: d3522b67
Hash algo: sha1
Hash value: 026459c92f0fb956e513faff5119b8893388fb8a
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44cad81c
Data Size: 45589 Bytes = 44.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: a5a6c97f
Hash algo: sha1
Hash value: 60c14d260a80884c3acb5353804d7cb04703543e
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x44cad81c
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f1000, end 4a3ff214 ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.104 (builder@buildhost) (aarch64-openwrt-linux- musl-gcc (OpenWrt GCC 13.3.0 r28872-daca7c049b) 13.3.0, GNU ld (GNU Binutils) 2. 42) #0 SMP Fri Sep 19 21:19:38 2025
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 K iB) nomap non-reusable nss@40000000
[ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 Ki B) nomap non-reusable tzapp@4a400000
[ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 Ki B) nomap non-reusable bootloader@4a600000
[ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 Ki B) nomap non-reusable sbl@4aa00000
[ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 Ki B) nomap non-reusable smem@4ab00000
[ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 Ki B) nomap non-reusable memory@4ac00000
[ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 K iB) nomap non-reusable wcnss@4b000000
[ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 Ki B) nomap non-reusable q6_etr_dump@50f00000
[ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 Ki B) nomap non-reusable m3_dump@51000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 18 pages/cpu s36136 r8192 d29400 u73728
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.m td=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=m td:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs ro otfstype=squashfs rootwait root=/dev/ubiblock0_1
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be p assed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, li near)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec0000 0] (1MB)
[ 0.000000] Memory: 877964K/1048576K available (8640K kernel code, 922K rwdat a, 1660K rodata, 9536K init, 293K bss, 170612K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: 0xffffffc080010000
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt ).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 43980 46511078ns
[ 0.000125] Calibrating delay loop (skipped), value calculated using timer fr equency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000139] pid_max: default: 32768 minimum: 301
[ 0.005097] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, line ar)
[ 0.005112] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.009397] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adju st=1 rcu_task_cpu_ids=4.
[ 0.009624] rcu: Hierarchical SRCU implementation.
[ 0.009629] rcu: Max phase no-delay instances is 1000.
[ 0.010529] smp: Bringing up secondary CPUs ...
[ 0.011200] Detected VIPT I-cache on CPU1
[ 0.011306] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.011983] Detected VIPT I-cache on CPU2
[ 0.012054] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.012718] Detected VIPT I-cache on CPU3
[ 0.012784] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.012854] smp: Brought up 1 node, 4 CPUs
[ 0.012862] SMP: Total of 4 processors activated.
[ 0.012867] CPU features: detected: 32-bit EL0 Support
[ 0.012872] CPU features: detected: CRC32 instructions
[ 0.012930] CPU features: emulated: Privileged Access Never (PAN) using TTBR0 _EL1 switching
[ 0.012936] CPU: All CPU(s) started at EL1
[ 0.012939] alternatives: applying system-wide alternatives
[ 0.023849] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.023876] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.025603] pinctrl core: initialized pinctrl subsystem
[ 0.027664] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.028348] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.028387] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allo cations
[ 0.028422] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic al locations
[ 0.028841] thermal_sys: Registered thermal governor 'step_wise'
[ 0.028900] cpuidle: using governor menu
[ 0.029197] ASID allocator initialised with 65536 entries
[ 0.056081] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.058946] Modules: 27456 pages in range for non-PLT usage
[ 0.058954] Modules: 518976 pages in range for PLT usage
[ 0.062636] SCSI subsystem initialized
[ 0.062855] usbcore: registered new interface driver usbfs
[ 0.062899] usbcore: registered new interface driver hub
[ 0.062951] usbcore: registered new device driver usb
[ 0.063419] qcom_scm: convention: smc arm 64
[ 0.065228] clocksource: Switched to clocksource arch_sys_counter
[ 0.069165] NET: Registered PF_INET protocol family
[ 0.069314] IP idents hash table entries: 16384 (order: 5, 131072 bytes, line ar)
[ 0.072193] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.072218] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.072233] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.072319] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear )
[ 0.072594] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.073095] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, line ar)
[ 0.073267] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.073305] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.073640] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.073691] PCI: CLS 0 bytes, default 64
[ 0.087911] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.088650] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.088657] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.092588] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 48)
[ 0.096388] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dumm y regulator
[ 0.096592] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dumm y regulator
[ 0.097579] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dumm y regulator
[ 0.097722] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dumm y regulator
[ 0.098850] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regul ator
[ 0.098987] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.099071] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using d ummy regulator
[ 0.099253] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.099481] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regul ator
[ 0.099592] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.099634] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using d ummy regulator
[ 0.099821] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.102180] gpio-export gpio-export: 4 gpio(s) exported
[ 0.109300] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.113260] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.113304] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.113663] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.113698] msm_serial: console setup on port #0
[ 0.113741] printk: console [ttyMSM0] enabled
[ 0.967405] msm_serial: driver initialized
[ 0.976978] loop: module loaded
[ 0.978254] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 0.978938] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 0.985553] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB si ze: 256
[ 1.001848] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 1.113693] i2c_dev: i2c /dev entries driver
[ 1.120160] sdhci: Secure Digital Host Controller Interface driver
[ 1.120205] sdhci: Copyright(c) Pierre Ossman
[ 1.125301] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.131580] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 1.139116] NET: Registered PF_INET6 protocol family
[ 1.142408] Segment Routing with IPv6
[ 1.146341] In-situ OAM (IOAM) with IPv6
[ 1.149874] NET: Registered PF_PACKET protocol family
[ 1.153825] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.158953] 8021q: 802.1Q VLAN Support v1.8
[ 1.203443] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 1.203805] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.209623] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.216195] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.223830] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.231363] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.240497] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.247443] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 816000 uV
[ 1.257414] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 880000 uV
[ 1.267219] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 960000 uV
[ 1.277078] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 746, quot_offset[ 7]= 0
[ 1.286841] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 964, quot_offset[ 7]= 215
[ 1.297690] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1076, quot_offset[ 7]= 110
[ 1.308628] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1224, quot_offset[ 7]= 145
[ 1.319770] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.322234] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 1.337281] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 1.343678] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB si ze: 256
[ 1.358872] 26 qcomsmem partitions found on MTD device qcom_nand.0
[ 1.358923] Creating 26 MTD partitions on "qcom_nand.0":
[ 1.363961] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.370523] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.375298] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.380037] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.385407] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.391898] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.397152] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.401020] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.406203] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.411613] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.416638] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.421526] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.426331] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.431520] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.436212] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.441398] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.447095] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.452045] 0x000000f80000-0x000001000000 : "0:art"
[ 1.457372] 0x000001000000-0x000007400000 : "rootfs"
[ 1.503074] mtd: setting mtd18 (rootfs) as root device
[ 1.503601] mtdsplit: no squashfs found in "rootfs"
[ 1.507175] 0x000007400000-0x000008c80000 : "0:wififw"
[ 1.522419] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 1.564265] 0x00000f080000-0x000010900000 : "0:wififw_1"
[ 1.574968] 0x000010900000-0x000010b40000 : "0:ethphyfw"
[ 1.576451] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 1.580268] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 1.588502] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 1.897670] cpufreq: cpufreq_online: CPU0: Running at unlisted initial freque ncy: 800000 KHz, changing to: 1017600 KHz
[ 1.899570] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 1.907711] ubi0: attaching mtd18
[ 2.320238] ubi0: scanning is finished
[ 2.326674] ubi0: attached mtd18 (name "rootfs", size 100 MiB)
[ 2.326716] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 2.331408] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 2.338287] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 2.345123] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 2.351902] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 12 8
[ 2.358152] ubi0: max/mean erase counter: 72/45, WL threshold: 4096, image se quence number: 308896951
[ 2.365180] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
[ 2.374488] ubi0: background thread "ubi_bgt0d" started, PID 708
[ 2.375466] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.389764] ubi: mtd18 is already attached to ubi0
[ 2.395032] UBI error: cannot attach mtd18
[ 2.399814] ubi: mtd18 is already attached to ubi0
[ 2.403887] UBI error: cannot attach ▒[ 2.416302] Freeing unused kernel me mory: 9536K
[ 2.416476] Run /init as init process
[ 2.611397] init: Console is alive
[ 2.611520] init: - watchdog -
[ 2.619263] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.632280] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.644051] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist
[ 3.775303] regi_init[2525]:INFO:Initializing HPPE Done!!
[ 3.775447] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[ 3.781775] EDMA ver 1 hw init
[ 3.786008] EDMA HW Reset completed succesfully
[ 3.788661] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 3.793058] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 3.798697] dp1: ppe offload disabled: 0 for macid 1
[ 3.802433] dp1: Switch attached to macid 1 status: 0
[ 4.006044] Qualcomm QCA8075 90000.mdio-1:00: attached PHY driver (mii_bus:ph y_addr=90000.mdio-1:00, irq=POLL)
[ 4.006956] dp2: ppe offload disabled: 0 for macid 2
[ 4.014934] dp2: Switch attached to macid 2 status: 0
[ 4.095584] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:ph y_addr=90000.mdio-1:01, irq=POLL)
[ 4.096475] dp3: ppe offload disabled: 0 for macid 3
[ 4.104476] dp3: Switch attached to macid 3 status: 0
[ 4.185603] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:ph y_addr=90000.mdio-1:02, irq=POLL)
[ 4.186481] dp4: ppe offload disabled: 0 for macid 4
[ 4.194495] dp4: Switch attached to macid 4 status: 0
[ 4.275587] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:ph y_addr=90000.mdio-1:03, irq=POLL)
[ 4.276469] dp6-syn: ppe offload disabled: 0 for macid 6
[ 4.284480] dp6-syn: Switch attached to macid 6 status: 0
[ 4.387236] Qualcomm QCA8081 90000.mdio-1:1c: attached PHY driver (mii_bus:ph y_addr=90000.mdio-1:1c, irq=POLL)
[ 4.388112] **********************************************************
[ 4.396147] * NSS Data Plane driver
[ 4.402632] **********************************************************
[ 4.422250] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.422300] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus nu mber 1
[ 4.426802] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.434224] xhci-hcd xhci-hcd.1.auto: irq 41, io mem 0x08a00000
[ 4.443654] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.449470] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus nu mber 2
[ 4.455024] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.463001] hub 1-0:1.0: USB hub found
[ 4.469297] hub 1-0:1.0: 1 port detected
[ 4.473173] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM.
[ 4.477440] hub 2-0:1.0: USB hub found
[ 4.485068] hub 2-0:1.0: 1 port detected
[ 4.489040] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.492699] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus nu mber 3
[ 4.498201] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.505602] xhci-hcd xhci-hcd.2.auto: irq 42, io mem 0x08c00000
[ 4.514997] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.520825] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus nu mber 4
[ 4.526387] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 4.534363] hub 3-0:1.0: USB hub found
[ 4.540548] hub 3-0:1.0: 1 port detected
[ 4.544481] usb usb4: We don't know the algorithms for LPM for this host, dis abling LPM.
[ 4.548627] hub 4-0:1.0: USB hub found
[ 4.556431] hub 4-0:1.0: 1 port detected
[ 4.561170] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 4.567986] init: - preinit -
[ 5.205221] random: crng init done
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.585289] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 8.415396] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 9.383846] nss-dp 3a001000.dp1 lan1: PHY Link is down
[ 9.387442] procd: - early -
[ 9.387939] procd: - watchdog -
[ 9.915820] procd: - watchdog -
[ 9.916057] procd: - ubus -
[ 9.969947] procd: - init -
Please press Enter to activate this console.
[ 10.102537] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.183651] usbcore: registered new interface driver cdc_wdm
[ 10.184004] Loading modules backported from Linux version v6.12.44-0-g11a2452 8d080
[ 10.188409] Backport generated by backports.git v6.1.110-1-35-g410656ef
[ 10.199795] NET: Registered PF_QIPCRTR protocol family
[ 10.207384] usbcore: registered new interface driver usbserial_generic
[ 10.207517] usbserial: USB Serial support registered for generic
[ 10.247367] PPP generic driver version 2.4.2
[ 10.248065] NET: Registered PF_PPPOX protocol family
[ 10.251558] usbcore: registered new interface driver qmi_wwan
[ 10.268683] ath11k c000000.wifi: ipq8074 hw2.0
[ 10.268721] ath11k c000000.wifi: FW memory mode: 0
[ 10.273278] urngd: v1.0.2 started.
[ 10.423028] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 10.423134] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 10.774496] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 10.818456] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 10.825926] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 s oc_id 0xffffffff
[ 10.825961] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 202 4-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 10.855451] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 15.967390] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcs s
[ 15.967440] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 15.973702] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 16.323840] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 16.325601] usbcore: registered new interface driver option
[ 16.330344] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.335789] option 4-1:1.0: GSM modem (1-port) converter detected
[ 16.342684] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 16.349022] option 4-1:1.1: GSM modem (1-port) converter detected
[ 16.355830] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 16.361836] option 4-1:1.2: GSM modem (1-port) converter detected
[ 16.367705] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 16.368670] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 16.380339] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 s oc_id 0xffffffff
[ 16.380761] option 4-1:1.3: GSM modem (1-port) converter detected
[ 16.387472] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 202 4-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 16.396172] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB3
[ 16.416908] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.690411] ath11k c000000.wifi: htt event 48 not handled
[ 20.447258] br-lan: port 1(lan1) entered blocking state
[ 20.447300] br-lan: port 1(lan1) entered disabled state
[ 20.451342] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
[ 20.456812] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
[ 20.469881] br-lan: port 2(lan2) entered blocking state
[ 20.469924] br-lan: port 2(lan2) entered disabled state
[ 20.473967] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
[ 20.479431] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
[ 20.490161] br-lan: port 3(lan3) entered blocking state
[ 20.490941] br-lan: port 3(lan3) entered disabled state
[ 20.496139] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
[ 20.501468] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
[ 20.510825] br-lan: port 4(lan4) entered blocking state
[ 20.513075] br-lan: port 4(lan4) entered disabled state
[ 20.518291] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
[ 20.523593] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
[ 23.605725] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 23.605785] br-lan: port 1(lan1) entered blocking state
[ 23.610466] br-lan: port 1(lan1) entered forwarding state
[ 32.485270] l11: disabling
separate the USB before Sysupgrade and then……… Sysupgrade ...
here goes nothing
[ 1435.578792] usb 2-1: USB disconnect, device number 2
Watchdog handover: fd=3
- watchdog -
Watchdog did not previously reset the system
Thu Jan 1 00:24:05 UTC 1970 upgrade: Sending TERM to remaining processes ...
Thu Jan 1 00:24:05 UTC 1970 upgrade: Sending signal TERM to ntpd (3221)
Thu Jan 1 00:24:05 UTC 1970 upgrade: Sending signal TERM to ntpd (3265)
Thu Jan 1 00:24:09 UTC 1970 upgrade: Sending KILL to remaining processes ...
Thu Jan 1 00:24:09 UTC 1970 upgrade: Sending signal KILL to ntpd (3221)
Thu Jan 1 00:24:11 UTC 1970 upgrade: Sending signal KILL to ntpd (3265)
[ 1459.786156] stage2 (4017): drop_caches: 3
Thu Jan 1 00:24:19 UTC 1970 upgrade: Switching to ramdisk...
Thu Jan 1 00:24:20 UTC 1970 upgrade: Performing system upgrade...
verifying sysupgrade tar file integrity
[ 1461.325386] block ubiblock0_1: released
Volume ID 0, size 21 LEBs (5332992 bytes, 5.0 MiB), LEB size 253952 bytes (248.0
[ 1461.586472] block ubiblock0_1: created from ubi0:1(rootfs)
Volume ID 1, size 30 LEBs (7618560 bytes, 7.2 MiB), LEB size 253952 bytes (248.0
Set volume size to 67297280
Volume ID 2, size 265 LEBs (67297280 bytes, 64.1 MiB), LEB size 253952 bytes (24
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 1464.090636] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcs
[ 1464.585468] reboot: Restarting system
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 3448 - bootable_media_detect_success, Start
B - 3453 - elf_loader_entry, Start
B - 7632 - auth_hash_seg_entry, Start
B - 7877 - auth_hash_seg_exit, Start
B - 69791 - elf_segs_hash_verify_entry, Start
B - 132634 - PBL, End
B - 221887 - SBL1, Start
B - 301919 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 311893 - pm_device_init, Start
B - 496997 - PM_SET_VAL:Skip
D - 183122 - pm_device_init, Delta
B - 499407 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 505781 - clock_init, Start
D - 2135 - clock_init, Delta
B - 509716 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 530029 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 537410 - Boot Setting : 0x00000618
B - 541527 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 548329 - sbl1_ddr_set_params, Start
B - 552141 - CPR configuration: 0x30c
B - 555618 - cpr_init, Start
B - 558394 - Rail:0 Mode: 5 Voltage: 792000
B - 563609 - CL CPR settled at 744000mV
B - 566415 - Rail:1 Mode: 5 Voltage: 880000
B - 570624 - Rail:1 Mode: 7 Voltage: 896000
D - 16561 - cpr_init, Delta
B - 577487 - Pre_DDR_clock_init, Start
B - 581513 - Pre_DDR_clock_init, End
B - 584807 - DDR Type : PCDDR3
B - 590510 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 595360 - DDR: Start of HAL DDR Boot Training
B - 600026 - DDR: End of HAL DDR Boot Training
B - 605791 - DDR: Checksum to be stored on flash is 1789927307
B - 616100 - Image Load, Start
D - 216031 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 832223 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 839909 - Image Load, Start
D - 11986 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 851987 - Image Load, Start
D - 23027 - RPM Image Loaded, Delta - (86584 Bytes)
B - 875106 - Image Load, Start
D - 88724 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 963952 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 969747 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 976152 - SBL1, End
D - 756553 - SBL1, Delta
S - Flash Throughput, 6902 KB/s (2053791 Bytes, 297548 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
[do_boot_unsignedimg(887)] debug:0
setenv - set environment variables
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
IPQ807x#
reset
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 3446 - bootable_media_detect_success, Start
B - 3450 - elf_loader_entry, Start
B - 7619 - auth_hash_seg_entry, Start
B - 7864 - auth_hash_seg_exit, Start
B - 69628 - elf_segs_hash_verify_entry, Start
B - 132470 - PBL, End
B - 217617 - SBL1, Start
B - 296094 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 305884 - pm_device_init, Start
B - 487115 - PM_SET_VAL:Skip
D - 179309 - pm_device_init, Delta
B - 489525 - pm_driver_init, Start
D - 5337 - pm_driver_init, Delta
B - 495838 - clock_init, Start
D - 2135 - clock_init, Delta
B - 499864 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 520177 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 527558 - Boot Setting : 0x00000618
B - 531676 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 538477 - sbl1_ddr_set_params, Start
B - 542290 - CPR configuration: 0x30c
B - 545767 - cpr_init, Start
B - 548542 - Rail:0 Mode: 5 Voltage: 792000
B - 553758 - CL CPR settled at 744000mV
B - 556564 - Rail:1 Mode: 5 Voltage: 880000
B - 560773 - Rail:1 Mode: 7 Voltage: 896000
D - 16561 - cpr_init, Delta
B - 567635 - Pre_DDR_clock_init, Start
B - 571661 - Pre_DDR_clock_init, End
B - 574955 - DDR Type : PCDDR3
B - 580720 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 585478 - DDR: Start of HAL DDR Boot Training
B - 590205 - DDR: End of HAL DDR Boot Training
B - 595878 - DDR: Checksum to be stored on flash is 1789927307
B - 606309 - Image Load, Start
D - 215971 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 822371 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 830057 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 842166 - Image Load, Start
D - 23027 - RPM Image Loaded, Delta - (86584 Bytes)
B - 865285 - Image Load, Start
D - 88663 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 954070 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 959865 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 966270 - SBL1, End
D - 750941 - SBL1, Delta
S - Flash Throughput, 6900 KB/s (2053791 Bytes, 297642 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
IPQ807x# sb start
Unknown command 'sb' - try 'help'
IPQ807x# usbboot 0x44000000 0
** Bad device usb 0 **
IPQ807x# bootm 0x44000000
Wrong Image Format for bootm command
ERROR: can't get kernel image!
IPQ807x# usb start
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... cannot reset port 1!?
2 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
IPQ807x# usbboot 0x44000000 0
Loading from usb device 0, partition 0: Name: Whole Disk Type: U-Boot
Fit image detected...
WARN halted endpoint
WARN halted endpoint
WARN halted endpoint
** Read error on 0:0
IPQ807x# bootm 0x44000000
Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.104
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 16599229 Bytes = 15.8 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: c05b5cc9
Hash algo: sha1
Hash value: 7bd2857582d3aa5f359fe14463659486644a17f6
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt arcadyan_aw1000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44fd4ae8
Data Size: 45589 Bytes = 44.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: a5a6c97f
Hash algo: sha1
Hash value: 60c14d260a80884c3acb5353804d7cb04703543e
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x44fd4ae8
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f1000, end 4a3ff214 ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.104 (``buildbot@buildbot.infra.immortalwrt.org``) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r33451-5531f6bc76a3) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Sun Sep 21 14:45:27 2025
[ 0.000000] Machine model: Arcadyan AW1000
[ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000
[ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000
[ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000
[ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000
[ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000
[ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
[ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000
[ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 18 pages/cpu s36136 r8192 d29400 u73728
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[ 0.000000] Unknown kernel command line parameters "pcie_dev=RG50", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[ 0.000000] Memory: 874188K/1048576K available (8640K kernel code, 922K rwdata, 2580K rodata, 12416K init, 293K bss, 174388K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000124] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000138] pid_max: default: 32768 minimum: 301
[ 0.005187] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.005202] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.009518] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.009748] rcu: Hierarchical SRCU implementation.
[ 0.009753] rcu: Max phase no-delay instances is 1000.
[ 0.010663] smp: Bringing up secondary CPUs ...
[ 0.011328] Detected VIPT I-cache on CPU1
[ 0.011435] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.012107] Detected VIPT I-cache on CPU2
[ 0.012178] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.012837] Detected VIPT I-cache on CPU3
[ 0.012904] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.012975] smp: Brought up 1 node, 4 CPUs
[ 0.012983] SMP: Total of 4 processors activated.
[ 0.012988] CPU features: detected: 32-bit EL0 Support
[ 0.012993] CPU features: detected: CRC32 instructions
[ 0.013053] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.013059] CPU: All CPU(s) started at EL1
[ 0.013062] alternatives: applying system-wide alternatives
[ 0.024101] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.024128] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.025867] pinctrl core: initialized pinctrl subsystem
[ 0.027936] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.028616] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.028654] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.028692] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.029119] thermal_sys: Registered thermal governor 'step_wise'
[ 0.029179] cpuidle: using governor menu
[ 0.029476] ASID allocator initialised with 65536 entries
[ 0.085738] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.088586] Modules: 26512 pages in range for non-PLT usage
[ 0.088594] Modules: 518032 pages in range for PLT usage
[ 0.092270] SCSI subsystem initialized
[ 0.092503] usbcore: registered new interface driver usbfs
[ 0.092546] usbcore: registered new interface driver hub
[ 0.092596] usbcore: registered new device driver usb
[ 0.093049] qcom_scm: convention: smc arm 64
[ 0.094894] clocksource: Switched to clocksource arch_sys_counter
[ 0.098845] NET: Registered PF_INET protocol family
[ 0.099011] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.101906] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.101930] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.101946] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.102031] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.102303] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.102815] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[ 0.103003] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.103041] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.103356] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.103394] PCI: CLS 0 bytes, default 64
[ 0.105533] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.106291] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.106298] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.110182] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.113992] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.114214] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.115867] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.116034] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.117902] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator
[ 0.118049] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.118123] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.118337] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.118555] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.118681] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.118723] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.118901] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.121322] gpio-export gpio-export: 4 gpio(s) exported
[ 0.129769] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.133436] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.133482] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.133838] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.133870] msm_serial: console setup on port #0
[ 0.133911] printk: console [ttyMSM0] enabled
[ 0.989420] msm_serial: driver initialized
[ 0.998681] loop: module loaded
[ 0.999879] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 1.000642] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 1.007259] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.028685] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 1.166468] i2c_dev: i2c /dev entries driver
[ 1.172933] sdhci: Secure Digital Host Controller Interface driver
[ 1.172977] sdhci: Copyright(c) Pierre Ossman
[ 1.178052] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.184337] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 1.192213] NET: Registered PF_INET6 protocol family
[ 1.195143] Segment Routing with IPv6
[ 1.199060] In-situ OAM (IOAM) with IPv6
[ 1.202645] NET: Registered PF_PACKET protocol family
[ 1.206614] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.211731] 8021q: 802.1Q VLAN Support v1.8
[ 1.255822] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 1.256167] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.261947] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.268598] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.276242] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.283720] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.292887] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 1.299824] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 816000 uV
[ 1.309813] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 880000 uV
[ 1.319615] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 960000 uV
[ 1.329478] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 746, quot_offset[ 7]= 0
[ 1.339235] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 964, quot_offset[ 7]= 215
[ 1.350087] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1076, quot_offset[ 7]= 110
[ 1.361023] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1224, quot_offset[ 7]= 145
[ 1.372193] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.374660] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 1.389678] nand: Toshiba TH58NYG3S0HBAI4 8G 1.8V 8-bit
[ 1.396066] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 1.416452] 26 qcomsmem partitions found on MTD device qcom_nand.0
[ 1.416500] Creating 26 MTD partitions on "qcom_nand.0":
[ 1.421538] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.428121] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.432912] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.437609] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.442977] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.449682] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.454711] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.458667] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.463713] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.469209] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.474159] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.479109] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.483862] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.489192] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.493776] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.499038] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.504575] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.509718] 0x000000f80000-0x000001000000 : "0:art"
[ 1.514947] 0x000001000000-0x000007400000 : "rootfs"
[ 1.560895] mtd: setting mtd18 (rootfs) as root device
[ 1.561433] mtdsplit: no squashfs found in "rootfs"
[ 1.564987] 0x000007400000-0x000008c80000 : "0:wififw"
[ 1.580423] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 1.622538] 0x00000f080000-0x000010900000 : "0:wififw_1"
[ 1.633291] 0x000010900000-0x000010b40000 : "0:ethphyfw"
[ 1.634808] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 1.638620] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 1.646820] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 1.959625] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 1.961662] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 1.969867] ubi0: attaching mtd18
[ 2.384126] ubi0: scanning is finished
[ 2.390596] ubi0: attached mtd18 (name "rootfs", size 100 MiB)
[ 2.390636] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 2.395345] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 2.402186] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 2.409052] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 2.415820] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.422066] ubi0: max/mean erase counter: 72/46, WL threshold: 4096, image sequence number: 308896951
[ 2.429107] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
[ 2.438402] ubi0: background thread "ubi_bgt0d" started, PID 711
[ 2.448185] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.453681] ubi: mtd18 is already attached to ubi0
[ 2.458968] UBI error: cannot attach mtd18
[ 2.463831] ubi: mtd18 is already attached to ubi0
[ 2.467823] UBI error: cannot attach mtd[ 2.481542] Freeing unused kernel memory: 12416K
[ 2.481876] Run /init as init process
[ 2.739242] init: Console is alive
[ 2.739354] init: - watchdog -
[ 2.747948] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.766441] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.780691] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist
[ 3.904983] regi_init[2525]:INFO:Initializing HPPE Done!!
[ 3.905120] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[ 3.911588] EDMA ver 1 hw init
[ 3.915696] EDMA HW Reset completed succesfully
[ 3.918341] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 3.922736] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 3.928383] dp1: ppe offload disabled: 0 for macid 1
[ 3.932112] dp1: Switch attached to macid 1 status: 0
[ 4.135682] Qualcomm QCA8075 90000.mdio-1:00: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:00, irq=POLL)
[ 4.136844] dp2: ppe offload disabled: 0 for macid 2
[ 4.144575] dp2: Switch attached to macid 2 status: 0
[ 4.235255] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL)
[ 4.236138] dp3: ppe offload disabled: 0 for macid 3
[ 4.244150] dp3: Switch attached to macid 3 status: 0
[ 4.325242] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL)
[ 4.326142] dp4: ppe offload disabled: 0 for macid 4
[ 4.334150] dp4: Switch attached to macid 4 status: 0
[ 4.415258] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[ 4.416126] dp6-syn: ppe offload disabled: 0 for macid 6
[ 4.424151] dp6-syn: Switch attached to macid 6 status: 0
[ 4.526872] Qualcomm QCA8081 90000.mdio-1:1c: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:1c, irq=POLL)
[ 4.527734] **********************************************************
[ 4.535792] * NSS Data Plane driver
[ 4.542271] **********************************************************
[ 4.563166] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.563217] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 4.567714] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.575156] xhci-hcd xhci-hcd.1.auto: irq 41, io mem 0x08a00000
[ 4.584586] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.590397] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 4.595946] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.603870] hub 1-0:1.0: USB hub found
[ 4.610255] hub 1-0:1.0: 1 port detected
[ 4.614097] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.618369] hub 2-0:1.0: USB hub found
[ 4.626006] hub 2-0:1.0: 1 port detected
[ 4.629881] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.633624] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[ 4.639080] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[ 4.646519] xhci-hcd xhci-hcd.2.auto: irq 42, io mem 0x08c00000
[ 4.655931] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.661737] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[ 4.667307] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 4.675184] hub 3-0:1.0: USB hub found
[ 4.681464] hub 3-0:1.0: 1 port detected
[ 4.685462] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.689537] hub 4-0:1.0: USB hub found
[ 4.697365] hub 4-0:1.0: 1 port detected
[ 4.703288] usbcore: registered new interface driver usb-storage
[ 4.705892] usbcore: registered new interface driver uas
[ 4.711169] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.718795] init: - preinit -
[ 5.414887] random: crng init done
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.734958] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 5.766341] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 5.766651] scsi host0: usb-storage 2-1:1.0
[ 6.805465] scsi 0:0:0:0: Direct-Access UFD 3.0 Silicon-Power32G 1.00 PQ: 0 ANSI: 6
[ 6.806916] sd 0:0:0:0: [sda] 60620800 512-byte logical blocks: (31.0 GB/28.9 GiB)
[ 6.812765] sd 0:0:0:0: [sda] Write Protect is off
[ 6.820189] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[ 6.827065] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 8.645096] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 9.619882] nss-dp 3a001000.dp1 lan1: PHY Link is down
[ 9.624220] procd: - early -
[ 9.624328] procd: - watchdog -
[ 9.753840] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 9.861370] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 9.968358] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.075851] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.152335] procd: - watchdog -
[ 10.152569] procd: - ubus -
[ 10.177362] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.287397] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.305835] procd: - init -
Please press Enter to activate this console.
[ 10.392480] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.448389] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.498258] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.538934] NET: Registered PF_ALG protocol family
[ 10.548054] ntfs3: Enabled Linux POSIX ACLs support
[ 10.550985] usbcore: registered new interface driver cdc_wdm
[ 10.552191] Loading modules backported from Linux version v6.12.44-0-g11a24528d080
[ 10.557662] Backport generated by backports.git v6.1.110-1-35-g410656ef
[ 10.571047] NET: Registered PF_QIPCRTR protocol family
[ 10.576181] usbcore: registered new interface driver ums-alauda
[ 10.577637] usbcore: registered new interface driver ums-cypress
[ 10.583310] usbcore: registered new interface driver ums-datafab
[ 10.589682] usbcore: registered new interface driver ums-freecom
[ 10.595512] usbcore: registered new interface driver ums-isd200
[ 10.601527] usbcore: registered new interface driver ums-jumpshot
[ 10.607378] usbcore: registered new interface driver ums-karma
[ 10.613447] usbcore: registered new interface driver ums-sddr09
[ 10.619247] usbcore: registered new interface driver ums-sddr55
[ 10.621356] urngd: v1.0.2 started.
[ 10.630414] usbcore: registered new interface driver ums-usbat
[ 10.636260] usbcore: registered new interface driver usbserial_generic
[ 10.639506] usbserial: USB Serial support registered for generic
[ 10.698460] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 10.702215] PPP generic driver version 2.4.2
[ 10.707263] PPP MPPE Compression module registered
[ 10.711588] NET: Registered PF_PPPOX protocol family
[ 10.716582] usbcore: registered new interface driver qmi_wwan
[ 10.730870] ath11k c000000.wifi: ipq8074 hw2.0
[ 10.730909] ath11k c000000.wifi: FW memory mode: 0
[ 10.822516] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 11.055076] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 13.937732] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 13.937840] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 14.290338] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 14.334335] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 14.341770] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 soc_id 0xffffffff
[ 14.341807] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 19.498845] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss
[ 19.498889] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 19.505031] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 19.855000] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 19.857214] usbcore: registered new interface driver option
[ 19.861511] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.866951] option 4-1:1.0: GSM modem (1-port) converter detected
[ 19.873851] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 19.880193] option 4-1:1.1: GSM modem (1-port) converter detected
[ 19.887015] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 19.892999] option 4-1:1.2: GSM modem (1-port) converter detected
[ 19.898801] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 19.899835] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 19.911453] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0x270 soc_id 0xffffffff
[ 19.911917] option 4-1:1.3: GSM modem (1-port) converter detected
[ 19.918644] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 19.927324] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB3
[ 19.948436] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 20.221667] ath11k c000000.wifi: htt event 48 not handled
[ 21.960645] mtdblock_open: 26 callbacks suppressed
[ 21.960658] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
[ 22.079023] /dev/ubiblock0_1: Can't open blockdev
[ 24.664263] br-lan: port 1(lan1) entered blocking state
[ 24.664306] br-lan: port 1(lan1) entered disabled state
[ 24.668437] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
[ 24.673755] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
[ 24.686094] br-lan: port 2(lan2) entered blocking state
[ 24.686139] br-lan: port 2(lan2) entered disabled state
[ 24.690474] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
[ 24.695980] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
[ 24.705243] br-lan: port 3(lan3) entered blocking state
[ 24.707457] br-lan: port 3(lan3) entered disabled state
[ 24.712614] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
[ 24.718071] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
[ 24.727660] br-lan: port 4(lan4) entered blocking state
[ 24.729594] br-lan: port 4(lan4) entered disabled state
[ 24.734744] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
[ 24.740212] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
[ 26.251479] br-lan: port 5(phy0-ap0) entered blocking state
[ 26.251524] br-lan: port 5(phy0-ap0) entered disabled state
[ 26.255947] ath11k c000000.wifi phy0-ap0: entered allmulticast mode
[ 26.261643] ath11k c000000.wifi phy0-ap0: entered promiscuous mode
[ 26.337187] br-lan: port 6(phy1-ap0) entered blocking state
[ 26.337232] br-lan: port 6(phy1-ap0) entered disabled state
[ 26.341620] ath11k c000000.wifi phy1-ap0: entered allmulticast mode
[ 26.347321] ath11k c000000.wifi phy1-ap0: entered promiscuous mode
[ 26.353453] br-lan: port 6(phy1-ap0) entered blocking state
[ 26.359641] br-lan: port 6(phy1-ap0) entered forwarding state
[ 26.730876] br-lan: port 5(phy0-ap0) entered blocking state
[ 26.730928] br-lan: port 5(phy0-ap0) entered forwarding state
[ 27.765055] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[ 27.765117] br-lan: port 1(lan1) entered blocking state
[ 27.769801] br-lan: port 1(lan1) entered forwarding state
[ 32.484938] l11: disabling
[ 259.587520] ath11k c000000.wifi phy1-ap0: left allmulticast mode
[ 259.587576] ath11k c000000.wifi phy1-ap0: left promiscuous mode
[ 259.592696] br-lan: port 6(phy1-ap0) entered disabled state
[ 534.583214] ath11k c000000.wifi phy0-ap0: left allmulticast mode
[ 534.583275] ath11k c000000.wifi phy0-ap0: left promiscuous mode
[ 534.588411] br-lan: port 5(phy0-ap0) entered disabled state
Watchdog handover: fd=3
watchdog -
Watchdog did not previously reset the system
Thu Jan 1 08:08:54 CST 1970 upgrade: Sending TERM to remaining processes ...
Thu Jan 1 08:08:54 CST 1970 upgrade: Sending signal TERM to hostapd (3197)
Thu Jan 1 08:08:54 CST 1970 upgrade: Sending signal TERM to hostapd (3252)
[ 537.583681] usb 2-1: USB disconnect, device number 2
Thu Jan 1 08:08:58 CST 1970 upgrade: Sending KILL to remaining processes ...
[ 545.005821] stage2 (7162): drop_caches: 3
Thu Jan 1 08:09:05 CST 1970 upgrade: Switching to ramdisk...
Thu Jan 1 00:09:06 UTC 1970 upgrade: Performing system upgrade...
verifying sysupgrade tar file integrity
[ 546.985062] block ubiblock0_1: released
Volume ID 0, size 21 LEBs (5332992 bytes, 5.0 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "kernel", alignment 1
[ 547.289535] block ubiblock0_1: created from ubi0:1(rootfs)
Volume ID 1, size 113 LEBs (28696576 bytes, 27.3 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 46219264
Volume ID 2, size 182 LEBs (46219264 bytes, 44.0 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 553.181517] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss
[ 553.695155] reboot: Restarting system
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 3446 - bootable_media_detect_success, Start
B - 3450 - elf_loader_entry, Start
B - 7619 - auth_hash_seg_entry, Start
B - 7864 - auth_hash_seg_exit, Start
B - 69630 - elf_segs_hash_verify_entry, Start
B - 132472 - PBL, End
B - 222924 - SBL1, Start
B - 303261 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 313235 - pm_device_init, Start
B - 496204 - PM_SET_VAL:Skip
D - 180926 - pm_device_init, Delta
B - 498614 - pm_driver_init, Start
D - 5337 - pm_driver_init, Delta
B - 504927 - clock_init, Start
D - 2135 - clock_init, Delta
B - 508953 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 529266 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 536647 - Boot Setting : 0x00000618
B - 540765 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 547566 - sbl1_ddr_set_params, Start
B - 551379 - CPR configuration: 0x30c
B - 554856 - cpr_init, Start
B - 557631 - Rail:0 Mode: 5 Voltage: 792000
B - 562847 - CL CPR settled at 744000mV
B - 565653 - Rail:1 Mode: 5 Voltage: 880000
B - 569862 - Rail:1 Mode: 7 Voltage: 896000
D - 16531 - cpr_init, Delta
B - 576724 - Pre_DDR_clock_init, Start
B - 580750 - Pre_DDR_clock_init, End
B - 584044 - DDR Type : PCDDR3
B - 589809 - do ddr sanity test, Start
D - 1037 - do ddr sanity test, Delta
B - 594567 - DDR: Start of HAL DDR Boot Training
B - 599294 - DDR: End of HAL DDR Boot Training
B - 604967 - DDR: Checksum to be stored on flash is 1789927307
B - 615398 - Image Load, Start
D - 216032 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 831521 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 839207 - Image Load, Start
D - 11987 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 851285 - Image Load, Start
D - 23058 - RPM Image Loaded, Delta - (86584 Bytes)
B - 874404 - Image Load, Start
D - 88725 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 963251 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 969046 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 975451 - SBL1, End
D - 754845 - SBL1, Delta
S - Flash Throughput, 6899 KB/s (2053791 Bytes, 297671 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
[do_boot_unsignedimg(887)] debug:0
setenv - set environment variables
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
IPQ807x#
after restart (without usb) no changes will remain ...I used these resources for Sysupgrade ...
etc.
So, if you removed the USB, the router will not boot, right?
Can you show the output of
printenv
And boot your router from the USB, then connect to it using SSH and run this command,show the output.
cat /proc/mtd
Yap….
The output of
printenv
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2736 - bootable_media_detect_entry, Start
B - 3447 - bootable_media_detect_success, Start
B - 3452 - elf_loader_entry, Start
B - 7624 - auth_hash_seg_entry, Start
B - 7869 - auth_hash_seg_exit, Start
B - 69682 - elf_segs_hash_verify_entry, Start
B - 132524 - PBL, End
B - 144722 - SBL1, Start
B - 196999 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 203526 - pm_device_init, Start
B - 325862 - PM_SET_VAL:Skip
D - 121878 - pm_device_init, Delta
B - 328271 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 334646 - clock_init, Start
D - 2104 - clock_init, Delta
B - 338641 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 358863 - boot_config_data_table_init, Start
D - 4026 - boot_config_data_table_init, Delta - (575 Bytes)
B - 366244 - Boot Setting : 0x00000618
B - 370361 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 377163 - sbl1_ddr_set_params, Start
B - 380975 - CPR configuration: 0x30c
B - 384452 - cpr_init, Start
B - 387228 - Rail:0 Mode: 5 Voltage: 792000
B - 392443 - CL CPR settled at 744000mV
B - 395249 - Rail:1 Mode: 5 Voltage: 880000
B - 399428 - Rail:1 Mode: 7 Voltage: 896000
D - 16531 - cpr_init, Delta
B - 406321 - Pre_DDR_clock_init, Start
B - 410347 - Pre_DDR_clock_init, End
B - 413641 - DDR Type : PCDDR3
B - 419405 - do ddr sanity test, Start
D - 1037 - do ddr sanity test, Delta
B - 424163 - DDR: Start of HAL DDR Boot Training
B - 428891 - DDR: End of HAL DDR Boot Training
B - 434564 - DDR: Checksum to be stored on flash is 1789927307
B - 444995 - Image Load, Start
D - 215909 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 660996 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 668682 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 680790 - Image Load, Start
D - 23028 - RPM Image Loaded, Delta - (86584 Bytes)
B - 703909 - Image Load, Start
D - 88694 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 792725 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 798520 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 804925 - SBL1, End
D - 662491 - SBL1, Delta
S - Flash Throughput, 6903 KB/s (2053791 Bytes, 297519 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
[do_boot_unsignedimg(887)] debug:0
setenv - set environment variables
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Net: MAC0 addr:ec:6c:9a:b7:f4:68
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
IPQ807x# printenv
baudrate=115200
bootargs=console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait
bootcmd=run bootusb; bootipq
bootcount=0
bootdelay=2
bootusb=usb start && usbboot 0x44000000 0 && bootm 0x44000000
eth1addr=ec:6c:9a:b7:f4:68
eth2addr=ec:6c:9a:b7:f4:68
eth3addr=ec:6c:9a:b7:f4:68
eth4addr=ec:6c:9a:b7:f4:68
eth5addr=ec:6c:9a:b7:f4:68
ethact=eth0
ethaddr=ec:6c:9a:b7:f4:68
fdt_high=0x4A400000
fdtcontroladdr=4a9727a0
flash_type=2
fsbootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
ipaddr=192.168.1.254
machid=8010008
mtddevname=fs
mtddevnum=0
mtdids=nand0=nand0
mtdparts=mtdparts=nand0:0x6400000@0x1000000(fs),
netmask=255.255.255.0
partition=nand0,0
serverip=192.168.1.2
soc_version_major=2
soc_version_minor=0
stderr=serial@78B3000
stdin=serial@78B3000
stdout=serial@78B3000
Environment size: 1026/262140 bytes
IPQ807x#
cat /proc/mtd output :
BusyBox v1.36.1 (2025-09-21 14:45:27 UTC) built-in shell (ash)
.___ __ .__
| | _____ _____ ____________/ |______ | |
| |/ \ / \ / _ \_ __ \ __\__ \ | |
| | Y Y \ Y Y ( <_> ) | \/| | / __ \| |__
|___|__|_| /__|_| /\____/|__| |__| (____ /____/
\/ \/ BE FREE AND UNAFRAID \/
-----------------------------------------------------
ImmortalWrt 24.10.3, r33451-5531f6bc76a3
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@ImmortalWrt:~# ^C
root@ImmortalWrt:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00040000 "0:sbl1"
mtd1: 00100000 00040000 "0:mibib"
mtd2: 00080000 00040000 "0:bootconfig"
mtd3: 00080000 00040000 "0:bootconfig1"
mtd4: 00300000 00040000 "0:qsee"
mtd5: 00300000 00040000 "0:qsee_1"
mtd6: 00080000 00040000 "0:devcfg"
mtd7: 00080000 00040000 "0:devcfg_1"
mtd8: 00080000 00040000 "0:apdp"
mtd9: 00080000 00040000 "0:apdp_1"
mtd10: 00080000 00040000 "0:rpm"
mtd11: 00080000 00040000 "0:rpm_1"
mtd12: 00080000 00040000 "0:cdt"
mtd13: 00080000 00040000 "0:cdt_1"
mtd14: 00080000 00040000 "0:appsblenv"
mtd15: 00100000 00040000 "0:appsbl"
mtd16: 00100000 00040000 "0:appsbl_1"
mtd17: 00080000 00040000 "0:art"
mtd18: 06400000 00040000 "rootfs"
mtd19: 01880000 00040000 "0:wififw"
mtd20: 06400000 00040000 "rootfs_1"
mtd21: 01880000 00040000 "0:wififw_1"
mtd22: 00240000 00040000 "0:ethphyfw"
mtd23: 00100000 00040000 "0:board_data"
mtd24: 00800000 00040000 "0:arc_datadump"
mtd25: 2cbc0000 00040000 "0:arc_data"
Did you get something from this outputs?
Unfortunately, no. I suggest flashing the factory image one more time.