My version 1.1 BPiM2U won't boot. It hangs just after 33 seconds:
The end is the same for all releases to 22.03rc6.
openwrt-22.03.0-rc6-sunxi-cortexa7-sinovoip_bananapi-m2-ultra-ext4-sdcard.img.gz
U-Boot SPL 2020.04-OpenWrt-r19590-042d558536 (Jul 31 2022 - 15:12:47 +0000)
DRAM: 2048 MiB
Trying to boot from MMC1
U-Boot 2020.04-OpenWrt-r19590-042d558536 (Jul 31 2022 - 15:12:47 +0000) Allwinner Technology
CPU: Allwinner R40 (SUN8I 1701)
Model: Banana Pi BPI-M2-Ultra
I2C: ready
DRAM: 2 GiB
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial@1c28000
Out: serial@1c28000
Err: serial@1c28000
Net: phy interface7
eth0: ethernet@1c50000
starting USB...
Bus usb@1c19000: failed to get usb phy
Port not available.
Bus usb@1c19400: failed to get usb phy
Port not available.
Bus usb@1c1c000: failed to get usb phy
Port not available.
Bus usb@1c1c400: failed to get usb phy
Port not available.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
377 bytes read in 2 ms (183.6 KiB/s)
## Executing script at 43100000
3355024 bytes read in 156 ms (20.5 MiB/s)
22353 bytes read in 4 ms (5.3 MiB/s)
## Booting kernel from Legacy Image at 42000000 ...
Image Name: ARM OpenWrt Linux-5.10.134
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3354960 Bytes = 3.2 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Loading Kernel Image
Using Device Tree in place at 43000000, end 43008750
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.134 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r19590-042d558536) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sun Jul 31 15:12:47 2022
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Banana Pi BPI-M2-Ultra
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff]
[ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] percpu: Embedded 15 pages/cpu s30732 r8192 d22516 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2064180K/2097152K available (7549K kernel code, 838K rwdata, 1224K rodata, 2048K init, 257K bss, 32972K reserved, 0K cma-reserved, 1310708K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000019] Switching to timer-based delay loop, resolution 41ns
[ 0.000201] Console: colour dummy device 80x30
[ 0.000260] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000279] pid_max: default: 32768 minimum: 301
[ 0.000422] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000439] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.001314] CPU: Testing write buffer coherency: ok
[ 0.001686] /cpus/cpu@0 missing clock-frequency property
[ 0.001709] /cpus/cpu@1 missing clock-frequency property
[ 0.001726] /cpus/cpu@2 missing clock-frequency property
[ 0.001744] /cpus/cpu@3 missing clock-frequency property
[ 0.001756] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002443] Setting up static identity map for 0x40200000 - 0x40200060
[ 0.002576] rcu: Hierarchical SRCU implementation.
[ 0.002765] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.003167] smp: Bringing up secondary CPUs ...
[ 0.013931] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.024819] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.035635] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.035722] smp: Brought up 1 node, 4 CPUs
[ 0.035748] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.035755] CPU: All CPU(s) started in HYP mode.
[ 0.035761] CPU: Virtualization extensions available.
[ 0.041443] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.041693] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.041717] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.041978] pinctrl core: initialized pinctrl subsystem
[ 0.043581] NET: Registered protocol family 16
[ 0.044159] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.045525] thermal_sys: Registered thermal governor 'step_wise'
[ 0.045957] No ATAGs?
[ 0.078790] SCSI subsystem initialized
[ 0.079422] usbcore: registered new interface driver usbfs
[ 0.079503] usbcore: registered new interface driver hub
[ 0.079574] usbcore: registered new device driver usb
[ 0.079909] pps_core: LinuxPPS API ver. 1 registered
[ 0.079925] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.079953] PTP clock support registered
[ 0.080296] Advanced Linux Sound Architecture Driver Initialized.
[ 0.081657] clocksource: Switched to clocksource arch_sys_counter
[ 0.087612] NET: Registered protocol family 2
[ 0.087903] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.089159] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.089213] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.089288] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.089405] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.089532] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.089604] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.089884] NET: Registered protocol family 1
[ 0.091985] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 0.096113] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.096228] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.097232] bounce: pool size: 64 pages
[ 0.097308] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.098682] sun4i-usb-phy 1c13400.phy: failed to get clock usb0_phy
[ 0.100757] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pi not found, using dummy regulator
[ 0.115805] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.124196] loop: module loaded
[ 0.124507] Loading iSCSI transport class v2.0-870.
[ 0.129046] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.129084] ehci-platform: EHCI generic platform driver
[ 0.129657] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.129730] ohci-platform: OHCI generic platform driver
[ 0.130264] usbcore: registered new interface driver usb-storage
[ 0.130827] mousedev: PS/2 mouse device common for all mice
[ 0.132440] sun6i-rtc 1c20400.rtc: registered as rtc0
[ 0.132503] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01T00:00:05 UTC (5)
[ 0.132517] sun6i-rtc 1c20400.rtc: RTC enabled
[ 0.132733] i2c /dev entries driver
[ 0.134942] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 0.137843] NET: Registered protocol family 10
[ 0.138873] Segment Routing with IPv6
[ 0.138955] NET: Registered protocol family 17
[ 0.139013] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.139158] can: controller area network core
[ 0.139222] NET: Registered protocol family 29
[ 0.139232] 8021q: 802.1Q VLAN Support v1.8
[ 0.139350] Registering SWP/SWPB emulation handler
[ 0.152146] sun4i-usb-phy 1c13400.phy: Couldn't get regulator usb1_vbus... Deferring probe
[ 0.154028] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pi not found, using dummy regulator
[ 0.155661] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.157768] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator
[ 0.158215] printk: console [ttyS0] disabled
[ 0.178422] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 45, base_baud = 1500000) is a U6_16550A
[ 0.911327] printk: console [ttyS0] enabled
[ 0.916378] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator
[ 0.923192] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 198
[ 0.929802] sun4i-pinctrl 1c20800.pinctrl: pin-198 (1c28c00.serial) status -517
[ 0.937113] sun4i-pinctrl 1c20800.pinctrl: could not request pin 198 (PG6) from group PG6 on device 1c20800.pinctrl
[ 0.947636] dw-apb-uart 1c28c00.serial: Error applying setting, reverse things back
[ 0.955722] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator
[ 0.962519] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0
[ 0.968955] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -517
[ 0.976269] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl
[ 0.986607] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse things back
[ 0.997614] axp20x-i2c 0-0034: AXP20x variant AXP221 found
[ 1.010457] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp221-pek/input/input0
[ 1.029023] vcc-3v3: supplied by regulator-dummy
[ 1.034817] vdd-cpu: supplied by regulator-dummy
[ 1.040113] vdd-sys: supplied by regulator-dummy
[ 1.045579] dcdc4: supplied by regulator-dummy
[ 1.050547] vcc-dram: supplied by regulator-dummy
[ 1.055503] vcc-gmac-phy: failed to get the current voltage: -EPROBE_DEFER
[ 1.062406] vcc-gmac-phy: supplied by vcc-3v3
[ 1.067529] dc5ldo: supplied by vcc-dram
[ 1.072145] aldo1: supplied by regulator-dummy
[ 1.077236] vcc-pa: supplied by regulator-dummy
[ 1.082312] avcc: supplied by regulator-dummy
[ 1.087889] eldo1: supplied by regulator-dummy
[ 1.093067] eldo2: supplied by regulator-dummy
[ 1.098176] vdd1v2-sata: supplied by regulator-dummy
[ 1.103653] vcc-wifi-io: Bringing 700000uV into 1800000-1800000uV
[ 1.110631] vcc-wifi-io: supplied by regulator-dummy
[ 1.116147] vcc-wifi: Bringing 700000uV into 3300000-3300000uV
[ 1.122321] vcc-wifi: supplied by regulator-dummy
[ 1.127987] vcc-wifi-2: Bringing 700000uV into 3300000-3300000uV
[ 1.134345] vcc-wifi-2: supplied by regulator-dummy
[ 1.140382] vdd2v5-sata: supplied by regulator-dummy
[ 1.145477] rtc_ldo: supplied by regulator-dummy
[ 1.150905] ldo_io0: supplied by regulator-dummy
[ 1.156197] ldo_io1: supplied by regulator-dummy
[ 1.161355] axp20x-i2c 0-0034: AXP20X driver loaded
[ 1.169253] sun4i-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dummy regulator
[ 1.170468] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq
[ 1.177580] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 1.200055] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 46, base_baud = 1500000) is a U6_16550A
[ 1.201703] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, uses new timings mode
[ 1.210135] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found
[ 1.221679] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.221887] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.224267] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found
[ 1.248475] dwmac-sun8i 1c50000.ethernet: PTP uses main clock
[ 1.254263] dwmac-sun8i 1c50000.ethernet: Current syscon value is not the default 6 (expect 0)
[ 1.263288] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supported
[ 1.270511] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supported
[ 1.277752] dwmac-sun8i 1c50000.ethernet: COE Type 2
[ 1.281492] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.282717] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported
[ 1.282723] dwmac-sun8i 1c50000.ethernet: Normal descriptors
[ 1.282727] dwmac-sun8i 1c50000.ethernet: Chain mode enabled
[ 1.309427] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.317905] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.328861] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.332587] ehci-platform 1c19000.usb: EHCI Host Controller
[ 1.339962] ehci-platform 1c19000.usb: new USB bus registered, assigned bus number 1
[ 1.340963] mmc1: queuing unknown CIS tuple 0x81 (9 bytes)
[ 1.347731] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.347876] ehci-platform 1c19000.usb: irq 37, io mem 0x01c19000
[ 1.353275] mmc0: Problem switching card into high-speed mode!
[ 1.373302] mmc0: new SDHC card at address 0001
[ 1.378801] mmcblk0: mmc0:0001 ASTC 14.9 GiB
[ 1.381768] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00
[ 1.382121] mmc2: new DDR MMC card at address 0001
[ 1.383031] mmcblk2: mmc2:0001 8GTF4R 7.28 GiB
[ 1.383515] mmcblk2boot0: mmc2:0001 8GTF4R partition 1 4.00 MiB
[ 1.389506] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.389839] mmcblk0: p1 p2
[ 1.394699] mmcblk2boot1: mmc2:0001 8GTF4R partition 2 4.00 MiB
[ 1.398648] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.405354] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.412849] usb usb1: Product: EHCI Host Controller
[ 1.412855] usb usb1: Manufacturer: Linux 5.10.134 ehci_hcd
[ 1.412869] usb usb1: SerialNumber: 1c19000.usb
[ 1.450463] hub 1-0:1.0: USB hub found
[ 1.454284] hub 1-0:1.0: 1 port detected
[ 1.459267] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 1.464883] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[ 1.472813] ehci-platform 1c1c000.usb: irq 39, io mem 0x01c1c000
[ 1.501648] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 1.507928] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.516204] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.523433] usb usb2: Product: EHCI Host Controller
[ 1.528306] usb usb2: Manufacturer: Linux 5.10.134 ehci_hcd
[ 1.533879] usb usb2: SerialNumber: 1c1c000.usb
[ 1.538852] hub 2-0:1.0: USB hub found
[ 1.542669] hub 2-0:1.0: 1 port detected
[ 1.547734] ohci-platform 1c19400.usb: Generic Platform OHCI controller
[ 1.554398] ohci-platform 1c19400.usb: new USB bus registered, assigned bus number 3
[ 1.562289] ohci-platform 1c19400.usb: irq 38, io mem 0x01c19400
[ 1.635831] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 1.644108] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.651323] usb usb3: Product: Generic Platform OHCI controller
[ 1.657243] usb usb3: Manufacturer: Linux 5.10.134 ohci_hcd
[ 1.662815] usb usb3: SerialNumber: 1c19400.usb
[ 1.667773] hub 3-0:1.0: USB hub found
[ 1.671572] hub 3-0:1.0: 1 port detected
[ 1.676602] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 1.683274] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 1.691172] ohci-platform 1c1c400.usb: irq 40, io mem 0x01c1c400
[ 1.765804] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 1.774079] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.781294] usb usb4: Product: Generic Platform OHCI controller
[ 1.787219] usb usb4: Manufacturer: Linux 5.10.134 ohci_hcd
[ 1.792791] usb usb4: SerialNumber: 1c1c400.usb
[ 1.797749] hub 4-0:1.0: USB hub found
[ 1.801559] hub 4-0:1.0: 1 port detected
[ 1.806573] ALSA device list:
[ 1.809551] No soundcards found.
[ 2.011664] usb 3-1: new low-speed USB device number 2 using ohci-platform
[ 2.284680] usb 3-1: New USB device found, idVendor=045e, idProduct=0752, bcdDevice= 3.00
[ 2.292860] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.299987] usb 3-1: Product: Wired Keyboard 400
[ 2.304612] usb 3-1: Manufacturer: Microsoft
[ 2.411633] sunxi-mmc 1c11000.mmc: send stop command failed
[ 2.528550] mmc1: new high speed SDIO card at address 0001
[ 31.851667] dc5ldo: disabling
[ 31.854972] vdd1v2-sata: disabling
[ 31.858673] vdd2v5-sata: disabling