I can get serial setup, so that is no problem.
How far is the image, besides that you can't flash from web interface?
LAN ports working and switchports?
WIFI working (2.4ghz/5ghz)?
vlans, on switchports? vlans with wifi?
POE passtrough?
I can test all these features , so if you want please build an image.
As I gathered from @svanheule (please correct me if I'm wrong!):
You can find the images here in a few minutes.
@Borromini nicely summed up what's working and what isn't (thanks!)
I've pushed an additional commit to export the PoE passthrough enable GPIO, so you can use it in scripts or permanently enable with uci.
TP-Link's GPIO config file also has definitions related to the watchdog. I haven't done anything special with them, and the AP doesn't appear to spontaneously reboot, so that's probably fine.
;proc_name type active init gpio
;==========================================
wdt_feed wdt low high 4
wdt_disable wdt low high 3
I'm currently waiting for TP-Link to upload the GPL archive, so I can have a look at how they handle bringing up the switch.
No give me a few minutes building that one, and you'll need the initramfs image to tftpboot as well, that's not there for now either. Stay tuned.
@kroon040 New images have been uploaded, please note these builds will all self-configure to 10.0.0.254! Images contain LuCI.
@gashalot Could you give these a spin as well to see if they work on your EAP235-Wall? The ones I ordered specifically have (EU) printed on the back, so might be good to know if there's any hardware differences (or different compatibility checks) warranting a split-up in EU/US versions like other hardware.
Thnx @borromini,
So I need than first tftpboot the
openwrt-ramips-mt7621-tplink_eap235-wall-v1-initramfs-kernel.bin
and than scp the openwrt-ramips-mt7621-tplink_eap235-wall-v1-squashfs-factory.bin, or do I combine these with tftp?
And than scp the sysupgrade image and sysupgrade this image
You need to read the installation instructions as per the git commit. From what I understood you don't need the initramfs to install the factory image (you can do that through the web UI as per the instructions in the commit) but you will need the initramfs image to get the Ethernet going.
You should normally be able to write a sysupgrade image to flash from the initramfs, but I'm not sure if that's what @svanheule meant when he said you need to tftpboot to get the Ethernet ports working.
Hopefully he can clarify.
When you run tftpboot in the u-boot console, the bootloader will first initialise the internal switch, and then try to load the requested file.
On an uninterrupted boot, the bootloader does not initialise the switch. This means the OS still needs to do that, which currently isn't happening yet.
OK these are the steps
cliclientd stopcs, this should return "success"tftpboot, and boot image with bootm
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Do a sysupgrade, and with every reboot tftpboot is needed for the initramfs.bin
well, I got a bit working, booting form initramfs, the image is ofcourse readonly...
I noticed that there was only 1 radio 2.4ghz, on the image no 5ghz radio?
bootlog:
[ 0.000000] Linux version 5.4.92 (1800x@crunchbot) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15466+12-2e590a6364)) #0 SMP Sat Jan 23 21:08:30 2021
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TP-LINK EAP235-Wall v1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 14 pages/cpu s26736 r8192 d22416 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=000000c0
[ 0.000000] Readback ErrCtl register=000000c0
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 115216K/131072K available (5842K kernel code, 202K rwdata, 720K rodata, 7304K init, 230K bss, 15856K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x8069ea10 with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.015480] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[ 0.055829] pid_max: default: 32768 minimum: 301
[ 0.065177] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.079581] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097674] rcu: Hierarchical SRCU implementation.
[ 0.107774] smp: Bringing up secondary CPUs ...
[ 0.118335] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.118346] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.118358] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.118458] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.144933] Synchronize counters for CPU 1: done.
[ 0.215577] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.215585] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.215593] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.215652] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.243464] Synchronize counters for CPU 2: done.
[ 0.304593] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.304600] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.304608] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.304669] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.331066] Synchronize counters for CPU 3: done.
[ 0.390675] smp: Brought up 1 node, 4 CPUs
[ 0.402998] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.422285] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.436116] pinctrl core: initialized pinctrl subsystem
[ 0.447883] NET: Registered protocol family 16
[ 0.478376] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.499294] clocksource: Switched to clocksource GIC
[ 0.510799] NET: Registered protocol family 2
[ 0.520077] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.536615] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.551791] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.565783] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.578519] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.591424] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.605480] NET: Registered protocol family 1
[ 0.614048] PCI: CLS 0 bytes, default 32
[ 0.621879] random: fast init done
[ 8.191280] 4 CPUs re-calibrate udelay(lpj = 1163264)
[ 8.202885] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 8.227559] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 8.239050] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 8.261459] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 8.272775] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 8.284063] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 8.295811] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 8.309715] printk: console [ttyS0] disabled
[ 8.318146] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 8.336087] printk: console [ttyS0] enabled
[ 8.336087] printk: console [ttyS0] enabled
[ 8.352638] printk: bootconsole [early0] disabled
[ 8.352638] printk: bootconsole [early0] disabled
[ 8.373998] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 8.394836] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 8.404457] 8 fixed-partitions partitions found on MTD device spi0.0
[ 8.417106] Creating 8 MTD partitions on "spi0.0":
[ 8.426651] 0x000000000000-0x000000080000 : "u-boot"
[ 8.437674] 0x000000080000-0x000000090000 : "partition-table"
[ 8.450198] 0x000000090000-0x0000000a0000 : "product-info"
[ 8.462179] 0x0000000a0000-0x000000dc0000 : "firmware"
[ 8.474009] 2 tplink-fw partitions found on MTD device firmware
[ 8.485817] Creating 2 MTD partitions on "firmware":
[ 8.495721] 0x000000000000-0x00000022d9bb : "kernel"
[ 8.506637] 0x00000022d9bb-0x000000d20000 : "rootfs"
[ 8.517567] mtd: device 5 (rootfs) set to be root filesystem
[ 8.528971] 1 squashfs-split partitions found on MTD device rootfs
[ 8.541300] 0x000000900000-0x000000d20000 : "rootfs_data"
[ 8.553161] 0x000000dc0000-0x000000df0000 : "user-config"
[ 8.565027] 0x000000f30000-0x000000fb0000 : "mutil-log"
[ 8.576512] 0x000000fb0000-0x000000ff0000 : "oops"
[ 8.587187] 0x000000ff0000-0x000001000000 : "radio"
[ 8.599088] libphy: Fixed MDIO Bus: probed
[ 8.633629] libphy: mdio: probed
[ 8.640308] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 8.656041] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 8.674821] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 8.687742] NET: Registered protocol family 10
[ 8.697958] Segment Routing with IPv6
[ 8.705370] NET: Registered protocol family 17
[ 8.714525] 8021q: 802.1Q VLAN Support v1.8
[ 8.725030] gpio-export gpio-export: 1 gpio(s) exported
[ 8.735672] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 8.859707] libphy: dsa slave smi: probed
[ 8.868128] mt7530 mdio-bus:1f lan0 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 8.886068] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 8.904019] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 8.921907] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 8.940125] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 8.957725] DSA: tree 0 setup
[ 8.963935] rt2880-pinmux pinctrl: pcie is already enabled
[ 8.974869] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[ 8.989932] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 9.004851] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 9.119274] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 9.130383] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 9.241081] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 9.254951] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 9.264665] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 9.274381] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 9.293078] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 9.305747] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 9.319443] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 9.333137] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 9.344107] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 9.356101] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 9.368588] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]
[ 9.381141] pci 0000:00:00.0: supports D1
[ 9.389125] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 9.400911] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 9.412910] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 9.425395] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]
[ 9.437931] pci 0000:00:01.0: supports D1
[ 9.445915] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 9.458758] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 9.470774] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 9.483404] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 9.496789] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 9.507208] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 9.519354] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 9.532879] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 9.546240] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
[ 9.558259] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 9.572661] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 9.587057] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 9.601552] pci 0000:02:00.0: supports D1 D2
[ 9.610054] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 9.623277] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 9.652076] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 9.662491] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 9.674628] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 9.689016] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 9.702231] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 9.715407] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 9.729273] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 9.742444] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 9.756314] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 9.769835] pci 0000:00:01.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 9.784229] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 9.797754] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 9.811284] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 9.824804] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 9.838331] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 9.851857] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 9.861744] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 9.875276] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 9.888803] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 9.904244] pci 0000:02:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 9.919685] pci 0000:02:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 9.935115] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 9.945004] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 9.958523] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 9.973463] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 9.973856] hctosys: unable to open rtc device (rtc0)
[ 10.025845] Freeing unused kernel memory: 7304K
[ 10.034889] This architecture does not have kernel memory protection.
[ 10.047739] Run /init as init process
[ 10.870138] init: Console is alive
[ 10.877467] init: - watchdog -
[ 10.904421] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 10.922795] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 10.943601] init: - preinit -
[ 11.082126] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 11.098210] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.115061] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.183508] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.251594] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.287808] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.491464] mt7530 mdio-bus:1f lan0: configuring for phy/gmii link mode
[ 11.505059] 8021q: adding VLAN 0 to HW filter on device lan0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 15.607906] mt7530 mdio-bus:1f lan0: Link is Up - 1Gbps/Full - flow control off
[ 15.622637] IPv6: ADDRCONF(NETDEV_CHANGE): lan0: link becomes ready
[ 15.669677] mt7530 mdio-bus:1f lan0: Link is Down
[ 15.688466] procd: - early -
[ 15.694338] procd: - watchdog -
[ 16.239440] procd: - watchdog -
[ 16.246152] procd: - ubus -
[ 16.305095] procd: - init -
Please press Enter to activate this console.
[ 16.644097] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.728359] cryptodev: driver 1.11 loaded.
[ 16.737694] Mirror/redirect action on
[ 16.752515] u32 classifier
[ 16.757923] input device check on
[ 16.765208] Actions configured
[ 16.779857] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1
[ 16.794793] Backport generated by backports.git v5.8.18-1-0-ga630fd46
[ 16.801498] urngd: v1.0.2 started.
[ 16.894129] wireguard: WireGuard 1.0.20201112 loaded. See www.wireguard.com for information.
[ 16.910965] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 16.945905] xt_time: kernel timezone is -0000
[ 16.956766] random: crng init done
[ 16.963620] random: 7 urandom warning(s) missed due to ratelimiting
[ 17.003066] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[ 17.013887] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 17.025172] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 17.037337] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 17.668186] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 17.679357] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 17.715283] mt7603e 0000:01:00.0: firmware init done
[ 17.938610] PPP generic driver version 2.4.2
[ 17.949122] NET: Registered protocol family 24
[ 18.002121] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 42.064226] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 42.076845] mtk_soc_eth 1e100000.ethernet: PPE table busy
[ 42.094101] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 42.110107] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 42.113512] mt7530 mdio-bus:1f lan0: configuring for phy/gmii link mode
[ 42.140850] 8021q: adding VLAN 0 to HW filter on device lan0
[ 42.155104] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 42.168482] br-lan: port 1(lan0) entered blocking state
[ 42.178996] br-lan: port 1(lan0) entered disabled state
[ 42.190313] device lan0 entered promiscuous mode
[ 42.199674] device eth0 entered promiscuous mode
[ 42.226743] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 42.241145] 8021q: adding VLAN 0 to HW filter on device lan1
[ 42.256123] br-lan: port 2(lan1) entered blocking state
[ 42.266651] br-lan: port 2(lan1) entered disabled state
[ 42.278628] device lan1 entered promiscuous mode
[ 42.298735] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 42.312548] 8021q: adding VLAN 0 to HW filter on device lan2
[ 42.326912] br-lan: port 3(lan2) entered blocking state
[ 42.337474] br-lan: port 3(lan2) entered disabled state
[ 42.349291] device lan2 entered promiscuous mode
[ 42.366859] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 42.380707] 8021q: adding VLAN 0 to HW filter on device lan3
[ 42.395245] br-lan: port 4(lan3) entered blocking state
[ 42.405838] br-lan: port 4(lan3) entered disabled state
[ 42.417746] device lan3 entered promiscuous mode
[ 45.207911] mt7530 mdio-bus:1f lan0: Link is Up - 1Gbps/Full - flow control off
[ 45.222665] br-lan: port 1(lan0) entered blocking state
[ 45.233178] br-lan: port 1(lan0) entered forwarding state
[ 45.245404] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.31.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r15593+16-111de654af
-----------------------------------------------------
Hardware: TP-LINK EAP235-Wall v1
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
That sounds like what you get when you forget to include the packages for the 5GHz radio. @Borromini, did you include the required packages in your build?
My bad! I'm using PER_DEVICE_ROOTFS and not all my MT7621 devices have the same hardware, so those packages were modular...
New build on the way.
New images are up, necessary packages included.
@svanheule Seems there's other TP-Link MT7621 devices suffering from similar PHY initialisation issues:
No solution offered there but thought I'd mention it.
This location I took the packages
https://volatilesystems.org/dl/lede/targets/eap235-wall/
did an sysupgrade en placed the new initramfs file in tftplocation, but still only 2.4ghz
dmesg shows this time, and should be correct I think
[ 0.000000] Linux version 5.4.92 (1800x@crunchbot) (gcc version 8.4.0 (OpenWr
t GCC 8.4.0 r15466+12-2e590a6364)) #0 SMP Sun Jan 24 16:29:08 2021
@kroon040 Can you checksum the image you tried and see if it matches these?
https://volatilesystems.org/dl/lede/targets/eap235-wall/images_wip/
Those should have the mt7615e driver and mt7663 firmware.
@kroon040 Can you post the output of this command:
# opkg list-installed|grep mt76
Edit: sorry for the teething problems guys. kmod-mt7615e doesn't auto-select kmod-mt7663-firmware-ap so I had to add that explicitly to DEVICE_PACKAGES. New images are up.
@Borromini , now I have no wireless at all, also no menu entry
root@OpenWrt:/etc/init.d# opkg list-installed|grep mt76
gives nothing
