Confirmed 24.10.2 working on a RB01 with all the caveats. Used xmir-patcher to enable flashing through telnet as described on the wiki ("enable mesh telnet" did not work, and I didn't bother with the other remaining methords). Newer stock uboot, Reboot counter set to 8, that increased to 9 without issue.
1 Like
Using the XMiR-Patcher method allows you to read all of the device's information and dump it into a .txt file. From there, you can look for the bootloader's build time:
➜ xmir-patcher git:(main) ✗ grep BuildTime full_info.txt
BuildTime: Fri, 20 May 2022 10:18:01 +0000
1 Like
I was running 23.X and I tried to update it to the latest 24.10. The Web UI said that the layout has changed or something and that I need to install the factory image. So, I downloaded the factory.bin and installed it. I think my router is bricked. I cannot connect to it. It seems that the Ethernet port does not even work. The ‘system’ lamp shows solid orange.
In this case, what am I supposed to? Is there an easy way to get back to 23.X or get 24.10 working here (I have backed up the settings)? Or, do I need to use the ‘debricking’ method https://openwrt.org/toh/xiaomi/ax3200#debricking , which seems to install the stock firmware?
Follow TFTP recovery method. And then just make fresh install of 24.10.2 with xmir patcher. Original 24.10.0 image was broken it has been reported many times.
1 Like
Finally, I fixed everything, but it took my whole Sunday afternoon. I flashed the ‘favourable’ image and then used the XMIR patcher. I wish the download page ( https://firmware-selector.openwrt.org/?target=mediatek%2Fmt7622&id=xiaomi_redmi-router-ax6s ) had some kind of warning for the upgrade, when the upgrade can break the system. I saw that the manual page ( https://openwrt.org/toh/xiaomi/ax3200#upgrading_openwrt ) had that warning, but people would not read the manual again each time they update existing OpenWRT.
Also, the Debricking part had some conflicting description that wasted my time. Below the commands, it says that I need to wait 10 minute and then reboot the router, but above the commands, it says that when the router flashes blue in a few seconds, I can reboot the router. No need to wait 10 minutes.
1 Like
Don’t forget about softbrick after 6 reboots or you will need to repeat procedure…
现在5G无法正常开启有解决办法了吗
现在5G无法正常开启有解决办法了吗
You’re going to want to use English (even if auto translated) on this forum, it’s the preferred language.
Here’s the Google translated version
Is there any solution for the 5G not turning on properly?
Try plugging off power cable completely. Whenever I enable WED and then disable it, 5GHz stops working. Same problem with hardware offloading tables. They are not properly initialized, entries from previous session survive router reboot (and even reset!). I wrote about it already but no one seems to care enough.
1 Like
Just in case, 24.10.3 sysupgrade went smooth too.
Did you do an attended sysupgrade? That is not working for me. It builds the image uploads it to the device and then nothing. Openwrt reloads and I’m stuck at 24.10.2. No entries in the log.
I’ve also tried owut upgrad, but the same thing happens. I see my firmware.bin in /tmp.
I must say, the reboot command also does nothing, only reboot -f works for me.
Tried it with and without updating my packages. I’m stuck at 24.10.2.
I used regular sysupgrade image.
Fixed. I apparently had a corrupt install of nginx on my router. Couldn’t repair, reinstall or remove it with opkg. Remove eveything by hand and presto. Reboot worked again and so did attended sysupgrade. Phew.
I week ago I’ve upgraded my AX6S from 23.05.5 to 24.10.2 and I’ve got stranger things happening with 5GHz wifi. Randomly approx. once in a couple of days the 5GHz dies and I see this message spamming in the syslog every 6 seconds:
Thu Sep 25 23:05:38 2025 daemon.err hostapd: Failed to set beacon parameters
Restarting the whole Phy helps. But I’ve never yet detected the beginning of this situation to catch the logs (if there is something at all).
Whatever…. doesn’t anyone else happen to have the same glitch?
Never saw it. Why don't you upgrade to 24.10.3? It has plenty of fixes (and, probably, bugs) in mac80211 subsystem.
A week ago it wasn’t available. Now it takes time because the plain attended sysupgrade doesn’t work for me while I have a couple of sideloaded packages (namely amneziawg VPN stuff). So need to find time to do everything.
wed is still broken at 24.10.3
hi there, after the recent snapshot versions ( as the one today r31448-7ef19bb9cd ), when i reboot the devices, both wifi 2.4 and 5G are disabled. If i restart them either by luci or with wifi command, both came online. Is this a known issue?
Probably similar to this. Although I don't experience it the way you describe it.
Thanks for looking in. I just did and it’s the same. Here is in Luci how the interfaces are:
Below the dmesg. Note after i issued wifi and the result follows after 119s. I see nothing wrong. It happens with default wifi configuration also. Model is RB01. A snapshot of 1 sept. does not have the issue.
Happy to provide any other information. I’ll mitigate the issue by issuing a wifi after the boot finishes.
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.12.51 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r31448-7ef19bb9cd) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Wed Oct 15 11:54:09 2025
[ 0.000000] Machine model: Xiaomi Redmi Router AX6S
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: legacy bootconsole [uart8250] enabled
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] percpu: Embedded 20 pages/cpu s42584 r8192 d31144 u81920
[ 0.000000] pcpu-alloc: s42584 r8192 d31144 u81920 alloc=204096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] CPU features: detected: ARM erratum 843419
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 swiotlb=512 ubi.block=0,fit root=/dev/fit0
[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65536
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: area num 2.
[ 0.000000] software IO TLB: mapped [mem 0x000000004f900000-0x000000004fa00000] (1MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.008277] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
[ 0.018676] pid_max: default: 32768 minimum: 301
[ 0.026089] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.033346] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.043946] rcu: Hierarchical SRCU implementation.
[ 0.048759] rcu: Max phase no-delay instances is 1000.
[ 0.054174] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.062509] smp: Bringing up secondary CPUs ...
[ 0.067457] Detected VIPT I-cache on CPU1
[ 0.067537] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.067611] smp: Brought up 1 node, 2 CPUs
[ 0.082294] SMP: Total of 2 processors activated.
[ 0.087010] CPU: All CPU(s) started at EL2
[ 0.091119] CPU features: detected: 32-bit EL0 Support
[ 0.096273] CPU features: detected: CRC32 instructions
[ 0.101452] alternatives: applying system-wide alternatives
[ 0.107184] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.115678] Memory: 239576K/262144K available (9600K kernel code, 930K rwdata, 2772K rodata, 448K init, 319K bss, 20904K reserved, 0K cma-reserved)
[ 0.132516] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.142420] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.149293] 29200 pages in range for non-PLT usage
[ 0.149297] 520720 pages in range for PLT usage
[ 0.155543] pinctrl core: initialized pinctrl subsystem
[ 0.167637] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.173860] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.180967] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.188757] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.197114] thermal_sys: Registered thermal governor 'fair_share'
[ 0.197119] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.203232] thermal_sys: Registered thermal governor 'step_wise'
[ 0.209264] thermal_sys: Registered thermal governor 'user_space'
[ 0.215360] ASID allocator initialised with 65536 entries
[ 0.227539] pstore: Using crash dump compression: deflate
[ 0.232967] pstore: Registered ramoops as persistent store backend
[ 0.239167] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.251154] /pcie@1a143000: Fixed dependency cycle(s) with /pcie@1a143000/interrupt-controller
[ 0.271764] cryptd: max_cpu_qlen set to 1000
[ 0.277136] SCSI subsystem initialized
[ 0.281034] libata version 3.00 loaded.
[ 0.286224] clocksource: Switched to clocksource arch_sys_counter
[ 0.294534] NET: Registered PF_INET protocol family
[ 0.299551] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.308035] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.316435] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.324212] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.332004] TCP bind hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.339225] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.345882] MPTCP token hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.353228] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.359796] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.366968] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.372675] PCI: CLS 0 bytes, default 64
[ 0.377652] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.388932] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.394787] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.457242] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.465939] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm"
[ 0.484032] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
[ 0.497210] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.506921] printk: legacy console [ttyS0] disabled
[ 0.532296] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 118, base_baud = 1562500) is a ST16650V2
[ 0.541624] printk: legacy console [ttyS0] enabled
[ 0.551223] printk: legacy bootconsole [uart8250] disabled
[ 0.563107] mtk_rng 1020f000.rng: registered RNG driver
[ 0.568777] random: crng init done
[ 0.574546] loop: module loaded
[ 0.578330] mtk-ecc 1100e000.ecc: probed
[ 0.583433] spi-nand spi0.0: ESMT SPI NAND was found.
[ 0.588528] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.596709] mtk-snand 1100d000.spi: ECC strength: 4 bits per 512 bytes
[ 0.604562] [BBT] BMT.v2 is found at 0x3ff
[ 0.608966] 10 fixed-partitions partitions found on MTD device spi0.0
[ 0.615423] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.621708] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.628180] Creating 10 MTD partitions on "spi0.0":
[ 0.633053] 0x000000000000-0x000000080000 : "Preloader"
[ 0.639164] 0x000000080000-0x0000000c0000 : "ATF"
[ 0.644493] 0x0000000c0000-0x000000140000 : "u-boot"
[ 0.650230] 0x000000140000-0x000000180000 : "u-boot-env"
[ 0.656021] 0x000000180000-0x0000001c0000 : "bdata"
[ 0.661400] 0x0000001c0000-0x000000240000 : "factory"
[ 0.667253] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.673694] 0x000000240000-0x000000280000 : "crash"
[ 0.679116] 0x000000280000-0x0000002c0000 : "crash_log"
[ 0.684834] 0x0000002c0000-0x000000340000 : "ubi-loader"
[ 0.690919] 0x000000340000-0x0000075c0000 : "ubi"
[ 0.819671] ubi0: default fastmap pool size: 45
[ 0.824199] ubi0: default fastmap WL pool size: 22
[ 0.828991] ubi0: attaching mtd9
[ 1.127764] ubi0: scanning is finished
[ 1.135626] ubi0: attached mtd9 (name "ubi", size 114 MiB)
[ 1.141124] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.147998] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.154778] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.161736] ubi0: good PEBs: 916, bad PEBs: 0, corrupted PEBs: 0
[ 1.167739] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.174954] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1750711236
[ 1.184083] ubi0: available PEBs: 0, total reserved PEBs: 916, PEBs reserved for bad PEB handling: 19
[ 1.193310] ubi0: background thread "ubi_bgt0d" started, PID 298
[ 1.193748] block ubiblock0_0: created from ubi0:0(fit)
[ 1.330478] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc081840000, irq 123
[ 1.340268] i2c_dev: i2c /dev entries driver
[ 1.345810] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.355457] NET: Registered PF_INET6 protocol family
[ 1.361298] Segment Routing with IPv6
[ 1.364983] In-situ OAM (IOAM) with IPv6
[ 1.368979] NET: Registered PF_PACKET protocol family
[ 1.374044] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.387302] 8021q: 802.1Q VLAN Support v1.8
[ 1.410635] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 1.417332] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 1.423167] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 1.662862] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 1.669081] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.674566] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 1.681448] pci_bus 0000:00: scanning bus
[ 1.685709] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400 PCIe Root Port
[ 1.693209] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x1ffffffff 64bit pref]
[ 1.700251] pci 0000:00:00.0: PCI bridge to [bus 00]
[ 1.705283] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.714773] pci_bus 0000:00: fixups for bus
[ 1.718979] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.725677] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.733754] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.740833] pci_bus 0000:01: scanning bus
[ 1.745036] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280 PCIe Endpoint
[ 1.752444] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit pref]
[ 1.759429] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00003fff 64bit pref]
[ 1.766412] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00000fff 64bit pref]
[ 1.774068] pci 0000:01:00.0: supports D1 D2
[ 1.778340] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.784974] pci 0000:01:00.0: PME# disabled
[ 1.789490] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.816431] pci_bus 0000:01: fixups for bus
[ 1.820615] pci_bus 0000:01: bus scan returning with max=01
[ 1.826187] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.832826] pci_bus 0000:00: bus scan returning with max=01
[ 1.838421] pci 0000:00:00.0: BAR 0 [mem size 0x200000000 64bit pref]: can't assign; no space
[ 1.846953] pci 0000:00:00.0: BAR 0 [mem size 0x200000000 64bit pref]: failed to assign
[ 1.854958] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]: assigned
[ 1.862447] pci 0000:01:00.0: BAR 0 [mem 0x20000000-0x200fffff 64bit pref]: assigned
[ 1.870276] pci 0000:01:00.0: BAR 2 [mem 0x20100000-0x20103fff 64bit pref]: assigned
[ 1.878102] pci 0000:01:00.0: BAR 4 [mem 0x20104000-0x20104fff 64bit pref]: assigned
[ 1.885922] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.890890] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
[ 1.897685] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 1.906726] pci_bus 0000:00: resource 4 [mem 0x20000000-0x27ffffff]
[ 1.912987] pci_bus 0000:01: resource 1 [mem 0x20000000-0x201fffff]
[ 1.919377] pcieport 0000:00:00.0: assign IRQ: got 127
[ 1.924517] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 1.930627] pcieport 0000:00:00.0: enabling bus mastering
[ 1.936079] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x452650c0
[ 1.943461] pcieport 0000:00:00.0: PME: Signaling with IRQ 127
[ 1.949366] pcieport 0000:00:00.0: save config 0x00: 0x325814c3
[ 1.955282] pcieport 0000:00:00.0: save config 0x04: 0x00100006
[ 1.961202] pcieport 0000:00:00.0: save config 0x08: 0x06040000
[ 1.967121] pcieport 0000:00:00.0: save config 0x0c: 0x00010000
[ 1.973035] pcieport 0000:00:00.0: save config 0x10: 0x0000000c
[ 1.978958] pcieport 0000:00:00.0: save config 0x14: 0x00000000
[ 1.984872] pcieport 0000:00:00.0: save config 0x18: 0x40010100
[ 1.990792] pcieport 0000:00:00.0: save config 0x1c: 0x04200000
[ 1.996711] pcieport 0000:00:00.0: save config 0x20: 0x20102000
[ 2.002625] pcieport 0000:00:00.0: save config 0x24: 0x00000000
[ 2.008543] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[ 2.014457] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[ 2.020375] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[ 2.026294] pcieport 0000:00:00.0: save config 0x34: 0x00000050
[ 2.032208] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[ 2.038129] pcieport 0000:00:00.0: save config 0x3c: 0x0002017f
[ 2.044131] OF: /pcie@1a143000/pcie@0,0: Missing device_type
[ 2.050557] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 2.058611] FIT: Detected U-Boot 2024.10-OpenWrt-r28739-d9340319c6
[ 2.064795] FIT: Selected configuration: "config-1" (OpenWrt xiaomi_redmi-router-ax6s)
[ 2.072761] FIT: kernel sub-image 0x00001000..0x005fbf7a "kernel-1" (ARM64 OpenWrt Linux-6.12.51)
[ 2.082606] FIT: flat_dt sub-image 0x005fc000..0x00603330 "fdt-1" (ARM64 OpenWrt xiaomi_redmi-router-ax6s device tree blob)
[ 2.094623] FIT: filesystem sub-image 0x00604000..0x00a7dfff "rootfs-1" (ARM64 OpenWrt xiaomi_redmi-router-ax6s rootfs)
[ 2.106414] block ubiblock0_0: mapped 1 uImage.FIT filesystem sub-image as /dev/fit0
[ 2.170059] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 2.179192] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 2.189206] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=129)
[ 2.210364] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=130)
[ 2.231298] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=131)
[ 2.252203] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=132)
[ 2.263382] mtk_soc_eth 1b100000.ethernet eth0: entered promiscuous mode
[ 2.270120] DSA: tree 0 setup
[ 2.273351] clk: Disabling unused clocks
[ 2.277569] PM: genpd: Disabling unused power domains
[ 2.285601] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 2.292953] Freeing unused kernel memory: 448K
[ 2.297441] Run /sbin/init as init process
[ 2.301529] with arguments:
[ 2.304487] /sbin/init
[ 2.307195] with environment:
[ 2.310327] HOME=/
[ 2.312677] TERM=linux
[ 2.495147] init: Console is alive
[ 2.498758] init: - watchdog -
[ 2.839018] kmodloader: loading kernel modules from /etc/modules-boot.d/
[ 2.862393] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.872622] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.885470] init: - preinit -
[ 3.202994] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 3.211576] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 3.226860] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 4.654510] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 7.459226] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 7.465006] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 781
[ 7.483149] UBIFS (ubi0:1): recovery needed
[ 7.566285] UBIFS (ubi0:1): recovery completed
[ 7.570810] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 7.578658] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.588589] UBIFS (ubi0:1): FS size: 100691968 bytes (96 MiB, 793 LEBs), max 804 LEBs, journal size 5079040 bytes (4 MiB, 40 LEBs)
[ 7.600338] UBIFS (ubi0:1): reserved for root: 4755930 bytes (4644 KiB)
[ 7.606961] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID A02C9B3F-2D3B-47DD-B127-FD58599FE0CE, small LPT model
[ 7.623149] mount_root: switching to ubifs overlay
[ 7.630945] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 7.645193] urandom-seed: Seeding with /etc/urandom.seed
[ 7.703130] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 7.716100] procd: - early -
[ 7.719094] procd: - watchdog -
[ 8.269209] procd: - watchdog -
[ 8.274215] procd: - ubus -
[ 8.347430] procd: - init -
[ 8.670354] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.702179] Loading modules backported from Linux version v6.16-0-g038d61fd6422
[ 8.709555] Backport generated by backports.git v6.1.145-1-47-g6194bf852a3e
[ 8.771395] mt7622-wmac 18000000.wmac: registering led 'mt76-phy0'
[ 8.826754] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 8.841404] mt7915e 0000:01:00.0: assign IRQ: got 127
[ 8.846566] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
[ 8.852677] mt7915e 0000:01:00.0: enabling bus mastering
[ 8.901501] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
[ 8.901501]
[ 8.966449] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x452650c0
[ 8.998958] urngd: v1.0.2 started.
[ 9.001123] mt7622-wmac 18000000.wmac: N9 Firmware Version: reserved, Build Time: 20220630094834
[ 9.074019] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20240429200716a
[ 9.074019]
[ 9.264235] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20240429200752
[ 9.288207] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20240429200812
[ 9.403981] mt7915e 0000:01:00.0: registering led 'mt76-phy1'
[ 9.491856] PPP generic driver version 2.4.2
[ 9.497818] NET: Registered PF_PPPOX protocol family
[ 9.506929] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.173078] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 12.187413] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 12.201377] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 12.208443] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 12.218106] br-lan: port 1(lan1) entered blocking state
[ 12.223343] br-lan: port 1(lan1) entered disabled state
[ 12.228672] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[ 12.234949] mtk_soc_eth 1b100000.ethernet eth0: entered allmulticast mode
[ 12.245009] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[ 12.261522] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 12.272281] br-lan: port 2(lan2) entered blocking state
[ 12.277603] br-lan: port 2(lan2) entered disabled state
[ 12.282873] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
[ 12.291016] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
[ 12.306207] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 12.317933] br-lan: port 3(lan3) entered blocking state
[ 12.323179] br-lan: port 3(lan3) entered disabled state
[ 12.328497] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
[ 12.337132] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
[ 12.374865] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[ 14.777341] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 14.777420] br-lan: port 1(lan1) entered blocking state
[ 14.790529] br-lan: port 1(lan1) entered forwarding state
[ 119.498139] br-lan: port 4(wl0-ap0) entered blocking state
[ 119.503646] br-lan: port 4(wl0-ap0) entered disabled state
[ 119.509200] mt7622-wmac 18000000.wmac wl0-ap0: entered allmulticast mode
[ 119.516102] mt7622-wmac 18000000.wmac wl0-ap0: entered promiscuous mode
[ 119.631464] br-lan: port 4(wl0-ap0) entered blocking state
[ 119.636985] br-lan: port 4(wl0-ap0) entered forwarding state
[ 119.968287] br-lan: port 5(wl1-ap0) entered blocking state
[ 119.973788] br-lan: port 5(wl1-ap0) entered disabled state
[ 119.979369] mt7915e 0000:01:00.0 wl1-ap0: entered allmulticast mode
[ 119.985830] mt7915e 0000:01:00.0 wl1-ap0: entered promiscuous mode